Table of Contents
Advertisement
Quick Links
Questo manuale d'istruzione è fornito da trovaprezzi.it. Scopri tutte le offerte per
Ace
Quick Start
Thank you for purchasing the MSI®
motherboard. This Quick Start section provides demonstration diagrams about how
to install your computer. Some of the installations also provide video demonstrations.
Please link to the URL to watch it with the web browser on your phone or tablet. You
may have even link to the URL by scanning the QR code.
Preparing Tools and Components
Intel® LGA1200 CPU
DDR4 Memory
Thermal Paste
Phillips Screwdriver
o cerca il tuo prodotto tra le
MEG Z590 ACE / MEG Z590 ACE GOLD EDITION
Power Supply Unit
SATA Hard Disk Drive
migliori offerte di Schede Madri
CPU Fan
A Package of Screws
MSI MEG Z590
Chassis
Graphics Card
SATA DVD Drive
Quick Start
1
Advertisement
Table of Contents
Related Manuals for MSI MEG Z590 ACE
Summary of Contents for MSI MEG Z590 ACE
-
Page 1: Quick Start
Schede Madri Quick Start Thank you for purchasing the MSI® MEG Z590 ACE / MEG Z590 ACE GOLD EDITION motherboard. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. -
Page 2: Safety Information
Safety Information ∙ The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly. ∙ Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start. -
Page 3: Case Stand-Off Notification
Case stand-off notification Before installing the motherboard into the case, install first the necessary mounting stand-off required for a motherboard on the mounting plate in the case. To prevent damage to the motherboard, any unnecessary mounting stand-off between the motherboard circuits and the computer case is prohibited. The Case standoff keep out zone signs will be marked on the backside of motherboard (as shown below) to serve as a warning to user. -
Page 4: Installing A Processor
Installing a Processor ⚽ https://youtu.be/4ce91YC3Oww Quick Start... -
Page 5: Installing Ddr4 Memory
Installing DDR4 memory ⚽ http://youtu.be/T03aDrJPyQs DIMMA1 DIMMA2 DIMMA2 DIMMA2 DIMMB1 DIMMB2 DIMMB2 Quick Start... -
Page 6: Connecting The Front Panel Header
Connecting the Front Panel Header ⚽ http://youtu.be/DPELIdVNZUI Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch JFP1 Reset Switch Power Switch Reserved No Pin HDD LED - HDD LED HDD LED +... -
Page 7: Installing The Motherboard
Installing the Motherboard ⚽ https://youtu.be/wWI6Qt51Wnc Torque: 3 kgf·cm* *3 kgf·cm = 0.3 N·m = 2.6 lbf·in Quick Start... -
Page 8: Connecting The Power Connectors
Connecting the Power Connectors ⚽ http://youtu.be/gkDYyR_83I4 ATX_PWR1 CPU_PWR2 PCIE_PWR1 CPU_PWR1 Quick Start... -
Page 9: Installing Sata Drives
Installing SATA Drives ⚽ http://youtu.be/RZsMpqxythc Quick Start... -
Page 10: Installing A Graphics Card
Installing a Graphics Card ⚽ http://youtu.be/mG0GZpr9w_A Quick Start... -
Page 11: Connecting Peripheral Devices
Connecting Peripheral Devices Quick Start... -
Page 12: Power On
Power On Quick Start... -
Page 13: Table Of Contents
Contents Quick Start ......................1 Preparing Tools and Components................1 Safety Information ....................2 Case stand-off notification ..................3 Installing a Processor .................... 4 Installing DDR4 memory ..................5 Connecting the Front Panel Header ..............6 Installing the Motherboard ..................7 Connecting the Power Connectors ................ - Page 14 Boot Phases ......................56 Debug Code LED Table ..................56 ACPI States Codes ....................60 CPU Temperature ....................60 Installing OS, Drivers & MSI Center ..............61 Installing Windows® 10 ..................61 Installing Drivers ....................61 MSI Center ......................61 Nahimic 3 ......................
- Page 15 Resetting BIOS ...................... 67 Updating BIOS ....................... 67 RAID Configuration ....................69 Intel® Optane™ Memory Configuration .............. 70 Troubleshooting ....................71 Contents...
