Page 1 2009 Pontiac Solstice Owner Manual Seats and Restraint System ... 1-1 Front Seats ... 1-2 Safety Belts ... 1-6 Child Restraints ... 1-22 Airbag System ... 1-36 Restraint System Check ... 1-48 Features and Controls ... 2-1 Keys ... 2-2 Doors and Locks ...
Page 2 GM reserves the right to make changes after that time without further notice. For vehicles ﬁrst sold in Canada, substitute the name “General Motors of Canada Limited” for Pontiac Division wherever it appears in this manual. This manual describes features that may or may not be on your speciﬁc vehicle.
Page 3 Safety Warnings and Symbols A circle with a slash through it is a safety symbol which means “Do Not,” “Do not do this” or “Do not let this happen.” A box with the word CAUTION is used to tell about things that could hurt you or others if you were to ignore the warning.
Page 4 Vehicle Symbols The vehicle has components and labels that use symbols instead of text. Symbols are shown along with the text describing the operation or information relating to a speciﬁc component, control, message, gage, or indicator. : This symbol is shown when you need to see your owner manual for additional instructions or information.
Page 5: Table Of Contents
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Seat Height Adjuster ...1-2 Reclining Seatbacks ...1-3 Seatback Latches ...1-5 Safety Belts ...1-6 Safety Belts: They Are for Everyone ...1-6 How to Wear Safety Belts Properly ...1-11 Lap-Shoulder Belt ...1-18 Safety Belt Use During Pregnancy ...1-21 Safety Belt Extender ...1-21 Child Restraints ...1-22 Older Children ...1-22...
Page 6: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 7: Reclining Seatbacks
Reclining Seatbacks CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you do not want to.
Page 8 CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts cannot do their job when you are reclined like this. The shoulder belt cannot do its job. In a crash, you could go into it, receiving neck or other injuries.
Page 9: Seatback Latches
Seatback Latches The seats have a latch located on the outboard side near the top of the seatback that enables the front seatback(s) to fold forward. To fold the seatback forward, lift the latch and push the seatback forward. CAUTION: If either seatback is not locked, it could move forward in a sudden stop or crash.
Page 10: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This section of the manual describes how to use safety belts properly. It also describes some things not to do with safety belts. CAUTION: Do not let anyone ride where a safety belt cannot be worn properly.
Page 11: Why Safety Belts Work
After more than 40 years of safety belts in vehicles, the facts are clear. In most crashes buckling up does matter... a lot! Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it.
Page 12 Get it up to speed. Then stop the vehicle. The rider does not stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield...
Page 13 or the instrument panel... or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That is why safety belts make such good sense.
Page 14 Questions and Answers About Safety Belts Will I be trapped in the vehicle after a crash if I am wearing a safety belt? You could be — whether you are wearing a safety belt or not. But your chance of being conscious during and after an accident, so you can unbuckle and get out, is much greater if you are belted.
Page 15: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This section is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and infants. If a child will be riding in the vehicle, see Older Children on page 1-22 or Infants and Young Children on page 1-25.
Page 16 What is wrong with this? The shoulder belt is too loose. It will not give as much protection this way. 1-12 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury.
Page 17 What is wrong with this? The lap belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your lap belt is too loose. In a crash, you could slide under the lap belt and apply force on your abdomen.
Page 18 What is wrong with this? The belt is buckled in the wrong buckle. 1-14 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not on the pelvic bones.
Page 19 What is wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied on the abdomen, not on the pelvic bones, and that could cause serious or fatal injuries.
Page 20 What is wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-16 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 21 What is wrong with this? The belt is behind the body. CAUTION: You can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, you would not be restrained by the shoulder belt. Your body could move too far forward increasing the chance of head and neck injury.
Page 22: Lap-Shoulder Belt
What is wrong with this? The belt is twisted across the body. 1-18 CAUTION: You can be seriously injured by a twisted belt. In a crash, you would not have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer/retailer to ﬁx it.
Page 23 If the shoulder portion of a passenger belt is pulled out all the way, the child restraint locking feature may be engaged. If this happens, just let the belt go back all the way and start again. 3. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.
Page 24: Safety Belt Pretensioners
To unlatch the belt, push the button on the buckle. The belt should return to its stowed position. Slide the latch plate up the safety belt webbing when the safety belt is not in use. The latch plate should rest on the stitching on the safety belt, near the guide loop.
Page 25: Safety Belt Use During Pregnancy
Safety Belt Use During Pregnancy Safety belts work for everyone, including pregnant women. Like all occupants, they are more likely to be seriously injured if they do not wear safety belts. A pregnant woman should wear a lap-shoulder belt, and the lap portion should be worn as low as possible, below the rounding, throughout the pregnancy.
Page 26: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-22 The manufacturer’s instructions that come with the booster seat, state the weight and height limitations for that booster. Use a booster seat with a lap-shoulder belt until the child passes the below ﬁt test: •...
Page 27 What is the proper way to wear safety belts? An older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The shoulder belt should not cross the face or neck. The lap belt should ﬁt snugly below the hips, just touching the top of the thighs.
Page 28 CAUTION: Never do this. Never allow a child to wear the safety belt with the shoulder belt behind their back. A child can be seriously injured by not wearing the lap-shoulder belt properly. In a crash, the child would not be restrained by the shoulder belt.
Page 29: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 30 CAUTION: Never do this. Never hold an infant or a child while riding in a vehicle. Due to crash forces, an infant or a child will become so heavy it is not possible to hold it during a crash. For example, in a crash at only 25 mph (40 km/h), a 12 lb (5.5 kg) infant will suddenly become a 240 lb (110 kg) force on a person’s arms.
Page 31 CAUTION: Never do this. Children who are up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Never put a rear-facing child restraint in the right front seat. Secure a rear-facing child restraint in a rear seat.
Page 32 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 33: Child Restraint Systems
CAUTION: A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. Instead, it may settle up around the child’s abdomen. In a crash, the belt would apply force on a body area that is unprotected by any bony structure.
Page 34 A booster seat (C-D) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. A booster seat can also help a child to see out the window. 1-30 Securing an Add-on Child Restraint in the Vehicle CAUTION: A child can be seriously injured or killed in a crash if the child restraint is not properly secured in the...
Page 35: Lower Anchors And Tethers For
Keep in mind that an unsecured child restraint can move around in a collision or sudden stop and injure people in the vehicle. Be sure to properly secure any child restraint in your vehicle — even when no child is in it. Securing the Child Within the Child Restraint CAUTION:...
Page 36: Securing A Child Restraint In The Right Front Seat Position
Refer to your child restraint instructions and instructions in this manual for securing a child restraint using the vehicle’s safety belts. Securing a Child Restraint in the Right Front Seat Position This vehicle has airbags. In addition, the vehicle has a passenger sensing system which is designed to turn off the right front passenger frontal airbag under certain conditions.
Page 37 Rear-facing child restraints should not be installed in the vehicle, even if the airbag is off. If the child restraint has the LATCH system, see Lower Anchors and Tethers for Children (LATCH) on page 1-31 for how to install your child restraint using LATCH.
Page 38 4. Push the latch plate into the buckle until it clicks. 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. Position the release button on the buckle so the safety belt could be quickly unbuckled if necessary. 1-34...
Page 39 6. To tighten the belt, push down on the child restraint, pull the shoulder portion of the belt to tighten the lap portion of the belt and feed the shoulder belt back into the retractor. When installing a forward-facing child restraint, it may be helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 40: Airbag System
Airbag System The vehicle has the following airbags: • A frontal airbag for the driver. • A frontal airbag for the right front passenger. For frontal airbags, the word AIRBAG will appear on the middle part of the steering wheel for the driver and on the instrument panel for the right front passenger.
Page 41 CAUTION: Airbags inﬂate with great force, faster than the blink of an eye. Anyone who is up against, or very close to, any airbag when it inﬂates can be seriously injured or killed. Do not sit unnecessarily close to the airbag, as you would be if you were sitting on the edge of your seat or leaning forward.
Page 42: Where Are The Airbags
Where Are the Airbags? The driver’s frontal airbag is in the middle of the steering wheel. 1-38 The right front passenger’s airbag is in the instrument panel on the passenger’s side.
Page 43: When Should An Airbag Inﬂate
CAUTION: If something is between an occupant and an airbag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating airbag must be kept clear. Do not put anything between an occupant and an airbag, and do not attach or put anything on the steering wheel hub or on or near any other airbag...
Page 44: What Makes An Airbag Inﬂate
Frontal airbags are not intended to inﬂate during vehicle rollovers, rear impacts, or in many side impacts. In any particular crash, no one can say whether an airbag should have inﬂated simply because of the damage to a vehicle or because of what the repair costs were.
Page 45 CAUTION: When an airbag inﬂates, there may be dust in the air. This dust could cause breathing problems for people with a history of asthma or other breathing trouble. To avoid this, everyone in the vehicle should get out as soon as it is safe to do so. If you have breathing problems but cannot get out of the vehicle after an airbag inﬂates, then get fresh air by opening a window or a door.
Page 46: Passenger Sensing System
Passenger Sensing System The vehicle has a passenger sensing system for the right front passenger position. The passenger airbag status indicator will be visible on the instrument panel when the vehicle is started. United States The words ON and OFF, or the symbol for on and off, will be visible during the system check.
Page 47 CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates. This is because the back of the rear-facing child restraint would be very close to the inﬂating airbag. A child in a forward-facing child restraint can be seriously injured or killed if the right front passenger airbag inﬂates and the passenger seat is in a forward...
Page 48 The passenger sensing system is designed to enable (may inﬂate) the right front passenger frontal airbag anytime the system senses that a person of adult size is sitting properly in the right front passenger seat. When the passenger sensing system has allowed the airbag to be enabled, the on indicator will light and stay lit to remind you that the airbag is active.
Page 49: Additional Factors Affecting System Operation
