Acer X1130P Service Manual
  1. Manuals
  2. Brands
  3. Acer Manuals
  4. Projector
  5. X1130P Series
  6. Service manual

Acer X1130P Service Manual

Hide thumbs Also See for X1130P:
Table of Contents

Advertisement

Quick Links

See also: User Manual
Projector Service Manual
Model : X1130P, X1130PA, X1230PK,X1230P,
X1230PA, X1237
Version: Rev3
First Edition (Jul. 2009)
RESTRICTIONS ON USE OF MATERIALS:
1

Advertisement

Table of Contents
loading

Related Manuals for Acer X1130P

Summary of Contents for Acer X1130P

  • Page 1 Projector Service Manual Model : X1130P, X1130PA, X1230PK,X1230P, X1230PA, X1237 Version: Rev3 First Edition (Jul. 2009) RESTRICTIONS ON USE OF MATERIALS:...

  • Page 2: Table Of Contents

    REVISION LIST ... 3 CHAPTER 1 SYSTEM SPECIFICATION ... 4 Product Specification ... 4 Electrical Specification... 11 Power Supply Specification...15 System Block Diagram ... 16 Product Overview ... 17 CHAPTER 2 SYSTEM UTILITIES... 21 Firmware Upgrade SOP... 21 Method to enter factory menu ... 29 EDID Upgrade SOP ...

  • Page 3: Revision List

    Revision List Release Version Date Rev0 2009.07.16 First Release Rev0 2009.07.20 Modify FRU List—service lamp P/N (P.5) Modify SPEC : Projection Offset = 120% ±5% Rev0 2009.07.27 Add X1230PK different part : (1) Ch1- SPEC, (2) Ch3- Disassembly process, Module Assembly Key Point Rev1 2009.07.29 (3) Ch4- alignment procedure...

  • Page 4: Chapter 1 System Specification

    Chapter 1 System Specification Product Specification Optical Performance Image Quality Mechanical Specification Packaging Thermal Specification Environmental Regulatory Reliability Power Requirements Panel Specification 10.0 Compatibility 11.0 12.0 Image Interface 13.0 Control Interface User Interface 14.0...
  • Page 5 Distortion 2.4 Projection Offset 2.5 Focus Range 2.5.1 Visible Range Tested under 60” (diagonal) image size with Wide projection lens position unless other specified. X1130P/X1130PA/X1230P : Minimum 2000 Lumens X1230PK/X1230PA : Minimum 1840 Lumens X1237 Minimum 2400 Lumens Minimum 55% Minimum 75% 0.5~2...
  • Page 6 (1) If pattern can be uniformly focused (not worse than Limit Sample), then pass! (2) If it’s difficult to judge, then check 2.6.2 X1130P : Defocus: R<=3.0; G<=3.0; B<=3.0 pixel Flare: R<=3.5; G<=3.5; B<=3.5 pixel Slight flare is not counted as flare.
  • Page 7 X1130PA X1230PK/X1230PA : 0.55” XGA 2xLVDS Series 450 Super value DMD X1230P/X1237:0.55” XGA 2xLVDS Series 450 DMD X1130P/X1130PA : H: 800 X V: 600 X1230PK/ X1230P / X1230PA / 30 Bits (1.07 Billion Colors) Adhere to “Electrical Specification” section PC Compatible 640X480 1024X768, compressed 1600X1200;...
  • Page 8 15 pin D-Sub (Female) x 1 Y: Luminance amplitude 1.0 V PbPr/C : Chroma amplitude 0.7 V X1130P : None X1130PA/X1230PK/X1230P/ X1237/ X1230PA 15 pin D-Sub (Female) x 1 (Only support D-sub 1) G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75Ω...
  • Page 9 Lamp hour = [Hour used in Normal Mode] + 3/4 *[Hour used in Eco. Mode] CC1/CC2/CC3/CC4 (Running change to phase-in X1130P/X1130PA /X1230PK / X1230P/ X1237/ X1230PA MP stage) After turn off projector, there is 120 seconds called “Instant On stage”. At this stage, user can turn on the projector. Aftet this stage, projector will cooling for 20 seconds, and all keypads are not allowed to operate.
  • Page 10 Reminder screen : Pop-up screen and appear 10 sec in the center of the screen. End-users can press Menu to − exit within 10 sec. − (1) When 3D enable, this screen will appear after exit OSD menu. − (2) There has reminder screen if 3D still enable when power on projector. −...

