Advertisement
POSSIBLE SETTINGS BY PUSH BUTTONS
TO START OR END AN ADJUSTMENT SESSION, press and hold either push button until the LED flashes or
stops flashing.
TO SCROLL THROUGH THE
PARAMETERS, press the right push
button.
TO CHANGE THE VALUE OF THE
CHOSEN PARAMETER, press the left
push button.
TO RESET TO FACTORY VALUES, press and hold both push buttons until both LEDs flash.
ACCESS CODE
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
Once you have saved an access code, you always need to enter this code to unlock the sensor.
If you forget the access code, cycle the power. For the first minute, you can access the sensor without an access code.
TROUBLESHOOTING
Door remains closed. LED is off.
Door does not react as expected.
Door opens and closes
constantly.
Door opens for no apparent
reason.
Vehicle detection filter is used,
but pedestrians are still detected.
LED flashes quickly after
unlocking.
Sensor does not respond to the
remote control.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor/device; therefore,
BEA, Inc. does not guarantee any use of the sensor outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certifi ed for pedestrian doors, IDA-certifi ed for doors/gates, and
factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring that the sensor
system installation is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer recommendations
and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must be performed during each service
call – examples of these safety inspections can be found on an AAADM safety information label (e.g. ANSI/DASMA 102, ANSI/DASMA 107).
Verify that all appropriate industry signage and warning labels are in place.
General Tech Questions: techservices-us@beasensors.com | Tech Docs: www.BEAsensors.com
Page 4 of 4
Page 4 of 4
Sensor power is off.
Improper output configuration on
sensor.
The sensor is disturbed by door
motion or vibrations caused by door
motion.
It rains and the sensor detects
raindrops or vibrations.
In highly reflective environments, the
sensor detects objects outside of its
detection field.
Chosen value is not optimal for the
given application.
Sensor needs access code to unlock.
Batteries in the remote control are
weak or installed improperly.
Can't find your answer? Visit www.beainc.com or scan QR code for Frequently Asked Questions!
Tech Support & Customer Service: 1-800-523-2462
1 FIELD SIZE
2 HOLD-OPEN TIME
3 OUTPUT CONFIGURATION
4 DETECTION MODE
5 DETECTION FILTER
Parameter number
Value (factory values)
Check wiring and power supply.
Check the output configuration setting on
each sensor connected to the door operator.
Ensure sensor is secured properly.
Ensure detection mode is unidirectional.
Increase tilt angle.
Increase detection filter value.
Reduce field size.
Ensure detection mode is unidirectional.
Increase detection filter value.
Change the antenna angle.
Reduce field size.
Increase detection filter value.
Increase detection filter value.
Decrease sensor angle.
Increase mounting height.
Ensure detection mode is unidirectional.
Enter correct access code.
If you forgot the code, cycle the power to
access the sensor without access code.
Change or delete the access code.
Check batteries and change if necessary.
75.5835.05 FALCON FAMILY 20190822
75.5835.05 FALCON FAMILY 20190822
(7)
(0)
(1)
(2)
(1)
Advertisement