If the Off Indicator is Lit for an Adult-Size Occupant If a person of adult-size is sitting in the right front passenger seat, but the off indicator is lit, it could be because that person is not sitting properly in the seat. If this happens, use the following steps to allow the system to detect that person and enable the right front passenger frontal airbag:...
Page 50: Servicing Your Airbag-Equipped Vehicle
A thick layer of additional material, such as a blanket or cushion, or aftermarket equipment such as seat covers, seat heaters, and seat massagers can affect how well the passenger sensing system operates. We recommend that you not use seat covers or other aftermarket equipment except when approved by GM for your speciﬁc vehicle.
Page 51: Adding Equipment To Your Airbag-Equipped Vehicle
Adding Equipment to Your Airbag-Equipped Vehicle Is there anything I might add to or change about the vehicle that could keep the airbags from working properly? Yes. If you add things that change your vehicle’s frame, bumper system, height, front end or side sheet metal, they may keep the airbag system from working properly.
Page 52: Restraint System Check
Restraint System Check Checking the Restraint Systems Safety Belts Now and then, check the safety belt reminder light, safety belts, buckles, latch plates, retractors, and anchorages are all working properly. Look for any other loose or damaged safety belt system parts that might keep a safety belt system from doing its job.
Page 53: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as...
Page 54 ✍ NOTES 1-50...
Page 55: Features And Controls
Section 2 Keys ...2-2 Remote Keyless Entry (RKE) System ...2-3 Remote Keyless Entry (RKE) System Operation ...2-4 Doors and Locks ...2-6 Manual Door Locks ...2-6 Power Door Locks ...2-6 Delayed Locking ...2-7 Automatic Door Lock ...2-7 Automatic Door Unlock ...2-7 Trunk ...2-8 Windows ...2-10 Manual Windows ...2-11...
Page 56: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. The windows will function with the keys in the ignition and children could be seriously injured or killed if caught in the path of a closing window.
Page 57: Remote Keyless Entry (Rke) System
The key has a bar-coded key tag that a dealer/retailer or qualiﬁed locksmith can use to make new keys. Store this information in a safe place, not in your vehicle. Notice: If you ever lock your keys in the vehicle, you may have to damage the vehicle to get in.
Page 58: Remote Keyless Entry (Rke) System Operation
Remote Keyless Entry (RKE) System Operation The Remote Keyless Entry (RKE) transmitter functions work up to 60 feet (18 m) away from the vehicle. There are other conditions which can affect the performance of the transmitter. See Remote Keyless Entry (RKE) System on page 2-3. (Lock): Press to lock all the doors.
Page 59: Battery Replacement
Programming Transmitters to the Vehicle Only RKE transmitters programmed to the vehicle will work. If a transmitter is lost or stolen, a replacement can be purchased and programmed through your dealer/retailer. When the replacement transmitter is programmed to the vehicle, all remaining transmitters must also be programmed.
Page 60: Doors And Locks
Doors and Locks Manual Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers, especially children, can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 61: Delayed Locking
Delayed Locking A vehicle with power door locks has the delayed locking feature which delays the actual locking of the doors when the Remote Keyless Entry (RKE) transmitter is used to lock the vehicle. If any door is open when locking the vehicle using the RKE transmitter, three chimes will sound signaling that the delayed locking feature is active.
Page 62: Trunk
Trunk To release the trunk lid use either the Remote Keyless Entry (RKE) transmitter, or see “Remote Trunk Release” following. To close the trunk, push down ﬁrmly from the rear center of the trunk lid. CAUTION: Exhaust gases may enter the vehicle if it is driven with the liftgate, trunk/hatch open, or with any objects that pass through the seal between the body and the trunk/hatch or liftgate.
Page 63: Remote Trunk Release
Remote Trunk Release To open the trunk from inside the vehicle, press the remote trunk release button located in the glovebox. The remote trunk release will only work when either the ignition is off or in ACC/ACCESSORY, the parking brake is engaged, or the vehicle speed is less than 2 mph (3 km/h).
Page 64: Windows
Windows CAUTION: Leaving children, helpless adults, or pets in a vehicle with the windows closed is dangerous. They can be overcome by the extreme heat and suffer permanent injuries or even death from heat stroke. Never leave a child, a helpless adult, or a pet alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 65: Manual Windows
Manual Windows On vehicles with manual windows, use the window crank to open and close each window. Power Windows CAUTION: Leaving children in a vehicle with the keys is dangerous for many reasons, children or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move.
Page 66: Sun Visors
The passenger’s door has a window switch that controls that window. Press the front of the switch to open the window. Pull the switch up to close it. Express-Down Window Windows with an express-down feature allow the window to be lowered fully without pressing and holding the switch.
Page 67: How The System Alarm Is Activated
Arming the System While the ignition is off, press the Remote Keyless Entry (RKE) transmitter lock button, to arm the system. The system will arm after either of these things occur: • Thirty seconds after all the doors are closed. •...
Page 68: Pass-Key Iii+ Electronic Immobilizer
® PASS-Key III+ Electronic Immobilizer The PASS-Key III+ system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 69 ® PASS-Key III+ to have a new key made. In an emergency, contact Roadside Assistance. See Roadside Assistance Program on page 7-6, for more information. It may be possible for the PASS-Key to “learn” the transponder value of a new or replacement key.
Page 70: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: The vehicle does not need an elaborate break-in. But it will perform better in the long run if you follow these guidelines for the ﬁrst 500 miles (805 km): • Do not drive at any one constant speed, fast or slow.
Page 71: Retained Accessory Power (Rap)
If you have an automatic transmission, the ignition switch cannot be turned to LOCK/OFF unless the shift lever is in P (Park). If you have a manual transmission, the ignition switch can be turned to LOCK/OFF in any shift lever position. CAUTION: If you have a manual transmission removing the key from the ignition switch will lock the steering...
Page 72: Starting The Engine
Starting the Engine Place the transmission in the proper gear. Automatic Transmission Move the shift lever to P (Park) or N (Neutral). The engine will not start in any other position. To restart the vehicle when it is already moving, use N (Neutral) only. Notice: Do not try to shift to P (Park) if the vehicle is moving.
Page 73 2. If the engine does not start after 5-10 seconds, especially in very cold weather (below 0°F or −18°C), it could be ﬂooded with too much gasoline. Push the accelerator pedal all the way to the ﬂoor and holding it there as you hold the key in START for a maximum of 15 seconds.
Page 74 P (Park): This position locks the rear wheels. It is the best position to use when starting the engine because the vehicle cannot move easily. CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set.
Page 75 Notice: Shifting out of P (Park) or N (Neutral) with the engine running at high speed may damage the transmission. The repairs would not be covered by the vehicle warranty. Be sure the engine is not running at high speed when shifting the vehicle. D (Drive): This position is for normal driving with the automatic transmission.
Page 76 Manual Transmission Operation This is the shift pattern. Here is how to operate the manual transmission: 1 (First): Press the clutch pedal and shift into 1 (First). Then, slowly let up on the clutch pedal as you press the accelerator pedal. You can shift into 1 (First) when the vehicle is traveling less than 20 mph (32 km/h).
Page 77: Parking Brake
Parking Brake The parking brake lever is located between the front seats. To set the parking brake, hold the brake pedal down and pull up on the parking brake lever. If the ignition is on, the brake system warning light will come on. See Brake System Warning Light on page 3-25.
Page 78: Shifting Into Park (Automatic Transmission)
Shifting Into Park (Automatic Transmission) CAUTION: It can be dangerous to get out of the vehicle if the shift lever is not fully in P (Park) with the parking brake ﬁrmly set. The vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 79: Shifting Out Of Park
Torque Lock (Automatic Transmission) If you are parking on a hill and you do not shift your transmission into P (Park) properly, the weight of the vehicle may put too much force on the parking pawl in the transmission. You may ﬁnd it difficult to pull the shift lever out of P (Park).
Page 80: Parking The Vehicle (Manual Transmission)
Parking the Vehicle (Manual Transmission) Before leaving the manual transmission vehicle, fully press the clutch pedal in, move the shift lever in either 1 (First) gear or R (Reverse), and ﬁrmly apply the parking brake. See Manual Transmission Operation on page 2-22.
Page 81: Engine Exhaust
Engine Exhaust CAUTION: Engine exhaust contains Carbon Monoxide (CO) which cannot be seen or smelled. Exposure to CO can cause unconsciousness and even death. Exhaust may enter the vehicle if: • The vehicle idles in areas with poor ventilation (parking garages, tunnels, deep snow that may block underbody airﬂow or tail pipes).
Page 82: Running The Vehicle While Parked
Running the Vehicle While Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 83: Mirrors
Mirrors Manual Rearview Mirror Adjust the mirror to see clearly behind your vehicle. Hold the mirror in the center to move it up or down and side to side. Adjust the mirror to avoid glare from the headlamps behind your vehicle. Move the lever to the right for nighttime use and to the left for daytime use.
Page 84: Onstar System
® OnStar System OnStar uses several innovative technologies and live advisors to provide a wide range of safety, security, information, and convenience services. If the airbags deploy, the system is designed to make an automatic call to OnStar Emergency advisors who can request emergency services be sent to your location.
Page 85 • Roadside Assistance • Stolen Vehicle Location Assistance • Remote Door Unlock/Vehicle Alert • OnStar Vehicle Diagnostic Email • GM Goodwrench On Demand Diagnostics • OnStar Hands-Free Calling with 30 trial minutes • OnStar Virtual Advisor (U.S. Only) OnStar Services Included with Directions &...
Page 86: How Onstar Service Works
OnStar Steering Wheel Controls This vehicle may have a Talk/Mute button that can be used to interact with OnStar Hands-Free Calling. See Audio Steering Wheel Controls on page 3-79 for more information. On some vehicles, the mute button can be used to dial numbers into voice mail systems, or to dial phone extensions.
Page 87: Storage Areas
Storage Areas Glove Box Lift the glove box handle up to open it. Use the key to lock and unlock the glove box. Cupholders There is a cupholder on the passenger side of the center console. Press and release the forward section of the cupholder to access it.
Page 88: Removing The Roof Panel
Removing the Roof Panel CAUTION: Do not try to remove a roof panel while the vehicle is moving. Trying to remove the roof panel while the vehicle is moving could cause an accident. The panel could fall into the vehicle and cause you to lose control, or it could ﬂy off and strike another vehicle.
Page 89: Storing The Roof Panel
The driver’s side handle moves toward the driver’s door. The passenger’s side handle moves toward the passenger’s door. 4. To unlock the rear of the roof panel’s rear release latch, press the back of the release handle (B). Then press the button on the front of the release handle (A) with...
Page 90: Installing The Roof Panel
Installing the Roof Panel CAUTION: An improperly attached roof panel may fall into or ﬂy off the vehicle. You or others could be injured. After installing the roof panel, always check that it is ﬁrmly attached by pushing up on the underside of the panel.
Page 91: Convertible Top
Convertible Top For care and cleaning of the convertible top, see Convertible Top on page 5-95 under “Service and Appearance Care”. High pressure car washes may cause water to enter the vehicle. A clear protective ﬁlm has been installed on the trunk lid surface under the convertible top buttresses.