  • Page 11: Electrical Specification

    Electrical Specification 1. Timing Table The PC timing is as following: Resolution Mode VGA_60 VGA_72 640 x 480 VGA_75 VGA_85 VGA_70 720 x 400 VGA_85 SVGA_56 SVGA_60 800 x 600 SVGA_72 SVGA_75 SVGA_85 XGA_60 XGA_70 1024 x 768 XGA_75 XGA_85 SXGA_70 1152 x 864 SXGA_75...
  • Page 12 800 x 600 SVGA_120 1024 x 768 XGA_120 Note：3D timing will phase in after MP when 3D function ready YPbPr support timing is as following: Signal format 480i(525i)@60Hz 480p(525p)@60Hz 576i(625i)@50Hz 576p(625p)@50Hz 720p(750p)@60Hz 720p(750p)@50Hz 1080i(1125i)@60Hz 1080i(1125i)@50Hz 1080P@60HZ 1080P@50Hz Video, S-Video support timing is as following: Video mode NTSC SECAM...
  • Page 13 SCLDATA Amplitude, low level Amplitude, high level Amplitude Amplitude CVBS Amplitude, total (video+ Luminance sync) Amplitude, video Amplitude, sync Impedance CVBS Amplitude Chroma Impedance Audio Impedance (audio in) (for Amplitude (audio in) X1130PA / Bandwidth X1230PK/ X1230P/ S/N Ratio X1237/ Total Harmonic X1230PA) Distortion...
  • Page 14 Control Port Mini USB TYPE B (for X1130PA 4. Functionality External Message indicator Message D-sub /Composite Video /S-Video Searching Input Not Supported Lamp is approaching the end of its useful life in full power operation. Replacement suggested! Description /X1230PK/ X1230P/ X1237/ Description Vbus The system does not detect the signal...

  • Page 15: Power Supply Specification

    Power Supply Specification 1. Input Power Specification Specification Input Voltage Range Frequency Range Power Consumption Regulation Efficiency 2. Output Power Requirement The power supply can provide DC 12V output as below： Voltage Regulation +12 V ±5 % +5 V ±5 % The power supply can provide DC 380V output as below：...

  • Page 16: System Block Diagram

    System Block Diagram...

  • Page 17: Product Overview

    Product Overview...

  • Page 21: Chapter 2 System Utilities

    Chapter 2 System Utilities Firmware Upgrade SOP Basic Operating Standby Mode： ： ： ： When standby mode, system power consumption will be less than 1 Watt. If user wants to enter this mode, user can just plug in power cord. Power, Lamp, Temp LED will show Red for 1 sec then power LED show red continuously as the figure shown.
  • Page 22 DLP Composer LIte Installation Process (1) Installation 1. Double click the Setup file for DLP Composer Lite(to unzip “TI Download Tool V1.1 (for DDP243x).rar” to start to install program. 2. When the Installation Wizard appears, click “Next”. 3. Select to accept the License Agreement, than click “Next” 4.
  • Page 23 Note: The default installation directory is: C:\Program Files\DLP Composer Lite9.2 If you want to install to a different directory (perhaps alongside a prior release of DLP Composer™ Lite), click the "Browse" button on the "Select Features" page. 5. When finishing installation, click “Finish”, and then restart your computer to complete the installation process.
  • Page 24 (2) Setting for your first use Select Library: 1. When start to use this program to download at first time, you need to check if the library folder is existed under the path of Library. Click “ “ “ “ Browse Click Click Click...
  • Page 25 Set communication (for download by RS232): 1. Select “Edit”->”Preference”. Select “Communications”-> “Serial Port” -> ”Config”. 3. Make sure the settings are the same as below figure-> Click ”OK”. 4. Click ”OK”.
  • Page 26 (1) Download Procedure Notice: for X1130P, since the Main board P/Ns are different in with-3D and without-3D function SKUs, need to download correct FW into corresponding Main board. How to download Hardware required 1. Standard RS232 Download cable 2. Personal computer or laptop computer Software required 1.
  • Page 27 Click on “Flash Loader” and browse the image file (new version firmware) Select Complete Image Download, and make sure to check “Skip Boot loader area (32KB)”...
  • Page 28 Press “Reset Bus” and check the status which should show “Bus Reset” Press “Start Download” to begin update new firmware. Press “Yes” to continue. (when download new firmware and power LED will show purple.)