-
Page 16: Specifications
∙ Supports Dual-Channel mode ∙ Supports non-ECC, un-buffered memory ∙ Supports Intel® Extreme Memory Profile (XMP) *Please refer to www.msi.com for more information on compatible memory ∙ 3x PCIe x16 slots ▪ Support x16/x0/x4, x8/x8/x4, x8/x4+x4/x4 ▪ PCI_E1 & PCI_E3 slots (From CPU) ▫... - Page 17 *** M2_4 bandwidth will switch from x4 to x2 when PCI_E5 slot is inserted. **** Before using Intel® Optane™ memory modules, please ensure that you have updated the drivers and BIOS to the latest version from MSI website. ∙ Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA...
- Page 18 Continued from previous column ∙ Intel® Z590 Chipset ▪ 3x USB 3.2 Gen 2 10Gbps ports (2 Type-A port on the back panel, 1 Type-C internal connector) ▪ 6x USB 3.2 Gen 1 5Gbps ports (4 Type-A port on the back panel, 2 ports available through internal USB connector) ▪...
- Page 19 Continued from previous column ∙ 1x 24-pin ATX main power connector ∙ 2x 8-pin ATX 12V power connectors ∙ 1x 6-pin PCIE power connector ∙ 6x SATA 6Gb/s connectors ∙ 4x M.2 slots (M-Key) ∙ 1x USB 3.2 Gen 2 10Gbps Type-C connector ∙...
- Page 20 ∙ Drivers ∙ MSI Center ∙ Intel Extreme Tuning Utility ∙ Nahimic Audio Software ∙ MSI APP Player (Bluestack) ∙ Open Broadcaster Software (OBS) ∙ CPU-Z MSI GAMING ∙ Google Chrome™, Google Toolbar, Google Drive ∙ Norton™ Internet Security Solution...
- Page 21 Continued from previous column ∙ Duet Display ∙ MSI Sound Tune ∙ Gaming Mode ∙ Creator Mode ∙ Mystic Light ∙ Ambient Link ∙ LAN Manager (Powered By cFosSpeed) MSI Center Features ∙ User Scenario ∙ Monitor ∙ Frozr AI Cooling ∙...
- Page 22 Continued from previous column ∙ LED ▪ Mystic Light ▪ Mystic Light Extension (RGB) ▪ Mystic Light Extension (RAINBOW) ▪ Mystic Light Extension (CORSAIR) ▪ Mystic Light SYNC ▪ Ambient Link ▪ EZ LED Control ▪ EZ DEBUG LED ∙ Performance ▪...
-
Page 23: Jcorsair1 Connector Specification
▪ DDR4 Steel Armor ▪ PCI-E Steel Armor ▪ Pre-installed I/O Shield ∙ Experience ▪ Smart Button Special Features ▪ MSI Center ▪ Duet Display ▪ Frozr AI Cooling ▪ Click BIOS 5 ▪ System Saver ▪ Flash BIOS Button... -
Page 24: Package Contents
Package contents Please check the contents of your motherboard package. It should contain: Motherboard MEG Z590 ACE / MEG Z590 ACE GOLD EDITION User manual Documentation Quick guide Quick installation guide Application USB drive with drivers & utilities SATA 6Gb/s cables... -
Page 25: Block Diagram
Block Diagram PCI_E1 PCIe x16 PCI_E3 DDR4 2Channel PCIe x8 DIMM A1,A2 DIMM B1,B2 M2_1 DMI x8 PCI_E2 USB 3.2 Gen 2 10Gbps PCI_E4 USB 3.2 Gen 1 5Gbps M2_2 M2_3 SATA5/6 USB 2.0 M2_4 PCI_E5 USB 2.0 Hub-GL850G Thunderbolt SATA1/2/3/4 Intel LAN I225 WiFi AX210... -
Page 26: Rear I/O Panel
Rear I/O Panel Flash BIOS Port Thunderbolt 4 Audio Ports (USB-C) 2.5 Gbps USB 2.0 Clear CMOS button Flash BIOS Mini DisplayPort Optical Button Input (for Thunderbolt S/PDIF-Out passthrough) USB 3.2 Gen 1 USB 3.2 Gen 2 Wi-Fi 6E 5Gbps Type A 10Gbps Type A ∙... -
Page 27: Realtek Audio Console
Realtek Audio Console After Realtek Audio Console is installed. You can use it to change sound settings to get better sound experience. Application Enhancement Device Selection Main Volume Connector Settings Jack Status ∙ Device Selection - allows you to select a audio output source to change the related options. - Page 28 Audio jacks to headphone and microphone diagram Audio jacks to stereo speakers diagram AUDIO INPUT Audio jacks to 7.1-channel speakers diagram AUDIO INPUT Rear Front Side Center/ Subwoofer Rear I/O Panel...