Page 92 Notice: Lowering the top if it is damp, wet, or dirty can cause stains, mildew, and damage to the inside of your vehicle. Dry off the top before lowering it. Notice: If you lower the top on your vehicle in cold weather (0°F/-18°C or lower), you may damage top components.
Page 93 6. Pull rearward on the side edge (B) of the convertible top and pull it off of the windshield frame. 7. Push the convertible top down into the trunk (E). 8. After the top is stored, as shown, push on the convertible top to ensure that the top is fully retracted and securely stored.
Page 94 6. Pull the front edge (A) of the convertible top forward from the outside of the vehicle, or push the front edge (A) of the convertible top forward from the inside of the vehicle. 7. Turn the top front latch handle clockwise to latch the convertible top.
Page 95 Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-5 Horn ...3-5 Tilt Wheel ...3-6 Turn Signal/Multifunction Lever ...3-6 Turn and Lane-Change Signals ...3-7 Headlamp High/Low-Beam Changer ...3-7 Flash-to-Pass ...3-7 Windshield Wipers ...3-8 Windshield Washer ...3-9 Cruise Control ...3-9 Headlamps ...3-12 Headlamps on Reminder ...3-13 Daytime Running Lamps (DRL) ...3-13 Fog Lamps ...3-13...
Page 96 Section 3 Driver Information Center (DIC) ...3-34 DIC Operation and Displays ...3-35 DIC Warnings and Messages ...3-37 DIC Vehicle Personalization ...3-41 Audio System(s) ...3-46 Setting the Clock ...3-47 Radio(s) ...3-49 Using an MP3 ...3-60 Instrument Panel XM Radio Messages ...3-67 ®...
Page 97 ✍ NOTES...
Page 98: Instrument Panel Overview
Instrument Panel Overview...
Page 99: Hazard Warning Flashers
The main components of the instrument panel are the following: A. Side Window Outlets. See Climate Control System on page 3-16. B. Outlet Adjustment on page 3-19. C. Turn Signal/Multifunction Lever on page 3-6. D. Cruise Control on page 3-9 (If Equipped). E.
Page 100: Tilt Wheel
Tilt Wheel A tilt wheel lets the steering wheel be adjusted. The tilt lever is located on the left side of the steering column. To tilt the wheel, pull the lever down. Raise or lower the wheel to a comfortable position, then pull the lever up to lock the wheel in place.
Page 101: Turn And Lane-Change Signals
Turn and Lane-Change Signals An arrow on the instrument panel cluster ﬂashes in the direction of the turn or lane change. Move the lever all the way up or down to signal a turn. Raise or lower the lever until the arrow starts to ﬂash to signal a lane change.
Page 102: Windshield Wipers
Windshield Wipers The windshield wiper lever is located on the right side of the steering wheel. Move the lever to control the windshield wipers. (Off): Turns off the windshield wipers. & (Intermittent; Speed Sensitive Wipers): For intermittent or speed sensitive operation. The amount of delay time varies between wiping cycles due to the delay setting selected or the speed of the vehicle.
Page 103: Windshield Washer
Heavy snow or ice can overload the wiper motor. A circuit breaker stops the motor until it cools. If the motor gets stuck, turn the wipers off, clear away the snow or ice, and then turn the wipers back on. As an added safety feature, if the wipers are on for more than 15 seconds, the vehicle’s headlamps turn on automatically.
Page 104: Setting Cruise Control
Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 105 Increasing Speed While Using Cruise Control There are two ways to increase speed. 1. Disengage the cruise control by applying the brake pedal but do not turn it off. Accelerate to a higher speed and reset the cruise control. 2. If the cruise control system is already engaged, press the RES+ button.
Page 106: Headlamps
Erasing Speed Memory The cruise control set speed memory is erased when the cruise control or the ignition is turned off. Headlamps The lever on the left side of the steering column operates the exterior lamps. The exterior lamp switch has the following four positions: (Headlamps): Turns on the headlamps, parking lamps, and taillamps.
Page 107: Headlamps On Reminder
Headlamps on Reminder If the drivers door is opened with the ignition off and the lamps on, a warning chime will sound. This indicates that the headlamps are still on. Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day.
Page 108: Instrument Panel Brightness
Instrument Panel Brightness The control for this feature is located on the instrument panel to the right of the steering wheel. Instrument Panel Brightness: Turn the knob clockwise or counterclockwise to brighten or dim the lights. Entry/Exit Lighting The lamps inside the vehicle come on when any door is opened.
Page 109: Ashtray(S) And Cigarette Lighter
Certain electrical accessories may not be compatible with the accessory power outlet and could result in blown vehicle or adapter fuses. If you experience a problem, see your dealer/retailer for additional information on the accessory power outlet. Notice: Adding any electrical equipment to the vehicle can damage it or keep other components from working as they should.
Page 110: Climate Controls
Climate Controls Climate Control System Climate Control System with Air Conditioning shown, Climate Control System without Air Conditioning similar A. Temperature D. Air Conditioning Control E. Recirculation B. Fan Control F. Rear Window C. Air Delivery Mode Defogger Control 3-16 The heating and ventilation of the vehicle can be controlled with this system.
Page 111 (Floor): Air is directed to the ﬂoor outlets, with some directed to the side window and defroster outlets. If low or no airﬂow is on the passenger side, make sure that the carpet covering is tucked under ﬂoor outlets. (Floor/Defog): This mode clears the windows of fog or moisture.
Page 112: Rear Window Defogger
Using these settings together for long periods of time can cause the air inside of the vehicle to become too dry. To prevent this from happening, after the air in the vehicle has cooled, turn the recirculation mode off. The air conditioning system removes moisture from the air, so a small amount of water might drip under the vehicle while idling or after turning off the engine.
Page 113: Outlet Adjustment
Outlet Adjustment Use the air outlets located in the center and on the side of the instrument panel to direct the airﬂow. The vehicle has air outlets that allow you to adjust the direction and amount of airﬂow inside the vehicle. Move the louvers up or down or turn them clockwise or counterclockwise to change the direction of the airﬂow.
Page 114: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to show how the vehicle is running. It shows how fast the vehicle is going, about how much fuel is left in the tank, and many other things needed to drive safely and economically. United States Cluster shown, Canada and Turbo model similar 3-20...
Page 115: Speedometer And Odometer
Speedometer and Odometer The speedometer shows the vehicle’s speed in both miles per hour (mph) and kilometers per hour (km/h). The vehicle’s odometer works together with the Driver Information Center (DIC). For vehicles with a Trip A and Trip B odometer, it can be set. See “Trip Information”...
Page 116: Safety Belt Reminders
Safety Belt Reminders Safety Belt Reminder Light When the engine is started, a chime sounds for several seconds to remind a driver to fasten the safety belt, unless the driver safety belt is already buckled. The safety belt light comes on and stays on for several seconds, then ﬂashes for several more.
Page 117: Airbag Readiness Light
Airbag Readiness Light The system checks the airbag’s electrical system for possible malfunctions. If the light stays on it indicates there is an electrical problem. The system check includes the airbag sensor, the pretensioners, the airbag modules, the wiring and the crash sensing and diagnostic module.
Page 118: Passenger Airbag Status Indicator
Passenger Airbag Status Indicator The vehicle has the passenger sensing system. See Passenger Sensing System on page 1-42 for important safety information. The instrument panel has a passenger airbag status indicator. United States When the vehicle is started, the passenger airbag status indicator will light ON and OFF, or the symbol for on and off, for several seconds as a system check.
Page 119: Charging System Light
Charging System Light This light comes on brieﬂy when the ignition key is turned to START, but the engine is not running, as a check to show it is working. If it does not, have the vehicle serviced by your dealer/retailer.
Page 120: Antilock Brake System (Abs) Warning Light
If the light comes on while driving, pull off the road and stop carefully. Make sure the parking brake is fully released. The pedal might be harder to push or, the pedal could go closer to the ﬂoor. It can take longer to stop.
Page 121: Electronic Stability Control (Esc)/Traction
Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light The Electronic Stability Control (ESC) system or the Traction Control System (TCS) indicator/warning light comes on brieﬂy when the engine is started. If it does not, have the vehicle serviced by the dealer/retailer.
Page 122: Engine Coolant Temperature Warning Light
Engine Coolant Temperature Warning Light This light comes on brieﬂy while starting the vehicle. If it does not, have the vehicle serviced by the dealer/retailer. If the system is working normally the indicator light goes off. Notice: Driving with the engine coolant temperature warning light on could cause the vehicle to overheat.
Page 123: Tire Pressure Light
Tire Pressure Light For vehicles with a tire pressure light, this light comes on brieﬂy when the engine is started and provides information about tire pressures and the Tire Pressure Monitoring System. When the Light is On Steady This indicates that one or more of the tires is signiﬁcantly underinﬂated.
Page 124 If the check engine light comes on and stays on, while the engine is running, this indicates that there is an OBD II problem and service is required. Malfunctions often are indicated by the system before any problem is apparent. Heeding the light can prevent more serious damage to the vehicle.
Page 125 An emission system malfunction might be corrected by doing the following: • Make sure the fuel cap is fully installed. See Filling the Tank on page 5-8. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 126: Maintenance Schedule
This can take several days of routine driving. If this has been done and the vehicle still does not pass the inspection for lack of OBD II system readiness, your dealer/retailer can prepare the vehicle for inspection. Oil Pressure Light CAUTION: Do not keep driving if the oil pressure is low.
Page 127: Highbeam On Light
Highbeam On Light This light comes on when the high-beam headlamps are in use. See Headlamp High/Low-Beam Changer on page 3-7 for more information. Trunk Ajar Light This light will come on and a chime will sound if the trunk is ajar. Fuel Gage The fuel gage shows how much fuel the vehicle...
Page 128: Low Fuel Warning Light
• The gage moves a little while turning a corner or speeding up. • The gage does not go back to empty when the ignition is turned off. For the fuel tank capacity, see Capacities and Speciﬁcations on page 5-104. Low Fuel Warning Light This light, below the fuel gage, comes on brieﬂy...
Page 129: Dic Operation And Displays
DIC Operation and Displays The DIC comes on when the ignition is on. The DIC has different modes which can be accessed by pressing the DIC buttons. The button functions are detailed in the following. Information Modes INFO (Information): Press this button to scroll through the following vehicle information modes: Odometer Press the information button until the odometer displays.
Page 130: Oil Life
MPG (L/100 KM) INST (Instantaneous) Press the information button until MPG (L/100 KM) INST displays. This mode shows the current fuel economy at a particular moment and changes frequently as driving conditions change. This mode shows the instantaneous fuel economy in miles per gallon (mpg) or liters per 100 kilometers (L/100 km).
Page 131: Brake Fluid
BOOST (Turbo Only) If your vehicle has this feature, press the information button until BOOST displays. This mode shows a graphic that indicates the amount of boost the engine is receiving in either pounds per square inch (psi) or kilopascals (kPa). DIC Warnings and Messages These messages appear if there is a problem detected in one of your vehicle’s systems.
Page 132 soon as you can. Have the tire pressures checked and set to those shown on the Tire Loading Information label. See Tires on page 5-47, Loading the Vehicle on page 4-20, and Inﬂation - Tire Pressure on page 5-53. The DIC also shows the tire pressure values. See DIC Operation and Displays on page 3-35.
Page 133: Service Air Bag