  • Page 29: Method To Enter Factory Menu

    10. Wait till composer lite notice download complete. When download complete, LED signal on projector will show standby status. Method to enter factory menu Press keypad Power and image will show Power Down OSD function Press keypad Left twice then press Menu, then enter the Factory mode. Step 1 Step 2...

  • Page 30: Edid Upgrade Sop

    EDID Upgrade SOP Equipment List 1. PC : with parallel (printer) port 2. EDID Board 3. Printer cable : 25pin male-female (connect PC to EDID board) 4. D-sub cable* : with full 15pin (connect EDID board to Projector) 5. HDMI cable*(connect EDID board to Projector) 6.
  • Page 31 Software Installation, Un-installation : Unzip the “Q-EDID” program files in the same directory. Install Q-EDID tool : Execute “Install Q-EDID.BAT” to install & register EDID Board into the computer. Un-install Q-EDID tool : If you want to uninstall this tool, execute “Uninstall Q-EDID.BAT”, then it will remove EDID Board from the computer.
  • Page 32 Step2 Step4 (3) Read EDID: • Read D-SUB/DVI EDID: 1. EDID Type Selection : Choose ‘‘EDID 128 Bytes’’ 2. Read EDID : Click “Read EDID”. 3. While complete, it will show message’’ Read EDID OK… ‘’, and the read-out DDC will show in the table in program.

  • Page 33: Serial Number Upgrade Sop

    Serial Number Upgrade SOP Hardware required Standard RS232 Download cable Personal computer or laptop computer Software required 1. Acer_Service_Tool(Data)_3.1.exe When need to use this Serial Number Upgrade program: When it’s time to replace Main board for repair, it’s necessary to rewrite original S/N and some adjustment values into new Main board by the following process.
  • Page 34 6. Click “Save” to save data into the assigned file name. 7. Change new Main board: (1) Unplug power cable and RS232 cable from projector, and change new Main board into Projector. (2) After changing Main board, reconnect power cable and RS232 cable into Projector. 8.

  • Page 35: How To Change Model Name

    How to Change Model name (Only for X1230P/X1230PA/X1237) Since X1230P/X1230PA/X1237 use the same Main board, after replacing new Main board, it’s necessary to change model name: 1. Enter Factory menu. 2. Go to Page2 (as below figure). 3. Default Model name is “X1230P”. When change Main board on X1230PA or X1237, please press right/left key to choose correct model name.

