Page 3
Quick Start Thank you for purchasing the MSI® motherboard. This Quick Start section provides demonstration diagrams about how to install your computer. Some of the installations also provide video demonstrations. Please link to the URL to watch it with the web browser on your phone or tablet.
Page 4
Installing a Processor/ CPUの取り付け/ 프로세서 설치하기/ 安裝 處理器/ 安装处理器 Youtube ⚽ https://youtu.be/KMf9oIDsGes 优酷 ⚽ https://v.youku.com/v_show/id_ XNTE5NDQwNDY2NA==.html...
Page 6
Connecting the Front Panel Header/ フロントパネルヘッダーの 接続/ 전면 패널 커넥터 연결하기/ 連接前置面板針腳/ 连接前置面 板接头 Youtube 优酷 ⚽ ⚽ http://v.youku.com/v_show/id_XNjcyMTczMzM2.html http://youtu.be/DPELIdVNZUI Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch JFP1...
Page 7
Installing the Motherboard/ マザーボードの取り付け/ 메인보드 설치하기/ 安裝主機板/ 安装主板 Youtube ⚽ https://youtu.be/wWI6Qt51Wnc 优酷 ⚽ https://v.youku.com/v_show/id_ XNDUwMDUyNTkwOA==.html Torque: 3 kgf·cm* *3 kgf·cm = 0.3 N·m = 2.6 lbf·in ⚠ Important Before installing the motherboard into the case, please refer to the M.2 section in this manual to remove the M.2 SHIELD FROZR heatsinks first.
Page 8
Connecting the Power Connectors/ 電源コネクターの接続/ 전원 커넥터 연결하기/ 插上電源接頭/ 连接电源接头 Youtube 优酷 ⚽ ⚽ http://youtu.be/gkDYyR_83I4 http://v.youku.com/v_show/id_XNDkzODU0MDQw.html ATX_PWR1 CPU_PWR1 CPU_PWR1~2 VIII...
Page 9
Installing SATA Drives/ SATAドライブの取り付け/ SATA 드라이브 설치하기/ 安裝 SATA 磁碟機/ 安装 SATA 设备 Youtube ⚽ http://youtu.be/RZsMpqxythc 优酷 ⚽ http://v.youku.com/v_show/ id_XNDkzODU5MTky.html...
Page 10
Installing a Graphics Card/ グラフィックスカードの取り付け/ 그래픽 카드 설치하기 / 安裝顯示卡/ 安装显卡 Youtube ⚽ http://youtu.be/mG0GZpr9w_A 优酷 ⚽ http://v.youku.com/v_show/ id_XNDkyOTc3MzQ4.html...
Page 11
Full armor kit/ フルアーマーキット/ 풀 아머 키트/ 全套裝甲/ 全套 盔甲...
Page 12
Connecting Peripheral Devices/ 周辺機器の接続/ 주변 장치 연결하기/ 連接周邊設備/ 连接外围设备...
Safety Information ∙ The components included in this package are prone to damage from electrostatic discharge (ESD). Please adhere to the following instructions to ensure successful computer assembly. ∙ Ensure that all components are securely connected. Loose connections may cause the computer to not recognize a component or fail to start.
Specifications ∙ Supports 12th Gen Intel® Core™, Pentium® Gold and Celeron® Processors* ∙ Processor socket LGA1700 * Please go to www.msi.com to get the newest support status as new processors are released. Intel® Z690 Chipset Chipset ∙ 4x DDR5 memory slots, supporting up to 128GB* ∙...
Page 20
Continued from previous page Intel® JHL8540 Thunderbolt™ 4 Controller ∙ 2x Thunderbolt™ 4 (USB-C) ports on the back panel ▪ Support up to 40 Gbps transfer rate with Thunderbolt devices ▪ Support up to 20 Gbps transfer rate with USB4 devices ▪...
Page 22
Continued from previous page ∙ Supports RAID 0, RAID 1, RAID 5 and RAID 10 for SATA storage devices* RAID ∙ Supports RAID 0, RAID 1, RAID 5 and RAID 10 for M.2 NVMe storage devices * SATAA & SATAB do not support RAID function. 1x Aquantia®...
Page 23
Continued from previous page ∙ 1x 24-pin ATX main power connector ∙ 2x 8-pin ATX 12V power connectors ∙ 6x SATA 6Gb/s connectors ∙ 6x M.2 slots (M-Key) ∙ 2x USB 3.2 Gen 2x2 20Gbps Type-C ports ∙ 2x USB 3.2 Gen 1 5Gbps connectors (supports additional 4 USB 3.2 Gen 1 5Gbps ports) ∙...
Page 24
∙ Drivers ∙ MSI Center ∙ Intel Extreme Tuning Utility ∙ Nahimic Software ∙ MSI APP Player (BlueStacks) ∙ Open Broadcaster Software (OBS) ∙ CPU-Z MSI GAMING ∙ Google Chrome™, Google Toolbar, Google Drive ∙ Norton™ Internet Security Solution Continued on next page...
Page 25
Continued from previous page ∙ MSI Sound Tune ∙ Gaming Mode ∙ Smart Priority ∙ Game Highlights ∙ LAN Manager ∙ Mystic Light ∙ Ambient Devices ∙ Frozr AI Cooling MSI Center Features ∙ User Scenario ∙ True Color ∙ Live Update ∙...
Page 26
Continued from previous page ∙ Cooling ▪ M.2 Shield Frozr ▪ 7W/mK MOSFET thermal pad ▪ Choke thermal pad ▪ Pump Fan Control ▪ Smart Fan Control ∙ LED ▪ Mystic Light ▪ Mystic Light Extension (RAINBOW/CORSAIR/RGB) ▪ Mystic Light SYNC ▪...
Package contents Please check the contents of your motherboard package. It should contain: Motherboard MEG Z690 GODLIKE Quick installation guide Documentation DIY Stands Set Quick Guide Application USB drive with drivers & utilities SATA 6Gb/s cables LED JRGB Y cable...
Realtek Audio Console After Realtek Audio Console is installed. You can use it to change sound settings to get better sound experience. Application Enhancement Device Selection Main Volume Connector Settings Jack Status ∙ Device Selection - allows you to select a audio output source to change the related options.
Page 31
Audio jacks to headphone and microphone diagram Audio jacks to stereo speakers diagram AUDIO INPUT Audio jacks to 7.1-channel speakers diagram AUDIO INPUT Rear Front Side Center/ Subwoofer Rear I/O Panel...
Installing Antennas 1. Combine the antenna with the base. 2. Screw two antenna cables tight to the WiFi antenna connectors as shown. 3. Place the antenna as high as possible. Rear I/O Panel...
