Related Manuals for CDA HC6211FR
Summary of Contents for CDA HC6211FR
- Page 1 Ceramic Hob Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu www.cda.eu...
-
Page 2: Table Of Contents
Contents: Important Important Notes Using Your Hob Efficient Use Of Your Hob Care And Maintenance Troubleshooting Fitting The Hob How To Install The Hob Mains Electricity Connection Product fiche... -
Page 3: Important
Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model... - Page 4 (EMC) 2014/30/EU. Parts intended to come into contact with food conform to 1935/2004/EC. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EU DIRECTIVE 2012/19/EU. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
- Page 5 • Do not place hot lids flat on the hob top. A “suction” effect could cause damage to the hob. • Do not drag cookware across the hob top: in the long term, this could cause damage to the hob. •...
-
Page 6: Using Your Hob
Using your hob Zones: A. Front left 1.8kW 180 mm D. Back right 1.8kW 180 mm B. Back left 1.2kW 145 mm E. Power indicator C. Front right 1.2kW 145mm F. Residual heat indicators fig. 1 Control knob positions and ideal cooking processes 0. - Page 7 Using Your Hob To switch the hob on • Set the control knob for the desired zone to the required temperature setting. A guide to heat levels and ideal cooking processes is on page 6. The power indicator (E) will illuminate to indicate the zone's usage.
- Page 8 Residual Heat Indicators The hob is equipped with residual heat indicators to warn when any of the zones are still hot to the touch after use. A residual heat indicator will illuminate to show if the relevant zone is approximately 50°c or above.
-
Page 9: Efficient Use Of Your Hob
Efficient Use of Your Hob The hob is equipped with zones designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms. The most efficient use of the hob is shown below, where the pan and zone are correctly chosen. -
Page 10: Care And Maintenance
Care and Maintenance Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. Important: • Steam cleaners must not be used when cleaning this appliance. • You should use a non-abrasive cleaner to clean the hob top. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. - Page 11 2. Check that the mains supply has not been switched off. 3. Check that the fuse in the spur has not blown. In the event of a fault with the hob please advise CDA Customer Care. Contact CDA Customer Care...
-
Page 12: Troubleshooting
11 to arrange a service visit. remedies. Should the above steps not resolve an issue, please contact CDA Customer Care for assistance. Contact details are on page 11. IMPORTANT - PLEASE NOTE: In the event of any breakage, crack or cracking –... -
Page 13: Fitting The Hob
Fitting the Hob Unpacking the hob: Take care not to lose, drop or mishandle any parts. Fitting position of the hob: This appliance must be installed a Installation above a cupboard unit minimum of 50mm from any back wall and a minimum of 55mm away 25mm from any adjacent vertical surfaces, e.g. - Page 14 If fitting a cooker hood above the hob: If a cooker hood is to be installed above the hob, the height of the hood above the hob must be at least 600mm (650mm is recommended) (Fig.5). If the instructions supplied with the hood dictate that the hood must be installed at a height greater than 600mm, Fig.5...
-
Page 15: How To Install The Hob
How to Install the Hob Overall dimensions of the hob: Width: 575 mm Depth: 510 mm Worktop cut-out dimensions: Width: 560 mm Depth: 490 mm 1 - Worktop 1. Make the required hole in the worktop. 2 - Hob seal 3 - Ceramic hob Before doing this, you must check the Fig.6... - Page 16 If fitting the hob into a 28-48mm worktop: The four fixing clips marked with a ‘B’ should be used, as per fig. 9. If fitting the hob into a 48mm+ worktop: The four fixing clips marked with a ‘A’ should be used, as per fig. 8. Position the fixing brackets perpendicularly to the hob’s edge and tighten firmly.
-
Page 17: Mains Electricity Connection
Mains Electricity Connection Warning! This appliance must be earthed. We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. Live L: BN - brown Neutral N: BU - blue Earth PE: GNYE -green/yellow This appliance is intended to be... - Page 18 • This appliance is intended to be connected to the mains supply with a cable of cross sectional area 4mm 2 . • The current rating of the fuse or circuit breaker protecting this appliance should be marked on the socket outlet. •...
- Page 19 Energy E ciency Information Attribute Symbol Value Units CDA model HC6211FR Type of hob Built in Number of cooking zones and/or areas Heating technology (induction cooking Radiant zones and cooking areas, radiant cooking zones cooking zones, solid plates) For circular cooking zones or area: Ø...
- Page 20 Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.eu www.cda.eu...