  • Page 36: Chapter 3 System Disassembling And Replacement

    IR sensor wire. Take off the case left module and the front FRONT case module IR BD For X1130P: (1) Take off screws: For X1130P : Disassemble the screw*2(STAND OFF XH4#-40*6L). For X1230PK : For X1230PK: Disassemble the screw*4(STAND OFF XH4#-40*6L).
  • Page 37 Disassemble the screw*5(M3*5L), and take off the M/B shielding. (1)Take off the long wire (one of twin fan wire), then disassemble the twin fan. (2)Take off the twin fan wire from M/B. take off this long wire first C/W FPC wire (1)Take off the C/W FPC wire, blower fan wire, C/W sensor wire,...
  • Page 38 (1)Disassemble the screw*2(M3*6L), and take off the lamp door. (2)Disassemble the screw*1(M3*4L) and lamp wire, and take off the lamp module. (1)Disassemble the screw*3(M3*8L). (2)Disassemble the grounding screw*1(M4*6L), and take off the Power B/D SHD. screw*1 Disassemble the wire*2 and screw*1 (M3*7L), and take off the power BD and ballast Mylar.
  • Page 39 Disassemble the screw*3(M3*7L), and take off the OPT eng . Disassemble the screw*2, the ballast BD, and wire*3(M3*5L). Take off the push button . ring focus (1)Take off the gasket*2. (2)Disassemble the focus ring. Take off th LENS screw*3(M3*4L) and Ring Zoom and Ring Focus screw*2(M2*3.5L)
  • Page 40 Disassemble the screw*4(M3*7.5L), and take off the HSINK and DMD chip with Chip BD. (1)Disassemble the baffle DMD. (2)Disassemble the screw*3(M3*4L) and take off the CW baffle DMD module. Rotate to open the switch on socket, and take off the DMD chip.

  • Page 41: Module Assembly Key Point - Optical Engine

    Module Assembly Key Point - Optical Engine 1. Light Pipe Module assembly and overfill alignment 1.1 Assembly LP Module to HSG DMD (1) Assembly two Overfill adjustment screws to HSG DMD (Fig. 1-1). ** Adjustment criteria refer to below item (2) Assembly “Clip LP”...
  • Page 42 1. Press down the Clip 2. Insert the LP Module LP Datum of DMD HSG Fig. 1-3 Fig. 1-4 Overfill adjustment screws...
  • Page 43 1. Place Clips on BKT surface Pre assemble this screw not over the bottom surface. 3. Lock screw 2. Push Baffle LP to hook DMD HSG Fig. 1-5-1 Fig. 1-6 Fig. 1-5-2 Pre assemble this screw not over the side surface.
  • Page 44 2. Assembly FM Module: Place FM on “HLD FM” surface(Fig. 2-1) and use “Clip FM” to fix FM(Fig. 2-2). Touch the side surface Fig. 2-1 3. Assembly HSG ILL Module: 3.1 CM Assembly Insert “Clip CM Side” first, and then place “Clip Front CM” to fixed-shaft of ILL SUB before locking screw (Fig.
  • Page 45 Datum3 Datum1 Datum2 Fig. 3-3 Clip UP CM Fig. 3-4 Fig. 3-5 Sponge Fig. 3-6...
  • Page 46 4. AL, HSG ILL and HSG DMD Assembly: 4.1 Placed “AL” on the “HSG DMD”. The “raised surface” of “AL” shall toward “DMD direction” (Fig. 4-1). 4.2 To assemble ”HSG ILL SUB Module” with “HSG DMD” and cover over on “AL” and the then lock with screws (Fig.
  • Page 47 5. DMD and Chip B/D Module: 5.1. Judge Chip B/D and DMD alignment keying first (Fig. 5-1, 5-2). 5.2. Alight keying and Assemble DMD to Chip B/D (Fig. 5-3). 5.3. Push DMD slightly and use screwdriver rotate clockwise button to lock (close notation) DMD on Chip B/D (Fig.
  • Page 48 6. Assembly Optical Engine: 6.1 Assemble “BKT Link Lamp & CW shield” on “DMD HSG” and then lock with screws well (Fig. 6-1). 7. Assembly OP ENG 7.1 Assemble “Baffle DMD” to “HSG DMD” (Fig.7-1). 7.2 Assemble “Sponge DMD” to “HSG DMD” (Fig.7-1). 7.3 Assemble Chip B/D Module to “HSG DMD”...
  • Page 49 Fixed shafts of DMD HSG Fixed holes of DMD 7.4 Assemble Thermal Pad & Gasket Hest-sink then place contact DMD (Fig. 7-3). Pre-fastening Sequence: [ 1 ] - [ 2 ] - [ 3 ] - [ 4 ]. Fastening Sequence: [ 2 ] - [ 1 ] - [ 4 ] - [ 3 ]. iii.
  • Page 50 Screw ○ ○ Gasket ○ ○ Fig. 7-3 7.5 Assemble “CW Module” to “DMD HSG” and lock with screws well (Fig.7-4). Screw Fixed shafts of DMD HSG Fig.7-4...
  • Page 51 7.6 Assemble “Mylar Antidust” well (Fig. 7-5). Fixed shafts of DMD HSG Mylar Antidust Fig.7-5 7.7 Assemble PL LENS” and lock with screws well (Follow MP522 assembly) (Fig. 7-6). Screw Fig. 7-6...
  • Page 52 7.8 Assemble “Ring Zoom” and lock with screws well (Fig. 7-7). 7.9 Assemble “Ring Focus” (Fig. 7-8). Insert and push Ring Focus until fix on the pin of LENS Screws* 2PCS Fig. 7-7 Fig. 7-8...
  • Page 53 7.10 Assemble Lamp Module to “BKT Link Lamp” and then lock with screw well (Fig. 7-10, Fig. 7-11). Screw Fixed shafts Fig. 7-10 Fig. 7-11...

