Operation - Ryobi RVC-1430PPT-G Owner's Operating Manual

Insert the handle into the slots on the power head and
pressure into place (Fig. 6).
For dry vacuum cleaning, install the supplied cartridge
filter and dust bag (Fig. 7, Fig. 8).
For wet vacuum cleaning, install the supplied foam filter
(Fig. 9)
Replace the top section on the tank (Fig. 10).
Align the top section with the clamps and snap into place
by applying pressure until clamps click (Fig. 10).
Insert the large end of the hose into the front inlet of the
tank and turn to lock (Fig. 11).
Fit the required accessory on to the suction tube (Fig. 12).

OPERATION

DRY VACUUMING
WARNING
Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
The use of an incorrect dust bag will invalidate the
warranty.
Ensure that the power cord is disconnected from the
outlet.
Ensure that the cartridge filter is completely mounted.
Ensure that the filter is inserted all the way. (Fig. 13)
Verify that the dust bag is installed to the inside of the
tank (Fig. 8).
Replace the top section on the tank, and secure it in
place using the clamps (Fig. 10).
Insert the larger end of the hose into the front inlet on the
tank and lock it in place. Push the required attachment
on to the free end of the hose or extension (Fig.12).
Plug the power cord in to the power outlet.
Turn the motor on by flipping the switch to the
(Fig. 14).
Once you have finished vacuuming, flip the switch to the
position and unplug the power cord from the power
outlet. (Fig. 15)
WARNING
DO NOT USE THE CARTRIDGE FILTER FOR WET
OR SHARP MATERIALS.
DO NOT USE DUST BAG FOR LIQUID VACUUMING.
WET VACUUMING
WARNING
Ensure that you read, understand, and apply the
safety instructions.
Reminder: DO NOT vacuum hazardous substances.
Ensure that the power cord is disconnected from the
power outlet.
Ensure that the tank is clean and free of dust and dirt.
Remove the cartridge filter and dust bag, and install a
foam filter over the filter basket and place the top section
back on the tank (Fig. 9).
DO NOT use the cartridge filter for wet or sharp materials.
Fit the desired nozzle to the vacuum hose (Fig. 12).
Ensure that the switch is in the
plugging the power cord into the power outlet.
Turn the motor on by flipping the switch to the
(Fig. 14).
After use, flip the switch to the
unplug the power cord, then empty and dry the tank
(Fig. 16, Fig. 17).
The foam filter must be removed after wet vacuuming,
and a cartridge filter must be installed before dry
vacuuming again.
IMPORTANT!
When vacuuming large quantities of liquids, do not immerse
the nozzle completely in the liquid; leave a gap at the tip of
the nozzle opening to allow air inflow.
The machine is fitted with a float valve that stops the
suction action when the container reaches its maximum
capacity. You will notice an increase in motor speed.
When this happens, turn off the machine, disconnect from
power supply, and drain the liquid into a suitable receptacle
or drain. To continue vacuuming, refit the container with the
drain cap. After wet vacuuming, turn the machine off and
remove plug from power supply.
Empty the container, clean and dry the inside and outside
before storage.
CONNECT ELECTRICAL APPLIANCES
Connect electrical appliance with Power Take Off on the
Shopvac.
Switch on electrical appliance. Only connect electrical
position
appliances with a maximum power rating of 1000W.
Flipping the switch to the
Once the electrical appliance has been switched off, the
vacuum cleaner switches off following a time lapse.
BLOWER OPERATION
This Wet/Dry Vac has blowing capabilities.
To use the blower feature follow the instructions listed.
Always wear safety goggles before using blower.
Keep bystanders clear from blowing debris.
3
position before
position
position (Fig. 15) and
WARNING
position (Fig. 18).
WARNING
WARNING