Connecting Thunderbolt Devices via Daisy-chain Daisy-chain is a method of connecting multiple devices to a PC with only one output terminal. Daisy-chain allows you to connect multiple thunderbolt devices to a single thunderbolt port on the back panel. You can also daisy chain monitor by connecting graphics card to the Mini DisplayPort Input port on the back panel.
∙ the CPU. ∙ Please retain the CPU protective cap after installing the processor. MSI will deal with Return Merchandise Authorization (RMA) requests if only the motherboard comes with the protective cap on the CPU socket. When installing a CPU, always remember to install a CPU heatsink. A CPU heatsink ∙...
It is recommended to use a more efficient memory cooling system for full DIMMs ∙ installation or overclocking. The stability and compatibility of installed memory module depend on installed CPU ∙ and devices when overclocking. ∙ Please refer www.msi.com for more information on compatible memory. Overview of Components...
PCI_E3: PCIe 4.0 x4 (From Z690 chipset) ⚠ Important If you install a large and heavy graphics card, you need to use a tool such as MSI ∙ Gaming Series Graphics Card Bolster to support its weight to prevent deformation of the slot.
M2_1~6: M.2 Slots (Key M) ⚠ Important ∙ Intel® RST only supports PCIe M.2 SSD with UEFI ROM. M2_1 M2_2, M2_4, M2_5 and M2_6 support Intel ∙ M2_2 Optane Memory. M2_3 M2_6 M2_4 M2_5 ⚠ Important M2_3 will be unavailable when installing device in the PCI_E2 slot. ∙...
Page 39
5. Remove the protective films from the M.2 thermal pads on the M.2 plate. 6. Remove or exchange the screws according to your SSD length. Skip this step, if you install 2280 SSD. 2260 SSD 22110 SSD 7. Insert your M.2 SSD into the M.2 slot at a 30-degree angle. 8.
Page 40
9. Put the M2_3 SHIELD FROZR heatsink back in place and secure it. 10. Put the chipset heatsink back in place and secure it. 11. Put the M2_1 SHIELD FROZR heatsink back in place and secure it. chipset M2_1 M2_3 M2_2 &...
Page 41
5. Remove the protective films from the M.2 thermal pads on the M.2 plate. 6. If you install 2260 SSD, remove the screw from the M.2 plate and then install supplied EZ M.2 Clip kit on the M.2 plate. Skip this step if you install 2280 SSD. 2260 SSD 7.
Page 42
9. Put the M2_6 SHIELD FROZR heatsink back in place and secure it. 10. Put the M2_2 SHIELD FROZR heatsink back in place and secure it. 11. Put the chipset heatsink back in place and secure it. chipset M2_6 M2_2 M2_4 &...
Page 43
4. Remove the protective films from the M.2 thermal pads on the M.2 plate. 5. If there is a screw installed on the M.2 plate, remove it first; otherwise, please skip this step. 6. Secure the supplied M.2 standoff according to your M.2 SSD length. Standoff Overview of Components...
Page 44
7. Insert your M.2 SSD into the M.2 slot at a 30-degree angle. 8. Secure the M.2 SSD in place with the supplied M.2 8.5H screw. 8.5H screw 30º 30º 9. Put the M2_4~5 SHIELD FROZR heatsink back in place and secure it. 10.
SATA5~8 & SATAA~B: SATA 6Gb/s Connectors These connectors are SATA 6Gb/s interface ports. Each connector can connect to one SATA device. SATAB SATAA SATA6 SATA5 SATA8 SATA7 ⚠ Important Please do not fold the SATA cable at a 90-degree angle. Data loss may result during ∙...
JFP1, JFP2: Front Panel Connectors These connectors connect to the switches and LEDs on the front panel. Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED -...
JSLOW1: Slow Mode Booting Jumper This jumper is used for LN2 cooling solution, that provides the extreme overclocking conditions, to boot at a stable processor frequency and to prevent the system from crashing. Normal Enabled (Default) (Please enable this jumper during BIOS POST.) JLN1~2: Low Temperature Booting Jumper This jumper is used for liquid nitrogen cooling system to boot at an extreme low...
T_SEN1~2: Thermal Sensor Connectors These connectors allow you to connect the thermistor cable and use it to monitor the temperature of the detection point. Thermistor cable Sense V-Check Points Lite These voltage checkpoints are used to measure the current system voltages. A multimeter (not included) will be required to check voltages.
JDASH1 : Tuning Controller connector This connector is used to connect an optional Tuning Controller module. No Pin MCU_SMB_SCL_M MCU_SMB_SDA_M VCC5 Ground PSIN#_R FP_RST#_R OC_RETRY# OC_FS BLK+ BLK- CLRCMOS_EN Connecting the JDASH1 and Tuning Controller module OC button+ OC Fail Save Debug Code LED Reset Clear CMOS...
Page 52
Tuning Controller module magnet Tuning controller module has build in some magnets on both sides that will be convenient for you to stick it to the chassis. However, we provide extra four magnets for sticking inside the back cover of module. Please follow the instructions below to stick the magnets.
JUSB1~2: USB 3.2 Gen 2x2 Type-C Connectors These connectors allow you to connect USB 3.2 Gen 2x2 20Gbps Type-C connector on the front panel. The connector possesses a foolproof design. When you connect the cable, be sure to connect it with the corresponding orientation. USB Type-C Cable JUSB1/ 2 USB Type-C port on...
∙ In order to recharge your iPad,iPhone and iPod through USB ports, please install MSI® Center utility. JTPM1: TPM Module Connector This connector is for TPM (Trusted Platform Module). Please refer to the TPM security platform manual for more details and usages.
CPU_FAN1, PUMP_FAN1, SYS_FAN1~8: Fan Connectors Fan connectors can be classified as PWM (Pulse Width Modulation) Mode or DC Mode. PWM Mode fan connectors provide constant 12V output and adjust fan speed with speed control signal. DC Mode fan connectors control fan speed by changing voltage. The auto mode fan connectors can automatically detect PWM and DC mode.
JCI1: Chassis Intrusion Connector This connector allows you to connect the chassis intrusion switch cable. Normal Trigger the chassis (default) intrusion event Using chassis intrusion detector 1. Connect the JCI1 connector to the chassis intrusion switch/ sensor on the chassis. 2.