  • Page 54: Module Assembly Key Point - Mechanical

    Module Assembly Key Point – Mechanical 1. Assemble Lower case This module includes LC*1pcs,Sponge*1pcs， SHD LC*1pcs，Screw*3pcs Sponge pasted as lower case, must closed to hook. Screw*3pcs...
  • Page 55 2. Lower case and Adjust foot Spring no bend 3. Blower module assemble with LC This step includes blower module*1pcs and screw2pcs 4. Ballast wire Alignment dressed It needs screw*2pcs Screw*2pcs...
  • Page 56 The EMI cord will behind the mylar-ballast screws*2 The wire needn’t around this rib. Ballast to Lamp wire should align in to this groove...
  • Page 57 5. Mylar-ballast and blower module assembly 6. Lamp box assemble with lower case Rib This step needs screw*2pcs to fix assembly lamp-box with LC! First: assy Blower module Second: assy Mylar Ballast Ballast to Lamp wire also should align in to Mylar Ballast groove...
  • Page 59 7. PWR BD board must check the height of soldering tin This step needs check connector and boss height. A piece of screw*1pcs needs dress. Screw*1pc 8. The assembly of OPE and LC This step needs screw/8F.VA564.7R0*3pcs to tighten. And the sequence needs obey according to picture. For EMI, the rubber power is necessary.
  • Page 60 Screw*3pcs Rubber Power 9. Fix PWR between SHD-PWR and LC Assemble SHD-Power This assembly includes SHD/3K.0R501.031*1pcs, saddle/4B.0R501.001*1pcs and a piece of mylar/4K.0R501.001*1pcs. This step needs screw*4pcs to tighten parts.
  • Page 61 Screw Screw Confirm the position of EMI cord right.
  • Page 62 10. Main BD assembly and connector position Need check the connectors OK completely This step adds sponge*1pcs...
  • Page 63 11. Assemble Main BD SHD CW sensor board wire and CW FPC alignment Please align the CW FPC, then put the sensor wire into the saddle together. Second, screw*4pcs will be done firstly. The add screw*1pcs and clip*1pcs Finally, assemble fan and fix the wire by clip. First Screw*4pcs Screw*1...
  • Page 64 12. Front IR wire to MB alignment Front IR wire should align in to these grooves...
  • Page 65 13. Stick the leakage Mylar Align IR-holder side (A and B) paste mylar 14. Dress the Inlet-case, outlet-case and rear-case It is necessary to confirm the position of SHD when assembling the rear-case!
  • Page 66 Please attention a piece of Mylar on Rear-case Refer to its assembly as follows: Shield K-LUCK light leakage Action: add new Mylar at rear case Align this side Align this side No adhesive area...
  • Page 67 15. Assembly side case Assy case-inlet: Assy case-outlet: (For X1130PA / X1230PK/ X1230P/ X1237/ X1230PA) It includes Case-outlet*1pcs, sponge*3pcs, speaker*1pcs and screw*2pcs.
  • Page 68 For this module, pay attention to the first position of sponge and the orientation of SPK. 16. Assembling the case-upper Align this side pasted sponge Push bkt-key and key closed Add washer and screw to hold key-bkt...
  • Page 69 Add a piece of sponge for light leakage 17. Ballast to lamp wire alignment Lamp box should close up the opening of lower case Lamp connector assemble with rib...
  • Page 70 18. Lamp Door screw assemble sequence 19. Protect firm at upper case must have no bubble Must use a scraper to removed the bubbles. 20. Add a piece of Mylar for light leakage...