ESC (Electronic Stability Control) NOT READY If your vehicle has Electronic Stability Control (ESC), this message may display brieﬂy after starting the vehicle if the system’s sensors are not yet calibrated. The system is not functional until the message stops displaying. Adjust your driving accordingly. When the message is no longer displayed, the system is functional.
Page 134 SERVICE ESC (ELECTRONIC STABILITY CONTROL) If your vehicle has Electronic Stability Control (ESC), this message displays and a chime sounds if there has been a problem detected with ESC. The ESC/TCS light also appears on the instrument panel cluster. This light stays on solid as long as the detected problem remains present.
Page 135: Dic Vehicle Personalization
TRACTION OFF If your vehicle has the Traction Control System (TCS), this message displays and the ESC/TCS light on the instrument panel cluster comes on solid when the TCS is turned off. Adjust your driving accordingly. See Traction Control System (TCS) on page 4-8 and Electronic Stability Control (ESC)/Traction Control System (TCS) Indicator/Warning Light on page 3-27 for more information.
Page 136 UNITS This feature allows you to select the units of measurement in which the DIC will display the vehicle information. When UNITS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ENGLISH (default in United States): All information will be displayed in English units.
Page 137 UNLOCK HORN If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s horn to chirp on the ﬁrst press of the unlock button on the RKE transmitter, can be enabled or disabled. When UNLOCK HORN appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF (default): The horn will not chirp when the unlock...
Page 138 AUTO UNLK (Unlock) This feature, which allows the vehicle to automatically unlock certain doors, can be enabled or disabled. When AUTO UNLK appears on the display, press and hold the reset button for at least one second to scroll through the available settings: ALL (default): All of the doors will automatically unlock.
Page 139 EXT (Exterior) LIGHTS If your vehicle has Remote Keyless Entry (RKE), this feature, which allows the vehicle’s exterior perimeter lighting to turn on each time the unlock button on the RKE transmitter is pressed, can be enabled or disabled. When EXT LIGHTS appears on the display, press and hold the reset button for at least one second to scroll through the available settings: OFF: The exterior perimeter lighting will not turn on...
Page 140: Audio System(S)
Audio System(s) Determine which radio the vehicle has and read the following pages to become familiar with its features. CAUTION: Taking your eyes off the road for extended periods could cause a crash resulting in injury or death to you or others. Do not give extended attention to entertainment tasks while driving.
Page 141: Setting The Clock
Setting the Clock Without Date Display AM/FM Base Radio with a Single CD Player To set the time: 1. Turn the ignition key to ACC/ACCESSORY or ON/RUN. Press to turn the radio on. 2. Press until the hour begins ﬂashing on the display.
Page 142 To change the time default setting from 12 hour to 24 hour or to change the date default setting from month/day/year to day/month/year: 1. Press and then the softkey located below the forward arrow label. Once the time 12H and 24H, and the date MM/DD/YYYY (month, day, and year) and DD/MM/YYYY (day, month, and year) displays.
Page 143: Radio(S)
Radio(s) Radio with CD (MP3) and USB Port shown, Radio with CD (MP3) similar, Radio with Six-Disc CD (MP3) similar Radio with CD (Base) The vehicle has one of these radios as its audio system. 3-49...
Page 144: Playing The Radio
Radio Data System (RDS) The radio may have RDS. The RDS feature is available for use only on FM stations that broadcast RDS information. This system relies upon receiving speciﬁc information from these stations and only works when the information is available. While the radio is tuned to an FM-RDS station, the station name or call letters display.
Page 145: Storing Radio Stations
• To scan preset stations in the selected band, press © and hold SEEK for four seconds until a double beep sounds. The radio goes to a stored preset, plays for a few seconds, then goes to the next © stored preset.
Page 146 FAV (Favorites): A maximum of 36 stations can be stored as favorites using the six softkeys located below the radio station frequency tabs and by using the radio favorites page button (FAV button). Press FAV to go through up to six pages of favorites, each having six favorite stations available per page.
Page 147: Setting The Tone
Storing a Radio Station as a Preset Radios that have numbered pushbuttons store radio stations as presets. If the radio does not have XM, up to 18 stations (six FM1, six FM2, and six AM), can be programmed on the six numbered buttons. To store preset stations: 1.
Page 148: Adjusting The Speakers (Balance/Fade)
EQ (Equalization): Press this button to select preset equalization settings. To return to the manual mode, press EQ until Manual displays or start to manually adjust the bass, midrange, or treble by pressing Adjusting the Speakers (Balance/Fade) Depending on which radio the vehicle has, the Balance/Fade can be adjusted using To adjust balance or fade using 1.
Page 149: Radio Messages
4. To go to the previous or to the next XM station within the selected category, do one of the following: • Turn • Press the softkeys below the right or left arrows on the radio display. © ¨ • Press SEEK or SEEK.
Page 150: Loading A Cd
Loading a CD Radio’s with a Single CD Player Insert a CD partway into the slot, label side up. The player pulls it in and the CD begins playing. When the CD is inserted, the CD symbol displays. As each new track starts to play, the track number displays. The CD player can play the smaller 3 inch (8 cm) single CDs with an adapter ring.
Page 151: Playing A Cd
Playing a CD If the ignition or radio is turned off with a CD in the player it stays in the player. When the ignition or radio is turned on, the CD starts to play where it stopped, if it was the last selected audio source.
Page 152: Care Of The Cd Player
Playing an MP3 CD-R or CD-RW Disc The radio may have the ability to play an MP3 CD-R or CD-RW disc. See Using an MP3 on page 3-60 for more information. CD Messages CHECK DISC: If an error message displays and/or the CD comes out, it could be for one of the following reasons: •...
Page 153 Using the Auxiliary Input Jack The radio system may have an auxiliary input jack located on the lower right side of the faceplate. This is not an audio output; do not plug the headphone set into the front auxiliary input jack. An external audio ®...
Page 154: Using An Mp3
Make sure the iPod has the latest ﬁrmware from ® Apple for proper operation. iPod ﬁrmware can be ® updated using the latest iTunes apple.com/itunes. Using an MP3 Format Radios that have the capability of playing MP3’s can play .mp3 ﬁles that were recorded onto a CD-R or CD-RW disc.
Page 155 Root Directory The root directory is treated as a folder. Files are stored in the root directory when the disc or storage device does not contain folders. Files accessed from the root directory of a CD display as F1 ROOT. Empty Folder Folders that do not contain ﬁles are skipped, and the player advances to the next folder that contains ﬁles.
Page 156 Playing a CD-R or CD-RW MP3 (Tune): Turn to select MP3 ﬁles on the CD currently playing. © SEEK: Press to go to the start of the track, if more than ten seconds have played. Press and hold or press multiple times to continue moving backward through tracks.
Page 157 To listen to ﬁles by another artist, press the softkey located below either arrow tab. The disc goes to the next or previous artist in alphabetical order. Continue pressing either softkey below the arrow tab until the desired artist displays. To change from playback by artist to playback by album: 1.
Page 158 Using the Radio to Control a USB Storage Device or iPod The radio can control a USB storage device or an iPod using the radio buttons and knobs and display song information on the radio’s display. (Tune): Turn to select ﬁles. ©...
Page 159 3. Press to select the desired folder. If there is more then one folder, repeat Steps 1 and 2 until the desired folder is reached. 4. Turn to scroll through the ﬁles in the selected folder. 5. Press to select the desired ﬁle to be played. To skip through large lists, the ﬁve softkeys can be used to navigate in the following order: •...
Page 160 Repeat Functionality To use Repeat: " Press the softkey below Repeat All and Repeat Track. " (Repeat All): Press the softkey below all tracks. The tab appears lowered when Repeat All is being used. This is the default mode when a USB storage device or iPod is ﬁrst connected.
Page 161: Xm Radio Messages
XM Radio Messages XL (Explicit Language Channels): These channels, or any others, can be blocked at a customer’s request, by calling 1-800-852-XMXM (9696). XM Updating: The encryption code in the receiver is being updated, and no action is required. This process should take no longer than 30 seconds.
Page 162: Bluetooth
XM Not Available: If this message does not clear within a short period of time, the receiver could have a fault. Consult with your dealer/retailer. ® Bluetooth Vehicles with a Bluetooth system can use a Bluetooth capable cell phone with a Hands Free Proﬁle to make and receive phone calls.
Page 163 connected, calls will be made using OnStar Hands-Free Calling, if available. Refer to the OnStar owner’s guide for more information. Pairing Information: • Up to ﬁve cell phones can be paired to the in-vehicle Bluetooth system. • The pairing process is disabled when the vehicle is moving.
Page 164 3. Say “List”. The system lists all the paired Bluetooth devices. If a phone is connected to the vehicle, the system will say “Is connected” after the connected phone. Deleting a Paired Phone 1. Press and hold for two seconds. The system responds with “Ready”...
Page 165 3. Say the complete phone number to be stored at once with no pauses. • If the system recognizes the number it responds with “OK, Storing” and repeats the phone number. • If the system is unsure it recognizes the phone number, it responds with “Store”...
Page 166 5. Say a name tag for the phone number. The name tag is recorded and the system responds with “About to store <name tag>. Does that sound OK?”. • If the name tag does not sound correct, say “No” and repeat Step 5. •...
Page 167: Making A Call
Using the Delete All Name Tags Command The delete all name tags command deletes all stored phone book name tags and route name tags for OnStar, if present. To use the delete all name tags command: 1. Press and hold for two seconds.
Page 168 4. Continue entering digits until the number to be dialed is complete. After the whole number has been entered, say “Dial”. The system responds with “OK, Dialing” and dials the number. • If an unwanted number is recognized by the system, say “Clear”...
Page 169: Receiving A Call
Receiving a Call When an incoming call is received, the audio system mutes and a ring tone is heard in the vehicle. • Press and begin speaking to answer the call. • Press to ignore a call. Call Waiting Call waiting must be supported on the Bluetooth phone and enabled by the wireless service carrier to work.
Page 170 Muting a Call During a call, all sounds from inside the vehicle can be muted so that the person on the other end of the call cannot hear them. To Mute a call 1. Press . The system responds with “Ready” followed by a tone.
Page 171 Voice Pass-Thru Voice Pass-Thru allows access to the voice recognition commands on the cell phone. See the cell phone manufacturers user guide to see if the cell phone supports this feature. This feature can be used to verbally access contacts stored in the cell phone. 1.
Page 172: Other Information
3. Say the name tag to send. • If the system clearly recognizes the name tag it responds with “OK, Sending <name tag>” and the dial tones are sent and the call continues. • If the system is not sure it recognized the name tag properly, it responds “Dial <name tag>, Please say yes or no?”...
Page 173: Audio Steering Wheel Controls
Audio Steering Wheel Controls Vehicles with audio steering wheel controls could differ depending on the vehicle’s options. Some audio controls can be adjusted at the steering wheel. − (Volume): Press to increase or to decrease the radio volume. (Next / Previous): Press to change radio stations, select tracks on a CD, or to select tracks and ®...
Page 174: Radio Reception
(End): Press to reject an incoming call, or end a current call. (Mute / Voice Recognition): Press to silence the vehicle speakers only. Press again to turn the sound on. ® For vehicles with OnStar or Bluetooth systems press and hold for longer than two seconds to interact with those systems.