JBAT1: Clear CMOS (Reset BIOS) Jumper There is CMOS memory onboard that is externally powered from a battery located on the motherboard to save system configuration data. If you want to clear the system configuration, set the jumpers to clear the CMOS memory. Keep Data Clear CMOS/ (default)
(12V/G/R/B) with the maximum power rating of 3A (12V). Always turn off the power supply and unplug the power cord from the power outlet ∙ before installing or removing the RGB LED strip. Please use MSI’s software to control the extended LED strip. ∙ Overview of Components...
3A (5V). In the case of 20% brightness, the connector supports up to 200 LEDs. Always turn off the power supply and unplug the power cord from the power outlet ∙ before installing or removing the RGB LED strip. ∙ Please use MSI’s software to control the extended LED strip. Overview of Components...
The JCORSAIR1 connector allows you to connect the CORSAIR Individually Addressable Lighting PRO RGB LED strips 5V or CORSAIR RGB fans with the CORSAIR fan hub. Once all items are connected properly, you can control the CORSAIR RGB LED strips and fans with MSI's software. Data Ground...
CPU speed, BIOS flash status and error message. You also can power on/ off the system and launch the MSI Center, Youtube, music APP, browser of the system by touching the M-VISION Dashboard. You can use MSI’s software to configure and customize the M-VISION Dashboard Advanced mode and even upload a .gif/ .bmp/...
Page 62
M-VISION Dashboard Basic mode Debug Code LED Tuning Controller Countdown Timer Temperature display Humidity display Debug Code LED It displays CPU core temperature (default), progress and error codes during and after POST. Please refer to the Debug Code LED table in this manual for details. Tuning Controller Tuning controller helps you to monitor, control and overclock the motherboard more easily.
Page 63
MSI Center. If not, please download and install the MSI Center first. You can use the MSI Center to configure and customize the advanced mode of the M-VISION dashboard and even upload the pictures or animation files. The M-VISION dashboard can be used to display the system information and status.
M-VISION Dashboard Status Table System Status M-VISION Dashboard System Status M-VISION Dashboard Hardware Power On Monitor page CPU is not System Clock detected or fail page S4/S5 (Suspend Live weather to Disk/ Shutdown) 800*480px.gif/ Flash BIOS User profile bmp/ jpg/ png/ (Update) Overview of Components...
Onboard LEDs EZ Debug LED These LEDs indicate the debug status of the motherboard. BOOT - indicates the booting device is not detected or fail. VGA - indicates GPU is not detected or fail. DDR - indicates DRAM is not detected or fail. CPU - indicates CPU is not detected or fail.
Debug Code LED The Debug Code LED displays CPU core temperature (default), progress and error codes during and after POST. Refer to the Debug Code LED table for details. Debug Code LED Hexadecimal Character Table Hexadecimal Debug Code 0 1 2 3 4 5 6 7 8 9 A B C D E F LED display Boot Phases Security (SEC) –...
Page 67
Microcode not loaded PEI Progress Codes PEI Core is started Pre-memory CPU initialization is started 12 - 14 Pre-memory CPU initialization (CPU module specific) Pre-memory System Agent initialization is started 16 - 18 Pre-Memory System Agent initialization (System Agent module specific) Pre-memory PCH initialization is started 1A - 1C Pre-memory PCH initialization (PCH module specific) Memory initialization.
Page 68
CPU self test failed or possible CPU cache error CPU micro-code is not found or micro-code update is failed Internal CPU error Reset PPI is not available 5C - 5F Reserved for future AMI error codes DXE Progress Codes DXE Core is started NVRAM initialization Installation of the PCH Runtime Services CPU DXE initialization is started...
Page 69
9E -9F Reserved for future AMI codes IDE initialization is started IDE Reset IDE Detect IDE Enable SCSI initialization is started SCSI Reset SCSI Detect SCSI Enable Setup Verifying Password Start of Setup Setup Input Wait Ready To Boot event Legacy Boot event Exit Boot Services event Runtime Set Virtual Address MAP Begin...
Page 70
Boot Option is failed (StartImage returned error) Flash update is failed Reset protocol is not available S3 Resume Progress Codes S3 Resume is stared (S3 Resume PPI is called by the DXE IPL) S3 Boot Script execution Video repost OS S3 wake vector call E4 - E7 Reserved for future AMI progress codes S3 Resume Error Codes...
Page 71
System is waking up from the S1 sleep state System is waking up from the S2 sleep state System is waking up from the S3 sleep state System is waking up from the S4 sleep state System has transitioned into ACPI mode. Interrupt controller is in PIC mode.
MSI Center is an application that helps you easily optimize game settings and smoothly use content creation softwares. It also allows you to control and synchronize LED light effects on PCs and other MSI products. With MSI Center, you can customize ideal modes, monitor system performance, and adjust fan speed.
UEFI has many new functions and advantages that traditional BIOS cannot achieve, and it will completely replace BIOS in the future. The MSI UEFI BIOS uses UEFI as the default boot mode to take full advantage of the new chipset’s capabilities.
* When you press F10, a confirmation window appears and it provides the modification information. Select between Yes or No to confirm your choice. BIOS User Guide If you’d like to know more instructions on setting up the BIOS, please refer to http://download.msi.com/manual/mb/Intel600BIOS.pdf or scan the QR code to access. UEFI BIOS...
Updating BIOS Updating BIOS with M-FLASH Before updating: Please download the latest BIOS file that matches your motherboard model from MSI website. And then save the BIOS file into the USB flash drive. Updating BIOS: 1. Switch to the target BIOS ROM by Multi-BIOS switch. Please skip this step if your motherboard doesn't has this switch.
Page 76
1. Please download the latest BIOS file that matches your motherboard model from the MSI® website. 2. Rename the BIOS file to MSI.ROM, and save it to the root of the USB storage device. 3. Connect the power supply to CPU_PWR1 and ATX_PWR1. (No need to install CPU and memory.)
Page 110
JFP1 JFP2: フロントパネルコネクター これらのコネクターにはフロン トパネルのスイッチとLEDを接続します。 Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch...
Page 115
JUSB1~2: USB 3.2 Gen 2x2 Type-Cコネクター これらのコネクターにはフロン トパネルのUSB 3.2 Gen 2x2 20Gbps Type-Cコネクターを 接続します。 このコネクターは確実なデザインを持っています。 ケーブルを接続すると、 対応 方向で接続することを確認して ください。 USB Type-Cケー JUSB1/ 2 ブル フロン トパネルの USB Type-Cポート JUSB3~4: USB 3.2 Gen 1コネクター これらのコネクターにはフロン トパネルのUSB 3.2 Gen 1 5Gbpsポートを接続します。 Power USB2.0+ USB3_RX_DN USB2.0-...
