Philips MCM530 Service Manual page 3

SPECIFICATIONS
GENERAL:
Mains voltage : 110-127V/220-240V Switchable for /21
120V ± 10% for /37
230V ± 10% for /22
230-240V for /30
Mains frequency : 50/60Hz
Clock accuracy : < 4 seconds per day
Dimension centre unit : 175 x 268 x 316mm
Power consumption
Active : 60W for MCM530/22/30/37
Active : 69W for MCM530/21
Active : 110W for MCM590/21
Standby : < 15W (DEMO mode off)
ECO Power Standby : < 0.5W for /22/30/37
ECO Power Standby : < 1W for /21
TUNER:
FM
Tuning range
Grid
IF frequency
Aerial input
Sensitivity at 26dB S/N
Selectivity at 600kHz bandwidth
Image rejection
Distortion at RF=1mV, dev. 75kHz
-3dB Limiting point
Crosstalk at RF=1mV, dev. 40kHz
MW
Tuning range
Grid
IF frequency
Aerial input
Sensitivity at 26dB S/N
Selectivity at 18kHz bandwidth
IF rejection
Image rejection
Distortion at RF=50mV, M=80%
AMPLIFIER:
Output power
L & R : 2 x 75W RMS (6Ω, 1kHz, 10% THD)
: 2 x 125W RMS (4Ω, 1kHz, 10% THD)
for MCM590/21
Output power (6 Ω, 60Hz-12.5kHz, 10% THD)
L & R : 2 x 70W FTC for MCM530/37
: 87.5-108MHz
: 50kHz
100kHz for /21/37
: 10.7MHz ± 25kHz
: 75 Ω coaxial
300 Ω click fit for /37
: < 7µV
: > 25dB
: > 25dB [> 75dB]
: < 3%
: < 8µV
: > 18dB
: 531-1602kHz
530-1700kHz for /21/37
: 9kHz
10kHz for /21/37
: 450kHz ± 1kHz
: Frame aerial
: < 4.4mV/M
: > 18dB
: > 45dB
: > 28dB
: < 5%
1-3
Frequency response within -3dB
MAX Sound
Digital Sound Control (DSC) : Jazz / Rock / Pop / Optimal
Virtual Environment Control (VEC) : Cyber Hall / Concert /
Input sensitivity
Aux in (at 1kHz) : 500mV at 600 Ω
CDR in (at 1kHz) : 1000mV at 600 Ω
USB (at 1kHz) : 830mV at 600 Ω
Output sensitivity
Headphone output at 32 ohm : 15mW ± 2dB (Max. vol.)
5DTC:
Measurement done directly at the connector on the board.
Output Resistance
Output Voltage (0dB, 1kHz)
Channel Unbalance
Channel Separation (1kHz)
Frequency Response (±3dB) : 20Hz-20kHz
Signal to Noise Ratio
MP3-CD Bit Rate
Sampling Frequencies
USB:
Measurement done directly at the connector on the board.
Output Resistance
Output Voltage (0dB, 1kHz)
Channel Unbalance
THD + Noise (0dB, 1kHz)
Channel Separation (0dB, 1kHz) : > 40dB
Frequency Response (±3dB)
Signal to Noise Ratio
[....] Values indicated are for "ECO6 Cenelec Board" only.
: 50Hz-16kHz
: On / Off
Cinema / Off
: < 100 Ω
: 0.5Vrms ± 1dB (unloaded)
: < ±1dB
: > 60dB
: > 76dBA
: 32-256 kbps
: 32, 44.1, 48 kHz
: < 1.5 kΩ
: 830mVrms ± 1.5dB
(R = 33 kohm)
L
: < ±1dB
: < 0.3%
: 20Hz-20kHz
: > 75dBA