Page 1: Table Of Contents
Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo with CD Climate Controls Manual heating and air conditioning Lights Headlamps Turn signal control Bulb replacement Driver Controls Windshield wiper/washer control Steering wheel adjustment Power windows Speed control Locks and Security Keys Locks...
Page 3: Introduction
The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving For more information on Mazda Motor Corporation and its products visit the following website: In the United States: www.mazdausa.com In Canada: www.mazda.ca...
Page 4 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
Page 5 SPECIAL NOTICES Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. WARNING: By operating other electronic equipment (e.g. mobile telephone without exterior aerial) electromagnetic fields can occur which can cause malfunctions of the vehicle electronics. Therefore you should observe the instructions of the equipment manufacturers.
Page 6 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert Protecting the Environment Air Bag-Front Child Seat Child Seat Tether Anchorage Anti-Lock Brake System Traction Control Hazard Warning Flasher Fuse Compartment Windshield Wash/Wipe Rear Window Defrost/Demist See Owner’s Guide...
Page 7 Passenger Compartment Air Filter Check fuel cap INFORMATION ABOUT THIS GUIDE The information found in this guide was accurate at the time of printing. Mazda may change the contents without notice. Introduction Child Safety Door Lock/Unlock Engine Oil Engine Coolant...
Page 8 Instrument Cluster Windshield wiper/washer Headlamp and turn control signal control (pg. 62) (pg. 54) Fog lamp control* Instrument cluster (pg. 55) (pg. 10) Power mirror control* (pg. 68) Speed controls* (pg. 69) Manual tilt steering Driver air bag wheel lever (pg.
Page 9 Instrument Cluster Hazard flasher control (pg. 167) Audio system Rear window defroster (pg. 19) control (pg. 53) 4WD control* (pg. 148) Climate controls (pg. 50) Auxiliary power point (pg. 66) *if equipped...
Page 10: Instrument Cluster
Instrument Cluster WARNING LIGHTS AND CHIMES CHECK FUEL Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 11 What you should do if the Light turns on (without blinking): This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2.
Page 12 Instrument Cluster Low fuel Illuminates when the fuel level in the fuel tank is at, or near, empty (refer to Fuel gauge in this chapter for more information). Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced...
Page 13 Anti-lock brake system (ABS) (if equipped) Illuminates to ensure the circuit is functional. WARNING: If the light remains on, continues to flash or fails to illuminate, have the system serviced immediately. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the brake warning light also remains illuminated with the parking brake released.
Page 14 Instrument Cluster Engine oil pressure Illuminates when the oil pressure falls below the normal range. Check the oil level and add oil if needed. Refer to Engine oil in the Maintenance and specifications chapter. To avoid engine damage, stop the vehicle as soon as safely possible and switch off the engine immediately.
Page 15 Instrument Cluster Check fuel cap (if equipped) Momentarily illuminates when the CHECK ignition is turned to the ON position FUEL to ensure your bulb is working. When this light turns on, check the fuel filler cap. Continuing to operate the vehicle with the check fuel cap light on, can activate the warning light.
Page 16: Gauges
Instrument Cluster GAUGES CHECK FUEL Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Page 17 Instrument Cluster Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine. Speedometer Indicates the current vehicle speed. Fuel gauge Displays approximately how much fuel is in the fuel tank. The fuel gauge may vary slightly when the vehicle is in motion or on a grade.
Page 18 Instrument Cluster Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. Press and hold the button for 1 or more seconds to reset. Press and release the button in less than 1 second to toggle between odometer and trip odometer.
Page 19: Entertainment Systems
Entertainment Systems AM/FM RADIO WITH COMPACT DISC PLAYER Volume/power control Ensure that the ignition is either in the ACC or ON position for the audio system to function. Press the control to turn the audio system on or off.
Page 20 Entertainment Systems Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE:Once the system is turned off, press the VOL control again to listen to the frequency last tuned to.
Page 21 Entertainment Systems Press the TUNE control to select the desired function. Turn the TUNE control to adjust the desired levels. Refer to Treble adjust for specific instructions on level adjustments. The TUNE control will also work in radio mode to manually increase or decrease the frequency.
Page 22 Entertainment Systems Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disable scan mode.
Page 23 Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the audio control until TREB is displayed. Turn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 24 Entertainment Systems Turn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers.
Page 25 Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Your vehicle may be equipped with a mid-range adjust.
