Related Manuals for Philips EasyAir SNS410 MC
Summary of Contents for Philips EasyAir SNS410 MC
- Page 1 Sensors EasyAir SNS210 MC, SNS410 MC Design-in Guide Single, compact, cost-effective luminaire control Philips EasyAir SNS210 MC, SNS410 MC August 2021...
-
Page 2: Table Of Contents
Luminaire-to-luminaire distance Recommendations to design-in around EasyAir SNSx10 MC with good RF signal Mounting to a luminaire Mounting EasyAir SNS410 MC inside of a luminaire Mounting in a bracket (SMB-50) Installing EasyAir SNS210 MC with ceiling mount bracket (SNS210 MCCMP) -
Page 3: Introduction To This Guide
Introduction to this guide Thank you for choosing Philips EasyAir SNS210 MC, SNS410 MC. In this guide luminaire manufacturers will find the information required to design this product into a luminaire and configure it to suit specific applications. This design-in... -
Page 4: Warnings And Instructions
Warnings and instructions • EasyAir SNS210 MC, SNS410 MC must be used with Philips Xitanium SR LED drivers. • Do not apply mains power directly to the sensor. • Do not cover the sensor during operation or mount the sensor internal to the luminaire. -
Page 5: Introduction Of Easyair Sns210 Mc
EasyAir SNS410 MC has the same form factor as EasyAir SNS210 MC and uses the same radio tranceiver but is without the occupancy and daylight sensors. -
Page 6: Product Characteristics
Product characteristics EasyAir SNS210 MC overview EasyAir SNS210 MC contains multiple functions in one housing and uses two wires to connect with an SR driver. (See wiring diagram in the Mechanical design-in section.) Functions include: • Occupancy sensor (PIR) • Zigbee/Bluetooth •... -
Page 7: Motion Detector
Motion detector The occupancy sensor is a PIR (Passive Infrared) sensor that detects movement with an X-Y cross-area under an angle of X = 62° and Y = 84°. Two types of movements are defined as follows: • Major movement: movement of a person walking into or through an area. -
Page 8: Sensor View Shield
To prevent false triggers, the EasyAir SNS210 MC must be mounted more than 2 m away from air vents in all directions, see figures below: > 2m Luminaire > 2m > 2m > 2m Sensor view shield The sensor comes with an occupancy view shield that can be used to block the movement detection by the sensor in a certain area. -
Page 9: Light Sensor
The EasyAir SNS210 MC converts the illuminance signal into ON/OFF or dimming commands to the Philips Xitanium SR LED driver in order to maintain a constant light level on the desk. Window The sensor should be installed with a minimum distance of 0.6 m to the window to avoid the sensor looking outside. -
Page 10: Daylight Regulation And Calibration
Daylight regulation and calibration Daylight regulation without calibration When daylight-based control is switched on and no calibration is performed, the light output adjusts approximately to 500 lux times the value set for the Eco-on level. If the Eco-on level is set to 80% for example, the light output from the luminaire adjusts to approximately 400 lux in the working area. -
Page 11: Mechanical Design-In
Mechanical design-in Wire strip length Wiring Information Strip length Applicable wires 8.0 ± 0.5 mm Conductor size: solid 0.2 - 0.75 mm Conductor size: fine-stranded 0.2 - 0.75 mm Conductor size: fine-stranded 0.25 - 0.34 mm Conductor Insulation (with insulated formule) Conductor size: fine-stranded 0.25 - 0.34 mm [ Conductor: Bare Copper / Strand wire ]... -
Page 12: Wire Distance For Remote Mounting
Wire distance for remote mounting ≥ 1.5 m ≥ 1.5 m It is recommended to keep the wire distance from sensor to Xitanium SR LED driver less than 2 m and meet the wire gauge requirement to guarantee the performance. Luminaire-to-luminaire distance If multiple luminaires with EasyAir SNS210 MC are used in the same area, the distance between the different sensors... -
Page 13: Mounting To A Luminaire
Mounting in a luminaire EasyAir SNS210 MC, SNS410 MC is a luminaire-mount LED module sensor that is directly powered by a Xitanium SR LED driver. It can be mounted to a slot or a cut-out in sheet metal. SNSx10 Light shield Note: When daylight sensing is enabled, it is advised to add a light shield in between LED module and EasyAir SNS210 in case the sensor is placed close to the LED... -
Page 14: Mounting In A Bracket (Smb-50)
Mounting in a bracket (SMB-50) 65 Max. The EasyAir SNS210 MC, SNS410 MC can be mounted in a bracket (SMB 50). Refer the figures for details on mounting and design-in into luminaire. All dimensions are in mm. 26 Max. 64 Max. 60 ±... - Page 15 Installing EasyAir SNS210 MC, SNS410 MC with ceiling mount bracket (CMP/W) The ceiling mount CMP bracket is available as a bracket without any pre-mounted sensor or cable. The luminaire manufacturer needs to mount the sensor in the CMP bracket and attach cable to it. The cable and screws are available with the accessory.
-
Page 16: Labels
Labels SNS 210 MC, SNS410 MC sensors are supplied with three labels which each contain the assigned ZigBee MAC Address. For a typical application, the top two labels can be removed and discarded. For a network application using a gateway, the labels can be used to identify a luminaire and where it is installed in the building. •... -
Page 17: Xitanium Sr Led Drivers (1:N Application)
NEUTRAL SGND LINE NFC ANTENNA In case EasyAir SNS210 MC, SNS410 MC is connected to multiple Philips Xitanium SR LED drivers, the number of Connectors drivers is limited to 10. Not more than 4 drivers should LED+ LED+ have DALI power supply enabled. To minimize unnecessary... -
Page 18: Luminaire Production Test
1st second followed by dimming up to 100% in the next second. This behaviour is only visible in non-commissioned devices i.e. once grouped using Philips MasterConnect app, this behaviour will cease to exist. August 2021 Design-in Guide - EasyAir SNS210 MC... -
Page 19: Faq
Zigbee green power switch. For list of supported switches, please visit our website How does EasyAir SNS210 MC compare to Philips ActiLume? Occupancy sensing and daylight harvesting are similar. Form factors are also similar, with the face of the sensor outside the luminaire having the same size. - Page 20 Unlike traditional occupancy sensors, EasyAir SNS210 MC does not have a mechanical relay. This is a benefit of Philips SR LED drivers, as on/off is done relay-free within the driver. Devices with mechanical relays should be designed so that relay failure results in “lights on.” If an SR driver does not see a digital signal from a device for a long period of time (e.g., loose connection, sensor failure), the...
-
Page 21: Contact Details
Contact details Philips EasyAir SNS210 MC, SNS410 MC Product information: www.lighting.philips.co.uk/oem-emea/products/easy-to- integrate-wireless-sensors.html Or contact your local Philips sales representative. August 2021 Design-in Guide - EasyAir SNS210 MC... -
Page 22: Disclaimer
Disclaimer ©2021 Signify Holding B.V. All rights reserved. Note that the information provided in this document is subject to change. This document is not an official testing certificate and cannot be used or construed as a document authorizing or otherwise supporting an official release of a luminaire. The user of this document remains at all times liable and responsible for any and all required testing and approbation prior to the manufacture and sale of any... - Page 23 The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. All other trademarks are owned by Signify Holding or their respective owners.