Page 116
No Pin ⚠ 注意 VCCピンとグランドピンは必ず接続して ください。 正し く接続されていない場合、 機器が損 ∙ 傷するおそれがあります。 ∙ これらのUSBポートでiPad、 iPhoneとiPodを再充電するには、 MSI® Center ユーティ リテ ィをインストールして ください。 JTPM1: TPMモジュールコネクター このコネクターはTPM (Trusted Platform Module)を接続します。 詳細についてはTPMセキ ュリティ プラッ トホームマニュアルを参照して下さい。 SPI Power SPI Chip Select Master In Slave Out (SPI Data)
Page 139
목차 안전 지침 ....................... 3 충돌 방지 알림 ......................4 사양 ......................5 JCORSAIR1 커넥터 사양 ..................13 제품 내용물 ....................14 후면 I/O 패널 ....................15 LAN 포트 LED 상태 표시 ..................15 오디오 포트 구성 도표 ..................... 15 Realtek 오디오...
Page 140
디버그 코드 LED 표 ....................52 SEC 진행 코드 ....................... 52 ACPI 상태 코드 ....................... 57 CPU 온도 ....................... 57 OS, 드라이버 & MSI 센터 설치하기 ..............58 Windows 10/ Windows 11 설치하기 ............... 58 드라이버 설치하기 ....................58 MSI 센터 ........................ 58 UEFI BIOS ....................
안전 지침 ∙ 이 패키지에 포함된 부품은 정전기 방전(ESD)에 의해 파손될 우려가 있으므로 다음의 설명에 따라 컴퓨터를 조립하십시오. ∙ 모든 부품이 제대로 연결되었는지 확인하십시오. 제대로 연결되지 않을 경우, 컴퓨터가 부품을 인식하지 못하거나 컴퓨터를 켤 수가 없게 됩니다. ∙ 부품의 예리한 부분에 손을 다칠 수 있으므로 메인보드 취급시 가장자리 부분을 잡으십시오. ∙...
충돌 방지 알림 각 나사 구멍 주위에 보호 페인트가 인쇄되어 있어 부품이 긁히는 것을 방지합니다. 안전 지침...
Page 143
사양 ∙ 12세대 인텔® 코어™, 펜티엄® 골드 및 셀레론® 프로세서 지원* ∙ 소켓 LGA1700 프로세서 * 출시된 새 프로세서의 최신 지원 상태를 확인하려면 www.msi.com을 방문하십시오. 인텔 ® Z690 칩셋 칩셋 ∙ 4x DDR5 메모리 슬롯, 최대 128GB* 지원 ∙ 1R 4800 MHz (by JEDEC & POR) 지원...
Page 144
이전 페이지로부터 계속 인텔® JHL8540 썬더볼트™ 4 컨트롤러 ∙ 2x 썬더볼트™ 4 (USB-C) 후면 패널에 포트 ▪ 썬더볼트 장치로 최대 40 Gbps 전송률 지원 ▪ USB4 장치로 최대 20Gbps 전송률 지원 ▪ USB 3.2 장치로 최대 10Gbps 전송률 지원 썬더볼트 4 ▪...
Page 145
이전 페이지로부터 계속 ∙ 6x SATA 6Gb/s 포트 ▪ SATA5 ~8 (Z690 칩셋)* ▪ SATAA~B (Asmedia 1061) ∙ 6x M.2 슬롯 (Key M) ▪ M2_1 슬롯(CPU) ▫ PCIe 4.0 x4 지원 ▫ 2260/ 2280/ 22110 저장 장치 지원 ▪ M2_2 슬롯(Z690 칩셋) ▫...
Page 146
이전 페이지로부터 계속 ∙ RAID 0, RAID 1, RAID 5 및 RAID 10 (SATA 저장 장치 ) 지원 * ∙ RAID 0, RAID 1, RAID 5 및 RAID 10 (M.2 NVMe 저장 장치) RAID 지원 * SATAA 및 SATAB 는 RAID 기능을 지원하지 않습니다. 1x Aquantia®...
Page 147
이전 페이지로부터 계속 ∙ 1x 24핀 ATX 메인 전원 커넥터 ∙ 2x 8핀 ATX 12V 전원 커넥터 ∙ 6x SATA 6Gb/s 커넥터 ∙ 6x M.2 슬롯(M-Key) ∙ 2x USB 3.2 Gen 2x2 20Gbps Type-C 포트 ∙ 2x USB 3.2 Gen 1 5Gbps 커넥터(외 4 USB 3.2 Gen 1 5Gbps 포트...
Page 148
∙ 드라이버 ∙ MSI 센터 ∙ 인텔 익스트림 튜닝 유틸리티 ∙ 나히믹 소프트웨어 ∙ MSI APP Player (BlueStacks) ∙ Open Broadcaster Software (OBS) ∙ CPU-Z MSI 게이밍 ∙ 구글 유틸리티 : 크롬™, 툴바, 드라이브 ∙ 노턴™ 인터넷 시큐리티 솔루션 다음 페이지에서 계속...
Page 149
이전 페이지로부터 계속 ∙ MSI 사운드 튠 ∙ 게이밍 모드 ∙ 스마트 우선순위 ∙ 게임 하이라이트 ∙ LAN 매니저 ∙ 미스틱 라이트 ∙ 엠비언트 장치 ∙ 프로져 AI 쿨링 MSI 센터 기능 ∙ 사용자 시나리오 ∙ True Color ∙ 라이브 업데이트...
Page 150
이전 페이지로부터 계속 ∙ 쿨링 ▪ M.2 쉴드 프로져 ▪ 7W/mK MOSFET 열 패드 ▪ Choke 열 패드 ▪ 펌프 팬 컨트롤 ▪ 스마트 팬 컨트롤 ∙ LED ▪ 미스틱 라이트 ▪ 미스틱라이트익스텐션(RAINBOW/CORSAIR/RGB) ▪ 미스틱 라이트 싱크 ▪ 엠비언트 장치 지원 ▪...
제품 내용물 메인보드 패키지의 내용물을 확인하십시오. 다음 품목들이 패키지에 들어 있어야 합니다: 메인보드 MEG Z690 GODLIKE 빠른 설치 설명서 서류 DIY 스탠드 세트 빠른 설명서 애플리케이션 드라이버 & 유틸리티를 포함한 USB 드라이브 SATA 6Gb/s 케이블 LED JRGB Y 케이블 LED JCORSAIR 케이블...