Page 26 Entertainment Systems Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display. Release the TUNE control when the desired level is reached. NOTE: Approximately 5 seconds after selecting any mode, the volume function will be automatically selected.
Page 27 Auto memory tuning Auto memory tuning allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Page 28 Entertainment Systems The cassette’s top side is playing when The cassette’s bottom side is playing when display. NOTE: When a metal tape is inserted, the player will automatically compensate and MTL will appear in the display. Press the VOL (Volume) control to stop cassette play.
Page 29 Repeat play in CD mode Press the RPT control during play. RPT will illuminate in the display. The current selection will be repeated. To disengage repeat play, press the RPT control again. Track search Track search works in CD mode. Press the on the TRACK control to skip forward to the beginning of...
Page 30 Entertainment Systems NOTE: When a CD is ejected during play, the next CD will be played automatically. Random play The random play feature works in CD mode and plays the selections on the current CD in random order. Random play in CD mode Press the RDM control during play.
Page 31 Entertainment Systems a second time, the minutes will be set to 00. If the clock’s current time setting is within the latter part of the hour (from 30 to 59 min), the hour setting will automatically advance one hour. Changing the display mode The display can be changed to alternate between the clock and the audio.
Page 32 Entertainment Systems Press the control to turn the audio system on or off. Turn the control to raise or lower the volume. NOTE: To prevent the battery from being discharged, do not leave the audio system on for a long period when the engine is not running. NOTE:Once the system is turned off, press the VOL control again to listen to the frequency last tuned to.
Page 33 Entertainment Systems Tune audio control The TUNE control is a multi-functional control which works in radio, tape and CD modes to adjust the levels of bass, treble, balance, fade and mid-range. Press the TUNE control to select the desired function. Turn the TUNE control to adjust the desired levels.
Page 34 Entertainment Systems Scan function The scan function works in radio and CD mode. Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to disable scan mode.
Page 35 Entertainment Systems Treble adjust The treble adjust control allows you to increase or decrease the audio system’s treble output. Press the audio control until TREB is displayed. Turn the control to increase (right) or decrease (left) the amount of treble output. Bass adjust The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 36 Entertainment Systems Turn the control to increase (right) or decrease (left) the amount of bass output. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the audio control until FADE appears. Turn the control (right or left) to adjust between the front and rear speakers.
Page 37 Entertainment Systems Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the audio control until BAL appears. Turn the control (right or left) to adjust between the right and left speakers. Mid-range adjust (if equipped) Your vehicle may be equipped with a mid-range adjust.
Page 38 Entertainment Systems Turn the control to the right to increase the mid-range. Turn the control to the left to decrease the mid-range. The level will display. Release the TUNE control when the desired level is reached. NOTE: Approximately 5 seconds after selecting any mode, the volume function will be automatically selected.
Page 39 Auto memory tuning Auto memory tuning allows you to set strong radio stations without losing your original manually set preset stations. This feature is helpful on trips when you travel between cities with different radio stations. Starting autoset memory preset 1.
Page 40 Entertainment Systems The cassette’s top side is playing when The cassette’s bottom side is playing when display. NOTE: When a metal tape is inserted, the player will automatically compensate and MTL will appear in the display. Press the VOL (Volume) control to stop cassette play.
Page 41 Repeat play in tape mode Press the RPT control during play. RPT will illuminate in the display. The current selection will be repeated. To disengage repeat play, press the RPT control again. NOTE: RPT may not operate properly if: A tape was recorded at a low level. A tape has long, silent intervals.
Page 42 Entertainment Systems Press the DISC up control to skip forward to the beginning of the next Press the DISC down control to skip back to the beginning of the previous CD. Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback.
Page 43 NOTE: APC may not operate properly if: A tape was recorded at a low level. A tape has long, silent intervals. A tape is a live recording. A tape has very short intervals of less than 3 seconds. CD loading The load feature allows you to load up to six single CDs into the audio system.
Page 44 Entertainment Systems Eject feature The eject feature works in both tape and CD mode. Ejecting a tape Press the control to stop and eject a tape. NOTE: The cassette tape can be ejected when the ignition switch is in the OFF position. Ejecting a CD 1.
Page 45 Cds can be ejected when the ignition switch is OFF. Press and hold the CD eject control for approximately 2 seconds and all CDs will eject. Random play The random play feature works in CD mode and plays the selections on the current CD in random order.
