Table of Contents
Advertisement
Quick Links
Owner's Installation and Operation Manual
Model 1330E
Wood Only Central Furnace
Report No. 0215WH056E
0215WH056S
This unit is certified UL-391(R2014)
U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with the 2016 particulate
emission standards. Not approved for sale after
May 15, 2020
Installation is to be preformed by a
qualified installer.
SAVE THESE INSTRUCTIONS
United States Stove Company
227 Industrial Park Rd.
852816-4804F
South Pittsburg, TN 37380
Advertisement
Table of Contents
Related Manuals for Ashley 1330E
Summary of Contents for Ashley 1330E
- Page 1 Owner’s Installation and Operation Manual Model 1330E Wood Only Central Furnace Report No. 0215WH056E 0215WH056S This unit is certified UL-391(R2014) U.S. ENVIRONMENTAL PROTECTION AGENCY Certified to comply with the 2016 particulate emission standards. Not approved for sale after May 15, 2020 Installation is to be preformed by a qualified installer.
- Page 2 CAUTION: • Power source not controlled by furnace main disconnect. • Respect all local and national codes when installing this unit. • This unit is not to be connected to a chimney flue serving another appliance. • This unit is designed to burn solid hardwood only. 40.65 21.00 26-3/4...
-
Page 3: Specifications
11.6” X 11.5” Weight (lbs): 350lbs This manual describes the installation and operation of the Ashley, 1330E wood heater. This heater meets the 2016 U.S. Environmental Protection Agency’s emission limits for wood heaters sold after May 15, 2016. Under specific EPA test conditions this heater has been shown to deliver heat at a rate of 18,850 –... - Page 4 Safety • WARNING: Do not operate with fuel loading or ash removal doors open. • Do not connect this unit to a chimney flue serving another appliance. • WARNING DANGER: Risk of fire or explosion. Do not burn garbage, gasoline, naphtha, motor oil, or other inappropriate materials.
-
Page 5: Tools And Materials Needed For Installation
Unpacking And Preassemble UNPACKING 1. Remove all packaging from the furnace. 2. Remove the supplied parts from the furnace. BRICK ALIGNMENT Inspect for any damage. Ensure that the bricks and ash plug are positioned correctly and not broken (see illustration for proper brick arrangement). Proper Fire Brick Alignment TOOLS AND MATERIALS NEEDED FOR INSTALLATION The following is a list of tools and materials needed to install your furnace. -
Page 6: Furnace Installation
Furnace Installation INSTALLATION OPTIONS The installation of this furnace includes supplying electrical power, return (fresh air) ductwork, and supply air ductwork. This furnace may be installed in two different configurations. 1. Stand alone wood furnace 2. Add-on wood furnace See kit installation section in this manual to ensure proper assembly, installation and operation of your new furnace. -
Page 7: Floor Protector Requirements
MAINTENANCE CLEARANCES Your furnace has recommended minimum maintenance clearance requirements. These clearances insure that there is adequate room to preform maintenance and service your furnace. DO NOT store fuel within the specified clearances. See the table and diagram below to determine the clearances for your furnace. Dimension Inch mm Maintenance Clearance (Front) 24... -
Page 8: Duct Work Installation
Duct Work Installation We strongly recommend that the hot air ductwork be installed by a home heating specialist. If doing the installation yourself, before you decide which installation will best suit your needs, consult a qualified heating technician and follow his recommendations as to the safest and most efficient method of installation. This furnace can be installed in two ways, as a stand alone or parallel unit, with an existing furnace. -
Page 9: Air Filter Replacement
CENTRAL INSTALLATION Air Filter Replacement... -
Page 10: Accessory Installation
Accessory Installation ASSEMBLY OF FURNACE Your furnace requires the following items to be assembled or installed THERMODISC by the service person: COVER THERMODISC Blower and Blower Control Electrical Connections 1. Remove all parts from the unit (blower, thermodisc, and all wiring) and inspect for damage, including the firebrick as some breakage could occur during shipment. -
Page 11: Electrical Installation
Electrical Installation All electrical connections should be done by a qualified electrician It is recommended to connect the furnace to its own 15 amp 120 Volt circuit from the house power supply 105°C NOTE:Wire leads from the distribution blower are usually BOTH BLACK. -
Page 12: Chimney Installation
Chimney Installation CHIMNEY Your wood furnace may be hooked up with a factory built or masonry chimney, matching the diameter of the exhaust. If you are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). -
Page 13: Masonry Chimney
MASONRY CHIMNEY Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA) by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration and blockage. Have the chimney cleaned before the furnace is installed and operated. When connecting the furnace through a combustible wall to a masonry chimney, special methods are needed as explained in the “Combustible Wall Chimney Connector Pass-Throughs”... -
Page 14: Combustible Wall Chimney Connector Pass-Throughs
COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS Method A. 12” (304.8 mm) Clearance to Combustible Wall Member: Using a minimum thickness 3.5” (89 mm) brick and a 5/8” (15.9 mm) minimum wall thickness clay liner, construct a wall pass-through. The clay liner must conform to ASTM C315 (Standard Specification for Clay Fire Linings) or its equivalent. -
Page 15: Chimney Connector
CHIMNEY CONNECTOR Your chimney connector and chimney must have the same diameter as the furnace outlet. If this is not the case, we recommend you contact your dealer in order to insure there will be no problem with the draft. The furnace pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021”... -
Page 16: Factory Built Chimney
FACTORY BUILT CHIMNEY When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through and “T” section package, firestops (where needed), insulation shield, roof flashing, chimney cap, etc. Maintain proper clearance to the structure as recommended by the manufacturer. -
Page 17: Operation
Operation OPERATING THE PRIMARY AND SECONDARY AIR SETTINGS Primary air- is the driving air supply that feeds the fire in the heater. This air is introduced through the damper in the feed door to sustain the combustion. Secondary air – is the air supply that is typically introduced above the fire to effectively “re-burn” the smoke created in the primary combustion before the exhaust gasses exit the stove. -
Page 18: Do Not Burn
Operation The top down method of fire building is recommended for this appliance. After making sure that the stove air intake controls are fully open (both air controls open to there maximum setting). Place the largest pieces of wood on the bottom, laid in parallel and close together. Smaller pieces are placed in a second layer, crossways to the first. - Page 19 Operation NOTICE: To minimize the risk of smoke spillage when opening the door with a fire in your furnace, crack the door open no more than 1” and wait for at least 10 seconds before opening it more to allow pressure stabilization inside the furnace.
-
Page 20: Ash Disposal
wood will burn quickly if the air control’s are adjusted to admit a larger quantity of oxygen in the combustion chamber. Real operating conditions may give very different results than those obtained during testing according to the species of wood used, its moisture content, the size and density of the pieces, the length of the chimney, altitude and outside temperature. -
Page 21: Over Firing
CAUTIONS: • Ashes could contain hot embers even after two days without operating the furnace. • The ash pan can become very hot. Wear gloves to prevent injury. • Never burn the furnace with the ash trap open. This would result in over firing the furnace. Damage to the furnace and even house fire may result. -
Page 22: Maintenance
Maintenance Your wood furnace is a high efficiency furnace and therefore requires little maintenance. It is important to perform a visual inspection of the furnace every time it is emptied, in order to insure that no parts have been damaged, in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe periodically for creosote buildup or obstructions. -
Page 23: Replacement Parts
Wooden Knob 610498 Ashpan Weldment 89520 Wooden Handle 88066 5/8” Rope Gasket 34” 891097 Locking Mech, Feed Door 27960 Front Liner, 1330E 89574 Handle, Spring 27952R Air Cover 61057R Painted Top Assembly 27951 Air Slide 28043R Left Shoulder In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your dealer or directly from the appliance manufacturer. - Page 24 Replacement Parts Part No. Description 88260 Board, Ceraminc Fiber 86875 Tube, Secondary Air 28051 Brick Retainer 89066A Firebrick (4-1/2 X 9) Pumice 24103 Firebrick, Half (4-1/2 X 4-1/2) 40605 Cast Grate In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your dealer or directly from the appliance manufacturer.
- Page 25 Replacement Parts Part No. Description 68234 Assy, Blower/T’stat Brkt. 68231 Fan Cntrl Cord Assy. 80131 4 X 4 Junction Box 80232 Supply Cord 80594 Blower Assembly 89319 Blower Gasket 22140 Control Mounting Bracket 80714 F140 Thermodisc 80231 Cover, Junction Box In order to maintain warranty, components must be replaced using original manufacturers parts purchased through your dealer or directly from the appliance manufacturer.
-
Page 26: Service Record
Service Record It is recommended that your heating system is serviced regularly and that the appropriate Service Interval Record is completed. Service Provider: Before completing the appropriate Service Record below, please ensure you have carried out the service as described in the manufacturer’s instructions. - Page 27 Limited Warranty Warm Air Furnace The operation of this heater in a manner inconsistent with the owner’s manual will void the warranty and is also against federal regulations. United States Stove Company warrants to the original purchaser its heating products against premature failure of any component due to workmanship, quality, or materials as follows: TIME PERIOD: Firebox ............................
-
Page 28: How To Order Replacement Parts
How to order Replacement Parts This manual will help you obtain efficient, dependable service from your stove, and enable you to order repair parts correctly. Keep this manual in a safe place for future reference. When writing, always give the full model number which is on the nameplate attached to the stove. When ordering repair parts, always give the following information as shown in this list: 1.