Page 175: Fixed Mast Antenna
Cellular Phone Usage Cellular phone usage may cause interference with the vehicle’s radio. This interference may occur when making or receiving phone calls, charging the phone’s battery, or simply having the phone on. This interference causes an increased level of static while listening to the radio.
Page 176 ✍ NOTES 3-82...
Page 177: Driving Your Vehicle
Section 4 Your Driving, the Road, and the Vehicle ...4-2 Driving for Better Fuel Economy ...4-2 Defensive Driving ...4-2 Drunk Driving ...4-3 Control of a Vehicle ...4-3 Braking ...4-4 Antilock Brake System (ABS) ...4-4 Braking in Emergencies ...4-5 Electronic Stability Control (ESC) ...4-6 Traction Control System (TCS) ...4-8 Limited-Slip Rear Axle ...4-10 Steering ...4-10...
Page 178: Your Driving, The Road, And The Vehicle
Your Driving, the Road, and the Vehicle Driving for Better Fuel Economy Driving habits can affect fuel mileage. Here are some driving tips to get the best fuel economy possible. • Avoid fast starts and accelerate smoothly. • Brake gradually and avoid abrupt stops. •...
Page 179: Drunk Driving
Drunk Driving CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness, and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Do not drink and drive or ride with a driver who has been drinking.
Page 180: Braking
Braking See Brake System Warning Light on page 3-25. Braking action involves perception time and reaction time. Deciding to push the brake pedal is perception time. Actually doing it is reaction time. Average reaction time is about three-fourths of a second.
Page 181: Braking In Emergencies
If there is a problem with ABS, this warning light stays on. See Antilock Brake System (ABS) Warning Light on page 3-26. Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking.
Page 182: Electronic Stability Control (Esc)
Electronic Stability Control (ESC) The vehicle has an Electronic Stability Control (ESC) system which combines antilock brake, traction and stability control systems and helps the driver maintain directional control of the vehicle in most driving conditions. ESC activates when the computer senses a discrepancy between the intended path and the direction the vehicle is actually traveling.
Page 183: Competitive Driving Mode
The ESC/TCS button is located on the instrument panel. To turn the traction control system off or back on, press and release the ESC/TCS button. To disable both traction control and ESC, press and hold the button until TRACTION OFF and ESC OFF messages appear, and the ESC/TCS light comes on.
Page 184: Traction Control System (Tcs)
Traction Control System (TCS) The vehicle has a Traction Control System (TCS) that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that the rear wheels are spinning too much or are beginning to lose traction.
Page 185 To turn the system off or on, press and release the ESC/TCS button located on the instrument panel. The DIC will display the appropriate message the button is pressed. Traction Control Operation Traction control limits wheel spin by reducing engine power to the wheels (engine speed management) and by applying brakes to each individual wheel (brake-traction control) as necessary.
Page 186: Power Steering
Limited-Slip Rear Axle Vehicles with a limited slip rear axle can give more traction on snow, mud, ice, sand or gravel. It works like a standard axle most of the time, but when traction is low, this feature will allow the rear wheel with the most traction to move the vehicle.
Page 187: Off-Road Recovery
An emergency like this requires close attention and a quick decision. If holding the steering wheel at the recommended 9 and 3 o’clock positions, it can be turned a full 180 degrees very quickly without removing either hand. But you have to act fast, steer quickly, and just as quickly straighten the wheel once you have avoided the object.
Page 188: Passing
Passing Passing another vehicle on a two-lane road can be dangerous. To reduce the risk of danger while passing: • Look down the road, to the sides, and to crossroads for situations that might affect a successful pass. If in doubt, wait. •...
Page 189: Driving At Night
Of course, traction is reduced when water, snow, ice, gravel, or other material is on the road. For safety, slow down and adjust your driving to these conditions. It is important to slow down on slippery surfaces because stopping distance will be longer and vehicle control more limited.
Page 190: Driving In Rain And On Wet Roads
No one can see as well at night as in the daytime. But, as we get older, these differences increase. A 50-year-old driver might need at least twice as much light to see the same thing at night as a 20-year-old. Driving in Rain and on Wet Roads Rain and wet roads can reduce vehicle traction and affect your ability to stop and accelerate.
Page 191: Before Leaving On A Long Trip
Other Rainy Weather Tips Besides slowing down, other wet weather driving tips include: • Allow extra following distance. • Pass with caution. • Keep windshield wiping equipment in good shape. • Keep the windshield washer ﬂuid reservoir ﬁlled. • Have good tires with proper tread depth. See Tires on page 5-47.
Page 192: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or through mountains is different than driving on ﬂat or rolling terrain. Tips for driving in these conditions include: • Keep the vehicle serviced and in good shape. • Check all ﬂuid levels and brakes, tires, cooling system, and transmission.
Page 193: Winter Driving
Winter Driving Driving on Snow or Ice Drive carefully when there is snow or ice between the tires and the road, creating less traction or grip. Wet ice can occur at about 32°F (0°C) when freezing rain begins to fall, resulting in even less traction. Avoid driving on wet ice or in freezing rain until roads can be treated with salt or sand.
Page 194 Blizzard Conditions Being stuck in snow can be in a serious situation. Stay with the vehicle unless there is help nearby. If possible, use the Roadside Assistance Program on page 7-6. To get help and keep everyone in the vehicle safe: •...
Page 195: If Your Vehicle Is Stuck In Sand, Mud, Ice, Or Snow
Repeat this until help arrives but only when you feel really uncomfortable from the cold. Moving about to keep warm also helps. If it takes some time for help to arrive, now and then when you run the engine, push the accelerator pedal slightly so the engine runs faster than the idle speed.
Page 196: Rocking Your Vehicle To Get It Out
Rocking Your Vehicle to Get It Out Turn the steering wheel left and right to clear the area around the front wheels. Turn off any traction or stability system. Shift back and forth between R (Reverse) and a forward gear, or with a manual transmission, between 1 (First) or 2 (Second) and R (Reverse), spinning the wheels as little as possible.
Page 197 Tire and Loading Information Label Label Example A vehicle speciﬁc Tire and Loading Information label is attached to the center pillar (B-pillar) of your vehicle. With the driver’s door open, you will ﬁnd the label attached below the door latch. This label shows the number of occupant seating positions (A), and the maximum vehicle capacity weight (B) in kilograms and pounds.
Page 198 The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs and there will be ﬁve 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs (1400 −...
Page 199 Example 2 Item Description Vehicle Capacity Weight for Example 2 = Subtract Occupant Weight @ 150 lbs (68 kg) x 2 = Available Cargo Weight = Total Item 400 lbs (181 kg) 300 lbs (136 kg) 100 lbs (45 kg) Example 3 Description Vehicle Capacity...
Page 200 Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight. Certiﬁcation Label A vehicle speciﬁc Certiﬁcation label is attached to the rear edge of the driver’s door or the vehicle’s center pillar (B-pillar) below the driver’s door latch.
Page 201: Towing
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they will keep going.
Page 202 ✍ NOTES 4-26...
Page 203: Service And Appearance Care
Section 5 Service ...5-3 Accessories and Modiﬁcations ...5-3 California Proposition 65 Warning ...5-4 California Perchlorate Materials Requirements ...5-4 Doing Your Own Service Work ...5-4 Adding Equipment to the Outside of the Vehicle ...5-5 Fuel ...5-5 Gasoline Octane ...5-5 Gasoline Speciﬁcations ...5-5 California Fuel ...5-6 Additives ...5-6 Fuels in Foreign Countries ...5-7...
Page 204 Section 5 Tire Pressure Monitor System ...5-54 Tire Pressure Monitor Operation ...5-56 Tire Inspection and Rotation ...5-60 When It Is Time for New Tires ...5-62 Buying New Tires ...5-63 Different Size Tires and Wheels ...5-65 Uniform Tire Quality Grading ...5-65 Wheel Alignment and Tire Balance ...5-67 Wheel Replacement ...5-67 Tire Chains ...5-70...
Page 205: Service
Service For service and parts needs, visit your dealer/retailer. You will receive genuine GM parts and GM-trained and supported service people. Genuine GM parts have one of these marks: Accessories and Modiﬁcations When non-dealer/non-retailer accessories are added to the vehicle, they can affect vehicle performance and safety, including such things as airbags, braking, stability, ride and handling, emissions systems, aerodynamics, durability, and electronic systems like...
Page 206: California Proposition 65 Warning
California Proposition 65 Warning Most motor vehicles, including this one, contain and/or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Engine exhaust, many parts and systems (including some inside the vehicle), many ﬂuids, and some component wear by-products contain and/or emit these chemicals.
Page 207: Adding Equipment To The Outside Of The Vehicle
This vehicle has an airbag system. Before attempting to do your own service work, see Servicing Your Airbag-Equipped Vehicle on page 1-46. Keep a record with all parts receipts and list the mileage and the date of any service work performed. See Maintenance Record on page 6-16.
Page 208: California Fuel
California Fuel If the vehicle is certiﬁed to meet California Emissions Standards, it is designed to operate on fuels that meet California speciﬁcations. See the underhood emission control label. If this fuel is not available in states adopting California emissions standards, the vehicle will operate satisfactorily on fuels meeting federal speciﬁcations, but emission control system performance might be affected.
Page 209: Fuels In Foreign Countries
Also, your dealer/retailer has additives that will help correct and prevent most deposit-related problems. Gasolines containing oxygenates, such as ethers and ethanol, and reformulated gasolines might be available in your area. We recommend that you use these gasolines, if they comply with the speciﬁcations described earlier. However, E85 (85% ethanol) and other fuels containing more than 10% ethanol must not be used in vehicles that were not designed for those fuels.
Page 210: Filling The Tank
Filling the Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off the engine when you are refueling.
Page 211 CAUTION: Fuel can spray out on you if you open the fuel cap too quickly. If you spill fuel and then something ignites it, you could be badly burned. This spray can happen if the tank is nearly full, and is more likely in hot weather.
Page 212: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in the vehicle. Static electricity discharge from the container can ignite the fuel vapor. You can be badly burned and the vehicle damaged if this occurs.
Page 213: Hood Release
Hood Release To open the hood, do the following: 1. Locate the interior hood release lever. It is located below the instrument panel on the driver’s side of the vehicle. 2. Pull down on the rear edge of the lever to release the hood latch.
Page 214: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 2.4L L4 engine, this is what you will see: 5-12...
Page 215 A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-31. B. Coolant Surge Tank and Pressure Cap. See Cooling System on page 5-23. C. Brake Master Cylinder Reservoir. See “Brake Fluid” under Brakes on page 5-32 and Hydraulic Clutch on page 5-23.
Page 216 When you open the hood on the 2.0L L4 engine, this is what you will see: 5-14...
Page 217: Engine Oil
A. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-31. B. Coolant Surge Tank and Pressure Cap. See Cooling System on page 5-23. C. Brake Master Cylinder Reservoir. See “Brake Fluid” under Brakes on page 5-32 and Hydraulic Clutch on page 5-23.
Page 218: When To Add Engine Oil