Page 46 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 47 CD TIPS- CONDENSATION PHENOMENON Immediately after turning on the heater when the vehicle is cold, the CD or optical components (prism and lens) in the CD player/changer may become clouded with condensation. When this happens, the CD will eject immediately when placed in the unit. A clouded CD can be corrected simply by wiping it with a soft cloth.
Page 48 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Mazda CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 49 Radio reception factors Three factors can affect radio reception: Distance/strength. The further an FM signal travels, the weaker it is. The listenable range of the average FM station is approximately 40 km (24 miles). This range can be affected by “signal modulation.” Signal modulation is a process radio stations use to increase their strength/volume relative to other stations.
Page 50: Climate Controls
Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM Fan speed control Controls the volume of air circulated in the vehicle. Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle.
Page 51 NOTE:In snowy or dirty conditions, leave the mode selector in the OFF position. MAX A/C- Uses recirculated air to cool the vehicle. MAX A/C is noisier than A/C but more economical and will cool the inside of the vehicle faster. Airflow will be from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle.
Page 52 Climate Controls (Defrost)-Distributes outside air through the windshield defroster ducts. It can be used to clear ice or fog from the windshield. If the temperature is about 6°C (43°F) or higher, the air conditioner will automatically dehumidify the air to reduce fogging. Operating tips In humid weather conditions, place the climate control system in Defrost mode before driving.
Page 53 To aid in side window defogging/demisting in cold weather conditions: 1. Select the position that distributes air through the Panel and Floor. 2. Set the temperature control to full heat. 3. Set the fan speed to full fan. 4. Direct the outer panel vents towards the side windows. 5.
Page 54: Lights
Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: the ignition must be in the ON position and the headlamp control is in the OFF or Parking lamps position.
Page 55 Flash to pass Pull toward you slightly to activate and release to deactivate. FOG LAMP CONTROL (IF EQUIPPED) The fog lamps can only be turned on when the headlamp control is in the low beams position. Press the foglamp control to activate the fog lamps.
Page 56: Turn Signal Control
The headlamps on your vehicle are properly aimed at the assembly plant. If your vehicle has been in an accident the alignment of your headlamps should be checked by your authorized Mazda dealer. TURN SIGNAL CONTROL Push down to activate the left turn signal.
Page 57: Bulb Replacement
The dome lamp will stay on if the control is moved to the passenger side position. When the control is in the middle position, the lamp will only come on when a door is opened. If the control is moved to the driver’s side position, the lamp will not come on at all.
Page 58 Check the operation of the following interior bulbs frequently: interior overhead lamp map lamp For bulb replacement, see an authorized Mazda dealer. Using the right bulbs Replacement bulbs are specified in the chart below. Headlamp bulbs must be marked with an authorized “D.O.T.” for North America to assure lamp performance, light brightness and pattern and safe visibility.
Page 59 Function Number of bulbs Front door courtesy lamp Map lamps Ashtray lamp All replacement bulbs are clear in color except where noted. To replace all instrument panel lights - see your dealer. Replacing headlamp bulbs 1. Make sure that the headlamp control is in the OFF position. 2.
Page 60 Lights Replacing brake/tail/turn/backup lamps bulbs The brake/tail/turn/backup lamp bulbs are located in the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies. 2. Remove the two screws from the lamp assembly.
Page 61 4. Install the bulb socket in lamp assembly turning it clockwise, 5. Install the lamp assembly on liftgate with two screws. Replacing front parking lamp/turn signal bulbs For bulb replacement, see an authorized Mazda dealer. Replacing high-mount brake lamp bulbs For bulb replacement, see an authorized Mazda dealer.
Page 62: Driver Controls
Driver Controls WINDSHIELD WIPER AND WASHER For intermittent operation, move control down one position. Adjust the rotary control to the desired speed setting. For normal or low speed wiper operation, move control down two positions from OFF. For high speed wiper operation, move control down three positions from OFF.
Page 63 Driver Controls To activate the windshield washer, pull control toward you. Release control to stop washer fluid spray. MIST FUNCTION Move control up and release for one wipe. Windshield wiper blades Check the wiper blades for wear at least twice a year or when they seem less effective.
Page 64 Driver Controls Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to...
Page 65: Steering Wheel Adjustment
Rear window wiper blade Refer to Windshield wiper blades in this section for more information on rear wiper blades. MANUAL TILT STEERING COLUMN Push the tilt steering wheel lever downward to move the steering wheel up or down. Pull the control up into the original position to lock the steering wheel in position.
