Page 1 Foreword Congratulations on choosing a SUBARU vehicle. This Owner’s Manual has all the information necessary to keep your SUBARU in excellent condition and to properly maintain the emission control system for minimizing emission pollutants. We urge you to read this manual carefully so that you may understand your vehicle and its operation.
Page 2 This manual describes the following vehicle types. 1) 4-door 2) 5-door and OUTBACK 3) WRX STI...
Page 4: Seat, Seatbelt And Srs Airbags
Warranties & Warranties for U.S.A. All SUBARU vehicles distributed by Subaru of America, Inc. and sold at retail by an authorized SUBARU dealer in the United States come with the following warranties: SUBARU Limited Warranty Emission Control Systems Warranty Emissions Performance Warranty...
Page 5: Safety Warnings
This chapter informs you how to keep your SUBARU looking good. Chapter 11: Maintenance and service This chapter informs you when you need to take your SUBARU to the dealer for scheduled maintenance and informs you how to keep your SUBARU running properly.
Page 6: Vehicle Symbols
Vehicle symbols There are some of the symbols you may see on your vehicle. For warning and indicator lights, refer to “Warning and indicator lights” F22. Mark Name WARNING CAUTION Power door lock and unlock Passengers’ windows lock and unlock Fuel Front fog lights Hazard warning flasher...
Page 7 Mark Name Air recirculation Engine oil Washer Door lock (transmitter) Door unlock (transmitter) Trunk lid (4-door) or rear gate (5-door) (transmitter) Safety precautions when driving & Seatbelt and SRS airbag WARNING All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move.
Page 8: Child Safety
& Child safety WARNING Never hold a child on your lap or in your arms while the vehicle is moving. The passenger cannot protect the child from injury in a collision, because the child will be caught between the passen- ger and objects inside the vehi- cle.
Page 9: Drinking And Driving
“*SRS airbag (Supplemental Restraint System airbag)” F1-37. & Engine exhaust gas (carbon monoxide) WARNING Never inhale engine exhaust gas. Engine exhaust gas contains carbon monoxide, a colorless and odorless gas which is dan- gerous, or even lethal, if inhaled. Always properly maintain the en- gine exhaust system to prevent engine exhaust gas from enter- ing the vehicle.
Page 10 When possible, you should share the driving with others. & Modification of your vehicle CAUTION Your vehicle should not be modified other than with genuine SUBARU parts and accessories. Other types of modifications could affect its performance, safety or durability, and may even violate governmental regulations.
Page 11: Tire Pressures
wish to operate the controls of the navigation system, first take the vehicle off the road and stop it in a safe place. & Driving with pets Unrestrained pets can interfere with your driving and distract your attention from driving. In a collision or sudden stop, unrestrained pets or cages can be thrown around inside the vehicle and hurt you or your passengers.
Page 12: Table Of Contents
Table of contents Seat, seatbelt and SRS airbags Keys and doors Instruments and controls Climate control Audio Interior equipment Starting and operating Driving tips In case of emergency Appearance care Maintenance and service Specifications Consumer information and Reporting safety defects Index...
Page 13 Illustrated index & Exterior Engine hood (page 11-5) Headlight switch (page 3-35) Replacing bulbs (page 11-48) Wiper switch (page 3-40) Moonroof (page 2-26) Door locks (page 2-4) Tire pressure (page 11-35) Flat tires (page 9-6) Snow tires (page 8-10) 10) Front fog light switch (page 3-38) 11) Tie-down hooks (page 9-14) 12) Towing hook (page 9-14)
Page 14 Rear window defogger button (page 3-45) Fuel filler lid and cap (page 7-5) Child safety locks (page 2-19) Tie-down hook (page 9-14) Trunk lid (page 2-22) Rear gate (page 2-24) Towing hook (page 9-14) – CONTINUED –...
Page 15 & Interior ! Passenger compartment area Lower anchorages for child restraint system (page 1-31) Seatbelt (page 1-11) Parking brake lever (page 7-43) Front seat (page 1-2) Rear seat (page 1-7)
Page 16 Center console (page 6-5) Cup holder (page 6-5) Front power supply socket (page 6-8) Glove box (page 6-5) – CONTINUED –...
Page 17 & Instrument panel Door locks (page 2-4) Outside mirror switch (page 3-44) Illumination brightness control (page 3-37) Headlight beam leveler (page 3-38) Light control switch (page 3-35) Combination meter (page 3-5/page 3-12) Wiper control lever (page 3-39) Hazard warning flasher switch (page 3-5) Audio (page 5-1) 10) Shift lever (MT) (page 7-15/page 7-17)/ Select lever (AT) (page 7-23)
Page 18 & Light control and wiper control levers/switches Windshield wiper (page 3-40) Mist (page 3-41) Windshield washer (page 3-41) Rear window wiper and washer switch (page 3-41) Wiper intermittent time control switch (page 3-40) Wiper control lever (page 3-39) Light control switch (page 3-35) Fog light switch (page 3-38) Headlight ON/OFF (page 3-35) 10) Headlight flasher High/Low beam...
Page 19 & Combination meter ! U.S.-spec. models (WRX STI) Fuel gauge (page 3-9) Tachometer (page 3-9) Speedometer (page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Odometer/Trip meter (page 3-7) Temperature gauge (page 3-10)
Page 20 ! U.S.-spec. models (turbo models except WRX STI) Fuel gauge (page 3-9) Tachometer (page 3-9) Speedometer (page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Odometer/Trip meter (page 3-7) Select lever/gear position indicator (AT models) (page 3-29) Temperature gauge (page 3-10) –...
Page 21 ! U.S.-spec. models (non-turbo models) Tachometer (page 3-14) Speedometer (page 3-13) Fuel gauge (page 3-15) Trip meter A/B selection and trip meter reset knob (page 3-13) Odometer/Trip meter (page 3-13) Select lever/gear position indicator (AT models) (page 3-29) Coolant temperature warning/indicator light (page 3-20)
Page 22 ! Except U.S.-spec. models (WRX STI) Fuel gauge (page 3-9) Tachometer (page 3-9) Speedometer (page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Odometer/Trip meter (page 3-7) Temperature gauge (page 3-10) – CONTINUED –...
Page 23 ! Except U.S.-spec. models (turbo models except WRX STI) Fuel gauge (page 3-9) Tachometer (page 3-9) Speedometer (page 3-7) Trip meter A/B selection and trip meter reset knob (page 3-7) Odometer/Trip meter (page 3-7) Select lever/gear position indicator (AT models) (page 3-29) Temperature gauge (page 3-10)
Page 24 ! Except U.S.-spec. models (non-turbo models) Tachometer (page 3-14) Speedometer (page 3-13) Fuel gauge (page 3-15) Trip meter A/B selection and trip meter reset knob (page 3-13) Odometer/Trip meter (page 3-13) Select lever/gear position indicator (AT models) (page 3-29) Coolant temperature warning/indicator light (page 3-20) –...
Page 25 & Warning and indicator lights Mark Name Page Seatbelt warning light 3-16 Front passenger’s 3-16 seatbelt warning light SRS airbag system 3-18 warning light Front passenger’s frontal airbag ON indi- 3-19 cator Front passenger’s frontal airbag OFF in- 3-19 dicator CHECK ENGINE warning light/Malfunc- 3-19...
Page 26 Mark Name Page Driver’s control center differential auto indi- 3-30 cator light (WRX STI) Driver’s control center differential indicator 3-31 and warning lights (WRX STI) REV indicator light 3-31 (WRX STI) Auto [+] mode indica- 3-30 tor light (WRX STI) Auto [−] mode indica- 3-31 tor light (WRX STI)
Page 27 Function settings A SUBARU dealer can change the settings of the functions shown in the following table to meet your personal requirements. Contact the nearest SUBARU dealer for details. If your vehicle is equipped with the genuine SUBARU navigation system, the settings for some of these functions can be changed using the navigation monitor.
Page 28 Item Function Seatbelt warning Sounds a chime while driving Possible settings Default setting Operation/Non-operation Operation Page 1-12...
Page 29 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 30 Models with SRS airbags and lap/shoulder 1-11 restraints for driver, front passenger, and 1-11 window-side rear passengers... 1-12 SUBARU advanced frontal airbag system ... SRS side airbag and SRS curtain airbag... 1-12 SRS airbag system monitors... 1-12 SRS airbag system servicing ...
Page 31: Front Seats
Seat, seatbelt and SRS airbags Front seats WARNING Never adjust the seat while driv- ing to avoid the possibility of loss of vehicle control and of personal injury. Before adjusting the seat, make sure the hands and feet of rear seat passengers and cargo are clear of the adjusting mechan- ism.
Page 32: Forward And Backward Adjustment
tions concerning child restraint sys- tems, refer to “Child restraint sys- tems” F1-24. & Forward and backward ad- justment Pull the lever upward and slide the seat to the desired position. Then release the lever and move the seat back and forth to make sure that it is securely locked into place.
Page 33: Seat Cushion Height Adjustment (Driver's Seat)
Seat, seatbelt and SRS airbags & Seat cushion height adjust- ment (driver’s seat) When the lever is pushed down, the seat is lowered. When the lever is pulled up, the seat rises. The height of the seat can be adjusted by moving the seat cushion adjustment lever up and down.
Page 34: Active Head Restraint (If Equipped)
If your vehicle is involved in a The seat heater is equipped in the front rear-end collision, have an seats. authorized SUBARU dealer in- spect the active head restraints. The seat heater operates when the igni- tion switch is either in the “Acc” or “ON”...
Page 35: Type A Seat Heater
Seat, seatbelt and SRS airbags & Type A seat heater HI – Rapid heating LO – Normal heating OFF – Off Left-hand side Right-hand side To turn on the seat heater, push the “LO” or “HI” position on the switch, as desired, depending on the temperature.
Page 36: Rear Seats
Rear seats WARNING Seatbelts provide maximum re- straint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or...
Page 37: Head Restraint Adjustment
Seat, seatbelt and SRS airbags & Head restraint adjustment Both the rear window side seats and the rear center seat are equipped with head restraints. WARNING Never drive the vehicle with the head restraints removed because they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear.
Page 38: Folding Down The Rear Seatback
When not used (lowest position) When used (click position) Head restraint Release button To raise: Pull the head restraint up. To lower: Push the head restraint down while pressing the release button on the top of the seatback. To remove: While pressing the release button, pull out the head restraint.
Page 39 1-10 Seat, seatbelt and SRS airbags To return the seatback to its original position, raise the seatback until it locks into place and make sure that it is securely locked. You can keep the seatbacks locked when you leave your vehicle and valet key at a parking facility.
Page 40: Seatbelts
Seatbelts & Seatbelt safety tips WARNING All persons in the vehicle should fasten their seatbelts BEFORE the vehicle starts to move. Other- wise, the possibility of serious injury becomes greater in the event of a sudden stop or acci- dent. All belts should fit snugly in order to provide full restraint.
Page 41: Emergency Locking Retractor (Elr)
1-12 Seat, seatbelt and SRS airbags tions only) and then if necessary move the child closer to the belt buckle to help provide a good shoulder belt fit. Care must be taken to securely place the lap belt as low as possible on the hips and not on the child’s waist.
Page 42 For further details about canceling the warning operation, please contact your SUBARU dealer. If there is no passenger on the front passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated.
Page 43: Fastening The Seatbelt
If the seatbelt warning device for front passenger’s seat still does not function correctly after taking relevant corrective actions described above, immediately contact your SUBARU dealer for an inspection. & Fastening the seatbelt WARNING Never use a belt that is twisted or reversed.
Page 44 WARNING Never place the shoulder belt under the arm or behind the back. If an accident occurs, this can increase the risk or severity of injury. CAUTION Metallic parts of the seatbelt can become very hot in a vehicle that has been closed up in sunny weath- er;...
Page 45 1-16 Seat, seatbelt and SRS airbags Pull down on the anchor to make sure that it is locked in place. WARNING When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position.
Page 46 ! Unfastening the seatbelt Push the button on the buckle. Before closing the door, make sure that the belts are retracted properly to avoid catching the belt webbing in the door. ! Rear center seatbelt on 5-door models Center seatbelt tongue plate Connector (tongue) Connector (buckle) Center seatbelt buckle...
Page 47 1-18 Seat, seatbelt and SRS airbags WARNING Be sure to fasten both tongue plates to the respective buckles. If the seatbelt is used only as a shoulder belt (with the connector’s tongue plate not fastened to the connec- tor’s buckle on the right-hand side), it cannot properly restrain the wear- er in position in an accident, possi- bly resulting in serious injury or...
Page 48 4. Insert the center seatbelt tongue plate into the center seatbelt buckle marked “CENTER” on the left-hand side until it clicks. 5. To make the lap part tight, pull up on the shoulder belt. 6. Place the lap belt as low as possible on your hips, not on your waist.
Page 49: Seatbelt Maintenance
1-20 Seat, seatbelt and SRS airbags 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the retractor while it is rolling up. Insert the connector (tongue) into the belt holder. &...
Page 50: Front Seatbelt Pretensioners
SUBARU dealer. When replacing seat- belt retractor assemblies, use only genuine SUBARU parts. If either front seatbelt does not...
Page 51: System Monitors
1-22 Seat, seatbelt and SRS airbags ping the entire vehicle due to collision damage or for other reasons, consult your SUBARU dealer. & System monitors SRS airbag system warning light (turbo models) SRS airbag system warning light (non- turbo models)
Page 52: System Servicing
SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS...
Page 53: Precautions Against Vehicle Modification
1-24 Seat, seatbelt and SRS airbags & Precautions against vehicle modification Always consult your SUBARU dealer if you want to install any accessory parts to your vehicle. CAUTION Do not perform any of the following modifications. Such modifications can interfere with proper operation of the seatbelt pretensioners.
Page 54: Where To Place A Child Restraint System
Since the SRS airbag deploys with considerable speed and force, the child could be injured or even killed. & Where to place a child re- The following are SUBARU’s recommen- dations on where to place a child restraint system in your vehicle. WARNING Children should be properly re- strained at all times.
Page 55: Choosing A Child Restraint System
1-26 Seat, seatbelt and SRS airbags In this seating position, you should use only a child restraint system that has a bottom base that fits snugly against the contours of the seat cushion and can be securely retained using the seatbelt. If it is unavoidable to install a child restraint system in the rear seat’s center seating position, lower the center head...
Page 56: Installing Child Restraint Systems With A/Elr Seatbelt
looking for the label on the child restraint system or the manufacturer’s statement of compliance in the document attached to the system. Also it is important for you to make sure that the child restraint system is compa- tible with the vehicle in which it will be used.
Page 57 1-28 Seat, seatbelt and SRS airbags 6. Push and pull the child restraint system forward and from side to side to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt.
Page 58 4. Take up the slack in the lap belt. 5. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then, allow the belt to rewind into the retractor.
Page 59: Installing A Booster Seat
1-30 Seat, seatbelt and SRS airbags “Top tether anchorages” F1-34. 9. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. NOTE When the child restraint system is no longer in use, remove it and restore the...
Page 60: Installation Of Child Restraint Systems By Use Of Lower And Tether Anchorages (Latch)
4. To remove the booster seat, press the release button on the seatbelt buckle and allow the belt to retract. WARNING Never use a belt that is twisted or reversed. In an accident, this can increase the risk or severity of injury to the child.
Page 61 1-32 Seat, seatbelt and SRS airbags Some types of child restraint systems can be installed on the rear seat of your vehicle without use of the seatbelts. Such child restraint systems are secured to the designated anchorages provided on the vehicle body.