-
Page 29: Installing Antennas
Installing Antennas 1. Combine the antenna with the base. 2. Screw two antenna cables tight to the WiFi antenna connectors as shown. 3. Place the antenna as high as possible. Rear I/O Panel... -
Page 30: Connecting Thunderbolt Devices Via Daisy-Chain
Connecting Thunderbolt Devices via Daisy-chain Daisy-chain is a method of connecting multiple devices to a PC with only one output terminal. Daisy-chain allows you to connect multiple thunderbolt devices to a single thunderbolt port on the back panel. You can also daisy chain monitor by connecting graphics card to the Mini DisplayPort Input port on the back panel. -
Page 31: Overview Of Components
Overview of Components CPU_FAN1 Processor PUMP_FAN1 Socket JCORSAIR1 JRAINBOW2 CPU_PWR2 CPU_PWR1 DIMMA1 DIMMA2 DIMMB1 DIMMB2 SYS_FAN5 ATX_PWR1 JUSB4 M2_1 SYS_FAN1 PCI_E1 JUSB3 M2_2 SATA▼1▲2 M2_3 PCI_E2 SATA▼3▲4 PCI_E3 SATA▼5▲6 JTPM1 M2_4 JSLOW1 PCI_E4 SYS_FAN6 JLN2, JLN1 JOC_FS1 PCI_E5 JFP2 JBAT1 JAUD1 JFP1 JCI1... - Page 32 Component Contents Port Name Port Type Page BIOS_SW1 Multi-BIOS Switch CPU_FAN1, PUMP_FAN1, Fan Connectors SYS_FAN1~6 CPU_PWR1~2, ATX_PWR1, Power Connectors PCIE_PWR1 CPU Socket LGA1200 CPU Socket DIMM Slots Memory slots JAUD1 Front Audio Connector JBAT1 Clear CMOS (Reset BIOS) Jumper JCI1 Chassis Intrusion Connector JCORSAIR1 CORSAIR Connector...
-
Page 33: Cpu Socket
∙ the CPU. ∙ Please retain the CPU protective cap after installing the processor. MSI will deal with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket. When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink ∙... -
Page 34: Dimm Slots
It is recommended to use a more efficient memory cooling system for full DIMMs ∙ installation or overclocking. The stability and compatibility of installed memory module depend on installed CPU ∙ and devices when overclocking. ∙ Please refer to www.msi.com for more information on compatible memory. Overview of Components... -
Page 35: Pci_E1~5: Pcie Expansion Slots
PCI_E1~5: PCIe Expansion Slots PCI_E1: PCIe 4.0 x16 (From CPU) PCI_E2: PCIe 3.0 x1 (From Z590 chipset) PCI_E3: PCIe 4.0 x8 (From CPU) PCI_E4: PCIe 3.0 x1 (From Z590 chipset) PCI_E5: PCIe 3.0 x4 (From Z590 chipset) Multiple graphics cards installation recommendation Overview of Components... - Page 36 ⚠ Important If you install a large and heavy graphics card, you need to use a tool such as MSI ∙ Graphics Card Bolster to support its weight to prevent deformation of the slot. For a single PCIe x16 expansion card installation with optimum performance, using ∙...
