Page 1
Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.com in English, or in specific languages using the Regional selection box in the upper right corner of our website.
Page 2
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the follow- ing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 3
Important Safety Instructions Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.
Page 4
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Proposed Maximum Substance...
Page 5
Product Registration To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form.
Table of contents Important safety Operating in a high altitude environment ............36 instructions .......2 Using the CEC function..... 37 Introduction......4 Using the 3D functions ...... 37 Controlling the projector through Projector features ......... 4 a LAN environment ......38 Shipping contents.........
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions Please read this manual before you operate your projector.
Page 8
Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications. •...
Controls and functions Projector Lens shift wheel Lamp indicator light Focus and Zoom rings Power indicator light Temperature indicator light • Enter • Power Enacts the selected On-Screen Display Toggles the projector between standby (OSD) menu item. mode and Power ON. HDMI port indicator •...
Page 11
Remote control To use the remote mouse control keys • (Keystone keys) (Page Up, Page Down, , and ), see Manually corrects distorted images "Using the remote mouse control" on resulting from an angled projection. page 8 for details. • Enter •...
Page 12
• Mouse • (My Button) Switches between the normal and mouse Allows user to define a short cut key on modes. the remote control, and the function item is selected in OSD menu. PgUp, PgDn, : active after pressing Mouse. An icon appears on the screen to •...
Page 13
Operating the LASER pointer The Laser Pointer is a presentation aid for professionals. It emits colored light when you press it. The laser beam is visible. It is necessary to press and hold Laser for continuous output. Do not look into the laser light window or shine the laser light beam on yourself or others. See the warning messages on the back of the remote control prior to using it.
Page 14
• To return to the normal mode, press Mouse again or other keys except for the mouse related multi-function keys. Remote control effective range Refer to the illustration about the location of the Infra- Red (IR) remote control sensor(s). The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. Please see "Projector specifications" on page 79 for the native display resolution of this projector. For models with a 4:3 native aspect ratio •...
Page 17
4:3 image on a 16:10 Screen (a) Screen Size (b) Projection distance (d) Vertical offset (c) Image height min. max. min. max. Inch Inch Inch Inch Inch Inch 1524 1631 2120 1778 1903 2473 2032 2174 2827 1077 2286 2446 3180 1212 2540...
Page 18
When the projector’s native resolution is WXGA (1280 x 800) with a throw ratio of 1.21~1.57 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance (d) Vertical offset (c) Image height min. max. min. max. Inch Inch Inch Inch Inch...
Page 19
For models with a 16:9 native aspect ratio • 16:9 image on a 16:9 screen • 16:9 image on a 4:3 screen (e): Screen (f): Center of lens When the projector’s native resolution is 1080p (1920 x 1080) with a throw ratio of 1.15~1.5 16:9 image on a 16:9 Screen (a) Screen Size...
16:9 image on a 4:3 Screen (a) Screen Size (b) Projection distance (d) Vertical offset (c) Image height min. max. min. max. Inch Inch Inch Inch Inch Inch 1524 1409 1831 1778 1643 2137 2032 1878 2442 2286 2113 2747 1029 2540 2348...
Connection When connecting a signal source to the projector, be sure to: Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents"...
Page 22
Audio cable Audio Computer (for Component signal) Audio cable A/V device VGA cable Computer Monitor VGA to DVI-A cable S-Video cable S-Video A/V device connector Video cable Video A/V device connector (for S-Video/Video signal) Audio cable Audio in A/V device USB 5V/ USB Power Charger 2A Out...
(Trigger only) 12V Out Powered screen Microphone Audio Out Speakers Connecting a computer or monitor Connecting a computer Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector.
The COMPUTER OUT output only works when COMPUTER IN 1 connection is made to the projector in the standby mode. To use this connection method, turn on the Active VGA Out function under the SOURCE > Standby Settings menu. Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: •...
Page 25
Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. Take an HDMI cable and connect one end to the HDMI output port of the video device. Connect the other end of the cable to the HDMI input port on the projector. In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. Take a Video cable and connect one end to the composite Video output socket of the Video source device.
The greater volume you require, the greater distance you need to be away from the speaker to prevent the noise. Using the cable management cover (optional) This cable management cover helps you to conceal and organize the cables connected to the back of the projector.
Operation Starting up the projector Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). (If available) Remove the lens cap. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone"...
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Status...
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus"...
Page 31
Entering the password recall procedure Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals.
The current source information will be displayed in the upper left corner of the screen for 3 seconds. The screen will display ViewSonic logo while auto adjustment is functioning. This function is only available when PC D-Sub input signal (analog RGB) is selected.
Correcting keystone Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. •...
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal.
16:9 Not available 16:10 Not available available Panorama available 2.35:1 Anamorphic available Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps.