Page 62 You will find marks “ ” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower an- chorages (bars). Each lower anchorage is located where the seat cushion meets the seatback. 1. Use the “ ” marks to locate the two lower anchorages (bars) for the position where you want to install the child restraint system.
Page 63: Top Tether Anchorages
If you have any question concerning this type of child restraint system, ask your SUBARU dealer. & Top tether anchorages Your vehicle is equipped with two or three top tether anchorages so that a child restraint system having a top tether can be installed in the rear seat.
Page 64 For right seat Two or three upper anchorages are installed on the rear shelf behind the rear seat. ! 5-door models For left seat For center seat (for the Latin American models, a tether anchorage is not pro- vided in this center location.) For right seat 1-35 Seat, seatbelt and SRS airbags...
Page 65 5-door models 3. Attach the child restraint top tether hook to the appropriate upper anchorage. 4. Tighten the top tether securely. Please contact your SUBARU dealer if you have any question regarding the installation of a child restraint system. CAUTION...
Page 66: Srs Airbag (Supplemental Restraint System Airbag)
*SRS airbag (Supplemental Restraint System airbag) *SRS: This stands for supplemental re- straint system. This name is used be- cause the airbag system supplements the vehicle’s seatbelts. Your vehicle is equipped with a crash sensing and diagnostic module, which will record the use of the seatbelt by the front passenger when any of the SRS frontal, side and curtain airbags deploys.
Page 67 1-38 Seat, seatbelt and SRS airbags ment, the driver should always sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat.
Page 68 get fresh air promptly. A deploying SRS airbag releases hot gas. Occupants could get burned if they come into direct contact with the hot gas. NOTE When you sell your vehicle, we urge you to explain to the buyer that it is equipped with SRS airbags by alerting him or her to the applicable section in this Owner’s Manual.
Page 69 1-40 Seat, seatbelt and SRS airbags ! Components Airbag control module (including impact sensors) Frontal airbag module (driver’s side) Frontal airbag module (front passenger’s side) Front sub sensor (left-hand side) Front sub sensor (right-hand side) Side airbag module (driver’s side) Side airbag module (front passenger’s side) Side airbag sensor (center pillar left-hand...
Page 70: Subaru Advanced Frontal Airbag System
& SUBARU advanced frontal airbag system Your vehicle is equipped with a SUBARU advanced frontal airbag system that com- plies with the new advanced frontal airbag requirements in the amended Federal Motor Vehicle Safety Standard (FMVSS) No. 208. The SUBARU advanced frontal airbag system automatically determines the de- ployment force of the driver’s SRS frontal...
Page 71 1-42 Seat, seatbelt and SRS airbags WARNING Never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. WARNING The SRS airbag deploys with con- siderable speed and force.
Page 72 SRS frontal airbag even when the driver’s SRS frontal airbag deploys. This is normal. Observe the following precautions. Failure to do so may prevent the SUBARU advanced frontal airbag system from functioning correctly or cause the system to fail.
Page 73 1-44 Seat, seatbelt and SRS airbags warning light will illuminate. Have the system inspected by your SUBARU deal- er immediately if the SRS airbag system warning light illuminates. If your vehicle has sustained impact, this may affect the proper function of the SUBARU advanced frontal airbag system.
Page 74 facing child restraint system and a small child is restrained with it. (See WARNING that follows.) The seat is equipped with a booster seat and a small child is in the booster seat. (See WARNING that follows.) The seat is relieved of the occupant load for a time exceeding the predeter- mined monitoring time period.
Page 75 OFF indicator turns off after taking relevant corrective actions de- scribed above, relocate the child restraint system to the rear seat and immediately contact your SUBARU dealer for an inspection. NOTE When a child who has outgrown a child restraint system or a small adult is seated in the front passenger’s seat,...
Page 76 Subaru of America, Inc. Customer Dealer Services Department P.O. Box 6000 Cherry Hill, NJ 08034-6000 1-800-SUBARU3 (1-800-782-2783) <Hawaii> Servco Subaru Inc., dba Subaru Hawaii 2850 Pukoloa Street, Suite 202, Honolulu, HI 96819 808-839-2273 <Guam> Shen’s Corporation dba Prestige Automo- bile...
Page 77 After deployment, SRS AIRBAGs start to deflate immediately so that the driver’s vision is not obstructed. The SRS airbag can function only when the ignition switch is in the “ON” position. The SUBARU advanced frontal airbag system is designed to determine the activation or deactivation condition of the front passenger’s SRS frontal airbag depending on the total load on the front passenger’s seat monitored by the front...
Page 78 The two inflators of each airbag are triggered either sequentially or simulta- neously, depending on the severity of impact, in the case of the driver’s SRS frontal airbag and depending on the severity of impact and the total load on the seat in the case of the front passen- ger’s SRS frontal airbag.
Page 79 1-50 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which it is possible that the driver’s/driver’s and front passen- ger’s SRS frontal airbag(s) will de- ploy. Only the driver’s SRS frontal airbag or both driver’s and front passenger’s SRS frontal airbags may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface...
Page 80 ! Examples of the types of accidents in which deployment of the driver’s/driver’s and front passenger’s SRS frontal airbag(s) is unlikely to occur. 1-51 Seat, seatbelt and SRS airbags The vehicle strikes an object, such as a telephone pole or sign pole. The vehicle slides under the load bed of a truck.
Page 81 1-52 Seat, seatbelt and SRS airbags There are many types of collisions which might not necessarily require deployment of driver’s/driver’s and front passenger’s SRS frontal airbag(s). In the event of accidents like those illustrated, the dri- ver’s/driver’s and front passenger’s SRS frontal airbag(s) may not deploy depend- ing on the level of accident forces in- volved.
Page 82: Srs Side Airbag And Srs Curtain Airbag
& SRS side airbag and SRS curtain airbag The SRS side airbag is stored in the door side of each front seat seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact collision, the SRS side airbag on the impacted side of the vehicle deploys between the occupant and the door panel and supplements the seatbelt by reducing...
Page 83 1-54 Seat, seatbelt and SRS airbags WARNING Do not rest your arm on either front door or its internal trim. It could be injured in the event of SRS side airbag deployment. WARNING Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/ her arms around the front seat...
Page 84 WARNING Do not attach accessories to the door trim or near either SRS side airbags and do not place objects near the SRS side airbags. In the event of the SRS side airbag deployment, they could be pro- pelled dangerously toward the vehicle’s occupants and cause injuries.
Page 85 1-56 Seat, seatbelt and SRS airbags deploy independently of each other since each has its own impact sensor. There- fore, they may not both deploy in the same accident. Also, the SRS side airbag and SRS curtain airbag deploys independently of the driver’s and front passenger’s SRS frontal airbags in the steering wheel and instrument panel.
Page 86 ! Example of the type of accident in which the SRS side airbag and SRS curtain airbag will most likely de- ploy. A severe side impact near the front seat activates the SRS side airbag and SRS curtain airbag. 1-57 Seat, seatbelt and SRS airbags –...
Page 87 1-58 Seat, seatbelt and SRS airbags ! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag are unlikely to deploy. The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment.
Page 88: Seat, Seatbelt And Srs Airbags
! Examples of the types of accidents in which the SRS side airbag and SRS curtain airbag will basically not deploy. The vehicle is involved in frontal collision with another vehicle (moving or station- ary). The vehicle is struck from behind. The SRS side airbag and SRS curtain airbag are basically not designed to deploy if the vehicle is involved in a frontal...
Page 89 SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS...
Page 90: Srs Airbag System Servicing
CAUTION If you need service or repair in areas indicated in the following list, have the work performed by an author- ized SUBARU dealer. The SRS air- bag control module, impact sensors and airbag modules are stored in these areas.
Page 91 Own- er’s Manual. Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body. Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.
Page 92: Keys And Doors
Keys ... Key number plate ... Immobilizer ... Security ID plate... Security indicator light ... Key replacement ... Door locks ... Locking and unlocking from the outside ... Locking and unlocking from the inside ... Battery drainage prevention function ... Power door locking switches ...
Page 93: Keys
Keys and doors Keys Master key (Black) Submaster key (Black) Valet key (Gray) Key number plate Security ID plate Three types of keys are provided for your vehicle: Master key, submaster key and valet key. The master key and submaster key fit all locks on your vehicle.
Page 94: Security Id Plate
device may not cause harmful inter- ference, and (2) this device must accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
Page 95: Key Replacement
If the security indicator light does not flash, the immobilizer system may be malfunc- tioning. If this occurs, contact your SUBARU dealer as soon as possible. In case an unauthorized key is used (e.g. an imitation key), the security indicator light illuminates.
Page 96: Locking And Unlocking From The Inside
Rotate the lock lever rearward. Close the door. To lock the door from the outside without the key, rotate the lock lever rearward and then close the door. To lock the door from the outside using the power door locking switch, push the front side of the switch (“LOCK”...
Page 97: Power Door Locking Switches
(5- door) are completely closed. The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact your SUBARU dealer to change the setting. NOTE The factory setting (default setting) for this function is set as “operational”.
Page 98: Key Lock-In Prevention Function
This function’s operational/non-opera- tional setting can be changed by a SUBARU dealer. Contact a SUBARU dealer for details. NOTE When leaving the vehicle, make sure you are holding the key before locking the doors.
Page 99: Locking The Doors
Keys and doors to the following two conditions: (1) This device may not cause harmful inter- ference, and (2) this device must accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.
Page 100: Unlocking The Doors
& Unlocking the doors Press the “ ” button to unlock the driver’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors and the rear gate (5- door), briefly press the “ ”...
Page 101: Selecting Audible Signal Operation
10 seconds after Step 3. 5. The turn signal lights flash 3 times to indicate completion of the setting. You may have the above settings done by your SUBARU dealer. & Replacing the battery CAUTION Do not let dust, oil or water get on or in the transmitter when repla- cing the battery.
Page 102: Replacing Lost Transmitters
Negative (−) side facing up 3. Replace with a new battery (type CR2025 or equivalent) making sure to install the new battery with the negative (−) side facing up. 4. Refit the removed half of the transmit- ter case. After the battery is replaced, the trans- mitter must be synchronized with the remote keyless entry system’s control unit.
Page 103 2-12 Keys and doors (1) Open and close the driver’s door once. LOCK (2) Insert the key into the ignition switch, then turn it from the “LOCK” position to the “ON” position 10 times within 15 seconds. NOTE When you complete step (2), an electronic tone will sound once.
Page 104 the switch and the next exceeds 5 seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 6. When you have finished entering the number, push the unlock side of the lock switch within 5 seconds.
Page 105: Alarm System
Map lights (models with moonroof) The notifications regarding the dome light and the map lights are deactivated as the factory setting. A SUBARU dealer can activate the system. Contact your SUBARU dealer for details. & Activating and deactivating the alarm system To change the setting of your vehicle’s...
Page 106: If You Have Accidentally Triggered The Alarm System
NOTE You may have the above setting change done by your SUBARU dealer. & If you have accidentally trig- gered the alarm system ! To stop the alarm Do any of the following operations: Press any button on the remote trans- mitter.
Page 107 The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. If your vehicle is a 4-door and you unlock the trunk using the remote transmitter’s “...
Page 108: Disarming The System
DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system CAUTION In passive mode, the system will...
Page 109: Tripped Sensor Identification
2-18 Keys and doors LOCK 2. Turn the ignition switch from “ON” to “LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of the vehicle. 4. Before closing the doors, lock all doors with the inside door lock levers.
Page 110: Shock Sensors (Dealer Option)
30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE The shock sensors are not always...
Page 111: Windows
2-20 Keys and doors Windows & Power windows WARNING To avoid serious personal injury caused by entrapment, always con- form to the following instructions without exception. When operating the power win- dows, be extremely careful to prevent anyone’s fingers, arms, neck, head or other objects from being caught in the window.
Page 112 held. ! Operating the passengers’ windows To open: Push the appropriate switch down and hold it until the window reaches the desired position. To close: Pull the switch up and hold it until the window reaches the desired position. ! Locking the passengers’ windows Lock Unlock Push the lock switch.
Page 113: Trunk Lid (4-Door)
2-22 Keys and doors Trunk lid (4-door) WARNING To prevent dangerous exhaust gas from entering the vehicle, always keep the trunk lid closed while driving. Help prevent young children from locking themselves in the trunk. On hot or sunny days, the tem- perature in the trunk could quickly become high enough to cause death or serious heat-...
Page 114 inside the trunk. In the event children or adults become locked inside the trunk, the handle allows them to open the lid. The handle is located on the inside of the trunk lid. To open the trunk lid from inside the trunk, pull the yellow handle upward as indicated by the arrow on the handle.
Page 115: Rear Gate (5-Door)
Also, if the movement of the release handle feels restricted or not entirely smooth during operation, or the handle and/or handle base is cracked, contact your SUBARU dealer. Rear gate (5-door) The rear gate can be locked and unlocked using any of the following systems.
Page 116 To close: Lower the rear gate slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip. WARNING To prevent dangerous exhaust gas from entering the vehicle, always keep the rear gate closed while driving.
Page 117: Moonroof (If Equipped)
2-26 Keys and doors Moonroof (if equipped) WARNING Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, always con- form to the following instructions...
Page 118: Sun Shade
NOTE One-touch operation does not take place when the moonroof is lowered. Push the switch continuously to raise and lower the moonroof. ! Sliding moonroof Open Close Push the “OPEN/CLOSE” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof.
Page 119 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 120: Instruments And Controls
Ignition switch ... LOCK... Acc... ON... START ... Key reminder chime ... Ignition switch light ... Hazard warning flasher... Meters and gauges (turbo models)... Combination meter illumination ... Canceling the function for meter/gauge needle movement upon turning on the ignition switch...
Page 121 Instruments and controls SPORT mode indicator light (AT models) ... SI-DRIVE indicator light (WRX STI)... Shift-up indicator light (WRX STI)... Select lever/gear position indicator (AT models) ... Turn signal indicator lights ... High beam indicator light ... Cruise control indicator light ... Cruise control set indicator light...
Page 122: Ignition Switch
Ignition switch WARNING Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, preventing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer.
Page 123: Acc
Instruments and controls The key can be turned from “Acc” to “LOCK” only when the select lever is in the “P” position. ! MT models The key can be turned from “Acc” to “LOCK” only when the key is pushed in while turning it.