  • Page 71: Chapter 4 Troubleshooting

    Chapter 4 Troubleshooting System Analysis...

  • Page 72: Optical Problems Checking Items

    Optical Problems Checking Items Item Brightness Uniformity FOFO Contrast ANSI Contrast Color Color Uniformity Blue Edge Blue/Purple Border Focus Dust Horizontal/Vertical Strips Pixel Fail Trouble Shooting Guide 1. Change lamp 1. Change lamp 1. Check ADC calibration 2. Check user’s menu brightness & contrast are default 3.
  • Page 73 “Blue Edge” Trouble Shooting: I. Re-adjust “Overfill” first. For Overfill Re-adjustment: i. Those 2 Adjustment Screws must be released for around 2 mm first. ii. Alignment Sequence: To adjust “Horizontal Adjustment Screw” firstly, then “Vertical Adjustment Screw”. Refer to below Figure. (2) Overfill Vertical Adjustment Screw II.

  • Page 74: Power Supply Problems Checking Flow

    Power Supply Problems Checking Flow...

  • Page 75: Led Messages Definition

    LED Messages Definition External Status indicator LED Name Power LED Lamp Status LED Temperature Status LED Lamp_LED Power Plug Flash ON to OFF Standby Power button ON Lamp retry Cooling state Power button OFF: Cooling completed; Standby Mode Firmware Download Thermal sensor error (T2 8 ) (Lamp...

  • Page 76: Error Count Messages Definition

    Error Count Messages Definition Error Count Definition LAMP Fail error LAMP OFF FAN 1 Speed Error LAMP FAN SPEED ERROR FAN 2 Speed Error BALLAST FAN SPEED ERROR SPEED OVER ± 20% FAN 3 Speed Error BLOWER FAN SPEED ERROR SPEED OVER ± 20% Sensor 1 Open Error Main Board SENSOR ERROR Sensor 2 Open Error...

  • Page 77: Rs232 Connection

    RS232 Connection 1. Connection: Below shows the illustration of connection between PC and Projector. <CAUTION> Make sure that your computer and projector are turned off before connection. Power on the computer first, and then plug the power cord of the projector. (It may cause Com port incorrect function, if you do not follow this instruction) Adapters may be necessary depending on the PC connected to this projector.
  • Page 78 Interface Settings RS-232 protocol Baud Rate Data Length Parity Check Stop Bit Flow Control Command Category Refer to Appendix A 115200 bps 8 bit None 1 bit None...