Page 37
DICOM SIM mode is only for training or reference. It not used for actual diagnosis. DICOM represents for the Digital Imaging and Communications in Medicine. This is a standard created by the American College of Radiology and the National Electrical Manufacturers Association.
Page 38
Adjusting Sharpness Go to the IMAGE > Advanced > Sharpness menu and press The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes. This function is only available when the input signal is S-Video, Video, YPbPr (digital) or YCbCr (digital).
Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc., you can project any image from the disc on the screen and enter the Color Management menu to make adjustments.
Press Enter or wait for 3 seconds to activate the timer. To display the Presentation Timer page, select Advanced. • Using the OSD menu Go to the BASIC > Presentation Timer menu. Press Enter to display the Presentation Timer page. Highlight Timer Period and decide the time period by pressing .
BASIC > Blank Timer You can set the blank time in the menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen. Once Blank is pressed, the projector enters Eco mode automatically. CAUTION Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.
Using the CEC function This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically.
Controlling the projector through a LAN environment ® The projector supports Crestron software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. (An example of connection) Configuring the LAN Control Settings If you are in a DHCP environment:...
Page 44
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again. If you wish to connect to the projector in its standby mode, be sure you have selected Static IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server information when the projector is on.
Page 45
If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events. The Crestron (e-Control) page displays the Crestron e-Control user interface. See "About Crestron e-Control®" on page 41 for details.
Page 46
/ > < $ % + \ ' " are prohibited. ® About Crestron e-Control ® The Crestron e-Control page provides a variety of virtual keys to control the projector or adjust the projected pictures. You can press reveal more buttons.
Page 47
ii. You can name the projector, keep track of its location and the person in charge of iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v.
Page 48
The info page displays the information and status of this projector. Press Exit to go back to the remote network operation page. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™...
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure the cable connections are correctly made. For the connection methods, see the Connection chapter.
Page 50
Adjusting the Audio In 2 setting Open the OSD menu and go to the BASIC > Audio Settings > Audio In 2 menu. Press to decide the audio input source for the AUDIO IN 2/MIC port. This will affect the connection method for different devices, and where the sound is from. •...
Shutting down the projector Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. Press Power a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.
Page 53
Top-Left/Bottom-Left/Top- Timer Position Presentation BASIC Right//Bottom-Right Timer Timer Counting Count Down/Count Up Direction Sound Reminder On/Off Start Counting/Off Off/Test Card/Note Pad/ Pattern World Map/Stave/Trellis Chart Disable/5 min/10 min/15 min/ Blank Timer 20 min/25 min/30 min Message On/Off Splash Screen Black/Blue/ViewSonic/Off...
Page 54
Main menu Sub-menu Options Auto/Projection (Projector Position)/Menu Position/Color Temp./Brightness/Contrast/3D Settings/Screen Color/Splash Screen/ My Button BASIC Message/Quick Auto Search/CEC/DCR/Closed Caption/Power Saving/Freeze/INFORMATION/ Aspect Ratio/USB Power 3D Glasses DLP/3D VESA Auto/Off/Frame Sequential/Frame 3D Settings 3D Sync Packing/Top-Bottom/ Side-by-Side 3D Sync Invert Disable/Invert HDMI Format Auto/RGB/YUV HDMI Settings HDMI Range...
Page 55
Main menu Sub-menu Options Multi-language OSD Language selection Front Table/Rear Table/ Projector Position Rear Ceiling/Front Ceiling 5 sec/10 sec/15 sec/20 Menu Display Time sec/25 sec/30 sec Menu Settings Center/Top-Left/Top- Menu Position Right/Bottom-Left/ Bottom-Right 6. SYSTEM High Altitude Mode On/Off Quick Auto Search On/Off Change Password Security Settings...
Page 56
Description of each menu Function Description Screen Color "Using Screen Color" on page 32 for details. Aspect Ratio "Selecting the aspect ratio" on page 30 for details. Keystone "Correcting keystone" on page 29 for details. Displays the position adjustment page. To move the projected image, use the directional arrow keys.
Page 57
Function Description Color Mode "Selecting a picture mode" on page 31 for details. Brightness "Adjusting Brightness" on page 32 for details. Contrast "Adjusting Contrast" on page 32 for details. "Selecting a Color Temperature" on page 33 "Setting a Color Temp. preferred color temperature"...
Page 58
Function Description Computer Selecting Enable allows the projector to turn on automatically once the VGA signal is fed through the VGA cable. Auto Power On "Using the CEC function" on page 37 for details. Direct Power On Selecting On allows the projector to turn on automatically once the power is fed through the power cord.
Page 59
Function Description 3D Settings "Using the 3D functions" on page 37 for details. HDMI Settings "Changing HDMI input settings" on page 27 for details. LAN Control "Controlling the projector through a LAN environment" on page 38 for details. Settings Lamp Mode "Setting Lamp Mode"...