Page 66 Driver Controls Storage compartment (if equipped) Press the OPEN control to open the storage compartment. The door will open slightly and can be moved to full open. Installing a garage door opener (if equipped) The storage compartment can be converted to accommodate a variety of aftermarket garage door openers: Remove the Velcro pad from the storage compartment door.
Page 67: Power Windows
The auxiliary power point is located on the instrument panel below the radio. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. CARGO AREA AUXILIARY POWER POINT An additional auxiliary power point is located in the cargo area. WARNING: Power outlets are designed for accessory plugs only.
Page 68 Driver Controls Press the bottom portion of the rocker switch to open. One touch down Press AUTO completely down to the second detent. The driver’s window will open fully. Depress up to stop window operation. NOTE: This feature will only operate the driver’s side window.
Page 69: Speed Control
1. Rotate the control clockwise to the right position to adjust the right mirror and rotate the control counterclockwise to the left position to adjust the left mirror. 2. Move the control in the direction you wish to move the mirror.
Page 70 Driver Controls WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery, or unpaved. You may lose control of the vehicle. WARNING: Do not shift the gearshift lever into N (Neutral) with the speed control on. You may lose control of the vehicle or cause engine system damage.
Page 71 If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RSM will re-engage it. WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery, mountainous, hilly, or unpaved.
Page 72 Driver Controls Depress the brake pedal. When the desired vehicle speed is reached, press SET ACC. To disengage speed control Depress the brake pedal or Depress the clutch pedal (if equipped). NOTE: Disengaging the speed control will not erase the previously programmed set speed.
Page 73 Driver Controls NOTE: Pressing OFF will erase the previously programmed set speed. To return to a previously set speed Press RSM. NOTE: For RSM to operate, the vehicle speed must be faster than 48 km/h (30 mph). FUEL FILLER DOOR RELEASE HANDLE Your vehicle is equipped with a locking fuel filler door.
Page 74 Driver Controls MOON ROOF (IF EQUIPPED) To operate the moon roof: The moon roof is equipped with an automatic, one-touch, express opening feature. Press and release the rear portion of the control. To stop motion at any time during the one-touch opening, press the control a second time.
Page 75 To install the shade: 1. Fasten the cover into the mounting brackets (make sure the cover is right side up). 2. Pull the end of the shade toward you and hook the sides into the notches (right side first) in the rear trim panels. WARNING: To reduce the risk of injuries, the fasteners for cargo area cover must be properly attached to the mounting clips on the rear trim panels.
Page 76 Driver Controls Do not leave the liftgate or liftgate glass open while driving. Doing so could cause serious damage to the liftgate and its components as well as allowing carbon monoxide to enter the vehicle. WARNING: Make sure that the liftgate door and/or window are closed to prevent exhaust fumes from being drawn into the vehicle.
Page 77: Locks And Security
To reinstall the cross-bar assembly to the roof rack side rails: 1. Slide the cross-bar assemblies over the end cap tongue and into the side rails. 2. Tighten thumbwheel at both ends of the cross-bar. KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer.
Page 78: Anti-Theft System
Locks and Security Childproof door locks When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of each rear door and must be set separately for each door.
Page 79 Locks and Security Unlocking the doors Press this control to unlock the driver’s door. The interior lamps will illuminate, if the switch on the overhead lamps are in the “DOOR” position. The flashers will flash twice to confirm the vehicle is unlocked.
Page 80 Take all your vehicle’s transmitters to your authorized Mazda dealer for programming, or Perform the programming procedure yourself.
Page 81 Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. NOTE: This procedure must be completed within the specified times. If not completed within the specified time period, reprograming procedures must be restarted from the beginning.
Page 82 NOTE: The SecuriLock passive anti-theft system is not compatible with non-Mazda aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is located on top of the instrument panel.
Page 83 NOTE: If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the encoded ignition key is an approved Mazda encoded ignition key.
Page 84 If two previously programmed coded keys are not available, you must bring your vehicle to your authorized Mazda dealership to have the spare coded key(s) programmed. NOTE: Please read and understand the entire procedure before you begin.
Page 85 If not successful, the new coded key(s) will not start the vehicle’s engine and the theft indicator will flash on and off and you may repeat steps 1 through 6. If failure repeats, bring your vehicle to your authorized Mazda dealership to have the new spare key(s) programmed.
