Audio Dubbing; Insert Editing - JVC GR-D21 Instructions Manual

Audio Dubbing

The audio track can be customized only when recorded
in the 12-bit mode ( pg. 21).
NOTES:
● Audio Dubbing is not possible on a tape recorded in
16-bit audio, on a tape recorded in the LP mode or on a
blank portion of a tape.
● To perform Audio Dubbing while watching on the
television, make connections (
1
Play back the tape to locate the point where editing
will start, then press PAUSE (6)
2
While holding A.DUB (e)
T
press PAUSE (6) . "6e"
appear.
3
h
Press PLAY (4) , then begin "narrating".
Speak into the microphone.
• To pause dubbing, press PAUSE (6)
4
To end Audio Dubbing, press PAUSE (6)
O
STOP (5) .
To hear the dubbed sound during playback . . .
..... set "12BIT MODE" to "SOUND 2" or "MIX" in the
Menu Screen ( pg. 25).
NOTES:
● Sound is not heard from the speaker during Audio
Dubbing.
● When editing onto a tape that was recorded at 12-bit, the
old and new soundtracks are recorded separately.
● If you dub onto a blank space on the tape, the sound may
be disrupted. Make sure you only edit recorded areas.
● If feedback or howling occurs during TV playback, move
the camcorder's microphone away from the TV, or turn
down the TV's volume.
● If you change from 12-bit to 16-bit in mid-recording and
then use the tape for Audio Dubbing, it is not effective
from the point where 16-bit recording began.
● During Audio Dubbing, when the tape moves to scenes
recorded in the LP mode, scenes recorded in 16-bit audio
or a blank portion, Audio Dubbing stops (
● To perform Audio Dubbing with a video unit connected to
the camcorder's AV connector, first set "S/AV INPUT" to
"ON" in the Menu Screen (GR-D31 only,
"AUX" appears instead of "MIC".
Stereo microphone
pg. 15).
T
.
j
on the remote control,
y
and "MIC" (GR-D31 only)
T
.
T
, then
pg. 44).
pg. 24).

Insert Editing

You can record a new scene into a previously recorded
tape, replacing a section of the original recording with
minimal picture distortion at the in and outpoints. The
original audio remains unchanged.
NOTES:
● Before performing the following steps, make sure that
"TIME CODE" is set to "ON" in the Menu Screen
( pg. 24, 25).
● Insert Editing is not possible on a tape recorded in the LP
mode or on a blank portion of a tape.
● To perform Insert Editing while watching in the television,
make connections ( pg. 15).
1
Play back the tape, locate the Edit-Out point and
T
press PAUSE (6) . Confirm the time code at this
point ( pg. 24, 25).
2
U
Press REW (2) until the Edit-In point is located,
T
then press PAUSE (6)
3
Press and hold INSERT (w)
control, then press PAUSE (6)
Time Code (min.:sec.) appear and the camcorder
enters Insert-Pause mode.
4
Press START/STOP
• Confirm the insert at the time code you checked in
step 1.
• To pause editing, press START/STOP
again to resume editing.
5
To end Insert Editing, press START/STOP
O
STOP (5) .
NOTES:
● Programme AE with special effects (
used to spice up the scenes being edited during Insert
Editing.
● During Insert Editing, the date and time information
changes.
● If you perform Insert Editing onto a blank space on the
tape, the audio and video may be disrupted. Make sure
you only edit recorded areas.
● During Insert Editing, when the tape moves to scenes
recorded in the LP mode or a blank portion, Insert Editing
stops ( pg. 44).
E
R
T
Y
9
U
2
I
O
P
USING THE REMOTE CONTROL UNIT
.
I
on the remote
T &
. "6w" and the
a
to begin editing.
a
. Press it
a
pg. 16) can be
W
a
s
d
6
f
0
g
4
3
h
w 5 e
j
k
T
l
W
;
, then
EN
29