Page 124: Key Reminder Chime
contains an immobilizer transponder. The key is near or touching another transmitter. & Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “Acc” position. The chime stops when the ignition switch is turned to the “ON”...
Page 125: Canceling The Function For Meter/Gauge Needle Movement Upon Turning On The Ignition Switch
Instruments and controls & Canceling the function for meter/gauge needle move- ment upon turning on the ignition switch It is possible to activate or deactivate the movement of the meter needles and gauge needles that takes place when the ignition switch is turned to the “ON” position.
Page 126: Speedometer
nation after the driver’s door is opened, the illumination will be turned off. Even during the gradual turning off after the ignition switch is turned to the “LOCK” position, if the ignition switch is turned to the “ON” position, the combination meter illuminate as usual.
Page 127 Instruments and controls : WRX STI only : “ ” or “ ”, and “ ” or “ ” cannot be displayed when the ignition switch is in the “ON” position. : Except WRX STI For the “ ” or “ ”...
Page 128: Tachometer
& Tachometer The tachometer shows the engine speed in thousands of revolutions per minute. CAUTION Do not operate the engine with the pointer of the tachometer in the red zone. This may cause severe da- mage to the engine. & Fuel gauge Low fuel warning light The fuel gauge shows the approximate amount of fuel remaining in the tank.
Page 129: Temperature Gauge
3-10 Instruments and controls & Temperature gauge Normal operating range The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position. The coolant temperature will vary in accordance with the outside temperature and driving conditions. We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range.
Page 130: Setting The Alarm-Level Engine Speed
NOTE Even if the REV alarm system is not set, the REV indicator light will illuminate whenever the engine speed enters the tachometer’s red zone. & Setting the alarm-level en- gine speed 1. Push the trip knob to select “REV” on the combination meter.
Page 131: Deactivating The Rev Alarm System
3-12 Instruments and controls to OFF, OFF to ON, or the vehicle starts moving before the setting procedure is finished. Setting the speed is impossible when the vehicle is moving. The set engine speed may differ from the engine speed shown by the tachometer.
Page 132: Speedometer
*: “ ” or “ ” cannot be displayed when the ignition switch is in the “ON” posi- tion. To change the current setting, press the trip knob for at least 2 seconds. : Activated : Deactivated NOTE Your vehicle’s initial movement setting of the meter/gauge needles has been set for activation “...
Page 133: Tachometer
3-14 Instruments and controls ! Odometer The odometer shows the total distance that the vehicle has been driven. ! Double trip meter The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2...
Page 134: Fuel Gauge
& Fuel gauge Low fuel warning light The fuel gauge shows the approximate amount of fuel remaining in the tank. When the ignition switch is in the “LOCK” or “Acc” position, the fuel gauge shows “E” even if the fuel tank contains fuel. The gauge may move slightly during braking, turning or acceleration due to fuel level movement in the tank.
Page 135: Warning And Indicator Lights
If any lights fail to illuminate, it indicates a burned-out bulb or a malfunction of the : Low fuel warning light corresponding system. Consult your authorized SUBARU dealer : Hill start assist warning light (MT models – if equipped)/Hill start assist for repair.
Page 136 For further details about canceling the warning operation, please contact your SUBARU dealer. If there is no passenger on the front passenger’s seat, the seatbelt warning device for the front passenger’s seat will be deactivated.
Page 137: Srs Airbag System Warning Light
If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. & SRS airbag system warning light When the ignition switch is turned to the “ON”...
Page 138: Front Passenger's Frontal Airbag On And Off Indicators
2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the SUBARU ad- vanced frontal airbag system monitoring. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain off.
Page 139: Turbo Models)/Coolant Temperature High
“Engine overheating” F9- – Blinking in RED and BLUE alternately: The electrical system may be malfunctioning. Contact your SUBARU dealer for an inspec- tion. This coolant temperature low indicator light/coolant temperature high warning light has the following three functions.
Page 140: Charge Warning Light
SUBARU dealer. Also, if the indicator light/warning light often blinks in RED, the electrical system may be malfunctioning. Contact your SUBARU dealer for an inspection. NOTE If the engine is restarted after a certain driving condition, this indicator light/ warning light may illuminate in RED.
Page 141: Rear Differential Oil Temperature Warning Light (Wrx Sti)
3-22 Instruments and controls the automatic transmission control system is not working properly. Contact your nearest SUBARU dealer for service im- mediately. & Rear differential oil temperature warning light (WRX STI) CAUTION Reduce vehicle speed and park the vehicle in a safe place as soon as possible if the R.DIFF TEMP light...
Page 142 Should the warning light illuminate stea- dily after blinking for approximately one minute, have the system inspected by your nearest SUBARU dealer as soon as possible. WARNING If this light does not illuminate briefly after the ignition switch is...
Page 143: Abs Warning Light
If at all in doubt about whether the brakes are operating prop- erly, do not drive the vehicle. Have your vehicle towed to the nearest SUBARU dealer for re- pair. This light has the following three functions. ! Parking brake warning...
Page 144: Low Fuel Warning Light
If the fluid level is below the “MIN” mark in the reservoir, do not drive the vehicle. Have the vehicle towed to the nearest SUBARU dealer for repair. ! Electronic Brake Force Distribution (EBD) system warning...
Page 145: Door Open Warning Light
The Vehicle Dynamics Control system is probably malfunctioning under any of the following conditions. Have your vehicle checked at a SUBARU dealer immedi- ately. The light does not illuminate when the ignition switch is turned to the “ON”...
Page 146: Vehicle Dynamics Control Warning Light
You will be safe while driving with this condition, but have your vehicle checked at a SUBARU dealer as soon as possible. NOTE If the warning light behavior is as...
Page 147: Security Indicator Light
The Vehicle Dynamics Control system is probably malfunctioning under the follow- ing condition. Have your vehicle checked at a SUBARU dealer as soon as possible. The light does not turn off even after the lapse of several minutes (the engine has warmed up) after the engine has started.
Page 148: Sport Mode Indicator Light (At Models)
NOTE Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally. & SPORT mode indicator light (AT models) This light illuminates when the ignition switch is turned to the “ON”...
Page 149: Turn Signal Indicator Lights
3-30 Instruments and controls & Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as possible. Refer to “Replacing bulbs”...
Page 150: Driver's Control Center Differential Indicator And Warning Lights (Wrx Sti)
! Warning light All the indicator lights will flash in the event that the driver’s control center differential has a malfunction. Have the vehicle inspected by your SUBARU dealer. For details, refer to “Driver’s Control Center Differential (DCCD) (WRX STI)” F7-19. 3-31 Instruments and controls &...
Page 151: Clock
3-32 Instruments and controls Clock The time changes by 1 minute each time the “+” button or “−” button is pressed. Pressing the “+” button moves the dis- played time forward, while pressing the “−” button moves the displayed time back. Pressing and holding either button changes the displayed time continuously.
Page 152: Outside Temperature Indicator
The fuel consumption display is linked with the odometer/trip meter display ac- cording to the following chart. Odometer/Trip Fuel consumption indicator meter A trip meter Average fuel consumption corresponding to the A trip meter B trip meter Average fuel consumption corresponding to the B trip meter Odometer...
Page 153: Current Fuel Consumption (If Equipped)
3-34 Instruments and controls “ON” position, the indication does not flash. NOTE The outside temperature indication may differ from the actual outside temperature. The road surface freeze warning indication should be treated only as a guide. Be sure to check the condition of the road surface before driving.
Page 154: Light Control Switch
tion indicator will automatically turn on when the battery voltage is discon- nected and then reconnected for bat- tery replacement or fuse replacement. Light control switch The light control switch operates when the key is inserted into the ignition switch. Regardless of the position of the light control switch, the illuminated lights are turned off when the key is removed from...
Page 155: High/Low Beam Change (Dimmer)
3-36 Instruments and controls & High/low beam change (dim- mer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the combina- tion meter also illuminates.
Page 156: Turn Signal Lever
Turn signal lever To activate the right turn signal, push the turn signal lever up. To activate the left turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand.
Page 157: Headlight Beam Leveler (If Equipped)
3-38 Instruments and controls Headlight beam leveler (if equipped) The vehicle has High-Intensity Discharge (HID) headlights on the low beam setting. The HID headlights generate more light than conventional halogen headlights. Therefore a driver of an oncoming vehicle may experience too much glare when your headlight beam height adjustment is high due to the vehicle carrying a heavy load.
Page 158: Wiper And Washer
In dow glass periodically with a washer areas where water freezes in solution to prevent streaking, and to winter, use SUBARU Windshield remove accumulations of road salt or Washer Fluid or the equivalent. 3-39 Instruments and controls Refer to “Windshield washer...
Page 159: Windshield Wiper And Washer Switches
3-40 Instruments and controls road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. Grease, wax, insects or other mate- rial on the windshield or the wiper blade results in jerky wiper operation and streaking on the glass.
Page 160: Rear Window Wiper And Washer Switch - 5-Door
! Mist (for a single wipe) For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. ! Washer To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button.
Page 161: Mirrors
3-42 Instruments and controls speed is high). When you subsequently move the select lever to the “R” position (AT models) or the shift lever to the reverse position (MT models), the rear wiper will switch to continuous operation. When you move the select lever/shift lever from the “R”/ reverse position to some other position, the rear wiper will return to intermittent...
Page 162 or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror surface turns bright if the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing.
Page 163: Outside Mirrors
3-44 Instruments and controls exit the zone setting mode. & Outside mirrors ! Convex mirror (passenger side) WARNING Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes.
Page 164: Climate Control
mirror switch continuously, it may not work. This is not a malfunction. Oper- ate the switch again after waiting for a short period of time. When you unfold the outside mirrors manually, the mirrors may become wobbly. Be sure to unfold the mirrors by switch operation.
Page 165 For models with the automatic climate control system, it is possible to set the defogger and deicer system for the con- tinuous operation mode as follows. Models with genuine SUBARU navi- gation system: The setting can be changed for the continuous operation mode using the navigation monitor.
Page 166: Tilt Steering Wheel (If Equipped)
Tilt steering wheel (if equipped) WARNING Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury. If the lever cannot be raised to the fixed position, adjust the steering wheel again.
Page 167: Horn
3-48 Instruments and controls 1. Adjust the seat position. Refer to “Front seats” F1-2. 2. Pull the tilt/telescopic lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place. 5.
Page 168 Ventilator... Air flow selection ... Center and side ventilators ... Manual climate control system (if equipped) ... Control panel ... Heater operation ... Air conditioner operation... Automatic climate control system (if equipped) ... Control panel ... To use as full-automatic climate control system...
Page 169: Ventilator
Climate control Ventilator & Air flow selection...
Page 170: Center And Side Ventilators
& Center and side ventilators ! Center ventilators Move the tab up and down or right and left to adjust the flow direction. ! Side ventilators Open Close Thumb-wheel Move the tab up and down or right and left to adjust the flow direction. To open or close the ventilator, turn the thumb-wheel up or down.
Page 171 Climate control ! Fan speed control dial The fan operates only when the ignition switch is turned to the “ON” position. The fan speed control dial is used to select four fan speeds. ! Air flow control dial This dial has the following five positions: : Air flows through the instrument panel outlets.
Page 172: Heater Operation
WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears. & Heater operation ! Defrosting or defogging the wind- shield To direct warm air to the windshield and front door windows:...
Page 173 Climate control NOTE Warm air also comes out from the right and left air outlets. To stop warm air flow from these outlets, turn the corre- sponding thumb-wheel down. ! Heating To direct warm air toward the floor: 1. Set the air inlet selection button to the OFF position.
Page 174: Air Conditioner Operation
When driving on a dusty road, set the air inlet selection button to the “ON” position. WARNING Continued operation with the air inlet selection button in the ON position may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears.
Page 175: Automatic Climate Control System (If Equipped)
Climate control Automatic climate control system (if equipped) Although this climate control system can be used as a full-automatic climate control system, it can also, if desired, be used as a semi-automatic climate control system. When it is used as a full-automatic climate control system, the outlet air temperature, fan speed, air flow distribution, air inlet control, and air conditioner compressor...
Page 176: Fan Speed Control Dial
SUBARU recom- mends using the AUTO position. Other positions: The fan speed can be adjusted in 7 steps.
Page 177: Air Inlet Selection Button
To return to “AUTO” mode, turn the fan speed control dial or air flow control dial to a position other than the AUTO position. Then turn to “AUTO” mode. SUBARU recommends using the AUTO position. WARNING Continued operation in the ON posi- tion may fog up the windows.
Page 178: Climate Control
To return to “AUTO” mode, turn the fan speed control dial or air flow control dial to a position other than the AUTO position. Then turn to “AUTO” mode. SUBARU recommends using the AUTO position. NOTE The air conditioner’s compressor does not operate with an outside tempera- ture of 32 F (0 C) or lower.
Page 179: Operating Tips For Heater And Air Conditioner
HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
Page 180: Air Filtration System
Under extremely dusty conditions, the filter should be replaced more frequently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, use only a genuine SUBARU air filter kit. Replacement schedule:...
Page 181 4-14 Climate control 3. Replace the air filter element with a new one. CAUTION The arrow mark on the filter must point UP. 4. Reinstall the glove box, and connect the damper shaft. 5. Close the glove box. 6. LABEL installation (1) Attach the service label to the driver’s side door pillar.
Page 182: Audio
Antenna system ... Roof antenna ... FM reception ... satellite radio reception (if equipped)... Installation of accessories... Audio set ... Type A audio set (if equipped) ... Type B audio set (if equipped) ... Power and sound controls ... Power switch and volume control ... Sound control ...
Page 183: Antenna System
Audio Antenna system & Roof antenna CAUTION Be sure to lower the antenna rod before entering garages, parking towers and other locations with low ceilings. Remove the antenna rod before washing your car at a car wash. If the antenna rod is left attached, it may scratch the roof.
