Advertisement
Quick Links
Mulching Kit
GrandStand
Cutting Unit
Model No. 134-3217
Safety
Rear Discharge or Mulch
Grass
WARNING
Without the grass guard mounted in place,
you and others are exposed to blade contact
and thrown debris. Contact with rotating
mower blade(s) and thrown debris will cause
injury or death.
• Never remove the grass guard from the
mower because the grass guard routes
material down toward the turf. If the
grass guard is ever damaged, replace it
immediately.
• Never put your hands or feet under the
mower.
• Never try to clear the discharge area or
mower blades unless you engage the
parking brake, disengage the power take
off (PTO) lever, shutoff the engine, remove
the ignition key, and wait for all motion
to stop. Also pull the wire off the spark
plug(s).
Ensure that the mower has the rear grass guard to
disperses clippings to the rearward and down toward
the turf, while in rear discharge mode.
To mulch grass clippings, install the baffles on the
mower deck as instructed in the following procedures.
© 2019—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
Mower With 91cm Rear Discharge TURBO FORCE
Register at www.Toro.com.
Form No. 3431-157 Rev C
Installation Instructions
Original Instructions (EN)
All Rights Reserved *3431-157* C
Printed in the USA.
®
Advertisement
Related Manuals for Toro GrandStand Mulching Kit
Summary of Contents for Toro GrandStand Mulching Kit
- Page 1 To mulch grass clippings, install the baffles on the mower deck as instructed in the following procedures. © 2019—The Toro® Company Register at www.Toro.com. Original Instructions (EN) All Rights Reserved *3431-157* C 8111 Lyndale Avenue South Printed in the USA.
-
Page 2: Installation
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the mower. – No parts required Remove the existing blades. – No parts required Drill the mower deck. Left baffle (3 holes) Right baffle (4 holes) Install the baffles. - Page 3 Drilling the Mower Deck No Parts Required Procedure g283723 At the left side of the mower deck, drill the 4 pilot holes in the deck with a 10 mm (3/8 inch) drill bit as shown in Figure g283721 g283724 Figure 2 1.
- Page 4 mower deck (Figure 3) with 3 carriage bolts (3/8 x 1 inch) and 3 flange locknuts (3/8 inch). Align the holes in the left baffle (3 holes) with the 2 holes that you drilled in the side of the mower Installing the Baffles deck (Figure...
- Page 5 Assemble the kicker fitting to the deck (Figure with 2 carriage bolts (3/8 x 1 inch) and 2 flange locknuts (3/8 inch). Torque the flange locknuts to 37 to 45 N∙m (27 Installing the Kicker Fittings to 33 ft-lb). At the left side of the mower deck, align the slots in the kicker fitting with the 2 holes 10 mm Parts needed for this procedure: (3/8 inch) that you drilled into the mower deck...
- Page 6 fitting to the deck, and remove the kicker fitting (Figure Note: Retain the carriage bolts and kicker fitting for installing the mulching kit. Installing the Recycler Blades Parts needed for this procedure: Recycler blades (sold separately) Procedure WARNING A blade is sharp. Contact with a sharp blade can cause serious personal injury.
-
Page 7: Removing The Baffles
Removing the Baffles flange locknuts (3/8 inch) that secure the kicker fitting to the deck, and remove the kicker fitting Note: Determine the left and right sides of the (Figure machine from the normal operating position. Note: Retain the carriage bolts and kicker fitting Remove the 3 carriage bolts (3/8 x 1 inch) and for installing the mulching kit. -
Page 8: Operation
Operation to the mulching-plate flange and the small baffle of the mower deck, and remove the left baffle (Figure 13). Selecting the Proper Height Note: Retain the carriage bolts, flange locknuts, and baffle for installing the mulching kit. of Cut Remove approximately one inch or no more than 1/3 of the grass blade when cutting.