Page 86 Locks and Security The system will become prearmed, when all doors are closed. When the system becomes prearmed the flashers will flash to confirm the prearming. Once the system is prearmed, the system will arm in 20 seconds. If any door is opened during these 20 seconds, the arming will be canceled.
Page 87: Seating And Safety Restraints
Seating and Safety Restraints SEATING Adjustable head restraints (if equipped) Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 88 Seating and Safety Restraints WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: Sitting in a reclined position while the vehicle is moving is dangerous because you don’t get the full protection from seat belts.
Page 89 Seating and Safety Restraints Using the manual lumbar support (if equipped) The lumbar support control is located on the inboard side of the driver’s seat. Turn the lumbar support control clockwise to increase firmness. Turn the lumbar support control counterclockwise to increase softness.
Page 90 Seating and Safety Restraints Move the rear of the control up or down to raise or lower the rear portion of the seat cushion. Move the control in the directions shown to move the seat forward, backward, up or down. REAR SEATS Head restraints (if equipped) Your vehicle’s seats may be equipped with head restraints which are...
Page 91 Seating and Safety Restraints Push control to lower head restraint. Folding down rear seats 1. Raise the rear seat head restraint and remove. 2. Place the head restraints under the front passenger seat for storage. 3. Pull the seat release control.
Page 92 Seating and Safety Restraints 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback. NOTE:When the seatback release strap is pulled use your other hand to guide the seatback.
Page 93 Seating and Safety Restraints 6. Rotate seatback down into load floor position. WARNING: Make sure seat belt buckle heads are not trapped underneath the seatback and that the seat belt buckle heads are fully extended towards the front of the vehicle. Seat belt buckle heads may break if they are trapped underneath the seatback as the seatback is...
Page 94 Seating and Safety Restraints 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed. 3. Remove the head restraints stored under the front passenger seat and return them to the original position on the seat backs.
Page 95 Seating and Safety Restraints To install the rear cushion 1. Push the cushion to the inboard side of the vehicle. 2. Make sure that the hinges are locked into place. Folding down rear seats 1. Raise the rear seat head restraint and remove.
Page 96 Seating and Safety Restraints 3. Pull the seat release control on each side of the seat to release the locks. 4. Flip seat forward. 5. Pull the seatback release strap toward the front seat. Make sure the seat belt buckle heads are fully extended towards the front of the vehicle and are away from the seatback.
Page 97 Seating and Safety Restraints Returning the rear seats to upright position 1. Pull seatback up and into upright position making sure seatback locks into place. 2. Rotate seat cushion down into the seating position making sure that the seat cushion is locked into place and that the seat belt buckles are exposed.
Page 98: Safety Restraints
Seating and Safety Restraints SAFETY RESTRAINTS Safety restraints precautions WARNING: Always drive and ride with your seatback upright and the lap belt snug and low across the hips. WARNING: To reduce the risk of injury, make sure children sit where they can be properly restrained. WARNING: Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 99 Seating and Safety Restraints WARNING: Placing a child, 12 years or younger, in the front seat is dangerous. The child could be hit by a deploying air bag and be seriously injured or even killed. A sleeping child is more likely to lean against the door and be hit by the side air bag in a moderate collision.
Page 100 Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle.
Page 101 Seating and Safety Restraints When to use the automatic locking mode Any time a child safety seat is installed in a passenger front or outboard rear seating position (if equipped). Children 12 years old and under should be properly restrained in the rear seat whenever possible.
Page 102 WARNING: After any vehicle collision, the front passenger outboard seat belt system must be checked by an authorized Mazda dealership to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function. Additionally, if the front air bags have deployed, the front pretensioners have also deployed and the front seat restraint system must be replaced.
Page 103 Seating and Safety Restraints WARNING: Position the safety belt height adjusters so that the belt rests across the middle of your shoulder. Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Safety belt pretensioner Your vehicle is equipped with safety belt pretensioners at the driver and front passenger seating positions.
Page 104 WARNING: Improper disposal of the pretensioner system or a vehicle with non-deactivated pretensioners is dangerous. Unless all safety procedures are followed, injury could result. Ask an authorized Mazda Dealer how to safely dispose of the pretensioner system or how to scrap a front pretensioner-equipped vehicle.