Page 184 You may experience problems in receiving satellite radio signals in the follow- ing situations. If you are driving northward in a coastal area You will notice that the XM satellite radio antenna is fixed to the upper right hand corner of your windshield. The signal comes from the south and may not be able to reach the antenna in some circumstances when you are driving north.
Page 185: Installation Of Accessories
Audio set Your SUBARU may be equipped with one of the following audio sets. Refer to the pages indicated in this section for operat- ing details.
Page 186: Type A Audio Set (If Equipped)
& Type A audio set (if equipped) Audio The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. Power and sound controls: refer to page 5-7 Radio operation: refer to page 5-10 Satellite radio operation (if equipped): refer to page 5-13 CD (compact disc) player operation: refer to page 5-16...
Page 187: Type B Audio Set (If Equipped)
Audio & Type B audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. Power and sound controls: refer to page 5-7 Radio operation: refer to page 5-10 Satellite radio operation (if equipped): refer to page 5-13 CD (compact disc) player operation: refer to page 5-16...
Page 188: Power And Sound Controls
Power and sound controls & Power switch and volume control The dial is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial, and the volume is controlled by turning the dial. &...
Page 189 Audio track/channel control mode after approxi- mately 5 seconds. ! SPEED VOLUME setting SPEED VOLUME CONTROL is a function that automatically adjusts the volume according to the vehicle speed. As the vehicle speed increases, the audio vo- lume automatically increases to match the vehicle speed, in order to create a pleasant listening environment even as the driving noise increases.
Page 190: Adjustable Level Of Each Mode
& Adjustable level of each mode Mode Volume Volume control AUX volume control* Tone and balance Bass control Midrange control Treble control Balance Fader Other settings SPEED VOLUME BEEP CS Auto (Type B audio) *: Only when an AUX audio product is connected. Range of levels Initial setting Turn counterclockwise...
Page 191: Fm/Am Radio Operation
5-10 Audio FM/AM radio operation & FM/AM selection Push the “FM AM” button when the radio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2, FM3 or AM reception.
Page 192 ! Scan tuning (SCAN) If you press the “SCAN” button, the radio will switch to the scan mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while display- ing the frequency, after which scanning will continue until the entire band has been scanned.
Page 193: Displaying Radio Ps (Program Service Name) And Rt (Radio Text)
5-12 Audio ! Seek in PTY (Program type) group In the PTY selection mode, when the desired PTY group has been selected, pressing the “SEEK” button “ ” or “ ” seeks within that PTY group. Pressing “ ” seeks up. Pressing “ ”...
Page 194: Satellite Radio Operation (If Equipped)
FM3 stations each may be preset. Satellite radio operation (if equipped) To receive satellite radio, it is necessary to install the SUBARU genuine satellite receiver (optional equipment) and to enter into a contract. For details, please contact your SUBARU dealer.
Page 195: Band Selection
5-14 Audio you activate satellite radio and receive satellite radio customer support. The satellite radio ID can be found on the audio display by tuning the channel to “0”. Turn the “CH” dial to select the satellite radio channel. NOTE For Sirius, change the display to an indication mode other than the channel number after performing the above...
Page 196: Channel Preset
! Category selection When in the SAT mode, press the “CAT” button “ ” or “ ” to change to the category search mode. When in the category search mode, pressing the “CAT” button “ ” changes the category up by one step. Pressing “ ”...
Page 197: Display Selection
5-16 Audio ! Selecting preset channels Presetting a channel with a preset button allows you to select that channel in a single operation. Up to six SAT1, SAT2 and SAT3 channels each may be preset. & Display selection Press the “TEXT” button while receiving the satellite radio to change the display as follows.
Page 198: How To Insert A Cd (Type A)
& How to insert a CD (type A) Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position.
Page 199: How To Play Back A Cd
5-18 Audio 2. Press the disc select button at the position where you want to insert a disc. 3. When the “LOAD” indicator illumi- nates, insert the disc. Once you have inserted the disc, the “LOAD” indicator will turn off. The disc will then be automatically drawn in, and the player will begin to play the first track on the disc.
Page 200 player will start playback. ! When there are CDs loaded (type B) Press a desired one of the disc select buttons the disc number indicator of which steadily lights up. The player will then start playback of the selected CD, beginning with the first track.
Page 201: Fast-Forwarding And Fast-Reversing
5-20 Audio & Fast-forwarding and fast-re- versing ! Fast-forwarding Press the “ ” side of the “SEEK” button continuously to fast-forward the disc/ folder. Release the button to stop fast-forwarding. NOTE If you fast-forward to the end of the last track/file (track), fast-forwarding will stop and the player will start playback beginning with the first track/file...
Page 202: Random Playback
NOTE The “RPT” indication refers to the repeat playback of a single track. It repeats the track that is playing. The “F-RPT” indication refers to the repeat playback of a folder. It repeats the all of the tracks in the folder. It is possible to select the function when the MP3/WMA format track is playing.
Page 203: Scan
5-22 Audio & Scan The scan mode lets you listen to the first 10 seconds of each track/file in succes- sion. Press the “SCAN” button to start scanning upward beginning with the track/ file(s) following the currently selected one. After all track/file(s) in the disk/folder have been scanned, normal playback will be resumed.
Page 204: Folder Selection
& Folder selection Press the “ ” side of the “FOLDER” button briefly to select the next folder. Press the “ ” side of the button briefly to go back to the previous folder. The folder title will be shown each time you press one of the buttons.
Page 205: When The Following Messages Are Displayed
CD player, determine the cause based on the follow- ing information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “PUSH EJECT” is displayed Press the eject button to unload the disc.
Page 206: Aux Unit Operation (If Equipped)
CDs are not supported) and data format are correct. This player can only play MP3 and WMA data formats. If the disc cannot be unloaded or this message remains displayed, please contact your SUBARU dealer. AUX unit operation (if equipped) &...
Page 207: Audio Control Buttons (If Equipped)
Refer to the Owner’s Manual of the portable audio player. NOTE The AUX jacks of the models with the genuine SUBARU navigation sys- tem are the RCA type. For detailed information, refer to the Owner’s Man- ual supplement for the navigation sys- tem.
Page 208 *1: The frequency last received in the selected waveband will be displayed. *2: Only when a CD is in the player. *3: Only when with an auxiliary audio product is connected. ! “ ” and “ ” buttons ! With radio mode selected Press the “...
Page 209: Precautions To Observe When Handling A Compact Disc
5-28 Audio Precautions to observe when handling a compact disc Use only compact discs (CDs, CD-Rs and CD-RWs) that have the mark shown in the following. Also, some compact discs cannot be played. You cannot use a DualDisc in the CD player.
Page 210 there are deposits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzine, alcohol, etc. Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-standard shape (for example, a heart shape).
Page 211 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 212: Interior Equipment
Interior lights ... Dome light ... Cargo area light (5-door models) ... Map lights ... Sun visors ... Vanity mirror ... Storage compartment ... Glove box ... Center console... Coin tray (if equipped) ... Cup holders ... Front passenger’s cup holder ... Rear passenger’s cup holder (if equipped) ...
Page 213: Interior Lights
The setting can be changed using the navigation monitor. For details, please refer to the Owner’s Manual supplement for the navigation system. Also, the setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. Models without genuine SUBARU navigation system: The setting can be changed by a SUBARU dealer.
Page 214: Map Lights
The setting can be changed using the navigation monitor. For details, please refer to the Owner’s Manual supplement for the navigation system. Also, the setting can be changed by a SUBARU dealer. Contact your SUBARU dealer for details. Models without genuine SUBARU navigation system: The setting can be changed by a SUBARU dealer.
Page 215: Sun Visors
Interior equipment Sun visors To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways. & Vanity mirror CAUTION Keep the vanity mirror cover closed while the car is being driven to avoid being temporarily blinded by the glare of bright light.
Page 216: Glove Box
& Glove box Lock Unlock To open the glove box, pull the handle. To close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clockwise. To unlock the glove box, insert the key and turn it counterclockwise. &...
Page 217 Interior equipment ! Except WRX STI A dual cup holder is built in the center console, beside the parking brake lever. ! WRX STI The dual cup holder is built into the center console near the parking brake lever. To access the cup holder, pull the lid toward the rear.
Page 218: Rear Passenger's Cup Holder (If Equipped)
& Rear passenger’s cup holder (if equipped) CAUTION When not in use, always keep the cup holder stored while driving to reduce the risk of injury in the event of a sudden stop or an accident. A dual cup holder is located at the back of the center console.
Page 219: Accessory Power Outlets
Interior equipment Accessory power outlets Power outlet below the climate controls Power outlet in the center console (except WRX STI) Power outlet in the center console (WRX STI) Accessory power outlets are provided below the climate controls and in the center console.
Page 220: Use With A Cigarette Lighter (If Equipped)
The electrical power socket lo- cated in the center console is originally designed to use a gen- Interior equipment uine SUBARU cigarette lighter plug. Do not use a non-genuine cigarette lighter plug in the sock- et. Doing so may cause a short- circuit and overheating, resulting in a fire.
Page 221: Ashtray (If Equipped)
Clean them off using a toothbrush or a similar narrow-ended implement. & Center console A portable ashtray is available from your SUBARU dealer. When using the ashtray, open the ashtray lid. Fully close the lid after using it to help reduce residual smoke.
Page 222: Floor Mat (If Equipped)
! WRX STI (if equipped) The rear ashtray is located on the upper side of the back of the center console. To open the ashtray, pull the upper edge of the lid. To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down.
Page 223: Cargo Area Cover (5-Door - If Equipped)
6-12 Interior equipment Cargo area cover (5-door – if equipped) The cargo area cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo. & Using the cover To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown.
Page 224: To Install The Cover Housing
& To install the cover housing 1. Shorten the bar. 2. Insert the projections located on the both ends of the sleeve into the recesses of the retainers. Cargo tie-down hooks (5-door – if equipped) The cargo area is equipped with four tie- down hooks so that cargo can be secured with a cargo net or ropes.
Page 225: Under-Floor Storage Compartment (If Equipped)
6-14 Interior equipment Under-floor storage compart- ment (if equipped) 4-door models 5-door models The storage compartment is located under the floor of the trunk (4-door) or the cargo area (5-door), and it can be used to store small items. To open the lid, pull the tab NOTE When storing a flat tire, put the storage tray in the trunk (4-door) or the cargo...
Page 226: Starting And Operating
Fuel ... Fuel requirements ... Fuel filler lid and cap... State emission testing (U.S. only)... Preparing to drive ... Starting the engine... MT models ... AT models... Stopping the engine... Remote engine start system (dealer option) ... Starting your vehicle ... Remote start safety features ...
Page 227 Starting and operating Steps to take if EBD system malfunctions... Vehicle Dynamics Control system (if equipped) ... 7-36 Vehicle Dynamics Control system monitor ... Vehicle Dynamics Control mode switch (WRX STI) ... Vehicle Dynamics Control OFF switch (except WRX STI) ... Tire pressure monitoring system (TPMS) (U.S.-spec.
Page 228: Fuel
Do not be concerned if your vehicle sometimes knocks lightly when you drive up a hill or when you accelerate. Contact your SUBARU dealer if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently.
Page 229 CHECK ENGINE warning light/Mal- function indicator lamp may turn on. If this happens, return to your authorized SUBARU Dealer for service. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty.
Page 230: Fuel Filler Lid And Cap
& Fuel filler lid and cap ! Refueling Only one person should be involved in refueling. Do not allow others to approach the area of the vehicle near the fuel filler pipe while refueling is in progress. Be sure to observe any other precautions that are posted at the service station.
Page 231 Starting and operating When opening the cap, grasp it firmly and turn it slowly to the left. Do not remove the cap quickly. Fuel may be under pres- sure and spray out of the fuel filler neck, especially in hot weather.
Page 232: State Emission Testing (U.s. Only)
At state inspection time, remember to tell your inspection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dynam- ometer. Otherwise, serious transmis- sion damage will result. Some states have started using dynam-...
Page 233 There are some states that use four-wheel dynamometers in their testing programs. When properly used, that equipment will not damage a SUBARU AWD vehicle. Under no circumstances should the rear wheels be jacked off the ground, nor should the driveshaft be disconnected for state emission testing.
Page 234: Preparing To Drive
“START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have turned off after the engine has started.
Page 235: At Models
“START” position without depressing the accelerator pedal. (4) If the engine still refuses to start, contact your nearest SUBARU dealer for assistance. 6. Confirm that all warning and indicator lights have turned off after the engine has started.
Page 236: Stopping The Engine
starting the engine. For non-turbo models, to protect the engine while the select lever is in the “P” or “N” position, the engine is controlled so that the engine speed may not become too high even if the accelerator pedal is depressed hard. Stopping the engine The ignition switch should be turned off only when the vehicle is stopped and the...
Page 237: Starting Your Vehicle
7-12 Starting and operating & Starting your vehicle The remote engine start system is acti- vated by pressing the “ ” button twice within 3 seconds on your remote engine start transmitter. The system will check certain pre-conditions before starting, and if all safety parameters are correct, the engine will start within 5 seconds.
Page 238: Pre-Heating Or Pre-Cooling The Interior Of The Vehicle
transmitter within a few seconds immedi- ately following remote engine start shut- down. & Pre-heating or pre-cooling the interior of the vehicle Before exiting the vehicle, set the tem- perature controls to the desired setting and operation. After the system starts the vehicle, the heater or air-conditioning will activate and heat or cool the interior to your setting.
Page 239: System Maintenance
7-14 Starting and operating the turn signal lights will flash 2 times to indicate Confirmation Horn Chirps are “ON”. Depressing the brake pedal repeat- edly will toggle the feature ON or OFF each time. 7. To exit the remote engine start trans- mitter and feature programming mode, turn the ignition switch to the “LOCK”...
Page 240: (Wrx Sti)
2. Remove the circuit board from the bottom half of the case and slide the white plastic battery holder out from under the battery tab releasing the batteries. Re- move the old batteries and replace with new ones. Be sure to observe the (+) sign on the old batteries before removing them to ensure that the new batteries are inserted properly (battery “+”...
Page 241: Selecting Reverse Gear
7-16 Starting and operating WARNING Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased.
Page 242: Driving Tips
In addition, sudden application of engine brakes when the vehicle is travelling on a slippery surface can lead to wheel locking; as a conse- quence, control of the vehicle may be lost and the risk of an accident increased. NOTE Never exceed posted speed limits.
Page 243: Shifting Speeds