후면 I/O 패널 Wi-Fi 안테나 커넥터 썬더볼트 4 플래쉬 BIOS 버튼 CMOS 클리어 (USB-C) 오디오 포트 점퍼 2.5 Gbps LAN 10 Gbps LAN 옵티컬 플래쉬 M-VISION 대쉬보드 포트 S/PDIF- 출력 BIOS 버튼 USB 3.2 Gen 2 미니 디스플레이포트 입력 10Gbps Type-A ( 썬더볼트...
Realtek 오디오 콘솔 Realtek 오디오 콘솔을 설치한 후 사운드 설정을 변경하여 더 나은 사운드를 경험할 수 있습니다. 애플리케이션 강화 장치 선택 메인 볼륨 커넥터 설정 잭 설정 ∙ 장치 선택 - 오디오 출력 소스를 선택하여 관련 옵션을 변경합니다. 체크 표시된 장치가 기본 장치입니다.
Page 155
헤드폰 및 마이크용 오디오 잭 도표 스테레오 스피커용 오디오 잭 도표 AUDIO INPUT 7.1-채널 스피커용 오디오 잭 도표 AUDIO INPUT Rear Front Side Center/ Subwoofer 제품 내용물...
Daisy-chain통한 썬더볼트 장치 연결 데이지 체인은 하나의 출력 단자로 여러 장치를 PC에 연결하는 방법입니다. Daisy-chain을 사용하면 여러 썬더볼트 장치를 후면 패널의 단일 썬더볼트 포트에 연결할 수 있습니다. 그래픽 카드를 후면 패널의 미니 디스플레이포트 입력 포트에 연결하여 모니터를 daisy chain 으로 연결할 수도 있습니다. USB 장치를...
∙ 프로세서를 설치한 후, CPU 보호 캡을 보관하시기 바랍니다. 반품시 메인보드와 CPU 소켓 ∙ 보호 캡이 함께 제공되어야만 MSI에서 반품(RMA) 요청 처리를 진행할 수 있습니다. ∙ CPU 설치시, CPU 히트싱크를 반드시 설치하세요. CPU 히트싱크는 과열을 방지하고 시스템 성능을 유지하는데 꼭 필요합니다.
풀 DIMM 설치 또는 오버클로킹을 위해 보다 효율적으로 메모리 냉각 시스템을 사용할 것을 ∙ 권장합니다. 오버클로킹시의 안정성과 설치된 메모리 모듈의 호환성은 설치된 CPU 및 장치에 따라 ∙ 달라집니다. ∙ 호환 가능한 메모리에 대한 자세한 정보는 www.msi.com을 방문하여 알아보시기 바랍니다. 구성품 개요...
중요사항 크고 무거운 그래픽 카드를 설치할 경우, 그래픽 카드를 안전하게 지지하여 슬롯의 변형을 ∙ 방지하기 위해 MSI 그래픽 카드 지지대와 같은 장치를 사용하시면 더욱 안전합니다. ∙ 하나의 PCIe x16 확장 카드를 설치하여 최적의 효과를 원하신다면 PCI_E1 슬롯을 사용할 것을 추천합니다.
M2_1~6: M.2 슬롯 (Key M) ⚠ 중요사항 ∙ 인텔® RST는 PCIe M.2 SSD UEFI ROM만 지원합니다 M2_1 인텔® Optane™ Memory Ready (M2_2, M2_4, ∙ M2_2 M2_5 및M2_6) M2_3 M2_6 M2_4 M2_5 ⚠ 중요사항 PCI_E2 슬롯에 장치가 설치된 경우 M2_3 를 사용할 수 없습니다. ∙...
Page 163
5. M.2 플레이트의 M.2 열 패드에서 보호 필름을 제거합니다. 6. SSD 길이에 따라 나사를 제거하거나 교체하십시오. 2280 SSD를 설치한 경우 이 단계를 건너뜁니다. 2260 SSD 22110 SSD 7. M.2 SSD를 30도 각도로 M.2 슬롯에 삽입합니다. 8. EZ M.2 클립을 돌려 M.2 SSD를 고정합니다. 30º...
Page 164
9. M2_3 쉴드 FROZR 히트싱크을 제자리에 다시 놓고 고정합니다. 10. 칩셋 히트싱크을 제자리에 놓고 고정합니다. 11. M2_1 쉴드 FROZR 히트싱크을 제자리에 다시 놓고 고정합니다. 칩셋 M2_1 M2_3 M2_2 & M2_6 슬롯 설치하기 1. 칩셋 히트싱크의 나사를 풀어서 제거합니다. 2. M2_2 쉴드 FROZR 히트싱크의 나사를 풀고 히트싱크을 제거합니다. 3.
Page 165
5. M.2 플레이트의 M.2 열 패드에서 보호 필름을 제거합니다. 6. 2260 SSD를 설치하는 경우 M.2 플레이트에서 나사를 제거한 다음 M.2 플레이트에 제공된 EZ M.2 클립 키트를 설치합니다. 2280 SSD를 설치한 경우 이 단계를 건너뜁니다. 2260 SSD 7. M.2 SSD를 30도 각도로 M.2 슬롯에 삽입합니다. 8.
Page 167
4. M.2 플레이트의 M.2 열 패드에서 보호 필름을 제거합니다. 5. M.2 플레이트에 나사가 설치되어 있으면 먼저 나사를 제거하십시오. 그렇지 않으면 이 단계를 건너뛰십시오. 6. M.2 SSD 길이에 따라 제공된 M.2 스탠드오프를 고정합니다. 스탠드오프 구성품 개요...
SATA5~8 & SATAA~B: SATA 6Gb/s 커넥터 이 커넥터는 SATA 6Gb/s 인터페이스 포트입니다. 각 커넥터에 하나의 SATA 장치를 연결할 수 있습니다. SATAB SATAA SATA6 SATA5 SATA8 SATA7 ⚠ 중요사항 SATA 케이블을 90도로 꺽지 마십시오. 그럴 경우, 전송 중 데이터가 손상될 수 있습니다. ∙...
전원 커넥터 이 커넥터를 사용하여 ATX 전원 공급 장치를 연결할 수 있습니다. CPU_PWR1~2 Ground +12V Ground +12V Ground +12V Ground +12V +3.3V +3.3V +3.3V -12V Ground Ground PS-ON# Ground Ground Ground ATX_PWR1 Ground Ground PWR OK 5VSB +12V +12V +3.3V Ground ⚠...
JFP1, JFP2: 전면 패널 커넥터 이 커넥터를 사용하여 전면 패널에 있는 스위치 및 LED를 연결할 수 있습니다. Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + 전원 LED 전원 스위치 JFP1 Reserved HDD LED 리셋 스위치 HDD LED + Power LED + HDD LED - Power LED -...