When to Add Engine Oil If the oil is below the MIN (minimum) mark, add at least one quart/liter of the recommended oil. This section explains what kind of oil to use. For engine oil crankcase capacity, see Capacities and Speciﬁcations on page 5-104.
Page 219: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use For Vehicles With the 2.0L L4 Engine Look for three things: • GM4718M This vehicle’s engine requires a special oil meeting GM Standard GM4718M, such as Mobil 1 equivalent. Oils meeting this standard may be identiﬁed as synthetic.
Page 220 For Vehicles With the 2.4L L4 Engine Look for three things: • GM6094M Use only an oil that meets GM Standard GM6094M. • SAE 5W-30 SAE 5W-30 is best for the vehicle. These numbers on an oil container show its viscosity, or thickness. Do not use other viscosity oils such as SAE 20W-50.
Page 221: Engine Oil Life System
Cold Temperature Operation For Vehicles With the 2.4L L4 Engine If in an area of extreme cold, where the temperature falls below −20°F (−29°C), use either an SAE 5W-30 synthetic oil or an SAE 0W-30 engine oil. Both provide easier cold starting for the engine at extremely low temperatures.
Page 222: How To Reset The Engine Oil Life System
How to Reset the Engine Oil Life System The Engine Oil Life System calculates when to change your engine oil and ﬁlter based on vehicle use. Whenever the oil is changed, reset the system so it can calculate when the next oil change is required. If a situation occurs where the oil is changed prior to a CHANGE OIL SOON message being turned on, reset the system.
Page 223: Engine Air Cleaner/Filter
Engine Air Cleaner/Filter 2.0L L4 Engine 2.4L L4 Engine See Engine Compartment Overview on page 5-12 for the location of the engine air cleaner/ﬁlter. When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter element at each scheduled Maintenance II service interval and replace the air cleaner/ﬁlter element at the ﬁrst oil change after 50,000 miles (80 000 km).
Page 224: Automatic Transmission Fluid
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/ﬁlter remove the ﬁlter from the vehicle and lightly shake the ﬁlter to release loose dust and dirt. If the ﬁlter remains caked with dirt, a new ﬁlter is required. To inspect or replace the ﬁlter, open the clamps that hold the cover on and lift off the cover.
Page 225: Manual Transmission Fluid
Manual Transmission Fluid It is not necessary to check the manual transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take the vehicle to a dealer/retailer for service. Have it repaired as soon as possible.
Page 226 2.0L L4 Engine A. Coolant Surge Tank and Pressure Cap B. Electric Engine Cooling Fan (Out of View) CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan.
Page 227: Engine Coolant
Engine Coolant The cooling system in the vehicle is ﬁlled with ® DEX-COOL engine coolant. This coolant is designed to remain in the vehicle for ﬁve years or 150,000 miles (240 000 km), whichever occurs ﬁrst. The following explains the cooling system and how to check and add coolant when it is low.
Page 228: Checking Coolant
Checking Coolant The vehicle must be on a level surface when checking the coolant level. The coolant surge tank is located in the engine compartment on the driver’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location.
Page 229 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can cause injury. Keep hands, clothing, and tools away from any underhood electric fan. CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly.
Page 230 3. Fill the coolant surge tank with the proper mixture, to the COLD FILL line. Wait about ﬁve minutes, then check to see if the level is below the COLD FILL line. If the level is below the line, add additional coolant to bring the level up to the line.
Page 231: Engine Overheating
Engine Overheating The vehicle has an indicator to warn of engine overheating. There is an engine coolant temperature warning light on your vehicle’s instrument panel. See Engine Coolant Temperature Warning Light on page 3-28 for more information. You may decide not to lift the hood when this warning appears, but instead get service help right away.
Page 232: Power Steering Fluid
If No Steam Is Coming From The Engine Compartment If an engine overheat warning is displayed but no steam can be seen or heard, the problem may not be too serious. Sometimes the engine can get a little too hot when the vehicle: •...
Page 233: Windshield Washer Fluid
When to Check Power Steering Fluid The power steering ﬂuid does not need to be checked regularly, unless there is a suspected leak or an unusual noise. If there is ﬂuid loss, have the system inspected and repaired. How to Check Power Steering Fluid To check the power steering ﬂuid: 1.
Page 234: Brakes
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. See Engine Compartment Overview on page 5-12 for reservoir location. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water.
Page 235 Do not top off the brake/clutch ﬂuid. Adding ﬂuid does not correct a leak. If ﬂuid is added when the brake linings are worn, there will be too much ﬂuid when new brake linings are installed. Add or remove ﬂuid, as necessary, only when work is done on the brake/clutch hydraulic system.
Page 236: Brake Wear
Brake Wear This vehicle has disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound can come and go or be heard all the time the vehicle is moving, except when applying the brake pedal ﬁrmly.
Page 237: Battery
Battery This vehicle has a maintenance free battery. When it is time for a new battery, see your dealer/retailer for one that has the replacement number shown on the original battery’s label. See Engine Compartment Overview on page 5-12 for battery location. Warning: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause...
Page 238: Jump Starting
Jump Starting If the vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start the vehicle. Be sure to use the following steps to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 239 4. Open the hood on the other vehicle and locate the positive (+) and negative (−) terminal locations on that vehicle. You will not need to access your battery for jump starting. The vehicle has a remote positive (+) and a remote negative (−) jump starting terminal.
Page 240 CAUTION: An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan. CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded.
Page 241 Do not connect positive (+) to negative (−) or you will get a short that would damage the battery and maybe other parts too. And do not connect the negative (−) cable to the negative (−) terminal on the dead battery because this can cause sparks. 6.
Page 242: Rear Axle
Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 243: Headlamp Aiming
How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface. If the level is below the bottom of the ﬁller plug hole, located on the rear axle, you’ll need to add some lubricant. Add enough lubricant to raise the level to the bottom of the ﬁller plug hole.
Page 244: Bulb Replacement
Bulb Replacement For the proper type of replacement bulbs, see Replacement Bulbs on page 5-45. For any bulb changing procedure not listed in this section, contact your dealer/retailer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 245: Front Turn Signal, Parking And Fog Lamps
Front Turn Signal, Parking and Fog Lamps A. Front Turn Signal/ Parking Lamp B. Fog Lamp (If Equipped) To replace one of these bulbs: 1. Open the hood. See Hood Release on page 5-11. 2. Locate the bulb assembly under the front bumper. 3.
Page 246: Taillamps, Turn Signal, And Stoplamps (Removable Hardtop)
4. Turn the bulb socket counterclockwise and pull it straight out of the taillamp assembly. 5. Pull the old bulb straight out of the bulb socket. 6. Push the new bulb straight into the bulb socket until it connects. 7. Push the bulb socket straight into the taillamp assembly and turn it clockwise to lock it into place.
Page 247: License Plate Lamp
License Plate Lamp To replace the license plate lamp bulb: 1. Remove the license plate assembly by turning the two screws counterclockwise. 2. Turn and pull the license plate lamp forward through the fascia opening. 3. Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
Page 248: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected for wear and cracking. See Scheduled Maintenance on page 6-4 for more information. Replacement blades come in different types and are removed in different ways. For proper type and length, see Maintenance Replacement Parts on page 6-14.
Page 249: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your vehicle Warranty booklet for details. For additional information refer to the tire manufacturer. CAUTION: Poorly maintained and improperly used tires are dangerous.
Page 250: Winter Tires
Low-Proﬁle Tires If your vehicle has P245/45R18 size tires, they are classiﬁed as low-proﬁle tires. These tires are designed for very responsive driving on wet or dry pavement. You may also notice more road noise with low-proﬁle performance tires and that they tend to wear faster.
Page 251: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into its sidewall. The example below shows a typical passenger (p-metric) tire sidewall. Passenger (P-Metric) Tire Example (A) Tire Size The tire size is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type, and service description.
Page 252: Tire Terminology And Deﬁnitions
(G) Maximum Cold Inﬂation Load Limit Maximum load that can be carried and the maximum pressure needed to support that load. Tire Size The following illustration shows an example of a typical passenger (p-metric) vehicle tire size. (A) Passenger (P-Metric) Tire version of a metric tire sizing system.
Page 253 Accessory Weight This means the combined weight of optional accessories. Some examples of optional accessories are, automatic transmission, power steering, power brakes, power windows, power seats, and air conditioning. Aspect Ratio The relationship of a tire’s height to its width. Belt A rubber coated layer of cords that is located between the plies and the tread.
Page 254 Maximum Inﬂation Pressure pressure to which a cold tire can be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating The load rating for a tire at the maximum permissible inﬂation pressure for that tire. Maximum Loaded Vehicle Weight curb weight, accessory weight, vehicle capacity weight, and production options weight.
Page 255: Inﬂation - Tire Pressure
UTQGS (Uniform Tire Quality Grading Standards) A tire information system that provides consumers with ratings for a tire’s traction, temperature, and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-65.
Page 256: Tire Pressure Monitor System
are cold. The recommended cold tire inﬂation pressure, shown on the label, is the minimum amount of air pressure needed to support your vehicle’s maximum load carrying capacity. For additional information regarding how much weight your vehicle can carry, and an example of the Tire and Loading Information label, see Loading the Vehicle on page 4-20.
Page 257 As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is signiﬁcantly under-inﬂated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inﬂate them to the proper pressure.
Page 258: Tire Pressure Monitor Operation
The TPMS operates on a radio frequency and complies with RSS-210 of Industry and Science Canada. Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference received, including interference that may cause undesired operation of the device.
Page 259: Tpms Malfunction Light And Message
A Tire and Loading Information label, attached to your vehicle, shows the size of your vehicle’s original equipment tires and the correct inﬂation pressure for your vehicle’s tires when they are cold. See Loading the Vehicle on page 4-20, for an example of the Tire and Loading Information label and its location on your vehicle.
Page 260: Tpms Sensor Matching Process
• Replacement tires or wheels do not match your vehicle’s original equipment tires or wheels. Tires and wheels other than those recommended for your vehicle could prevent the TPMS from functioning properly. See Buying New Tires on page 5-63. • Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.
Page 261 the turn signals ﬂash one time to conﬁrm the sensor identiﬁcation code has been matched to the tire/wheel position. 6. The passenger side front turn signal comes on to indicate that corner sensor is ready to be learned. Proceed to the passenger side front tire and repeat the procedure in Step 5.
Page 262: Tire Inspection And Rotation
6. Remove the valve cap from the tire’s valve stem. Activate the TPMS sensor by increasing or decreasing the tire’s air pressure for about eight seconds. The horn chirp, can take up to 30 seconds to sound. It chirps one time and then all the turn signals ﬂash one time to conﬁrm the sensor identiﬁcation code has been matched to the tire/wheel position.