7-18 Starting and operating WARNING Do not drive the vehicle with the clutch disengaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is consequently increased.
Page 244: Driving Tips
All the indicator lights will flash in the event that the driver’s control center differential has a malfunc- tion. Have the vehicle inspected by your SUBARU dealer. The driver’s control center differential allows you to freely change the degree of limitation of the differential action (limited slip differential (LSD) torque) of your vehicle’s center differential.
Page 245: To Change Mode Of Driver's Control Center Differential
7-20 Starting and operating tial and rear differential. This sound occurs because of the structure of the center differential. It does not indicate a problem. & To change mode of driver’s control center differential Press the “AUTO-MANU” switch on the center console to switch from auto mode to manual mode or vice versa.
Page 246: Manual Mode
the “AUTO [+]” mode. After setting the mode, “ ” on the combination meter illuminates. Pull the control switch rearward to select the “AUTO [−]” mode. After setting the mode, “ ” on the combination meter illuminates. When the “AUTO [+]” mode is selected, pull the control switch rearward to change to the “AUTO”...
Page 247 7-22 Starting and operating Push the switch forward to increase the initial LSD torque; when the “LOCK” indicator light illuminates, the initial LSD torque setting is maximum. The center differential will then be almost completely locked. Pull the switch rearward to reduce the initial LSD torque.
Page 248: Temporary Release
cause a braking effect accompanied by vibration and noise. This does not indicate a problem. The phenomenon will disappear when setting the initial LSD torque to the minimum. In the auto mode, it controls the initial LSD torque automatically. While in the auto mode, this phenomenon some- times occurs depending on the driving condition, however, it does not indicate...
Page 249: Select Lever
7-24 Starting and operating allow the transmission to shift at the most appropriate times for the current condition of your vehicle. Optimized shifting will be restored as the vehicle continues to be driven for a while. & Select lever : Shifting is possible with the brake pedal depressed : Shifting is possible whether the brake pedal is depressed or not...
Page 250: Shift Lock Function
If you must perform the above procedure, the shift lock system (or the vehicle control system) may be malfunctioning. Contact a SUBARU dealer for an inspection as soon as possible. If the select lever does not move after – CONTINUED –...
Page 251: Selection Of Manual Mode
If the select lever does not move after performing the above procedure, the shift lock system may be malfunctioning. Con- tact a SUBARU dealer for an inspection as soon as possible. & Selection of manual mode With the vehicle either moving or station- ary, move the select lever from the “D”...
Page 252: Driving Tips
Upshift indicator Downshift indicator Gear position indicator When the manual mode is selected, the gear position indicator and upshift indica- tor and/or downshift indicator on the combination meter illuminate. The gear position indicator shows the currently selected gear in the 1st-to-4th-gear range. The upshift and downshift indicators show when a gear shift is possible.
Page 253: Sport Mode
7-28 Starting and operating Do not keep the vehicle in a stationary position on an uphill grade by using the “D” position. Use the brake instead. The engine may, on rare occasions, knock when the vehicle rapidly acceler- ates or rapidly pulls away from a standstill. This phenomenon does not indicate a problem.
Page 254: Si-Drive (Wrx Sti)
SI-DRIVE (WRX STI) SI-DRIVE (SUBARU Intelligent Drive) works to maximize engine performance, control and efficiency. This system consists of three modes: Intelligent (I), Sport (S), and Sport Sharp (S#). By adjusting the SI-DRIVE selector, the character of the power unit changes.
Page 255: Sport Sharp (S#) Mode
Sport Sharp (S#) mode. While the vehicle is in the Sport Sharp (S#) mode, it changes to the Sport (S) mode when the engine coolant temperature in- creases. If any of the SI-DRIVE indicators blink, the SI-DRIVE system may be malfunctioning. Contact your SUBARU dealer.
Page 256: Limited Slip Differential (Lsd) (Wrx Sti)
Limited slip differential (LSD) (WRX STI) The LSD provides optimum distribution of power according to the difference in revolutions between the right and left wheels that may be caused by certain driving conditions, thereby improving driv- ing stability on snow-covered, muddy or other slippery roads or when high speed driving.
Page 257: Brake System
The disc brake pad wear warning indica- tors on the disc brakes give a warning noise when the brake pads are worn. If a squeaking or scraping noise is heard from the disc brakes while braking, im- mediately have your vehicle checked by your SUBARU dealer.
Page 258: Abs (Anti-Lock Brake System)
ABS (Anti-lock Brake Sys- tem) The ABS system prevents the lock-up of wheels which may occur during sudden braking or braking on slippery road sur- faces. This helps prevent the loss of steering control and directional stability caused by wheel lock-up. When the ABS system is operating, you may hear a chattering noise or feel a slight vibration in the brake pedal.
Page 259: Electronic Brake Force Distribution (Ebd) System
The warning light illuminates dur- ing driving. If these occur, have the ABS system repaired at the first available oppor- tunity by your SUBARU dealer. NOTE If the warning light behavior is as described below, the ABS system may be considered normal.
Page 260: Steps To Take If Ebd System Malfunctions
3. Release the parking brake. If both warning lights turn off, the EBD system may be malfunctioning. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights illuminate again and remain illuminated after the engine...
Page 261: Vehicle Dynamics Control System (If Equipped)
SUBARU dealer. Traction Control Function The following precautions should The traction control function is designed to be observed in order to ensure...
Page 262: Vehicle Dynamics Control System Monitor
NOTE Slight twitching of the brake pedal may be felt when the Vehicle Dynamics Control system operates; a small de- gree of vehicle or steering wheel shak- ing may also be noticed in this situa- tion. These are normal characteristics of Vehicle Dynamics Control operation and are no cause for alarm.
Page 263 The following two situations could indicate a malfunction of the Vehicle Dynamics Control system, and if either should occur, have an authorized SUBARU dealer carry out an inspection of that system at the first available opportunity. The indicator light does not illuminate when the ignition switch is turned to the “ON”...
Page 264 SUBARU dealer carry out an inspection of those systems at the first available oppor- tunity. NOTE...
Page 265: Vehicle Dynamics Control Mode Switch (Wrx Sti)
7-40 Starting and operating minutes have passed to allow the engine to heat up sufficiently. ! Traction Control OFF indicator light (green – WRX STI) This light illuminates to indicate that the Traction Control System is in non-opera- tion mode. This does not constitute failure of the Vehicle Dynamics Control system.
Page 266: Vehicle Dynamics Control Off Switch (Except Wrx Sti)
gine. When the Vehicle Dynamics Control OFF mode is selected, the vehicle’s running performance is comparable with that of a vehicle that does not have a Vehicle Dynamics Control sys- tem. Do not deactivate the Vehicle Dynamics Control system except when absolutely necessary.
Page 267: Tire Pressure Monitoring System (Tpms) (U.s.-Spec. Models)
7-42 Starting and operating Tire pressure monitoring system (TPMS) (U.S.-spec. models) Turbo models Non-turbo models The tire pressure monitoring system pro- vides the driver with a warning message by sending a signal from a sensor that is installed in each wheel when tire pressure is severely low.
Page 268: Parking Your Vehicle
SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light...
Page 269: Parking Tips
7-44 Starting and operating CAUTION Never drive while the parking brake is set because this will cause un- necessary wear on the brake lin- ings. Before starting to drive, always make sure that the parking brake has been fully released. &...
Page 270: Hill Start Assist System (Mt Models - If Equipped)
Hill start assist system (MT models – if equipped) CAUTION The Hill start assist system is a device only for helping the driver to START the vehicle on an uphill grade. To prevent accidents when the vehicle is parked on a slope, be sure to firmly set the parking brake.
Page 271 7-46 Starting and operating 4. Confirm the following items. The ABS warning light does not illuminate. The Vehicle Dynamics Control OFF indicator light does not illuminate. The Brake system warning light illuminates. 5. Press the Vehicle Dynamics Control mode switch and hold it until the Vehicle Dynamics Control OFF indicator light turns off.
Page 272: Hill Start Assist Warning Light/Hill Start Assist Off Indicator Light
Hill start assist system control, the warn- ing light will illuminate. If the warning light illuminates, have the vehicle inspected by your SUBARU dealer. ! Hill start assist OFF indicator light (WRX STI) While the Hill start assist system is...
Page 273: To Set Cruise Control
7-48 Starting and operating control is not in use to avoid uninten- tionally setting of the cruise control. & To set cruise control 1. Push the “CRUISE” main switch but- ton. Turbo models Non-turbo models The cruise control indicator light on the combination meter will illuminate.
Page 274: To Temporarily Cancel The Cruise Control
Non-turbo models At this time, the cruise control set indicator light is illuminated on the combination meter. The vehicle will maintain the desired speed. Vehicle speed can be temporarily in- creased while driving with the cruise control activated. Simply depress the accelerator pedal to accelerate the vehi- cle.
Page 275: To Change The Cruising Speed
7-50 Starting and operating & To change the cruising speed ! To increase the speed (by button) Push the “RES/ACC” button and hold it until the vehicle reaches the desired speed. Then, release the button. The vehicle speed at that moment will be memorized and treated as the new set speed.
Page 276: Cruise Control Indicator Light
If this indicator light and the CHECK 7-51 Starting and operating ENGINE warning light/malfunction in- dicator lamp flash simultaneously dur- ing driving, have the vehicle checked by your nearest SUBARU dealer. & Cruise control set indicator light Turbo models – CONTINUED –...
Page 277 7-52 Starting and operating Non-turbo models The cruise control set indicator light illuminates when the ignition switch is turned to the “ON” position and turns off after approximately 3 seconds. The light illuminates when vehicle speed has been set.
Page 278: Driving Tips
New vehicle break-in driving – the first 1,000 miles (1,600 km) ... Fuel economy hints ... Engine exhaust gas (carbon monoxide)... Catalytic converter ... Periodic inspections ... Driving in foreign countries ... Driving tips for AWD models... Off road driving ... All AWD models except OUTBACK ...
Page 279: New Vehicle Break-In Driving - The First 1,000 Miles (1,600 Km)
Driving tips New vehicle break-in driving – the first 1,000 miles (1,600 The performance and long life of your vehicle are dependent on how you handle and care for your vehicle while it is new. Follow these instructions during the first 1,000 miles (1,600 km): Do not race the engine.
Page 280: Catalytic Converter
(misfiring, back- firing or incomplete combustion), have your vehicle checked and repaired by an authorized SUBARU dealer. Do not apply undercoating or rust prevention treatment to the heat shield of catalytic converter and the exhaust sys- tem.
Page 281: Periodic Inspections
Driving tips operates at very high tempera- tures. Keep everyone and flammable materials away from the exhaust pipe while the engine is running. The exhaust gas is very hot. Periodic inspections To keep your vehicle in the best condition at all times, always have the recom- mended maintenance services listed in the maintenance schedule in the “War- ranty and Maintenance Booklet”...
Page 282: Driving Tips For Awd Models
By shifting power between the front and rear wheels, SUBARU AWD can also provide added traction during acceleration and added engine braking force during deceleration.
Page 283: Off Road Driving
& OUTBACK Your SUBARU can be driven on ordinary roads or off-road. But please keep in mind that an AWD SUBARU is a passenger vehicle and is neither a conventional off- road vehicle nor an all-terrain vehicle.
Page 284 “Warranty and Mainte- nance Booklet”. Remember that damage done to your SUBARU while operating it off-road and not using common sense precautions such as those listed above is not eligible for warranty coverage.
Page 285: Winter Driving
Do not use engine antifreeze or other substitutes because they may damage the paint of the vehicle. SUBARU Windshield Washer Fluid con- tains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 286: Driving On Snowy And Icy Roads
Driving tips If your SUBARU is not going to be used for an extended period, it is best to have the fuel tank filled to capacity. & Driving on snowy and icy...
Page 287: Corrosion Protection
8-10 Driving tips roads. This may cause loss of vehicle control. CAUTION Avoid prolonged continuous driving in snowstorms. Snow will enter the engine’s intake system and may hinder the air flow, which could result in engine shutdown or even breakdown. ! Wiper operation when snowing Before driving in cold weather, make sure the wiper blades are not frozen to the...
Page 288: Tire Chains
struction, brand, and load range. Mixing other sizes or construc- tions may result in severe me- chanical damage to the drive train of your vehicle and may affect ride, handling, braking and speedometer/odometer calibra- tion. It also may be dangerous and lead to loss of vehicle con- trol.
Page 289: Loading Your Vehicle
8-12 Driving tips Loading your vehicle WARNING Never allow passengers to ride on a folded rear seatback, in the trunk or in the cargo area. Doing so may result in serious injury. Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or...
Page 290: Gvwr And Gawr (Gross Vehicle Weight Rating And Gross Axle Weight Rating)
The load capacity of your vehicle is determined by weight, not by available cargo space. The maximum load you can carry in your vehicle is shown on the vehicle placard attached to the driver’s side door pillar. It includes the total weight of the driver and all passengers and their belongings, any optional equipment such as a roof rack or bike carrier, etc.
Page 291: Roof Molding And Crossbar (If Equipped)
8-14 Driving tips & Roof molding and crossbar (if equipped) CAUTION For cargo carrying purposes, the roof molding must be used to- gether with a roof crossbar kit and the appropriate carrying at- tachment. Otherwise, damage to the roof or paint or a dangerous road hazard due to loss of cargo could result.
Page 292: Trailer Towing
Therefore, never tow a trailer with your vehicle. SUBARU assumes no responsibility for injuries or vehicle damage that may result from trailer towing, from any trailer towing equipment or from any errors or omissions in the instructions accompanying such equipment.
Page 293 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 294 If you park your vehicle in case of an emergency ... Temporary spare tire... Precautions for AWD models with automatic transmission ... Maintenance tools ... Tool bag... Under the rear floor... Flat tires... Changing a flat tire... Tire pressure monitoring system (TPMS) (U.S.-spec.
Page 295: Temporary Spare Tire
This indicates the tire pressure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or sys- tem resetting.
Page 296: Precautions For Awd Models With Automatic Transmission
possible because the spare tire is de- signed only for temporary use. Check the inflation pressure of the tem- porary spare tire periodically to keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2 kg/cm When using the temporary spare tire, note the following.
Page 297: Maintenance Tools
In case of emergency Spare fuse FWD connector 3. Put a spare fuse inside the FWD connector located in the cabin and confirm that the All-Wheel Drive warning light “ ” illuminates. The All-Wheel-Drive capability of the vehicle has now been deactivated.
Page 298: Under The Rear Floor
& Under the rear floor Jack handle 4-door models 5-door models Under-floor storage compartment (if equipped) (Refer to “Under-floor storage compartment” F6-14.) Tool bucket Spare tire 4-door models 5-door models In case of emergency Wheel nut wrench Hex-head wrench (only models with moonroof) Screwdriver Jack...
Page 299: Flat Tires