Page 60
Function Description Sets the language for the On-Screen Display (OSD) menus. Language "Using the menus" on page 24 for details. Projector "Choosing a location" on page 10 for details. Position Menu Display Time Sets the length of time the OSD will remain active after your last key press.
Page 61
Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the IMAGE menu. Resolution Shows the native resolution of the input signal. Color System Shows input system format. IP Address Shows the IP address of your projector. Current System Status MAC Address...
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface.
Page 63
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter Be sure to turn off the projector and unplug it from power source. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots.
The timer will continue counting the next time you fit the filter back on and set Filter Mode to Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer.
Page 65
Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy menu. Press Enter and the Smart Energy page is displayed. Highlight Power Saving and press When Enable is selected, the projector lamp will be changed to Eco mode after no signal is detected for 5 minutes.
Page 66
Indicators Light Status & Description Power events Blue Stand-by mode Flashing Powering up Blue Normal operation Blue Blue Normal power-down cooling (3 sec) Flashing Downloading Burn in off Blue Blue Blue Lamp events Blue First Lamp-Lit error cooling (60 sec) Flashing Lamp error in normal operation (30 sec) CW start fail (30 sec)
Troubleshooting The projector does not turn on. Cause Remedy Plug the power cord into the AC inlet on the projector, and plug the power cord into the power There is no power from the power cord. outlet. If the power outlet has a switch, make sure that it is switched on.
Specifications Dimensions 469.5 mm (W) x 139.8 mm (H) x 316.24 mm (D) (Including extrusions) FOCUS ZOOM 469.5 316.24 139.8 Ceiling mount installation Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 3.50 286.20 Unit: mm 291.20...
IR control table Format Byte1 Byte2 Byte3 Byte4 PgDn PgUp Blank Auto sync Down Left Right Color Mode Mute Enter Power ON Presentation Timer Exit Eco Mode Menu Mouse Mouse Left Mouse Right Source Pattern My button HDMI Volume+ Volume- Magnify Aspect Video...
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) 640 x 480 60/72/75/85 SVGA 800 x 600 60/72/75/85 1024 x 768 60/70/75/85 1152 x 864 1280 x 768 15:9 WXGA 1280 x 800 16:10 60/75/85 1360 x 768 16:9 Quad-VGA 1280 x 960...
Page 81
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) 640 x 480 SVGA 800 x 600 1024 x 768 1280 x 768 15:9 WXGA 1280 x 800 16:10 1360 x 768 16:9 Quad-VGA 1280 x 960 SXGA 1280 x 1024 SXGA+ 1400 x 1050 WXGA+...
Page 82
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 60* / 120** 1024 x 768 60* / 120** 1280 x 720 16:9 50* / 60* / 120** WXGA 1280 x 800 16:9 60* / 120** WXGA 1366 x 768 16:9...
Page 83
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 SDTV (576p) 720 x 576...
Projector specifications All specifications are subject to change without notice. Not all models can be purchased in your region. Model name PG800X PG800W PG800HD Product Specification Resolution 0.55” XGA (1024 0.65” WXGA (1280 0.65” 1080p (1920 x x 768) x 800)
Page 85
Environmental Requirements Operating 0°C–40°C at sea level Temperature Operating Altitude 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C (with High Altitude Mode on) Operating Relative 10%–90% (without condensation) Humidity...
Latin America C= http://www.viewsonic.com/ www.viewsonic.com/la/ soporte@viewsonic.com (Mexico) la/soporte/servicio-tecnico Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F. Tel: 55) 6547-6454 55)6547-6484 Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico Latin America C= http://www.viewsonic.com/ www.viewsonic.com/la/ soporte@viewsonic.com (Peru) la/soporte/servicio-tecnico Macau www.hk.viewsonic.com T= 853-2840-3687 service@hk.viewsonic.com...
Page 87
(1) year for the original lamp from the date of the first consumer purchase. Other regions or countries: Please check with your local dealer or local ViewSonic office for the warranty information. Limited One (1) year Heavy Usage Warranty: Under heavy usage settings, where a projector’s use includes more than fourteen...
Page 88
Exclusion of damages: ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for: 1. Damage to other property caused by any defects in the product, damages based...
Page 89
If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components &...
Page 90
Tel: (52) 999-925-1916 Tel: 01(52)95-15-15-22-22 E-Mail: rrrb@sureste.com Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com Tijuana: FOR USA SUPPORT: ViewSonic Corporation Av Ferrocarril Sonora #3780 L-C 14035 Pipeline Ave. Chino, CA 91710, USA Col 20 de Noviembre Tel: 800-688-6688 (English); 866-323-8056 (Spanish); Tijuana, Mexico E-Mail: http://www.viewsonic.com...