JSLOW1: 슬로우 모드 부팅 점퍼 이 점퍼는 LN2 쿨링을 위한 솔루션으로서 익스트림 오버클럭 상태의 프로세서를 안정된 클럭으로 유지하게 해주며 시스템 충돌을 막을 수 있습니다. 표준 상태 활성화 (기본 설정) (BIOS POST 동안, 이 기능을 “사용”으로 설정) JLN1~2: 저온 부팅 점퍼 이...
T_SEN1~2: 열 센서 커넥터 이 커넥터에 서미스터 케이블을 연결하여 감지 포인트의 온도를 모니터링할 수 있습니다. 서미스터 케이블 Sense V-체크 포인트 라이트 본 전압 체크 포인트는 현재 시스템 전압을 측정하는데 사용됩니다. 전압을 확인하려면 멀티미터(제품 내 미포함)가 필요합니다. 전압을 측정하기 위해서는, GND (접지 그라운드) 와...
JDASH1 : 튜닝 컨트롤러 커넥터 이 커넥터를 사용하여 옵션인 튜닝 컨트롤러 모듈을 연결할 수 있습니다. No Pin MCU_SMB_SCL_M MCU_SMB_SDA_M VCC5 Ground PSIN#_R FP_RST#_R OC_RETRY# OC_FS BLK+ BLK- CLRCMOS_EN JDASH1 및 튜닝 컨트롤러 모듈 연결 OC 버튼+ OC Fail Save 디버그 코드 LED 리셋...
Page 176
튜닝 컨트롤러 모듈 자석 튜닝 컨트롤러 모듈에는 양쪽에 자석이 내장되어있어 섀시에 부착하는 데 편리합니다. 단, 모듈 후면 커버 내부에 부착 할 수있는 자석 4개를 추가로 제공합니다. 자석을 붙이려면 아래 지침을 따르십시오. 1. 뒷면 커버의 나사를 풀어줍니다. 2. 뒷면 커버를 열고 뒤집습니다. 3.
JUSB1~2: USB 3.2 Gen 2x2 Type-C 커넥터 이 커넥터를 사용하여 전면 패널의 USB 3.2 Gen 2x2 20Gbps Type-C 커넥터를 연결할 수 있습니다. 이 커넥터는 풀 프루프(foolproof )로 작동하도록 디자인되었으며 케이블 연결시 정확한 방향으로 연결하시기 바랍니다. USB Type-C JUSB1/ 2 케이블 USB Type-C 후면...
No Pin 중요사항 VCC 및 그라운드 핀을 정확히 연결하여야 손상을 방지할 수 있습니다. ∙ USB 포트를 통하여 iPad,iPhone 및 iPod를 충전하려면 MSI 센터 유틸리티를 설치하시기 ∙ 바랍니다. JTPM1: TPM 모듈 커넥터 이 커넥터는 TPM (Trusted Platform Module) 모듈에 연결됩니다. 자세한 내용과 사용방법은...
CPU_FAN1, PUMP_FAN1, SYS_FAN1~8: 팬 커넥터 팬 커넥터는 PWM (Pulse Width Modulation) 모드와 DC 모드로 분류될 수 있습니다. PWM 모드 팬 커넥터는 12V의 일정한 출력을 제공하고 속도 제어 신호에 따라 팬의 회전 속도를 조정합니다. DC 모드 팬 커넥터는 전압의 변화에 따라 팬의 회전 속도를 제어합니다. 자동 모드 팬...
JBAT1: CMOS (Reset BIOS) 클리어 점퍼 보드에 시스템 구성 데이터를 유지하기 위해 외부 배터리로부터 전원을 공급 받는 CMOS 메모리가 있습니다. 시스템 구성을 지우려면 점퍼를 아래와 같이 설정하여 CMOS 메모리를 지우세요. 데이터 유지 CMOS 클리어/ (기본 설정) BIOS 리셋 기본 값으로 BIOS 리셋하기 1.
JRGB 커넥터는 최대 3A (12V) 정격 전력에서 최대 2미터 연속 5050 RGB LED 스트립 (12V/G/R/B)을 지원합니다. RGB LED 스트립을 설치 또는 제거하기 전에 항상 전원 공급 장치의 전원을 끄고 전원 ∙ 코드를 콘센트에서 뽑아주세요. MSI 소프트웨어를 사용하여 확장된 LED 스트립을 조정하세요. ∙ 구성품 개요...
RGB LED 스트립(5V/Data/Ground)을 지원합니다. 밝기 20%의 경우에 커넥터는 최대 200 개의 LED를 지원합니다. ∙ RGB LED 스트립을 설치 또는 제거하기 전에 항상 전원 공급 장치의 전원을 끄고 전원 코드를 콘센트에서 뽑아주세요. ∙ MSI 소프트웨어를 사용하여 확장된 LED 스트립을 조정하세요. 구성품 개요...
Page 184
JCORSAIR1: CORSAIR 커넥터 JCORSAIR1 커넥터는 CORSAIR 개별 주소 지정가능한 라이팅 PRO RGB LED 스트립 5V 또는 CORSAIR RGB 팬을 CORSAIR 팬 허브와 연결할 수 있습니다. 모든 항목이 제대로 연결되면 CORSAIR RGB LED 스트립과 팬을 MSI 소프트웨어와 함께 조정할 수 있습니다. Data Ground CORSAIR RGB 팬...
M-VISION 대쉬보드를 사용하여 시스템 정보, CPU 온도, CPU 속도, BIOS 플래시 상태 및 오류 메시지를 표시할 수 있습니다. 또한 M-VISION 대쉬보드를 터치하여 시스템의 전원을 켜고 끌 수 있으며 MSI Center, Youtube, music APP, 시스템 브라우저를 실행할 수 있습니다. MSI의 소프트웨어를 사용하여 M-VISION 대쉬보드 고급 모드를 구성 및 사용자 정의하고 .gif/ .bmp/ .png/ .jpg 또는...
Page 186
M-VISION 대쉬보드 베이직 모드 디버그 코드 LED 튜닝 컨트롤러 카운트다운 타이머 온도 디스플레이 습도 디스플레이 디버그 코드 LED CPU 코어 온도 (기본값), 진행률 및 POST 도중과 이후의 오류 코드를 표시합니다. 자세한 내용은 이 매뉴얼의 디버그 코드 LED 표를 참조하십시오. 튜닝 컨트롤러 튜닝...
Page 187
M-VISION 대시보드 고급 모드를 사용하기 전에 MSI 센터를 설치했는지 확인하십시오. 그렇지 않은 경우 먼저 MSI Center를 다운로드하여 설치하십시오. MSI 센터를 사용하여 M-VISION 대시보드의 고급 모드를 구성 및 사용자 지정하고 사진이나 애니메이션 파일을 업로드할 수도 있습니다. M-VISION 대시보드는 시스템 정보 및 상태를...