In case of emergency Models with 17-inch wheel tires The jack handle is stored under the floor of the trunk (4-door) or the cargo area (5- door). The jack and towing hook are stored in the tool bucket that is located in the recess of the spare tire wheel.
Page 300 5. Take out the jack, jack handle and wheel nut wrench. The tools and the spare tire are stored under the floor of the trunk (4-door) or the cargo area (5-door). Refer to “Mainte- nance tools” F9-4. NOTE Make sure that the jack is well lubri- cated before using it.
Page 301 In case of emergency Jack-up points (vehicle with side sill skirt except WRX STI) Jack-up points (others) 9. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire. Turn the jackscrew by hand until the jack head engages firmly into the jack-up point.
Page 302 WARNING Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident. 14. Turn the jack handle counterclockwise to lower the vehicle. 15.
Page 303: Tire Pressure Monitoring System (Tpms) (U.s.-Spec. Models)
This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or...
Page 304: Jump Starting
Jump starting WARNING Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes.
Page 305 9-12 In case of emergency (1) Connect one jumper cable to the positive (+) terminal on the discharged battery. (2) Connect the other end of the jumper cable to the positive (+) term- inal of the booster battery. (3) Connect one end of the other cable to the negative (−) terminal of the booster battery.
Page 306: Engine Overheating
9-13 In case of emergency Towing If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety. WARNING Never tow AWD models (both AT and...
Page 307: Towing And Tie-Down Hooks
9-14 In case of emergency & Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow). CAUTION Use only the specified towing hook and tie-down hook. Never use suspension parts or other parts of the body for towing or tie-down purposes.
Page 308 Models with fog lights Models without fog lights 2. Cover the tip of a flat-head screwdriver with vinyl tape or cloth so that it will not scratch the bumper. Insert the flat-head screwdriver into the cutout of the cover and pry open the cover. 3.
Page 309 9-16 In case of emergency Rear towing hook: 1. Take the towing hook out of the tool bucket and take the screwdriver out of the tool bag. Take the jack handle out of the trunk (4-door) or cargo area (5-door). 2.
Page 310: Using A Flat-Bed Truck
Rear tie-down hooks: The rear tie-down hooks are located near each of the jack-up reinforcements. WARNING Use the rear tie-down hooks only for downward anchoring. If they are used to anchor the vehicle in any other direction, cables may slip off the hooks, possibly causing a dan- gerous situation.
Page 311: Rear Gate - If The Rear Gate Cannot Be Unlocked
9-18 In case of emergency towed. 4. Take up slack in the towline slowly to prevent damage to the vehicle. WARNING Never turn the ignition switch to the “LOCK” position while the vehicle is being towed because the steering wheel and the direc- tion of the wheels will be locked.
Page 312: Moonroof - If Moonroof Cannot Be Closed
a similar tool. 3. To unlock the rear gate, turn the lever to the right position using a flat-head screwdriver or a similar tool. 4. Open the rear gate from outside by raising the rear gate handle. Moonroof – if moonroof can- not be closed If the moonroof cannot be closed with the moonroof switch, you can close the moon-...
Page 313: In Case Of Emergency
9-20 In case of emergency clockwise. To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked and repaired by an authorized SUBARU dealer.
Page 314 Exterior care ... 10-2 Washing... Waxing and polishing ... Cleaning aluminum wheels ... Corrosion protection... 10-4 Most common causes of corrosion ... To help prevent corrosion... Appearance care Cleaning the interior... 10-2 Seat fabric ... 10-3 Leather seat materials... 10-3 Synthetic leather upholstery...
Page 315: Exterior Care
10-2 Appearance care Exterior care & Washing CAUTION When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly depressing the brake pedal to heat up the brakes.
Page 316: Appearance Care
When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list. NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.
Page 317: Corrosion Protection
Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance. Repair chips and scratches in the paint as soon as you find them.
Page 318: Cleaning The Interior
If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and head restraints be covered, or the windows shaded, to prevent fading or shrinkage.
Page 319: Navigation Monitor (If Equipped)
10-6 Appearance care & Navigation monitor (if equipped) To clean the navigation monitor, wipe it with a silicone cloth or with a soft cloth. If the navigation monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent.
Page 320: Maintenance And Service
Maintenance schedule ... Maintenance precautions... Before checking or servicing in the engine compartment... When you do checking or servicing in the engine compartment while the engine is running... Engine hood ... Engine compartment overview... Non-turbo models ... Turbo models except WRX STI... WRX STI ...
Page 321 Maintenance and service Tires and wheels ... Types of tires ... Tire pressure monitoring system (TPMS) (if equipped)... Tire inspection ... Tire pressures and wear ... Wheel balance... Wear indicators ... Tire rotation direction mark ... Tire rotation ... Tire replacement ... Wheel replacement...
Page 322: Maintenance Schedule
Maintenance precautions When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer. If you perform maintenance and service by yourself, you should familiarize yourself with the information provided in this section on general maintenance and service for your SUBARU.
Page 323: Before Checking Or Servicing In The Engine Compartment
NEVER use a circuit tester for this wiring. If your SRS airbag or seatbelt pretensioner needs service, con- sult your nearest SUBARU deal- & Before checking or servicing in the engine compartment WARNING Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.
Page 324: Engine Hood
Engine hood To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original position. 2. Pull the hood release knob under the instrument panel. 3. Release the secondary hood release by moving the lever between the front grille and the hood toward the left.
Page 325: Fuse Box (Page
11-6 Maintenance and service Engine compartment overview & Non-turbo models Power steering fluid reservoir (page 11-26) Manual transmission oil level gauge (MT) (page 11-20) or Differential gear oil level gauge (AT) (page 11-23) Clutch fluid reservoir (page 11-28) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-27) Fuse box (page 11-46)
Page 326: Turbo Models Except Wrx Sti
& Turbo models except WRX STI 11-7 Maintenance and service Power steering fluid reservoir (page 11-26) Manual transmission oil level gauge (MT) (page 11-20) or Differential gear oil level gauge (AT) (page 11-23) Clutch fluid reservoir (page 11-28) Automatic transmission fluid level gauge (page 11-22) Brake fluid reservoir (page 11-27) Fuse box (page 11-46)
Page 327: Wrx Sti
11-8 Maintenance and service & WRX STI Power steering fluid reservoir (page 11-26) Clutch fluid reservoir (page 11-28) Brake fluid reservoir (page 11-27) Fuse box (page 11-46) Battery (page 11-45) Windshield washer tank (page 11-40) Engine oil filler cap (page 11-9) Engine coolant reservoir (page 11-14) Engine oil level gauge (page 11-9) 10) Radiator cap (page 11-14)
Page 328: Engine Oil
If the oil consumption rate seems abnormally high after the break-in period, for example more than 1 quart per 1,200 miles or 1 liter per 2,000 kilometers, contact your SUBARU deal- & Checking the oil level Check the engine oil level at each fuel stop.
Page 329: Changing The Oil And Oil Filter
11-10 Maintenance and service pipe, be sure to wipe it off. If you check the oil level just after stopping the engine, wait a few minutes for the oil to drain back into the oil pan before checking the level. Just after driving or while the engine is warm, the engine oil level reading may be in a range between the upper level and...
Page 330 Non-turbo models 7. Remove the oil filter with an oil filter wrench. 8. Before installing a new oil filter, apply a thin coat of engine oil to the seal. 9. Clean the rubber seal seating area of the bottom of engine and install the oil filter by hand turning.
Page 331: Recommended Grade And Viscosity
When adding oil, different brands may be used together as long as they are the same API classification and SAE viscosity as those recommended by SUBARU. SAE viscosity No. and applicable tempera- ture 5W-30 is preferred. Engine oil viscosity (thickness) affects fuel economy.
Page 332: Recommended Grade And Viscosity Under Severe Driving Conditions
, u s e o n l y SUBARU Super Coolant. If the SUBARU Super Coolant is diluted with another brand or type, the maintenance interval is...
Page 333: Engine Coolant
11-14 Maintenance and service If the fuse is not blown, have the cooling system checked by your SUBARU dealer. If frequent addition of coolant is neces- sary, there may be a leak in the engine cooling system. It is recommended that the cooling system and connections be checked for leaks, damage, or looseness.
Page 334 Always add genuine SUBARU coolant and genuine SUBARU cooling system conditioner whenever the coolant is re- placed. Change the engine coolant and add...
Page 335 Maintenance and service 5. Slowly pour the coolant and fill up to just below the filler neck, allowing enough room to add genuine SUBARU cooling system conditioner in the radiator. Add genuine SUBARU cooling system condi- tioner until the coolant level reaches the filler neck.
Page 336: Air Cleaner Element
CAUTION When replacing the air cleaner ele- ment, use a genuine SUBARU air cleaner element. If it is not used, there is the possibility of causing a negative effect to the engine.
Page 337 11-18 Maintenance and service 7. To install the air cleaner case, insert the three projections on the air cleaner case into the slits on the air cleaner case cover. 8. Install in the reverse order of removal. ! Turbo models 1.
Page 338: Spark Plugs
It may be difficult to replace the spark plugs. It is recommended that you have the spark plugs replaced by your SUBARU dealer. The spark plugs should be replaced according to the maintenance schedule in the “Warranty and Maintenance Book- let”.
Page 339: Specifications
(98 N, 10 kgf) midway between the pulleys by using a spring scale. The belt deflec- tion should be the amount specified. If the front side belt is loose, cracked or worn, contact your SUBARU dealer. in (mm) Deflection New belt Used belt 0.28 –...
Page 340: Recommended Grade And Viscosity
Check the oil level monthly. 1. Park the vehicle on a level surface and stop the engine. 2. Pull out the level gauge, wipe it clean, and insert it again. Upper level Lower level 3. Pull out the level gauge again and check the oil level on it.
Page 341: Automatic Transmission Fluid
11-22 Maintenance and service Automatic transmission fluid & Checking the fluid level The automatic transmission fluid expands largely as its temperature rises; the fluid level differs according to fluid temperature. Therefore, there are two different scales for checking the level of hot fluid and cold fluid on the level gauge.
Page 342: Recommended Fluid
NOTE For optimum transmission perfor- mance, only use the automatic trans- mission fluid that is recommended and provided by SUBARU. If the recommended automatic trans- mission fluid is unavailable, Dexron III may be temporarily used. If the Dexron III is used continuously there will be a noticeable increase in the vibration and noise from the automatic transmission.
Page 343: Recommended Grade And Viscosity
11-24 Maintenance and service & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives. Never use different brands together. Oil grade: API classification GL-5 SAE viscosity No. and applicable tempera- ture Rear differential gear oil &...
Page 344: Recommended Grade And Viscosity
If the vehicle requires frequent refilling, there may be an oil leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. 11-25 Maintenance and service & Recommended grade and viscosity Each oil manufacturer has its own base oils and additives.
Page 345: Power Steering Fluid
“MIN” and “MAX” line. If the fluid level is extremely low, it may indicate possible leakage. Consult your SUBARU dealer for an inspection. WARNING Be careful not to burn yourself because the fluid may be hot.
Page 346: Recommended Fluid
If the vehicle requires frequent refilling, there may be a leak. If you suspect a problem, have the vehicle checked at your SUBARU dealer. CAUTION When adding brake fluid, be care- ful not to allow any dirt into the reservoir.
Page 347: Recommended Brake Fluid
11-28 Maintenance and service & Recommended brake fluid Use one of the following types of fluid. – Genuine SUBARU brake fluid – FMVSS No. 116, fresh DOT 3 or DOT 4 brake fluid CAUTION Never use different brands of brake fluid together.
Page 348: Recommended Clutch Fluid
& Recommended clutch fluid Use one of the following types of fluid. – Genuine SUBARU brake fluid – FMVSS No. 116, fresh DOT 3 or DOT 4 brake fluid CAUTION Never use different brands of clutch fluid together. Also, avoid mixing DOT 3 and DOT 4 brake fluids even if they are the same brand.
Page 349: Brake Pedal
2 lbf (10 N, 1 kgf). If the free play is not within proper specification, contact your SUBARU deal- & Checking the brake pedal reserve distance More than 2.56 in (65 mm)
Page 350: Checking The Clutch Pedal Free Play
If you hear this scraping noise each time you apply the brake pedal, have the brake pads serviced by your SUBARU dealer as soon as possible. CAUTION If you continue to drive despite the...
Page 351: Breaking-In Of New Brake Pads And Linings
& Breaking-in of new brake pads and linings When replacing the brake pad or lining, use only genuine SUBARU parts. After replacement, the new parts must be broken in as follows. ! Brake pad and lining...
Page 352: Tires And Wheels
Tires and wheels & Types of tires You should be familiar with type of tires present on your vehicle. ! All season tires All season tires are designed to provide an adequate measure of traction, handling and braking performance in year-round driving including snowy and icy road conditions.
Page 353: Tire Inspection
Maintenance and service the tire pressure monitoring system may not be functioning normally. In this event, go to a SUBARU dealer to have the system inspected as soon as possible. While the vehicle is driven, friction be- tween tires and the road surface causes the tires to warm up.
Page 354: Tire Pressures And Wear
Drive slowly to the nearest authorized SUBARU dealer and have the vehicle inspected. & Tire pressures and wear Maintaining the correct tire pressures helps to maximize the tires’...
Page 355 11-36 Maintenance and service Correct tire pressure (tread worn evenly) Roadholding is good, and steering is responsive. Rolling resistance is low, so fuel consumption is also lower. Abnormally low tire pressure (tread worn at shoulders) Rolling resistance is high, so fuel con- sumption is also higher.
Page 356: Wheel Balance
If you suspect that the wheels are not correctly balanced, have them checked and adjusted by your SUBARU dealer. Also have them adjusted after tire repairs and after tire rotation. NOTE...
Page 357: Tire Rotation
(tread pattern), con- struction, and size. You are advised to replace the tires with new ones that are identical to those fitted as standard equip- ment. For safe vehicle operation, SUBARU recommends replacing all four tires at the same time.
Page 358: Wheel Replacement
Never let the wheel rub against sharp protrusions or curbs. When wheel nuts, balance weights, or the center cap is replaced, be sure to replace them with genuine SUBARU parts designed for aluminum wheels.
Page 359: Windshield Washer Fluid
In areas where water freezes in winter, use an anti-freeze type windshield washer fluid. SUBARU Windshield Washer Fluid contains 58.5% methyl alcohol and 41.5% surfactant, by volume. Its freezing tem- perature varies according to how much it is diluted, as indicated in the following table.
Page 360: Replacement Of Wiper Blades
a different concentration from the one used previously, purge the old fluid from the piping between the reservoir tank and washer nozzles by operating the washer for a certain period of time. Otherwise, if the concentration of the fluid remaining in the piping is too low for the outside temperature, it may freeze and block the nozzles.
Page 361: Windshield Wiper Blade Assembly
11-42 Maintenance and service & Windshield wiper blade as- sembly ! Type A 1. Raise the wiper arm off the windshield. Stopper 2. Remove the wiper blade assembly by holding its pivot area and pushing it in the direction shown by the arrow while de- pressing the wiper blade stopper.