-
Page 37: M2_1~4: M.2 Slots (Key M)
M2_1~4: M.2 Slots (Key M) ⚽ Video Demonstration Watch the video to learn how to Install M.2 SSD. https://youtu.be/2UeWMgjwogU M2_1 M2_2 M2_3 M2_4 ⚠ Important Intel® RST only supports PCIe M.2 SSD with UEFI ROM. ∙ ∙ Intel® Optane™ Memory Ready for M2_2, M2_3 and M2_4 slots. Installing M.2 module 1. - Page 38 3. Secure the supplied M.2 standoff according to your M.2 SSD length if need. 4. Insert your M.2 SSD into the M.2 slot at a 30-degree angle. 5. Secure the M.2 SSD in place with the supplied M.2 8.5H screw. ⚠...
-
Page 39: Sata1~6: Sata 6Gb/S Connectors
SATA1~6: SATA 6Gb/s Connectors These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device. SATA2 SATA1 SATA4 SATA3 SATA6 SATA5 ⚠ Important Please do not fold the SATA cable at a 90-degree angle. Data loss may result during ∙... -
Page 40: Jfp1, Jfp2: Front Panel Connectors
JFP1, JFP2: Front Panel Connectors These connectors connect to the switches and LEDs on the front panel. Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED -... -
Page 41: Cpu_Pwr1~2, Atx_Pwr1, Pcie_Pwr1: Power Connectors
CPU_PWR1~2, ATX_PWR1, PCIE_PWR1: Power Connectors These connectors allow you to connect an ATX power supply. CPU_PWR1~2 Ground +12V Ground +12V Ground +12V Ground +12V +3.3V +3.3V +3.3V -12V Ground Ground PS-ON# Ground Ground Ground ATX_PWR1 Ground Ground PWR OK 5VSB +12V +12V +3.3V... -
Page 42: Jslow1: Slow Mode Booting Jumper
JSLOW1: Slow Mode Booting Jumper This jumper is used for LN2 cooling solution, that provides the extreme overclocking conditions, to boot at a stable processor frequency and to prevent the system from crashing. Normal Enabled (Default) (Please enable this jumper during BIOS POST.) JLN1~2: Low Temperature Booting Jumper This jumper is used for liquid nitrogen cooling system to boot at an extreme low... -
Page 43: Joc_Fs1: Safe Boot Jumper
JOC_FS1: Safe Boot Jumper This jumper is used for Safe Boot. Once enabled, the system will boot with default settings and lower PCIe (from CPU) mode. Normal Enabled (default) Apply the BIOS default settings and lower PCIe Boot with the saved (from CPU) mode for BIOS settings. -
Page 44: T_Sen1: Thermal Sensor Connector
T_SEN1: Thermal Sensor Connector This connector allows you to connect the thermistor cable and use it to monitor the temperature of the detection point. Thermistor cable Sense V-Check Points Lite These voltage checkpoints are used to measure the current system voltages. A multimeter (not included) will be required to check voltages. -
Page 45: Jusb3: Usb 3.2 Gen 1 Connector
JUSB3: USB 3.2 Gen 1 Connector These connectors allow you to connect USB 3.2 Gen 1 5Gbps ports on the front panel. Power USB2.0+ USB3_RX_DN USB2.0- USB3_RX_DP Ground Ground USB3_TX_C_DP USB3_TX_C_DN USB3_TX_C_DN USB3_TX_C_DP Ground Ground USB3_RX_DP USB2.0- USB3_RX_DN USB2.0+ Power Ground No Pin ⚠... -
Page 46: Jusb1~2: Usb 2.0 Connectors
In order to recharge your iPad, iPhone and iPod through USB ports, please install ∙ MSI Center utility. JTPM1: TPM Module Connector This connector is for TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages. -
Page 47: Cpu_Fan1, Pump_Fan1, Sys_Fan1~6: Fan Connectors
CPU_FAN1, PUMP_FAN1, SYS_FAN1~6: Fan Connectors Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage. The auto mode fan connectors can automatically detect PWM and DC mode. -
Page 48: Jci1: Chassis Intrusion Connector
JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal Trigger the chassis (default) intrusion event Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2. -
Page 49: Bios_Sw1: Multi-Bios Switch
