New Mixer Navigation Tools; Equalizer Knobs; Added Message 1; Added Mixer Setup - Korg D32XD Upgrade Manual

New MIXER Navigation Tools

Assigning Tab Pages to the Locate keys
Tab pages within the MIXER page can be registered to the
LOC1/IN–LOC6 keys for quick access.
(1) In the MIXER page, access the tab page that you want to
register.
(2) Hold down the MIXER key and press the STORE key;
the Stored Page dialog box will appear.
If you decide not to register this page, press the Exit but-
ton or press the STORE key once again.
(3) Press the LOC1/IN, LOC2/OUT, LOC3/TO, LOC4/END,
LOC5, or LOC6 key to register the current tab page to
that key. Registration is complete as soon as you press
the key, and the dialog box will close.
With the factory settings, the following pages are registered.
LOC1 INPUT/OUTPUT/CH ASSIGN, "Ch Assign" tab page
LOC2 FADER/PAN/AUTOMATION, "Automation" tab page
LOC3 PAIR/GROUP, "Ch Pair" tab page
LOC4 ANALOG COMP, "Comp1–8" tab page
LOC5 EQ/ATT/PHASE, "MasterEQ" tab page
LOC6 SOLO/MONITOR, "CueLevel" tab page
Once the tab page has been assigned, then simply holding
down the MIXER key and pressing one of the LOC1/IN–
LOC6 keys will move you directly to that registered tab page
within the MIXER.
Moving between tab pages
You can move between tab pages within MIXER page mode
by holding down the MIXER key and using the Cursor keys
(√, ®). You can move between MIXER page modes by hold-
ing down the MIXER key and using the Cursor keys (π, †)
(→Manual: p.99).

Equalizer knobs

When the "Master EQ" tab page is displayed, you can now
use the equalizer knobs to edit the GAIN, FREQ, and Q val-
ues (→Manual: p.10, 49, 111).
The equalizer band keys (High...Low) cannot be used in the "Mas-
ter EQ" tab page. You will need to select the equalizer band in
the screen.
Please refer to Page 3 of this document for more information on
the operation of the control knobs when using the Master EQ.

Added message 1

In ¯ Out Samples under 4096.
To ¯ End Samples under 2048.
The region specified for the track editing operation is too
small.
Added message 2
Trigger recording is not available for the master
track.
You can't perform trigger recording if the MASTER TRACK
STATUS key is set to REC.
6

Added Mixer SetUp

Mixer Setup lets you store the current mixer settings for sub-
sequent recall at a later time.
This allows you to store mixer settings that you use fre-
quently, and then recall them when creating a new song. You
can also use this method to copy mixer settings to a different
song.
The current mixer settings are stored as a "mixer setup pro-
gram." You can store twenty of these mixer setup programs.
A mixer setup program contains all the mixer parameters
that are included in the song. It also contains the current
analog compressor settings.
The mixer setup programs that you store can be backed-up
and restored as "UserData"→"Mixer SetUp Data"
(→Manual: p.82)
A mixer setup contains the following parameters.
• Channel Assign, Source Select (CD or S/P DIF), Sub
Mixer, and AdatOut assignments
• Pair, Group (D32XD only)
• Fader, Pan, Play/Rec EQ
• ATT, CH ON, Phase, AUX/EFF Send, Rec Send
• Effect (all settings including the parameters being edited)
• Master Fader, Master EQ, Send Out level, Send Select All
• Solo, Monitor, Cue, rhythm output assignment, rhythm
volume
• Analog Compressor
Additional parameters included in Mixer Setup
• REC/PLAY, MASTER TRACK STATUS, Group (D16XD
only)

Accessing the Mixer Setup screen

Press the top panel MIXER key to display the Page Jump
Menu screen (
Press the MIXER SET UP button to open the Mixer Setup
screen.
(→Manual: p.170)

Storing a mixer setup

Here's how to store the current mixer settings as a mixer setup
program.
(→Manual: p.170)
(1) Make the current mixer settings are the ones that you
want to store.
(2) Access the MIXER, "MIXER SET UP," "MixerSetUp" tab
page.
(3) In the list, press to highlight the program in where you
want to store the current settings (i.e., the program you
want to overwrite).
Manual: p.99).
→
You can't store a mixer setup while a song is playing.