Omega DP25B-E Quick Start

5
Scaling With Known Loads
(Continued)
6. Press MENU to store IN!1. The unit displays:
7. Press /TARE. The unit displays the last setting for RD!1.
8. Change RD!1 as necessary:
• Press /TARE to scroll to the digit(s) you want to change
(it flashes on the display).
• Press /MAX to change the value of the flashing digit. Values
can range from 0 to 9. For the first digit, you can also enter a
minus sign (–) or –1.
9. Press MENU to store the value shown for RD!1.
The unit displays:
To identify the maximum known load ( IN!2 and RD!2 ):
1. Apply the maximum known load (100%).
2. Repeat steps 4–9 above, for IN!2 and RD!2.
Once you've completed all steps, the unit displays:
To begin operation:
Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the display).
When a numeric reading appears, the unit is
operational.
Scaling Without Known Loads
For 4-20 mA sensors, the values for the minimum and maximum
input loads are always as follows:
• Minimum load ( IN!1 ) — 2000
• Maximum load ( IN!2 ) — 9999.
If your installation uses a different sensor type, you must calculate
the values for IN!1 and IN!2 before proceeding with the steps
below. Use the formula provided in the Operator's Manual.
To define the minimum load ( IN!1 and RD!1 ):
1. If it's not already shown, press MENU until
the unit displays:
2. Press /TARE. The unit displays:
6
Scaling Without Known Loads (
Continued)
3. Press /TARE again. The unit displays the
last setting for IN!1.
(The first digit flashes.)
4. Change IN!1 as necessary:
• Press /MAX to set or change the digit's current value. Continue to
press /MAX until the meter displays the desired value for the
flashing digit. Values can range from 0 to 9. For the first digit, you can
also enter a minus sign (–) or –1.
• Press /TARE to scroll to the digit(s) you want to change.
5. Press MENU to store IN!1. The unit displays:
6. Press /TARE. The unit displays the last
setting for RD!1. (The first digit flashes.)
7. Change RD!1 as necessary:
• Press /MAX until the meter displays the desired value for the
flashing digit. Values can range from 0 to 9. For the first digit, you
can also enter a minus sign (–) or –1.
• Press /TARE to scroll to the digit(s) you want to change.
8. Press MENU to store the value shown for RD!1.
The unit displays:
To define the maximum load ( IN!2 and RD!2 ):
1. Repeat steps 3–8 above, entering the values for IN!2
and RD!2.
2. Once you've completed all steps, the unit displays:
To begin operation:
Reinitialize the unit (press RESET twice or
press MENU until RST flashes on the
display). When a numeric reading appears,
the unit is operational.
Determining Reading Offset
The run mode reading for meters scaled without known loads may
reflect an offset. For example, say you set RD!1 to 0 and RD!2 to
100, but when the minimum load is applied, a negative value of –1.5
displays on the front panel.
To correct the reading offset:
1. With zero load applied, note the reading on the display.
2. Subtract that amount from the RD!1 and RD!2 values you
originally entered.
In the example, the offset would be –1.5. If RD!1 is to read 0 in
Run Mode, it must be reentered as 1.5. RD!2 must likewise be
reentered as 101.5 if the meter is to read 100 when the
maximum load is applied.
3. Repeat the steps for "Scaling Without Known Loads," but when
the values for IN!1 and IN!2 display, do not change them.
Instead, press MENU to move to the prompts for RD!1 and RD!2
and make the necessary changes.
4. Reinitialize the unit and resume operation.
WARRANTY/DISCLAIMER
OMEGA ENGINEERING, INC. warrants this unit to be free of defects
in materials and workmanship for a period of 61 months from
date of purchase. OMEGA's WARRANTY adds an additional one (1)
month grace period to the normal five (5) year product warranty
to cover handling and shipping time. This ensures that OMEGA's
customers receive maximum coverage on each product.
If the unit malfunctions, it must be returned to the factory for evalua-
tion. OMEGA's Customer Service Department will issue an Authorized
Return (AR) number immediately upon phone or written request.
Upon examination by OMEGA, if the unit is found to be defective, it
will be repaired or replaced at no charge. OMEGA's WARRANTY does
not apply to defects resulting from any action of the purchaser, includ-
ing but not limited to mishandling, improper interfacing, operation
outside of design limits, improper repair, or unauthorized modifica-
tion. This WARRANTY is VOID if the unit shows evidence of having
been tampered with or shows evidence of having been damaged as a
result of excessive corrosion; or current, heat, moisture or vibration;
improper specification; misapplication; misuse or other operating
conditions outside of OMEGA's control. Components in which wear
is not warranted, include but are not limited to contact points, fuses,
and triacs.
