Summary of Contents for Chamberlain Merlin MS65MYQ
Page 1
gomerlin.com.au gomerlin.co.nz Commander Essential MS65MYQ Sectional Garage Door Opener Installation and Operating Instructions Owners Copy: SAVE THESE INSTRUCTIONS for future reference This manual contains IMPORTANT SAFETY information DO NOT PROCEED WITH THE INSTALLATION BEFORE READING THOROUGHLY...
WARNING! START BY READING THESE IMPORTANT SAFETY INSTRUCTIONS • Failure to comply with the following instructions may result in serious personal injury or property damage. • Read and follow all instructions carefully. • The garage door opener is designed and tested to offer safe service, provided it is installed and operated in strict accordance with the instructions in this manual.
BEFORE YOU BEGIN: 1. Look at the wall and ceiling above the garage door. (The opener and header bracket must be securely fastened to structural supports). 2. Do you have a finished ceiling in your garage? If so, a support bracket and additional fastening hardware (not supplied) may be required.
CARTON INVENTORY Your garage door opener and rail are packed in two seperate cartons. The Commander Essential MS65MYQ opener carton contains the opener, its fitting hardware and accessories. The rail carton contains the rail and some hardware. Rails: Different length rails (2.2 m & 2.4 m) are available for different height doors, ensure you have the correct one. (1) Opener (8) Door bracket (2) Premium+ transmitter (2)
CONTROL PANEL (located under the cover at the rear of the opener) 1. External Accessory Power: 30 Vdc 50 mA available for universal receiver. 2. Terminal Block: used for external accessories (see chart below). Function Colour Polarity Comment E-Serial port Green Serial Communication Input Push button...
ASSEMBLY SECTION Note: The spring must be able to compress and bounce TIGHTEN THE BELT 36 - 38 mm during operation. Final tensioning can be performed after installation if necessary. Over tightening the belt may overload the system and cause excessive wear. 1.Tension the belt by adjusting the nut (1), on the pulley assembly, clockwise until the spring is engaged.
INSTALLATION SECTION Wear protective goggles when working overhead to protect your eyes from injury. Disengage all existing garage door locks to avoid damage to the garage door. To avoid serious personal injury from entanglement, remove all ropes connected to the garage door before installing the opener.
Page 9
POSITION THE OPENER Disengage the trolley mechanism (see section “Operating the manual release”) and slide it back towards the powerhead. Secure the hanging push arm up into the rail assembly temporarily using tape or rope, to avoid a hazard. SECTIONAL DOOR You will need a 50 mm piece of timber or similar spacer to gauge the distance between door and rail.
Page 10
HANG THE OPENER The opener must be securely fastened to a sound structural support above the opener. fig.1 1.Postion the opener as in the previous step. Check the rail is centred over the door. Ensure the rail brackets (fig.1) is on the Powerhead end of the rail in a position as close to the opener as possible (X).
Make sure the garage door is fully closed. Pull the manual release ATTACH DOOR ARM TO TROLLEY cord to disengage the trolley. Slide the trolley to around 300 mm from Fig. 1 Fig. 2 the header bracket. 1.The straight door arm is already preassembled to the trolley. 2.Install the curved arm onto the door bracket using the Clevis pin (2) (item 6 in the Hardware Provided - Section 5) and R-Clip.
ADJUSTMENT SECTION Travel limits regulate the points at which the door will stop PROGRAM THE TRAVEL LIMITS AND FORCE SETTINGS Without a properly installed safety reversal when moving UP or DOWN. The travel limit buttons are located system, persons (particularly small children) under the access cover on the rear panel (figure 1).
Page 13
TEST THE SAFETY REVERSE SYSTEM The safety reverse system test is important. Garage door must reverse on contact with a 40 mm obstacle laid flat on the floor. Failure to properly adjust opener may result in serious personal injury from a closing garage door.
THE PROTECTOR SYSTEM (IR BEAMS) (OPTIONAL) NOTE: This accessory must be used for all installations where the closing force as measured on the bottom of the door is over 400 N (40 kgf). To prevent entrapment, install The Protector System™ (IR Beams) no higher than 100 mm above SPECIAL NOTE: Merlin strongly recommends that The the floor.
TIMER TO CLOSE FEATURE (TTC) Door may operate unexpectedly, therefore do not allow anything to stay in the path of the door. figure 1 The Timer to Close feature requires The Protector System (IR Beams) to be installed. Indicator LED Operation: Door Fully Closed This feature allows the door to automatically close from a fully...
INSTALL WARNING LABELS figure 1 For Service Call RISK OF ENTRAPMENT Installation Date Repeat Safety Reverse Test monthly. Door 114A3361 must reverse on contact with a 40mm obstacle For Service Call placed on the floor. Make necessary adjustments. AUTOMATIC DRIVE: Keep away from the area of the door since it may operate unexpectedly.
WIRELESS PROGRAMMING (OPTIONAL ACCESSORIES) Activate the opener only when door is in full view, free of obstruction and properly adjusted. No one should enter or leave garage while door is in motion. Do not allow children to operate push button(s) or transmitter(s).
MAINTENANCE AND CARE OF YOUR OPENER Battery of the transmitter: USING YOUR OPENER REPLACE BATTERIES IN TRANSMITTERS 1. Your opener can be activated by any of the following devices: • Opener control panel: Up and Down Buttons and Green O.S.C. The batteries in the transmitter have an extremely long life.
E1702M 760E 774ANZ 827AU NOTE: Use of any Chamberlain Group accessories are approved to use with this opener. This includes genuine Merlin accessories. Generic compatible accessories are NOT approved for use with this opener RAIL HARDWARE 002A1800 Trolley with rope &...
REPLACEMENT PARTS If the supply cord is damaged, it must be Power Cord replaced by the manufacturer, its service 026B0181 agent or similarly qualified persons in order to avoid hazard. 041A0046 Logic Board / PCB Housing / Control Cover (assembly) 041A4004 Passpoint Assembly...
TROUBLE SHOOTING 1. Opener doesn't operate from either door control or 7. Door opens but won't close: transmitter: • Check The Protector System™ (IR Beams) (if you have • Does the opener have electric power? Plug lamp into installed this accessory). If the light on The Protector outlet.
Page 22
DIAGNOSTIC CHART Your garage door opener is programmed with self-diagnostic capabilities. The UP and DOWN arrows on the garage opener flash the diagnostic codes. DIAGNOSTIC CODE SYMPTOM POSSIBLE RESOLUTION UP Arrow DOWN Arrow Flash(es) Flash(es) The garage door opener will not The Protector System™...
Warranty Conditions Except as set out in the Australian Consumer Law (being Schedule 2 of the It is a condition of this Chamberlain Limited Warranty that the Unit is sold, Competition and Consumer Act 2010) (as amended, consolidated or replaced):...