Page 362: Rear Window Wiper Blade Assembly
Metal spines 2. If the new blade rubber is not provided with two metal spines, remove the metal spines from the old blade rubber and install them in the new blade rubber. 3. Align the claws of the metal support with the grooves in the rubber and slide the blade rubber assembly into the metal support until it locks.
Page 363: Rear Window Wiper Blade Rubber
11-44 Maintenance and service 3. Pull the wiper blade assembly toward you to remove it from the wiper arm. 4. Install the wiper blade assembly to the wiper arm. Make sure that it locks in place. 5. Hold the wiper arm by hand and slowly lower it in position.
Page 364: Battery
4. Align the claws of the plastic support with the grooves in the blade rubber assembly, then slide the blade rubber assembly into place. Securely retain both ends of the rubber with the stoppers on the plastic support ends. If the rubber is not retained properly, the wiper may scratch the rear window glass.
Page 365: Fuses
11-46 Maintenance and service remove rings, metal watchbands, and other metal jewelry. Never allow metal tools to contact the positive battery terminal and any- thing connected to it WHILE you are at the same time in contact with any other metallic portion of the vehicle because a short cir- cuit will result.
Page 366 4. Pull out the fuse with the fuse puller. 5. Inspect the fuse. If it has blown, replace it with a spare fuse of the same rating. 6. If the same fuse blows again, this indicates that its system has a problem. Contact your SUBARU dealer for repairs.
Page 367: Main Fuse
If a main fuse blows after it is replaced, have the electrical system checked by your nearest SUBARU dealer. Installation of accessories Always consult your SUBARU dealer before installing fog lights or any other electrical equipment in your vehicle.
Page 368: Headlights (Models Without Hid Headlights)
NOTE If headlight aiming is required, con- sult your SUBARU dealer for proper adjustment of the headlight aim. It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 369 11-50 Maintenance and service 3. Remove the bulb cover, by turning it counterclockwise. 4. Disconnect the electrical connector from the bulb. 5. Remove the bulb from the headlight assembly by turning it counterclockwise. 6. Replace the bulb with a new one. At this time, do not touch the bulb surface.
Page 370: Front Turn Signal Light
Maintenance and service & Front turn signal light It may be difficult to replace the bulbs. Have the bulbs replaced by your SUBARU dealer if necessary. & Front fog light (if equipped) It may be difficult to replace the bulbs.
Page 371 11-52 Maintenance and service Brake/tail and rear side marker light Rear turn signal light Back-up light 3. Remove the bulb socket from the rear combination light assembly by turning it counterclockwise. 4. Pull the bulb out of the bulb socket and replace it with a new one.
Page 372: Back-Up Light (5-Door)
6. Put the rear combination light assem- bly into place while aligning the clip with the guide on the vehicle. 7. Tighten the upper and lower screws. & Back-up light (5-door) 1. Apply a flat-head screwdriver to the light cover as shown in the illustration, and pry the light cover off from the rear gate trim.
Page 373: License Plate Light
11-54 Maintenance and service & License plate light 1. Insert a finger into the right side of the license plate light cover, then press once to the left and pull out to remove the cover. 2. Turn the bulb socket counterclockwise and pull out the socket.
Page 374: Dome Light And Cargo Area Light
! Type B 1. Remove the lens by prying the edge of the lens with a flat-head screwdriver. 2. Pull the bulb out of the socket. 3. Install a new bulb. 4. Reinstall the lens. & Dome light and cargo area light Dome light Cargo area light...
Page 375: High Mount Stop Light (4-Door)
3. Pull the bulb out of the socket. 4. Install a new bulb. 5. Reinstall the cover. & Other bulbs Other bulbs may be difficult to replace. Have the bulbs replaced by your SUBARU dealer if necessary.
Page 376 Specifications ... 12-2 Dimensions... Engine ... Electrical system... Capacities ... Tires ... Wheel alignment ... Fuses and circuits ... 12-2 Fuse panel located in the passenger compartment ... 12-3 Fuse panel located in the engine 12-3 compartment ... 12-4 Bulb chart... 12-5 Vehicle identification ...
Page 377: Specifications
12-2 Specifications Specifications These specifications are subject to change without notice. & Dimensions 4-door Item Non-turbo models Turbo models Overall length 180.3 (4,580) Overall width Overall height 58.1 (1,475) Wheel base Tread Front 58.9 (1,495) 58.9 (1,495)* Rear 59.1 (1,500) 59.1 (1,500)* Ground clearance* *1: Measured with vehicle empty...
Page 378: Engine
& Engine Engine model EJ253 (2.5 L, SOHC, non-turbo) Engine type Displacement cc (cu-in) Bore Stroke in (mm) Compression ratio 10.0 : 1 Firing order & Electrical system Battery type and capacity (5HR) Alternator Non-turbo models Turbo models Non-turbo models Spark plugs Turbo models AT: Automatic transmission...
Page 379: Capacities
12-4 Specifications & Capacities Fuel tank Engine oil Transmission oil 5-speed (MT models) 6-speed Transmission fluid (AT models) Front differential gear oil (AT models) Rear differential gear oil Power steering fluid Engine coolant Non-turbo models Turbo models except WRX STI WRX STI AT: Automatic transmission MT: Manual transmission...
Page 380: Tires
& Tires Tire size P205/55R16 89V Wheel size Pressure Front Rear Temporary Size spare tire Pressure & Wheel alignment Item 4-door Non-turbo models Turbo models Front Rear Camber Front –1 05’ Rear P205/50R17 88V 225/45R17 7 JJ 33 psi (230 kPa, 2.3 kgf/cm 32 psi (220 kPa, 2.2 kgf/cm T125/70 D17 60 psi (420 kPa, 4.2 kgf/cm...
Page 381: Fuses And Circuits
12-6 Specifications Fuses and circuits & Fuse panel located in the passenger compartment Fuse Fuse Circuit panel rating Empty Empty Door locking Front wiper deicer relay Combination meter Clock 7.5A Remote control rear view mirrors Seat heater relay Combination meter Integrated unit Stop light Front wiper deicer...
Page 382 Fuse Fuse Circuit panel rating Illumination Seat heaters Back-up light Empty Accessory power outlet (instrument panel) 7.5A Starter relay Air conditioner Rear window defogger relay coil Rear wiper Rear window washer Audio unit SRS airbag system 7.5A Power window relay Radiator main fan relay Blower fan Blower fan...
Page 383: Fuse Panel Located In The Engine Compartment
12-8 Specifications & Fuse panel located in the engine compartment Main fuse Fuse Fuse Circuit panel rating ABS unit Vehicle Dynamics Con- trol unit Main fan (cooling fan) Secondary air combina- tion valve (turbo models) Sub fan (cooling fan) Empty Empty Headlight (low beam) Headlight (high beam)
Page 384 Fuse Fuse Circuit panel rating Headlight (right side) Headlight (left side) 12-9 Specifications...
Page 385: Specifications
12-10 Specifications Bulb chart NOTE Lights from A to C are the LED (Light Emitting Diode) type. Consult your SUBARU dealer for replacement.
Page 386 – 12V-5W self. 12V-5W – Do not remove any headlight- 12V-21W (WY21W) assembly components by yourself. 12V-21W 7440 For replacement, contact your 12V-5W 168 (W5W) SUBARU dealer. – – – – – – 12-11 Specifications WARNING – CONTINUED –...
Page 387 12-12 Specifications CAUTION Replace any bulb only with a new bulb of the specified wattage. Using a bulb of different wattage could result in a fire.
Page 388: Vehicle Identification
Vehicle identification 12-13 Specifications Vehicle identification number Emission control label Tire inflation pressure label Certification label Vehicle identification number plate Model number label Fuel label Air conditioner label...
Page 389 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 390 Consumer information and Reporting safety defects For U.S.A..13-2 Tire information ... 13-2 Tire labeling ... Recommended tire inflation pressure... Glossary of tire terminology ... Tire care – maintenance and safety practices... Vehicle load limit – how to determine... Determining compatibility of tire and vehicle load capacities ...
Page 391: For U.s.a
13-2 Consumer information and Reporting safety defects For U.S.A. The following information has been compiled according to Code of Federal Regulations “Title 49, Part 575”. Tire information & Tire labeling Many markings (e.g. Tire size, Tire Identification Number or TIN) are placed on the sidewall of a tire by tire manufacturers.
Page 392: Consumer Information And Reporting Safety Defects
Example: (6) Load Index: A numerical code which specifies the maximum load a tire can carry at the speed indicated by its speed symbol, at maximum inflation pressure. For example, “90” means 1,323 lbs (600 kg), “89” means 1,278 lbs (580 kg).
Page 393 13-4 Consumer information and Reporting safety defects ! Maximum load rating The load rating at the maximum permissible weight load for this tire. For example, “MAX. LOAD 580 kg (1279 LBS) @ 300 kPa (44 PSI) MAX. PRESS.” WARNING Maximum load rating applies only to the tire, not to the vehicle.
Page 394: Recommended Tire Inflation Pressure
& Recommended tire inflation pressure ! Recommended cold tire inflation pressure Recommended cold tire inflation pressure for your vehicle’s tires is as follows. Tire size P205/55R16 89V P205/50R17 88V Wheel size Pressure Front Rear Temporary Size spare tire Pressure Consumer information and Reporting safety defects 225/45R17 7 JJ 33 psi (230 kPa, 2.3 kgf/cm...
Page 395 13-6 Consumer information and Reporting safety defects ! Vehicle placard The vehicle placard is affixed to the driver’s side B-pillar. Example: U.S.-spec. models Canada-spec. models The vehicle placard shows original tire size, recommended cold tire inflation pressure on each tire at maximum loaded vehicle weight, seating capacity and loading infor- mation.
Page 396: Glossary Of Tire Terminology
& Glossary of tire terminology Accessory weight The combined weight (in excess of those standard items which may be replaced) of automatic transmis- sion, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory-in- stalled equipment (whether in- stalled or not).
Page 397 13-8 Consumer information and Reporting safety defects ing on a vehicle. Light truck (LT) tire A tire designated by its manufac- turer as primarily intended for use on lightweight trucks or multipur- pose passenger vehicles. Load rating The maximum load that a tire is rated to carry for a given inflation pressure.
Page 398 sory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim. Radial ply tire A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread. Recommended inflation pres- sure The cold inflation pressure recom-...
Page 399 13-10 Consumer information and Reporting safety defects accessory weight, and normal oc- cupant weight (distributed in accor- dance with Table 1 that is ap- pended to the end of this section) and dividing by 2. Wheel-holding fixture The fixture used to hold the wheel and tire assembly securely during testing.
Page 400: Tire Care - Maintenance And Safety Practices
& Tire care – maintenance and safety practices Check on a daily basis that the tires are free from serious damage, nails, and stones. At the same time, check the tires for abnormal wear. Inspect the tire tread regularly and replace the tires before their tread wear indicators become visi- ble.
Page 401 13-12 Consumer information and Reporting safety defects ! Calculating total and load ca- pacities varying seating con- figurations Calculate the available load capa- city as shown in the following examples: Example 1A Vehicle capacity weight of the vehicle is 900 lbs (408 kg), which is indicated on the vehicle placard with the statement “The combined weight of occupants and cargo...
Page 402 Calculate the available load ca- pacity. The total weight now exceeds the capacity weight by 92 lbs (42 kg), so the cargo weight must be reduced by 92 lbs (42 kg) or more. Example 2A Vehicle capacity weight of the vehicle is 900 lbs (408 kg), which is indicated on the vehicle placard Consumer information and Reporting safety defects...
Page 403: Determining Compatibility Of Tire And Vehicle Load Capacities
13-14 Consumer information and Reporting safety defects Example 2B For example, if a person weighing 143 lbs (65 kg) and a child weighing 40 lbs (18 kg) now enter the same vehicle (bringing the number of occupants to three), and a child restraint system weighing 11 lbs (5 kg) is installed in the vehicle for the child to use, the calculations are as...
Page 404: Adverse Safety Consequences Of Overloading On Handling And Stopping And On Tires
The GVWR and front and rear GAWRs are determined by not only the maximum load rating of tires but also loaded capacities of the vehi- cle’s suspension, axles and other parts of the body. Therefore, this means that the vehicle cannot necessarily be loaded up to the tire’s maximum load rating on the tire sidewall.
Page 405: Uniform Tire Quality Grading Standards
13-16 Consumer information and Reporting safety defects Uniform tire quality grading standards This information indicates the rela- tive performance of passenger car tires in the area of treadwear, traction, and temperature resis- tance. This is to aid the consumer in making an informed choice in the purchase of tires.
Page 406: Reporting Safety Defects (U.s.a.)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Subaru of America, Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 (TTY: 1-800-424-9153); go to http://www.safercar.gov;...
Page 407 — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —...
Page 408: Index
Index...
Page 409 14-2 Index ABS (Anti-lock Brake System) ... 7-33 Warning light ... 3-24, 7-33 Accessories... 5-4, 11-48 Accessory power outlet... 6-8 Active head restraint... 1-5 Air cleaner element ... 11-17 Air conditioner Automatic climate control system ... 4-10 Manual climate control system... 4-4, 4-7 Air filtration system...
Page 410 System ... 7-32 Brake pedal Free play ... 11-30 Reserve distance ... 11-30 Brake system ... 7-32 Warning light ... 3-24 Braking ... 7-31 Tips... 7-31 Breaking-in of new brake pads and linings ... 11-32 Bulb Chart ... 12-10 Replacing... 11-48 Capacities ...
Page 411 14-4 Index Climate control system Automatic... 4-8 Manual ... 4-3 Clock... 3-32 Clutch Fluid... 11-28 Pedal ... 11-30 Coin tray... 6-5 Coolant... 11-14 Temperature high warning light ... 3-20 Temperature low indicator light... 3-20 Cooling system ... 11-13 Corrosion protection ... 10-4 Cruise control ...
Page 412 Overheating ... 9-13 Starting... 7-9 Stopping ... 7-11 Exterior care... 10-2 Flat tires ... 9-6 Floor mat ... 6-11 Fluid level Automatic transmission ... 11-22 Brake ... 11-27 Clutch... 11-28 Power steering ... 11-26 Fog light Bulb ... 11-51 Indicator light... 3-30 Switch ...
Page 413 14-6 Index Towing and tie-down... 9-14 Horn... 3-48 Hose and connections ... 11-13 Ignition switch... 3-3 Light... 3-5 Illumination brightness control... 3-37 Immobilizer... 2-2 Indicator light (security indicator light) ... 2-3, 3-28 Indicator light Coolant temperature low ... 3-20 Cruise control ... 3-30, 7-51 Cruise control set...
Page 414 Trunk... 11-55 Turn signal ... 3-37, 11-51 Limited slip differential (LSD) ... 7-31 Loading your vehicle ... 8-12 Low fuel warning light ... 3-9, 3-15, 3-25 Low tire pressure warning light ... 3-22 Lower and tether anchorage... 1-31 LSD (Limited slip differential) ... 7-31 Main fuse...
Page 415 14-8 Index Windows... 2-20 Precautions against vehicle modification ... 1-24, 1-61 Preparing to drive ... 7-9 Rear Combination lights... 11-51 Differential gear oil ... 11-24 Gate... 2-24, 9-18 Turn signal light ... 11-51 Viscous limited slip differential ... 7-31 Rear differential Oil temperature warning light ...
Page 416 Warnings ... 2 Seat Fabric... 10-5 Front ... 1-2 Heater ... 1-5 Rear... 1-7 Seatbelt ... 4, 1-11 Fastening... 1-14 Maintenance... 1-20 Pretensioners ... 1-21 Safety tips... 1-11 Warning light and chime ... 1-12, 3-16 Security Alarm system ... 2-14 ID plate...
Page 417 14-10 Index Temporary spare tire ... 9-2 Tether (child restraint system) ... 1-31, 1-34 Tie-down hooks ... 9-14 Tilt steering wheel ... 3-47 Tire ... 11-33, 12-5 Chains... 8-11 Inspection ... 11-34 Pressures and wear ... 11-35 Replacement ... 11-38 Rotation ...
Page 418 Low fuel... 3-9, 3-15, 3-25 Low tire pressure ... 3-22 Oil pressure ... 3-21 Rear differential oil temperature ... 3-22 Seatbelt ... 1-12, 3-16 SRS airbag system ... 3-18 Vehicle Dynamics Control ... 3-27, 7-38 Warranties ... 1 Washing ... 10-2 Waxing and polishing ...
Page 419 134...
Page 420 & Fuel: ! Non-turbo models Use only unleaded gasoline with an octane rating of 87 AKI or higher. ! Turbo models except WRX STI Use premium unleaded gasoline with an octane rating of 91 AKI or higher. If premium unleaded gasoline with an octane rating of 91 AKI is not available, regular unleaded gasoline with octane rating of 87 AKI or higher may be temporarily used.