Page 263 Any time you notice unusual wear, rotate the tires as soon as possible and check wheel alignment. Also check for damaged tires or wheels. See When It Is Time for New Tires on page 5-62 and Wheel Replacement on page 5-67. Non-Directional Tires When rotating Goodyear Eagle RSA P245/45R18 non-directional tires, always use the correct...
Page 264: When It Is Time For New Tires
After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-53 and Loading the Vehicle on page 4-20. Reset the Tire Pressure monitor System. See Tire Pressure Monitor Operation on page 5-56.
Page 265: Buying New Tires
You need new tires if any of the following statements are true: • You can see the indicators at three or more places around the tire. • You can see cord or fabric showing through the tire’s rubber. • The tread or sidewall is cracked, cut, or snagged deep enough to show cord or fabric.
Page 266 GM recommends replacing tires in sets of four. This is because uniform tread depth on all tires will help keep your vehicle performing most like it did when the tires were new. Replacing less than a full set of tires can affect the braking and handling performance of your vehicle.
Page 267: Different Size Tires And Wheels
Different Size Tires and Wheels If you add wheels or tires that are a different size than your original equipment wheels and tires, this may affect the way your vehicle performs, including its braking, ride and handling characteristics, stability, and resistance to rollover.
Page 268 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speciﬁed government test course. For example, a tire graded 150 would wear one and a half (1.5) times as well on the government course as a tire graded 100.
Page 269: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 270 If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. CAUTION: Using the wrong replacement wheels, wheel bolts, or wheel nuts on your vehicle can be dangerous.
Page 271: Used Replacement Wheels
CAUTION: Never use oil or grease on studs or the threads of the wheel nuts. If you do, the wheel nuts might come loose and the wheel could fall off, causing a crash. CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off.
Page 272: Tire Chains
Tire Chains CAUTION: Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause you to lose control of the vehicle and you or others may be injured in a crash.
Page 273: Tire Sealant And Compressor Kit (Without Selector Switch)
If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place and stopping. Then do this: 1. Turn on the hazard warning ﬂashers. See Hazard Warning Flashers on page 3-5. 2. Park your vehicle. If your vehicle has an automatic transmission, set the parking brake ﬁrmly and put the shift lever in P (Park).
Page 274 If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under “Tire Sealant and Compressor Kit (With Selector Switch).” 5-72 CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 275 CAUTION: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.
Page 276 Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer.
Page 277 Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-70. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-89.
Page 278 9. Inﬂate the tire to the recommended inﬂation pressure using the pressure gage (E). The recommended inﬂation pressure can be found on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-53. The pressure gage (E) may read higher than the actual tire pressure while the compressor is on.
Page 279 18. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured).” If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inﬂation pressure, stop driving the vehicle.
Page 280 2. Unlock the air only hose (F) from the sealant canister (B) by pulling up on the lever. 3. Pull the air only hose (F) from the sealant canister (B). 4. Remove the power plug (C) from the air compressor (A). 5.
Page 281 Removal and Installation of the Sealant Canister To remove the sealant canister: 1. Unlock the air only hose (F) from the sealant canister (B) by pulling up on the lever. 2. Pull the air only hose (F) from the sealant canister (B).
Page 282: Tire Sealant And Compressor Kit (With Selector Switch)
To install a new sealant canister: 1. Align the sealant/air hose (F) with the slot in the air compressor. 2. Push the sealant canister (B) down and turn it clockwise. 3. Wrap the sealant/air hose (F) around the air compressor channel to stow it in its original location. 4.
Page 283 If the vehicle has the tire sealant and compressor kit shown above, follow the operating instructions under “Tire Sealant and Compressor Kit (Without Selector Switch).” CAUTION: Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle.
Page 284 CAUTION: Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.
Page 285 Tire Sealant Read and follow the safe handling instructions on the label adhered to the sealant canister. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer/retailer.
Page 286 Always do a safety check ﬁrst. See If a Tire Goes Flat on page 5-70. Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and compressor kit from its storage location. See Tire Sealant and Compressor Kit Storage on page 5-89.
Page 287 10. Inﬂate the tire to the recommended inﬂation pressure using the pressure gage (C). The recommended inﬂation pressure can be found on the Tire and Loading Information label. See Inﬂation - Tire Pressure on page 5-53. The pressure gage (C) may read higher than the actual tire pressure while the compressor is on.
Page 288 19. Stop at a safe location and check the tire pressure. Refer to Steps 1 through 11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inﬂate a Tire (Not Punctured).” If the tire pressure has fallen more than 10 psi (68 kPa) below the recommended inﬂation pressure, stop driving the vehicle.
Page 289 2. Unwrap the air only hose (G) and the power plug (H). 3. Place the kit on the ground. 4. Remove the tire valve stem cap from the ﬂat tire by turning it counterclockwise. 5. Attach the air only hose (G) onto the tire valve stem by turning it clockwise until it is tight.
Page 290 15. Place the equipment in the original storage location in the vehicle. The tire sealant and compressor kit has an accessory adapter located in a compartment on the bottom of its housing that may be used to inﬂate air mattresses, balls, etc.
Page 291: Tire Sealant And Compressor Kit Storage
Tire Sealant and Compressor Kit Storage Convertible The tire sealant and compressor kit is located in the driver side rear corner of the trunk. 1. Make sure the convertible top is in the up position before accessing the tire sealant and compressor kit.
Page 292: Appearance Care
Coupe 1. Open the trunk. See Trunk on page 2-8. 2. Remove the rear storage compartment cover by pulling up on the handle. 3. Squeeze the two tabs of the quick release buckle to remove the tire sealant and compressor kit. 4.
Page 293: Fabric/Carpet
Notice: Using abrasive cleaners when cleaning glass surfaces on the vehicle, could scratch the glass and/or cause damage to the rear window defogger. When cleaning the glass on the vehicle, use only a soft cloth and glass cleaner. Many cleaners contain solvents that may become concentrated in the vehicle’s breathing space.
Page 294: Leather
To clean: 1. Saturate a lint-free, clean white cloth with water or club soda. 2. Wring the cloth to remove excess moisture. 3. Start on the outside edge of the soil and gently rub toward the center. Continue cleaning, using a clean area of the cloth each time it becomes soiled.
Page 295: Care Of Safety Belts
or wax-based products, or those containing organic solvents to clean the vehicle’s interior because they can alter the appearance by increasing the gloss in a non-uniform manner. Some commercial products may increase gloss on the instrument panel. The increase in gloss may cause annoying reﬂections in the windshield and even make it difficult to see through the windshield under certain conditions.
Page 296: Cleaning Exterior Lamps/Lenses
Rinse the vehicle well, before washing and after to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the ﬁnish with a soft, clean chamois or an all-cotton towel to avoid surface scratches and water spotting. High pressure car washes may cause water to enter the vehicle.
Page 297: Windshield And Wiper Blades
Use special care with aluminum trim. To avoid damaging protective trim, never use auto or chrome polish, steam or caustic soap to clean aluminum. A coating of wax, rubbed to high polish, is recommended for all bright metal parts. Windshield and Wiper Blades Clean the outside of the windshield with glass cleaner.
Page 298: Aluminum Or Chrome-Plated Wheels And Trim
Aluminum or Chrome-Plated Wheels and Trim The vehicle may have either aluminum or chrome-plated wheels. Keep the wheels clean using a soft clean cloth with mild soap and water. Rinse with clean water. After rinsing thoroughly, dry with a soft clean towel. A wax may then be applied.
Page 299: Sheet Metal Damage
Sheet Metal Damage If the vehicle is damaged and requires sheet metal repair or replacement, make sure the body repair shop applies anti-corrosion material to parts repaired or replaced to restore corrosion protection. Original manufacturer replacement parts will provide the corrosion protection while maintaining the vehicle warranty.
Page 300: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver side. It can be seen through the windshield from outside the vehicle. The VIN also appears on the Vehicle Certiﬁcation and Service Parts labels and the certiﬁcates of title and registration.
Page 301: Headlamp Wiring
The vehicle has an airbag system. Before attempting to add anything electrical to the vehicle, see Servicing Your Airbag-Equipped Vehicle on page 1-46. Headlamp Wiring The headlamp wiring is protected by fuses in the fuse block. An electrical overload will cause the lamps to turn off.
Page 302 Fuses Fuse Puller Empty Empty Empty Empty Ampliﬁer Cluster 5-100 Usage Fuses Usage Ignition Switch, PassKey III+ Stoplamp Climate Control System, PassKey III+ Empty Spare Airbag Spare Wiper Climate Control System, Automatic Occupant Sensing Module, Crank Relay, Instrument Panel Cluster Empty Empty Steering Wheel Controls...
Page 303: Underhood Fuse Block
Fuses Steering Wheel Control Backlighting Power Windows Climate Control System Empty Retained Accessory Power Underhood Fuse Block The underhood fuse block is located in the engine compartment on the passenger side of the vehicle. Lift the cover for access to the fuse block. Notice: Spilling liquid on any electrical components on the vehicle may damage it.
Page 304 Fuses Trunk Empty Fuel Pump Rear Defogger Relay Air Conditioning Clutch Relay Empty Empty Trunk Release Relay Fuel Pump Relay Empty Mirrors Air Conditioning Empty Cooling Fan 2 Relay (LE5); Empty (LNF) Fuse Puller Powertrain Relay Empty Back-up Lamps Relay (Automatic Transmission);...
Page 305 Fuses Usage Daytime Running Lamps Relay Daytime Running Lamps Cooling Fan 1 Relay (LE5); Empty (LNF) Run/Crank Relay Windshield Wiper Low/High Relay Fog Lamps Fog Lamps Relay Horn Relay ® S Band, OnStar , Remote Keyless Entry System Antilock Brake System Wiper Diode Windshield Wiper Horn...
Page 306: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Please refer to Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant R134a Cooling System 2.0L L4 Engine — Automatic 2.0L L4 Engine — Manual 2.4L L4 Engine —...
Page 307 Engine 2.0L L4 2.4L L4 Engine Speciﬁcations VIN Code Transmission Automatic Manual Automatic Manual Spark Plug Gap 0.035 in (0.90 mm) 0.040 in (1.01 mm) 5-105...
Page 308 ✍ NOTES 5-106...
Page 309 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using the Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 310: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements the vehicle warranties. See the Warranty and Owner Assistance booklet or your dealer/retailer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts, and recommended ﬂuids and...
Page 311: Using The Maintenance Schedule
Using the Maintenance Schedule We want to help keep this vehicle in good working condition. But we do not know exactly how you will drive it. You might drive very short distances only a few times a week. Or you might drive long distances all the time in very hot, dusty weather.
Page 312: Scheduled Maintenance
The proper replacement parts, ﬂuids, and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-12 and Maintenance Replacement Parts on page 6-14. When the vehicle is serviced, make sure these are used. All parts should be replaced and all necessary repairs done before you or anyone else drives the vehicle.