  • Page 79: Adjustment / Alignment Procedure

    Adjustment / Alignment Procedure Content : 1. Color Wheel Delay Alignment 2. Overfill adjustment 3. PC Alignment Procedure 4. Keystone Calibration...
  • Page 80 1. Color Wheel Delay Alignment Procedure: Enter Factory Mode Enter Block 1 Change CW Delay by adjusting the following gray pattern to smooth 32 Gray pattern...
  • Page 81 2. Overfill adjustment (Blue Edge adjustment) 1. “Full White Pattern” is suggested for this alignment. 2. Adjust 2 LP-alignment Screws (upper side / lower front side of Optical Engine) behind Color Wheel. 3. Alignment Criteria is to adjust these 2 screws until “No Dark Edges” and “ No Shadows”...
  • Page 82 Connect power cord, D-sub cable, and pattern generator into projector Light on projector Change Timing and pattern of pattern generator Timing: For X1130P/X1130PA : 800*600 @60Hz (SVGA) For X1230PK/ X1230P/ X1230PA/ Pattern: pattern 1 Press keypad “Resync” to confirm image frame is correct...
  • Page 83 4. Keystone Calibration Condition：Horizontal plane(0∘) 1. Make projector be horizontal 2. Enter factory menu 3. Enter into Block in factory menu 4. Select item “AutoKeystoneCal” 5. Press key Left or Right to do auto calibration ∘ 6. Finish 0 calibration and bellow items will show data AutoKeystoneXCal: ≦...

  • Page 84: Chapter 5 Fru List

    Chapter 5 FRU List Exploded Diagram Module 1 – Total Exploded View...

  • Page 86: Module 2 - Assy Upper Case

    Module 2 – ASSY UPPER CASE...

  • Page 87: Module 3 - Assy Lower Case

    Module 3 – ASSY LOWER CASE...

  • Page 88: Module 4 - Assy Front Case

    Module 4 – ASSY FRONT CASE...

  • Page 89: Fru List

    1237 X1130P/X1130P A/X1230PK/X12 BOARD 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 BOARD 30PA/X1230P/X 1237 PARTNAME ACER PART NO. Projector Remote Control Qisda RC Q5 layout (25 VZ.K0300.002 keys w/o Laser, w/o Mouse, with PgUp/PgDn) Projector Remote Control Qisda RC Q3 layout (25 VZ.K0300.001...
  • Page 90 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237...
  • Page 91 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 CABLE 30PA/X1230P/X 1237 CASE/COVER/B X1130P RACKET ASSEMBLY CASE/COVER/B X1230PK RACKET ASSEMBLY X1130PA/X1230 CASE/COVER/B PA/X1230P/X12 RACKET ASSEMBLY X1130P/X1130P CASE/COVER/B A/X1230PK/X12 RACKET 30PA/X1230P/X ASSEMBLY 1237 X1130P/X1130P CASE/COVER/B A/X1230PK/X12 RACKET 30PA/X1230P/X...
  • Page 92 X1130P/X1130P CASE/COVER/B A/X1230PK/X12 RACKET 30PA/X1230P/X ASSEMBLY 1237 X1130P/X1130P CASE/COVER/B A/X1230PK/X12 RACKET 30PA/X1230P/X ASSEMBLY 1237 X1130P/X1130P CASE/COVER/B A/X1230PK/X12 RACKET 30PA/X1230P/X ASSEMBLY 1237 X1130P/X1130P DIGITAL LIGHT A/X1230PK/X12 DEVICE 30PA/X1230P DIGITAL LIGHT X1237 DEVICE X1130P/X1130P A/X1230PK/X12 DIGITAL LIGHT 30PA/X1230P/X DEVICE 1237 X1130P/X1130P DIGITAL LIGHT...
  • Page 93 X1130P/X1130P DIGITAL LIGHT DEVICE X1230PK/X1230 DIGITAL LIGHT DEVICE DIGITAL LIGHT X1230P/X1237 DEVICE X1130P/X1130P A/X1230PK/X12 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 30PA/X1230P/X 1237 X1130PA/X1230 PK/X1230PA/X1 SPEAKER 230P/X1237 X1130P/X1130P A/X1230PK/X12 MISCELLANEO 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 MISCELLANEO 30PA/X1230P/X 1237 X1130P/X1130P A/X1230PK/X12 JIG BOARD 30PA/X1230P/X 1237...