M-VISION 대쉬보드 상태표 시스템 상태 M-VISION 대쉬보드 시스템 상태 M-VISION 대쉬보드 하드웨어 모니터 전원 켜기 페이지 CPU가 감지되지 않거나 시스템 시계 고장났음을 페이지 나타냅니다. S4/S5 (Disk에 라이브 날씨 일시중단/종료) 800*480px.gif/ 플래쉬 BIOS 사용자 프로필 bmp/ jpg/ png/ (Update) 구성품 개요...
온보드 LEDs EZ 디버그 LED 이 LED는 메인보드의 디버그 상태를 나타냅니다. BOOT - 부팅 장치가 감지되지 않거나 고장났음을 나타냅니다. VGA - GPU가 감지되지 않거나 고장났음을 나타냅니다. DDR -DRAM이 감지되지 않거나 고장났음을 나타냅니다. CPU -CPU가 감지되지 않거나 고장났음을 나타냅니다. JPWRLED1: LED 전원 입력 이...
디버그 코드 LED CPU 코어 온도 (기본값), 진행률 및 POST 도중과 이후의 오류 코드를 표시합니다. 자세한 내용은 이 매뉴얼의 디버그 코드 LED 표를 참조하십시오. 디버그 코드 LED 16진수 도표 16진수 디버그 코드 LED 0 1 2 3 4 5 6 7 8 9 A B C D E F 디스플레이...
Page 191
마이크로가 로드 되지 않음 PEI 진행 코드 PEI 코어 작동 Pre-memory CPU 초기화 작동 12 - 14 Pre-memory CPU 초기화 (CPU 모듈 특정) Pre-memory 시스템 에이전트 초기화 작동 16 - 18 Pre-Memory 시스템 에이전트 초기화 (시스템 에이전트 모듈 특정) Pre-memory PCH 초기화 작동 1A - 1C Pre-memory PCH 초기화...
Page 192
CPU 마이크로-코드 발견되지 않음 또는 마이크로-코드 업데이트 실패 내부 CPU 오류 Reset PPI 를 사용할 수 없음 5C - 5F AMI 오류를 위한 예비용 코드 DXE 진행 코드 DXE 코어 작동 NVRAM 초기화 PCH Runtime 서비스 설치 CPU DXE 초기화 작동 64 - 67 CPU DXE 초기화...
Page 193
USB 감지 USB 활성화 9E -9F AMI 코드를 위한 예비용 코드 IDE 초기화 작동 IDE 리셋 IDE 감지 IDE 활성화 SCSI 초기화 작동 SCSI 리셋 SCSI 감지 SCSI 활성화 확인 암호 설정 설치 프로그램 시작 설치 입력 대기 부팅 준비 레거시...
Page 194
Legacy Option ROM에 대한 공간이 없음 콘솔 출력 장치가 없음 콘솔 입력 장치가 없음 유효하지 않은 비밀번호 로딩 부팅 옵션 오류 (LoadImage 오류 반환) 부팅 옵션 실패 (StartImage 오류 반환) 플래시 업데이트 실패 규약 재설정을 사용할 수 없음 S3 Resume 진행 코드 S3 다시...
ACPI 상태 코드 다음 코드는 부팅 후 운영 체제가 ACPI 모드를 실행한 후에 나타납니다. S1 절전 상태 실행 S2 절전 상태 실행 S3 절전 상태 실행 S4 절전 상태 실행 S5 절전 상태 실행 S1 절전 상태로부터 회복 S2 절전 상태로부터 회복 S3 절전...
MSI 센터는 게임 설정을 쉽게 최적화하고 콘텐츠 생성 소프트웨어를 원활하게 사용할 수 있도록 지원하는 응용 프로그램입니다 . 또한 PC 및 기타 MSI 제품에 대한 LED 빛 효과를 제어하고 동기화할 수 있습니다 . MSI 센터를 사용하면 이상적인 모드를 사용자 지정하고 , 시스템...
MSI UEFI BIOS는 UEFI(Unified Extensible Firmware Interface) 구성과 호환 가능 합니다. UEFI는 기존 BIOS가 달성 할 수없는 많은 새로운 기능과 장점을 가지고 있으며 향후 BIOS를 완전히 대체 할 것입니다. MSI의 UEFI BIOS는 새로운 칩셋의 기능을 최대한 활용하기 위해 기본 부팅 모드로 UEFI를 사용합니다.
F12: 화면을 캡처한 후 USB 플래시 드라이브에 저장(FAT/ FAT32 포맷 전용) Ctrl+F: 검색 페이지로 이동 * F10 키를 누르면 확인 대화창이 나타나며 변경사항에 대한 정보를 제공합니다. Yes(예) 또는 No(아니요)를 클릭하여 선택을 확인합니다. BIOS 사용자 가이드 BIOS 설정에 대한 자세한 사항은 다음의 주소를 http://download.msi.com/manual/mb/Intel600BIOSkr.pdf 참조 하시거나 QR 코드를 스캔하십시오. UEFI BIOS...
재설정하려면 CMOS 클리어 점퍼 섹션을 참조하세요. BIOS 업데이트 M-FLASH로 BIOS 업데이트 업데이트 하기전: 구입한 모듈에 맞는 최신 BIOS 파일을 MSI 웹사이트에서 다운로드한 후 BIOS 파일을 USB 플래시 드라이브에 저장합니다. BIOS 업데이트: 1. Multi-BIOS 스위치를 사용하여 대상 BIOS ROM으로 전환합니다. 메인보드에 이 스위치가...
Page 200
2. BIOS 파일의 이름을 MSI.ROM으로 변경하고 USB 저장 장치의 루트에 저장합니다. 3. CPU_PWR1및 ATX_PWR1에 전원 공급 장치를 연결합니다. (전원 공급 장치만 필요합니다.) 4. MSI.ROM 파일이 저장된 USB 플래쉬 드라이브를 후면 I/O 패널의 플래쉬 BIOS 포트에 연결합니다. 5. 플래쉬 BIOS 버튼을 눌러 BIOS를 플래쉬하면 LED 표시등이 깜빡이기 시작합니다.
包裝內容 請檢查您的主機板包裝的內容 , 應包含 : 主機板 MEG Z690 GODLIKE 快速指引 印刷文件 DIY 支架套裝快速指引 軟體 驅動程式&工具軟體 USB 隨身碟 SATA 6Gb/s 連接線 LED JRGB Y 連接線 LED JCORSAIR 連接線 LED JRAINBOW 連接線 連接線 M-VISION Dashborad 連接線 系統面板連接線 溫度感測器線 DP to Mini-DP 連接線...