Page 105 Seating and Safety Restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 106 Seating and Safety Restraints Conditions of operation If... The driver’s safety belt is not buckled before the ignition switch is turned to the ON position... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition switch is turned to the ON...
Page 107 Seating and Safety Restraints Reasons given... I was in a hurry Seat belts don’t work Traffic is light Belts wrinkle my clothes The people I’m with don’t wear belts I have an air bag I’d rather be thrown clear WARNING: Do not sit on top of a buckled safety belt to avoid the Safety Belt Warning Light.
Page 108 Mazda recommends that all safety belt assemblies used in vehicles involved in a collision be replaced. However, if the collision was minor and an authorized Mazda technician finds that the belts do not show damage and continue to operate properly, they do not need to be replaced.
Page 109: Air Bags
Seating and Safety Restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) RPM X 1000 km/h Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries.
Page 110 Do not modify the front end of the vehicle. WARNING: Additional equipment may effect the performance of the air bag sensors increasing the risk of injury. Consult your authorized Mazda dealership before installation of additional equipment.
Page 111 Seating and Safety Restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. WARNING: Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 112 Seating and Safety Restraints The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the...
Page 113 WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 114 Seating and Safety Restraints Side air bag system (if equipped) WARNING: Do not place objects or mount equipment on or near the air bag cover on the side of the seatbacks of the front seats or in front seat areas that may come into contact with a deploying air bag.
Page 115 WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 116 Seating and Safety Restraints WARNING: All occupants of the vehicle including the driver should always wear their safety belts even when an air bag SRS is provided. How does the side air bag system work? The side air bag system consists of the following: An inflatable nylon bag (air bag) with a gas generator concealed...
Page 117 Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your authorized Mazda dealership. Air bags MUST BE disposed of by qualified personnel.
Page 118: Child Restraints
WARNING: Disposing of an air bag can be dangerous. Unless all safety procedures are followed, injury can result. Ask an Authorized Mazda Dealer how to safely dispose of an air bag or how to scrap an air bag equipped vehicle.
Page 119 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Mazda recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 120 Seating and Safety Restraints Booster seats should be used until you can answer YES to ALL of these questions: Can the child sit all the way back against the vehicle seat back with knees bent comfortably at the edge of the seat without slouching? Does the lap belt rest low across the hips? Is the shoulder belt centered on the shoulder and chest?
Page 121 Seating and Safety Restraints Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs.
Page 122 Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 123 Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front seat). Mazda recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 124 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 125 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 126 Seating and Safety Restraints Attaching child safety seats with tether straps Most new forward-facing child safety seats include a tether strap which goes over the back of the seat and hooks to an anchoring point. Tether straps are available as an accessory for many older safety seats. Contact the manufacturer of your child seat for information about ordering a tether strap.
Page 127 Seating and Safety Restraints 3. Locate the correct anchor for the selected seating position. NOTE:There are three tether anchors located on the headliner at the rear of the vehicle. WARNING: If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision.
Page 128 Seating and Safety Restraints Attaching safety seats with LATCH (Lower Anchors and Tethers for Children) attachments for child seat anchors Some child safety seats have two rigid or webbing mounted attachments that connect to two anchors at certain seating positions in your vehicle. When properly installed, this type of seat eliminates the need to use seat belts to attach the child seat.
Page 129 Seating and Safety Restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Follow the child seat manufacturer’s instructions to properly install a child seat with LATCH attachments. WARNING: Attach LATCH lower attachments of the child seat only to the anchors shown.
Page 130: Driving
Driving STARTING Positions of the ignition 1. LOCK, locks the gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. Warning lights illuminated.
Page 131 (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engine idle speed does not slow down automatically, have the vehicle checked by your authorized Mazda dealership. Before starting the vehicle: 1.
Page 132 Driving If starting a vehicle with a manual transmission: Make sure the parking brake is set. Push the clutch pedal to the floor. 3. Turn the key to 3 (ON) without turning the key to 4 (START). BRAKE CHECK FUEL Make sure the corresponding lights illuminate or illuminate briefly.
Page 133 1. Turn the key to 4 (START) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 3 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again.
Page 134: Brakes
Driving WARNING: If you ever smell exhaust fumes of any kind inside your vehicle, have your authorized Mazda dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and result in accident or death.