  • Page 94: Appendix A - Code List: Ir / Rs232 / Ddc Data

    Appendix A - Code List: IR / RS232 / DDC Data 1. Remote Control Code: IR setting value Frequency: 38kHz Protocal: NEC format b. IR command code X1130P: Customer code： ： ： ： 0813...
  • Page 95 X1130PA/ X1230PK/ X1230P/ X1230PA/ X1237: Customer code： ： ： ： 0813...

  • Page 96: 2. Rs-232 Command Code

    2. RS-232 Command Code General command type (Projector ‘receives’ commands) Code (character) OKOKOKOKOK Power On * 0 IR 001 Power On * 0 IR 002 Power Off * 0 IR 004 Keystone * 0 IR 006 Mute * 0 IR 007 Freeze * 0 IR 008 Menu...
  • Page 97 * 0 IR 044 Keystone Left * 0 IR 045 Keystone Right * 0 IR 046 Zoom * 0 IR 047 e-Key * 0 IR 048 Color RGB * 0 IR 049 Language * 0 IR 050 Source HDMI General command type (Projector ‘transmits’ commands) Code (character) Model XXXXXXXX Return the Model name Return...

  • Page 98: Ddc Data

    3. DDC Data X1130P EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 06 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23...
  • Page 99 Max Horiz. Freq - 93 kHz Pixel Clock - 170 MHz GTF - Not Used ______________________________________________________________________ (5AH-6BH) Detailed Timing / Descriptor Block 3: Monitor Name: X1130P ______________________________________________________________________ (6CH-7DH) Detailed Timing / Descriptor Block 4: Monitor Serial Number: K06050018401 (7EH) Block No: No Extension EDID Block(s)
  • Page 100 X1130PA EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 09 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23 20 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C0 30 | 81 00 95 00 B3 00 A0 0F 20 00 31 58 1C 20 28 80 40 | 14 00 00 00 00 00 00 1E 00 00 00 FD 00 30 78 1F...
  • Page 101 Standard Timing ID 5: 1280 x 720 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 800x600 Pixel Clock: 40.00 MHz ______________________________________________________________________ Horizontal Image Size: 0 mm...
  • Page 102 X1230PK EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 03 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23 20 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C0 30 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F...
  • Page 103 Standard Timing ID 4: 1280 x 1024 @60Hz Standard Timing ID 5: 1280 x 720 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz...
  • Page 104 X1230PA EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 10 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23 20 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C0 30 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F...
  • Page 105 Standard Timing ID 5: 1280 x 720 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz ______________________________________________________________________ Horizontal Image Size: 0 mm...
  • Page 106 X1230P EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 11 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23 20 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C0 30 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F...
  • Page 107 Standard Timing ID 5: 1280 x 720 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz ______________________________________________________________________ Horizontal Image Size: 0 mm...
  • Page 108 X1237 EDID ： ： ： ： EDID Block 0, Bytes 0-127 [00H-7FH] Block Type: EDID 1.3 ________________________________________________________________ 0 | 00 FF FF FF FF FF FF 00 04 72 05 12 01 00 00 00 10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 23 20 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C0 30 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 88 40 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F...
  • Page 109 Standard Timing ID 5: 1280 x 720 @60Hz Standard Timing ID 6: 1280 x 800 @60Hz Standard Timing ID 7: 1440 x 900 @60Hz Standard Timing ID 8: 1680 x 1050 @60Hz ______________________________________________________________________ (36H-47H) Detailed Timing / Descriptor Block 1: 1024x768 Pixel Clock: 65.00 MHz ______________________________________________________________________ Horizontal Image Size: 0 mm...

This manual is also suitable for:

X1130paX1230pkX1230pX1230paX1237

Table of Contents