OMEGA is pleased to offer suggestions on the use of its vari-
ous products. However, OMEGA neither assumes responsibil-
ity for any omissions or errors nor assumes liability for any
damages that result from the use if its products in accordance
with information provided by OMEGA, either verbal or writ-
ten. OMEGA warrants only that the parts manufactured by
the company will be as specified and free of defects. OMEGA
MAKES NO OTHER WARRANTIES OR REPRESENTATIONS OF
ANY KIND WHATSOEVER, EXPRESSED OR IMPLIED, EXCEPT
THAT OF TITLE, AND ALL IMPLIED WARRANTIES INCLUDING
ANY WARRANTY OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE ARE HEREBY DISCLAIMED.
LIMITATION OF LIABILITY: The remedies of purchaser set
forth herein are exclusive, and the total liability of OMEGA
with respect to this order, whether based on contract, warran-
ty, negligence, indemnification, strict liability or otherwise,
shall not exceed the purchase price of the component upon
which liability is based. In no event shall OMEGA be liable for
consequential, incidental or special damages.
CONDITIONS: Equipment sold by OMEGA is not intended to be used,
nor shall it be used: (1) as a "Basic Component" under 10 CFR 21 (NRC),
used in or with any nuclear installation or activity; or (2) in medical appli-
cations or used on humans. Should any Product(s) be used in or with
any nuclear installation or activity, medical application, used on humans,
or misused in any way, OMEGA assumes no responsibility as set forth
in our basic WARRANTY/DISCLAIMER language, and, additionally,
purchaser will indemnify OMEGA and hold OMEGA harmless from any
liability or damage whatsoever arising out of the use of the Product(s)
in such a manner.
RETURN REQUESTS/INQUIRIES
Direct all warranty and repair requests/inquiries to the OMEGA
Customer Service Department. BEFORE RETURNING ANY
PRODUCT(S) TO OMEGA, PURCHASER MUST OBTAIN AN
AUTHORIZED RETURN (AR) NUMBER FROM OMEGA'S CUSTOMER
SERVICE DEPARTMENT (IN ORDER TO AVOID PROCESSING
DELAYS). The assigned AR number should then be marked on the
outside of the return package and on any correspondence.
FOR WARRANTY RETURNS,
FOR NON-WARRANTY REPAIRS,
please have the following consult OMEGA for current repair
information available BEFORE charges. Have the following
contacting OMEGA:
information available BEFORE
contacting OMEGA:
1. Purchase Order number
under which the product 1. Purchase Order number to cover
was PURCHASED,
the COST of the repair or
2. Model and serial number of the calibration,
product under warranty, and 2. Model and serial number of the
3. Repair instructions and/or product, and
specific problems relative
3. Repair instructions and/or specific
to the product. problems relative to the product.
OMEGA's policy is to make running changes, not model changes,
whenever an improvement is possible. This affords our customers
the latest in technology and engineering.
OMEGA is a trademark of OMEGA ENGINEERING, INC.
© Copyright 2018 OMEGA ENGINEERING, INC. All rights reserved.
This document may not be copied, photocopied, reproduced,
translated, or reduced to any electronic medium or machine-readable
form, in whole or in part, without the prior written consent of OMEGA
ENGINEERING, INC.
MQS3597/0918
For complete product manual:
www.omega.com/manuals/manualpdf/M3597.pdf
TM
DP25B-E
Process Panel Meter
omega.com info@omega.com
Servicing North America:
U.S.A. Omega Engineering, Inc.
Headquarters: Toll-Free: 1-800-826-6342 (USA & Canada only)
Customer Service: 1-800-622-2378 (USA & Canada only)
Engineering Service: 1-800-872-9436 (USA & Canada only)
Tel: (203) 359-1660 Fax: (203) 359-7700
e-mail: info@omega.com
For Other Locations Visit omega.com/worldwide
The information contained in this document is believed to be correct, but
OMEGA accepts no liability for any errors it contains, and reserves the right to
alter specifications without notice.
WARNING: These products are not designed for use in, and should not be used for, patient-
connected applications.
This device is marked with the international caution symbol. It is important to read the
Setup Guide before installing or commissioning this device, as the guide contains
important information relating to safety and EMC.
It is the policy of OMEGA to comply with all worldwide safety and EMC/EMI regulations that apply.
OMEGA is constantly pursuing certification of its products to the European New Approach Directives.
OMEGA will add the CE mark to every appropriate device upon certification.
The information contained in this document is believed to be correct, but OMEGA Engineering, Inc.
accepts no liability for any errors it contains, and reserves the right to alter specifications without
notice.