JFP1, JFP2: 系統面板接頭 這些接頭用於連接前面板的開關和 LED 指示燈 。 Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch...
JUSB1~2: USB 3.2 Gen 2x2 Type-C 接頭 這些接頭可供連接前面板上的 USB 3.2 Gen 2x2 20Gbps Type-C 接頭 。 這個接頭具有防呆 設計 。 請務必以相對應的方向正確連接 。 USB Type-C 連 JUSB1/ 2 接線 前面板上的 USB Type-C 連接埠 JUSB3~4: USB 3.2 Gen 1 接頭 這些接頭用於連接前面板的 USB 3.2 Gen 1 5Gbps 連接埠 。 Power USB2.0+ USB3_RX_DN...
內建 LED 指示燈 除錯 LED 指示燈 這些 LED 指示燈會表示主機板的偵錯狀態 。 BOOT - 表示未偵測到開機裝置或已故障 。 VGA - 表示未偵測到顯示晶片或已故障 。 DDR - 表示未偵測到記憶體或已故障 。 CPU - 表示未偵測到 CPU 或已故障 。 JPWRLED1: LED 電源接頭 零售商使用此連接器演示內載 LED 燈 JPWRLED1 - LED 電源接頭 LED_SW1: EZ LED 指示燈控制 此開關用於打開/關閉主機板上的所有...
除錯代碼 LED 除錯代碼 LED 會在 POST 期間及之後顯示進度與錯誤碼 。 詳細資料請參閱 「除錯代碼 LED」 表 。 除錯代碼 LED 十六進位字元表 十六進位 除錯代碼 0 1 2 3 4 5 6 7 8 9 A B C D E F LED 燈號 開機階段 Security (SEC) – 前期低階初始化 Pre-EFI Initialization (PEI) –...
Page 296
JFP1, JFP2: 前置面板接口 这些接口连接至前置面板上的开关和 LED 灯。 Buzzer JFP2 Speaker Speaker - Buzzer + Buzzer - Speaker + Power LED Power Switch JFP1 Reserved HDD LED Reset Switch HDD LED + Power LED + HDD LED - Power LED - Reset Switch Power Switch Reset Switch Power Switch...
Page 301
JUSB1~2: USB 3.2 Gen 2x2 Type-C 接口 这些接口允许您在前置面板上来连接 USB 3.2 Gen 2x2 20Gbps Type-C 接口。 该接口具有 防呆设计。 当您连接电缆时, 请务必将其与相应的方向连接。 USB Type-C 电缆 JUSB1/ 2 前置面板上的 USB Type-C 端口 JUSB3~4: USB 3.2 Gen 1 接口 这些接口允许您在前置面板上来连接 USB 3.2 Gen 1 5Gbps 端口。 Power USB2.0+ USB3_RX_DN...
Page 313
板载 LED 灯 简易侦错 LED 灯 LED 指示灯在主板中的侦错状态。 BOOT - 表示启动设备无法检测或故障。 VGA - 表示 GPU 无法检测或故障。 DDR - 表示 DRAM 无法检测或故障。 CPU - 表示 CPU 无法检测或故障。 JPWRLED1: LED 电源输入 此接口是被零售商用来演示板载 LED 灯。 JPWRLED1 - LED 电源输入 LED_SW1: 简易 LED 灯控制 此开关用于打开...
Page 314
侦错代码 LED 灯 开机并在 POST 之后, 侦错代码 LED 灯将会显示 CPU 内核温度 (默认), 进度和错误代码。 详情请参阅侦错代码 LED 灯表。 侦错代码 LED 灯 十六进制字符表 十六进制 侦错代码 0 1 2 3 4 5 6 7 8 9 A B C D E F LED 灯显示 启动阶段...
Page 324
2. 重新命名 BIOS 文件为 MSI.ROM, 并将其保存到 USB 存储设备的根目录中 (FAT32 格式)。 3. 连接电源供应器到 CPU_PWR1 和 ATX_PWR1。 (无需安装 CPU 和内存。 ) 4. 插入内有 MSI.ROM 文件的 USB 存储设备到后置 I/O 面板的更新 BIOS 端口上。 5. 按更新 BIOS 按钮刷新 BIOS, LED 开始闪烁。 6. 处理完成后, LED 将熄灭。...
Page 325
∙ This device may not cause harmful interference. ∙ This device must accept any interference received, including interference that may cause undesired operation. MSI Computer Corp. 901 Canada Court, City of Industry, CA 91748, USA (626)913-0828 www.msi.com...
Page 326
∙ ErP Directive 2009/125/EC Compliance with these directives is assessed using applicable European Harmonized Standards. The point of contact for regulatory matters is MSI, MSI-NL Eindhoven 5706 5692 ER Son. Products with Radio Functionality (EMF) This product incorporates a radio transmitting and receiving device. For computers in normal use, a separation distance of 20 cm ensures that radio frequency exposure levels comply with EU requirements.
Page 328
∙ Users should contact the local authorized point of collection for recycling and disposing of their end-of-life products. ∙ Visit the MSI website and locate a nearby distributor for further recycling information. ∙ Users may also reach us at gpcontdev@msi.com for information regarding proper Disposal, Take-back, Recycling, and Disassembly of MSI products.
Page 329
MSI will comply with the product take back requirements at the end of life of MSI- branded products that are sold into the EU. You can return these products to local collection points.
Page 330
MSI će poštovati zahtev o preuzimanju ovakvih proizvoda kojima je istekao vek trajanja, koji imaju MSI oznaku i koji su prodati u EU. Ove proizvode možete vratiti na lokalnim mestima za prikupljanje.
Page 331
MSI si adeguerà a tale Direttiva ritirando tutti i prodotti marchiati MSI che sono stati venduti all’interno dell’Unione Europea alla fine del loro ciclo di vita.
Page 332
Việt Nam RoHS Kể từ ngày 01/12/2012, tất cả các sản phẩm do công ty MSI sản xuất tuân thủ Thông tư số 30/2011/TT-BCT quy định tạm thời về giới hạn hàm lượng cho phép của một số hóa chất độc hại có trong các sản phẩm điện, điện tử”...
Page 333
Alternatively, please try the following help resources for further guidance. ∙ Visit the MSI website for technical guide, BIOS updates, driver updates, and other information: http://www.msi.com ∙ Register your product at: http://register.msi.com Revision History ∙...