This manual is also suitable for:

2010 impreza 4-door 2010 impreza 5-door 2010 impreza outback 2010 impreza wrx sti

Subaru 2010 Impreza Owner's Manual

Table of Contents

Seat, Seatbelt and Srs Airbags

Front Seats

Seat Heater (if Equipped)

Rear Seats

Seatbelts

Front Seatbelt Pretensioners

Child Restraint Systems

SRS Airbag (Supplemental Restraint System Airbag)

Keys and Doors

Keys

Immobilizer

Door Locks

Power Door Locking Switches

Remote Keyless Entry System

Alarm System

Child Safety Locks

Windows

Trunk Lid (4-Door)

Rear Gate (5-Door)

Moonroof (if Equipped)

Instruments and Controls

Climate Control

Ventilator

Manual Climate Control System (if Equipped)

Automatic Climate Control System (if Equipped)

Operating Tips for Heater and Air Conditioner

Air Filtration System

Audio

XM TM Satellite Radio Reception (if Equipped)

Antenna System

Installation of Accessories

Audio Set

Power and Sound Controls

FM/AM Radio Operation

Satellite Radio Operation (if Equipped)

CD Player Operation

AUX Unit Operation (if Equipped)

Audio Control Buttons (if Equipped)

Precautions to Observe When Handling a Compact Disc

Interior Equipment

Interior Lights

Storage Compartment

Sun Visors

Cup Holders

Bottle Holders

Accessory Power Outlets

Ashtray (if Equipped)

Shopping Bag Hook (5-Door)

Floor Mat (if Equipped)

Cargo Area Cover (5-Door - if Equipped)

Cargo Tie-Down Hooks (5-Door - if Equipped)

Under-Floor Storage Compartment (if Equipped)

Starting and Operating

Fuel

State Emission Testing (U.S. Only)

Preparing to Drive

Starting the Engine

Stopping the Engine

Remote Engine Start System (Dealer Option)

Driver's Control Center Differential (DCCD) (WRX STI)

Automatic Transmission

Si-Drive (Wrx Sti)

Power Steering

Braking

Limited Slip Differential (LSD) (WRX STI)

ABS (Anti-Lock Brake System)

Electronic Brake Force Distribution (EBD) System

Vehicle Dynamics Control System (if Equipped)

Tire Pressure Monitoring System (TPMS) (U.S.-Spec. Models)

Parking Your Vehicle

Hill Start Assist System (MT Models - if Equipped)

Cruise Control

Quick Links

Chapters

Related Manuals for Subaru 2010 Impreza

Summary of Contents for Subaru 2010 Impreza