⚠ Important Do not use the Multi-BIOS switch when system is booting up. ∙ You can also use the MSI Center or Flash BIOS Button to flash BIOS. Please refer to ∙ BIOS section for details. Multi-BIOS LED Multi-BIOS LED indicates which BIOS ROM is in operation. -
Page 50: Jbat1: Clear Cmos (Reset Bios) Jumper
JBAT1: Clear CMOS (Reset BIOS) Jumper There is CMOS memory onboard that is external powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory. Keep Data Clear CMOS/ (default) -
Page 51: Jrgb1: Rgb Led Connector
(12V/G/R/B) with the maximum power rating of 3A (12V). Always turn off the power supply and unplug the power cord from the power outlet ∙ before installing or removing the RGB LED strip. Please use MSI’s software to control the extended LED strip. ∙ Overview of Components... -
Page 52: Jrainbow1~2: Addressable Rgb Led Connectors
(5V). In the case of 20% brightness, the connector supports up to 200 LEDs. ∙ Always turn off the power supply and unplug the power cord from the power outlet before installing or removing the RGB LED strip. Please use MSI’s software to control the extended LED strip. ∙ Overview of Components... -
Page 53: Jcorsair1: Corsair Connector
The JCORSAIR1 connector allows you to connect the CORSAIR Individually Addressable Lighting PRO RGB LED strips 5V or CORSAIR RGB fans with the CORSAIR fan hub. Once all items are connected properly, you can control the CORSAIR RGB LED strips and fans with MSI's software. JCORSAIR1 Data... -
Page 54: Onboard Leds
Onboard LEDs EZ Debug LED These LEDs indicate the debug status of the motherboard. CPU - indicates CPU is not detected or fail. DRAM - indicates DRAM is not detected or fail. VGA - indicates GPU is not detected or fail. BOOT - indicates the booting device is not detected or fail. -
Page 55: Led_Sw1: Ez Led Control
LED_SW1: EZ LED Control This switch is used to switch on/ off all the LEDs of motherboard. LED_OFF LED_ON (Default) LED_SW1 JPWRLED1: LED power input This connector is used by retailers to demonstrate onboard LED lights. JPWRLED1 - LED power input Debug Code LED The Debug Code LED displays progress and error codes during and after POST. -
Page 56: Hexadecimal Character Table
Hexadecimal Character Table Hexadecimal Debug Code 0 1 2 3 4 5 6 7 8 9 A B C D E F LED display Boot Phases Security (SEC) – initial low-level initialization Pre-EFI Initialization (PEI) – memory initialization Driver Execution Environment (DXE) – main hardware initialization Boot Device Selection (BDS) –... - Page 57 Memory initialization. Memory presence detection Memory initialization. Programming memory timing information Memory initialization. Configuring memory Memory initialization (other) Memory Installed CPU post-memory initialization is started CPU post-memory initialization. Cache initialization CPU post-memory initialization. Application Processor(s) (AP) initialization CPU post-memory initialization. Boot Strap Processor (BSP) selection CPU post-memory initialization.
- Page 58 64 - 67 CPU DXE initialization (CPU module specific) PCI host bridge initialization System Agent DXE initialization is started System Agent DXE SMM initialization is started 6B - 6F System Agent DXE initialization (System Agent module specific) PCH DXE initialization is started PCH DXE SMM initialization is started PCH devices initialization 73 - 77...
- Page 59 Setup Input Wait Ready To Boot event Legacy Boot event Exit Boot Services event Runtime Set Virtual Address MAP Begin Runtime Set Virtual Address MAP End Legacy Option ROM Initialization System Reset USB hot plug PCI bus hot plug Clean-up of NVRAM Configuration Reset (reset of NVRAM settings) B8 - BF Reserved for future AMI codes DXE Error Codes...