Page 313 Change engine oil and ﬁlter. See Engine Oil on page 5-15. Reset oil life system. See Engine Oil Life System on page 5-19. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-21.
Page 314: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service and Miles (Kilometers) Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 315: Maintenance Footnotes
Maintenance Footnotes (a) Visually inspect brake lines and hoses for proper hook-up, binding, leaks, cracks, chaﬁng, etc. Inspect disc brake pads for wear and rotors for surface condition. Inspect drum brake linings/shoes for wear or cracks. Inspect other brake parts, including drums, wheel cylinders, calipers, parking brake, etc.
Page 316: Owner Checks And Services
(j) A ﬂuid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the ﬂuid level checked. Add ﬂuid if needed. (k) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: −...
Page 317: At Least Once A Month
At Least Once a Month Tire Inspection and Inﬂation Check Inspect the vehicle’s tires for wear and make sure they are inﬂated to the correct pressures. See Inﬂation - Tire Pressure on page 5-53. At Least Once a Year Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly.
Page 318: Ignition Transmission Lock Check
Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before starting this check, be sure there is enough room around the vehicle. It should be parked on a level surface.
Page 319: Underbody Flushing Service
Parking Brake and Automatic Transmission P (Park) Mechanism Check CAUTION: When you are doing this check, the vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of the vehicle in case it begins to roll. Be ready to apply the regular brake at once should the vehicle begin to move.
Page 320: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Engine Oil Certiﬁed for Gasoline Engines (2.4L L4 starburst symbol.
Page 321 Usage Fluid/Lubricant SAE 75W-90 Synthetic Axle Lubricant (GM Part Rear Axle No. U.S. 89021677, in Canada 89021678) meeting GM Speciﬁcation 9986115. SAE 75W-90 Synthetic Axle Lubricant (GM Part No. U.S. 89021677, in Canada 89021678) meeting GM Rear Axle Speciﬁcation 9986115. With a (Limited-Slip complete drain and reﬁll add Differential)
Page 322: Maintenance Replacement Parts
Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer/retailer. Part Engine Air Cleaner/Filter 2.0L L4 Engine 2.4L L4 Engine Engine Oil Filter Spark Plugs 2.0L L4 Engine 2.4L L4 Engine Wiper Blades Driver Side —...
Page 323: Engine Drive Belt Routing
Engine Drive Belt Routing Belt routing for air conditioning (AC) shown. Dotted line represents routing for vehicles without AC. 6-15...
Page 324: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service, and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. You should retain all maintenance receipts.
Page 325 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-17...
Page 326 Maintenance Record (cont’d) Odometer Maintenance I or Date Serviced By Services Performed Reading Maintenance II 6-18...
Page 327: Customer Assistance Information
Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-5 Customer Assistance Offices ...7-5 GM Mobility Reimbursement Program ...7-6 Roadside Assistance Program ...7-6 Scheduling Service Appointments ...7-8 Courtesy Transportation ...7-9 Collision Damage Repair ...7-10 Customer Assistance Information...
Page 328: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Pontiac. Normally, any concerns with the sales transaction or the operation of the vehicle will be resolved by the dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 329 charge and your case will generally be heard within 40 days. If you do not agree with the decision given in your case, you may reject it and proceed with any other venue for relief available to you. You can contact the BBB Auto Line Program using the toll-free telephone number or write them at the following address: BBB Auto Line Program...
Page 330: Online Owner Center
— all in one convenient place. • Digital owner manual, warranty information, and more • Online service and maintenance records • Find Pontiac dealers for service nationwide • Exclusive privileges and offers • Recall notices for your speciﬁc vehicle • ®...
Page 331: Customer Assistance For Text Telephone (Tty) Users
Canada can dial 1-800-263-3830.) Customer Assistance Offices Pontiac encourages customers to call the toll-free number for assistance. However, if a customer wishes to write or e-mail Pontiac, the letter should be addressed to: United States — Customer Assistance Pontiac Customer Assistance Center P.O.
Page 332: Gm Mobility Reimbursement Program
Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) — Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma #2740 Col. Lomas de Bezares C.P. 11910, Mexico, D.F. 01-800-508-0000 Long Distance: 011-52-53 29 0 800 GM Mobility Reimbursement...
Page 333 Roadside Assistance program at any time without notiﬁcation. Pontiac and General Motors of Canada Limited reserve the right to limit services or payment to an owner or driver if they decide the claims are made too often, or the same type of claim is made many times.
Page 334: Scheduling Service Appointments
Services Not Included in Roadside Assistance • Impound towing caused by violation of any laws. • Legal ﬁnes. • Mounting, dismounting or changing of snow tires, chains, or other traction devices. • Towing or services for vehicles driven on a non-public road or highway.
Page 335: Courtesy Transportation
If your vehicle cannot be scheduled into the service department immediately, keep driving it until it can be scheduled for service, unless, of course, the problem is safety-related. If it is, please call your dealership/retailer, let them know this, and ask for instructions. If the dealer/retailer requests you to bring the vehicle for service, you are urged to do so as early in the work day as possible to allow for the same day repair.
Page 336: Collision Damage Repair
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle that you obtain if your vehicle is kept for an overnight warranty repair. Rental reimbursement will be limited and must be supported by original receipts.
Page 337: If A Crash Occurs
Aftermarket collision parts are also available. These are made by companies other than GM and may not have been tested for your vehicle. As a result, these parts may ﬁt poorly, exhibit premature durability/ corrosion problems, and may not perform properly in subsequent collisions.
Page 338 • If you need roadside assistance, call GM Roadside Assistance. See Roadside Assistance Program on page 7-6 for more information. • If your vehicle cannot be driven, know where the towing service will be taking it. Get a card from the tow truck operator or write down the driver’s name, the service’s name, and the phone number.
Page 339: Reporting Safety Defects
Remember if your vehicle is leased you may be obligated to have the vehicle repaired with Genuine GM parts, even if your insurance coverage does not pay the full cost. If another party’s insurance company is paying for the repairs, you are not obligated to accept a repair valuation based on that insurance company’s collision policy repair limits, as you have no contractual limits with that company.
Page 340: Reporting Safety Defects To General Motors
General Motors In addition to notifying NHTSA (or Transport Canada) in a situation like this, please notify General Motors. Call 1-800-762-2737, or write: Pontiac Customer Assistance Center P.O. Box 33172 Detroit, MI 48232-5172 In Canada, call 1-800-263-3777 (English) or 1-800-263-7854 (French), or write:...
Page 341: Vehicle Data Recording And Privacy
ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc. on the World Wide Web at: helminc.com Or you can write to: Helm, Incorporated P.O. Box 07130 Detroit, MI 48207 Prices are subject to change without notice and without incurring obligation.
Page 342: Onstar
This data can help provide a better understanding of the circumstances in which crashes and injuries occur. Important: EDR data is recorded by your vehicle only if a non-trivial crash situation occurs; no data is recorded by the EDR under normal driving conditions and no personal data (e.g., name, gender, age, and crash location) is recorded.
Page 343 Accessories and Modiﬁcations ... 5-3 Accessory Power Outlets ... 3-14 Adding Equipment to Your Airbag-Equipped Vehicle ... 1-47 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-98 Air Cleaner/Filter, Engine ... 5-21 Air Conditioning ... 3-16 Airbag Passenger Status Indicator ... 3-24 Readiness Light ...
Page 344 Audio System(s) ... 3-49 Automatic Door Lock ... 2-7 Automatic Door Unlock ... 2-7 Automatic Transmission Fluid ... 5-22 Operation ... 2-19 Battery ... 5-35 Run-Down Protection ... 3-14 ® Bluetooth ... 3-68 Brake Emergencies ... 4-5 Brake Fluid ... 5-32 Brakes ...
Page 345 Child Restraints Child Restraint Systems ... 1-29 Infants and Young Children ... 1-25 Lower Anchors and Tethers for Children ... 1-31 Older Children ... 1-22 Securing a Child Restraint in the Right Front Seat Position ... 1-32 Chime Level Adjustment ... 3-81 Cigarette Lighter ...
Page 346 Daytime Running Lamp ... 3-13 Defensive Driving ... 4-2 Delayed Locking ... 2-7 Disc, MP3 ... 3-60 Doing Your Own Service Work ... 5-4 Door Automatic Door Lock ... 2-7 Automatic Door Unlock ... 2-7 Delayed Locking ... 2-7 Manual Door Locks ... 2-6 Power Door Locks ...
Page 347 Entry/Exit Lighting ... 3-14 Event Data Recorders ... 7-15 Extender, Safety Belt ... 1-21 Filter Engine Air Cleaner ... 5-21 Finish Damage ... 5-97 Fixed Mast Antenna ... 3-81 Flashers, Hazard Warning ... 3-5 Flash-to-Pass ... 3-7 Flat Tire ... 5-70 Fluid Automatic Transmission ...
Page 348 Headlamps ... 3-12, 5-42 Bulb Replacement ... 5-42 Daytime Running Lamp ... 3-13 Flash-to-Pass ... 3-7 Front Turn Signal, Parking and Fog Lamps ... 5-43 Halogen Bulbs ... 5-42 High/Low Beam Changer ... 3-7 On Reminder ... 3-13 Heater ... 3-16 Height Adjuster, Driver Seat ...
Page 349 Light Airbag Readiness ... 3-23 Antilock Brake System (ABS) Warning ... 3-26 Brake System Warning ... 3-25 Charging System ... 3-25 Engine Coolant Temperature Warning ... 3-28 Highbeam On ... 3-33 Low Coolant Warning ... 3-28 Low Fuel Warning ... 3-34 Oil Pressure ...
Page 350 Message DIC Warnings and Messages ... 3-37 Mirror Reading Lamps ... 3-14 Mirrors Manual Rearview Mirror ... 2-29 Outside Manual Mirrors ... 2-29 Outside Power Mirrors ... 2-29 MP3 ... 3-60 MyGMLink.com ... 7-4 Navigation System, Privacy ... 7-16 New Vehicle Break-In ... 2-16 Odometer ...
Page 351 Power Door Locks ... 2-6 Electrical System ... 5-99 Retained Accessory ... 2-17 Steering Fluid ... 5-30 Windows ... 2-11 Privacy ... 7-15 Event Data Recorders ... 7-15 Navigation System ... 7-16 OnStar ... 7-16 Radio Frequency Identiﬁcation ... 7-16 Radio Frequency Identiﬁcation (RFID), Privacy ...
Page 352 Safety Belts (cont.) Safety Belt Extender ... 1-21 Safety Belt Use During Pregnancy ... 1-21 Safety Belts Are for Everyone ... 1-6 Safety Warnings and Symbols ... iii Scheduled Maintenance ... 6-4 Seatback Latches ... 1-5 Seats Driver Seat Height Adjuster ... 1-2 Reclining Seatbacks ...
Page 353 Tire Pressure Light ... 3-29 Tire Sealant Storing ... 5-89 Tires ... 5-47 Aluminum or Chrome-Plated Wheels, Cleaning ... 5-96 Buying New Tires ... 5-63 Chains ... 5-70 Cleaning ... 5-96 Different Size ... 5-65 If a Tire Goes Flat ... 5-70 Inﬂation - Tire Pressure ...
Page 354 Vehicle Identiﬁcation Number (VIN) ... 5-98 Service Parts Identiﬁcation Label ... 5-98 Vehicle Personalization DIC ... 3-41 Ventilation Adjustment ... 3-19 Visors ... 2-12 Warning Lights, Gages, and Indicators ... 3-19 Warnings DIC Warnings and Messages ... 3-37 Hazard Warning Flashers ... 3-5 Safety and Symbols ...

Pontiac 2009 Solstice Owner's Manual

Section 1 Seats and Restraint System

Seats and Restraint System

Front Seats

Safety Belts

Child Restraints

Airbag System

Restraint System Check

Section 2 Features and Controls

Features and Controls

Keys

Doors and Locks

Windows

Theft-Deterrent Systems

Starting and Operating Your Vehicle

Mirrors

Onstar System

Storage Areas

Roof Panel

Convertible Top

Section 3 Instrument Panel

Instrument Panel Overview

Climate Controls

Warning Lights, Gages, and Indicators

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and the Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Rear Axle

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Electrical System

Vehicle Identiﬁcation

Capacities and Speciﬁcations

Quick Links

Chapters

Related Manuals for Pontiac 2009 Solstice

Summary of Contents for Pontiac 2009 Solstice