-
Page 60: Acpi States Codes
S3 Resume PPI not Found S3 Resume Boot Script Error S3 OS Wake Error EC - EF Reserved for future AMI error codes Recovery Progress Codes Recovery condition triggered by firmware (Auto recovery) Recovery condition triggered by user (Forced recovery) Recovery process started Recovery firmware image is found Recovery firmware image is loaded... -
Page 61: Installing Os, Drivers & Msi Center
MSI Center is an application that helps you easily optimize game settings and smoothly use content creation softwares. It also allows you to control and synchronize LED light effects on PCs and other MSI products. With MSI Center, you can customize ideal modes, monitor system performance, and adjust fan speed. -
Page 62: Nahimic 3
Sound Tracker. Installation and Update Nahimic 3 is included in the audio driver. If you need to install it or update it, please use the Driver Disc with your motherboard or download the driver from MSI’s official website. Audio Tab From this tab, you can access all of Nahimic 3’s audio effects, audio profiles and... -
Page 63: Microphone Tab
▪ Voices - it boosts (or removes) the speech in movies, video games and incoming communication from -12 to +12 dB. ▪ Bass - increases (or decreases) the energy in low frequencies from -12 to +12 ▪ Treble - increases (or decreases) the energy in high frequencies from -12 to +12 ∙... -
Page 64: Sound Tracker Tab
Sound Tracker Tab The Sound Tracker is an FPS oriented feature that provides a visual indication localizing the sources of the sounds while in a game. These are represented by dynamic segments pointing the direction of the sounds: the more opaque they are, the stronger the sounds are. -
Page 65: Uefi Bios
UEFI BIOS MSI UEFI BIOS is compatible with UEFI (Unified Extensible Firmware Interface) architecture. The UEFI BIOS firmware infrastructure has many new functions and advantages that traditional BIOS cannot achieve. It will fully support future PCs and devices that comply with UEFI firmware architecture. -
Page 66: Bios Setup
* When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice. BIOS User Guide If you’d like to know more instructions on setting up the BIOS, please refer to http://download.msi.com/manual/mb/Intel500BIOS.pdf or scan the QR code to access. UEFI BIOS... -
Page 67: Resetting Bios
Updating BIOS Updating BIOS with M-FLASH Before updating: Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash drive. To update BIOS: 1. Switch to the target BIOS ROM with Multi-BIOS switch. - Page 68 1. Please download the latest BIOS file that matches your motherboard model from the MSI® website. 2. Rename the BIOS file to MSI.ROM, and save it to the root of your USB flash drive. 3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU and memory.)
-
Page 69: Raid Configuration
All the information/ volumes/ pictures listed in your system might differ from the illustrations in this appendix. Intel RAID User Guide If you’d like to know more instructions on how to set up Intel RAID, please refer to http://download.msi.com/manual/mb/IntelRAID.pdf or scan the QR code to access. RAID Configuration... -
Page 70: Intel® Optane™ Memory Configuration
Optane™ memory, please note that it requires Windows 10 64-bit operating system. Intel® Optane™ Memory User Guide If you’d like to know more instructions on how to enable or remove Intel® Optane™ Memory, please refer to http://download.msi.com/manual/mb/Optane.pdf or scan the QR code to access. ⚠ WARNING After you enable Intel®... -
Page 71: Troubleshooting
Troubleshooting Lost BIOS password Before sending the motherboard for RMA repair, try to go over troubleshooting ∙ Clear the CMOS, but that will cause guide first to see if your got similar you to lose all customized settings in the symptoms as mentioned below. - Page 72 제조년월: 2021년 products. R-R-MSI-10-7D04 제조자 및 제조국가: MSI/중국 y Visit the MSI website and locate a nearby distributor y MEG Z590 ACE GOLD EDITION for further recycling information. 상호: (주)엠에스아이코리아 y Users may also reach us at gpcontdev@msi.com for 제품명: 메인보드...
- Page 73 MSI will comply with the product take estos residuos. back requirements at the end of life of MSI-branded NEDERLANDS products that are sold into the EU.
- Page 74 Products designed to be operated del suo ciclo di vita. MSI si adeguerà a tale Direttiva at closer proximities, such as tablet computers, ritirando tutti i prodotti marchiati MSI che sono stati comply with applicable EU requirements in typical venduti all’interno dell’Unione Europea alla fine del...
- Page 75 Copyright © 2020 All rights reserved. contact your place of purchase or local distributor. The MSI logo used is a registered trademark of Alternatively, please try the following help resources Micro-Star Int’l Co., Ltd. All other marks and names for further guidance.