Page 135 If a “metal-to-metal,” “continuous grinding” or “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by an authorized Mazda dealership. Four-wheel anti-lock brake system (ABS) (if equipped)
Page 136 (If your brake warning lamp illuminates, have your vehicle serviced immediately by an authorized Mazda dealership.) Using four wheel ABS (if equipped) In an emergency or when maximum efficiency from the ABS is required, apply continuous force on the brake.
Page 137 The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. WARNING: Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park) (automatic transmission) or in 1 (First Gear) (manual transmission).
Page 138 Driving Uneven vehicle loading High crown in center of road High crosswinds Wheels out of alignment Loose or worn suspension components PREPARING TO DRIVE YOUR VEHICLE WARNING: Utility vehicles have a significantly higher rollover rate than other types of vehicles. WARNING: In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt.
Page 139: Transmission Operation
AUTOMATIC TRANSAXLE OPERATION (IF EQUIPPED) Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1.
Page 140 P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership.
Page 141 Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy. This feature is designed to optimize shift smoothness. NOTE:It is normal for your transaxle to shift firmly during the first few hundred kilometers (miles) of operation until the adaptive strategy has been learned.
Page 142 Driving R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward. You should always come to a complete stop before shifting into and out of R (Reverse). WARNING: Make sure the rearward path of the vehicle is unobstructed before moving the vehicle in reverse.
Page 143 O/D OFF control is pressed, there may be a transaxle electronic system malfunction. You should contact your authorized Mazda dealer as soon as possible or damage to the transaxle could occur.
Page 144 Driving 1 (First) Use 1 (First) for when added engine braking is desired when descending steep hills. The automatic transaxle will shift to the proper gear to ascend any grade without any need to shift to 1 (First). To avoid damage to the engine and/or transaxle do not go faster than 56 km/h (35 mph) when in this gear.
Page 145 2. Hold down the brake pedal. 3. Depress the clutch pedal. 4. Without depressing the accelerator pedal, turn the ignition to position 4 (START), release the ignition as soon as the engine starts. 5. Let the engine idle for a few seconds.
Page 146 Driving Upshifts when cruising (recommended for best fuel economy) Reverse Make sure that your vehicle is at a complete stop before you shift into R (Reverse). Failure to do so may damage the transaxle. Put the gearshift lever into the neutral position and wait at least three seconds before shifting into R (Reverse).
Page 147 2. Set the parking brake. 3. Shift into 1 (First). 4. Turn the ignition to position 1 (LOCK) to shut the engine off and remove the ignition key. WARNING: Do not park your vehicle in Neutral, it may move unexpectedly and injure someone. Use 1 (First) gear and set the parking brake fully.
Page 148 Driving FOUR WHEEL DRIVE (4X4) SYSTEM (IF EQUIPPED) 4x4 system general information WARNING: For important information regarding safe operation of this type of vehicle, see Preparing to drive your vehicle in this chapter. Your vehicle is equipped with a 4x4 system. This 4x4 system can use all four wheels to power the vehicle.
Page 149 The 4x4 mode indicator light illuminates only under the following conditions. If the indicator light illuminates when driving in the 4x4 AUTO mode, contact your Mazda dealer as soon as possible. The indicator light illuminates when the 4x4 ON mode is engaged.
Page 150 Driving Maintain steering wheel control at all times, especially in rough terrain. Since sudden changes in terrain can result in abrupt steering wheel motion, make sure you grip the steering wheel from the outside. Do not grip the spokes. Drive cautiously to avoid vehicle damage from concealed objects such as rocks and stumps.
Page 151 WARNING: If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your authorized Mazda dealership. Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transaxle may occur.
Page 152 Driving Avoid excessive speed because vehicle momentum can work against you and cause the vehicle to become stuck to the point that assistance may be required from another vehicle. Remember, you may be able to back out the way you came if you proceed with caution. Mud and water NOTE: If you must drive through high...
Page 153 Mazda Motor Corporation joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and other public and private lands by “treading lightly.”...
Page 154 Driving Descend a hill in the same gear you would use to climb up the hill to avoid excessive brake application and brake overheating. Do not descend in neutral, disengage overdrive or manually shift to a lower gear. When descending a steep hill, avoid sudden hard braking as you could lose control.
Page 155 Tires, Replacement Requirements Do not use a size and type of tire and wheel other than that originally provided by Mazda Motor Corporation because it can affect the safety and performance of your vehicle, which could lead to loss of vehicle control or roll over and serious injury.
Page 156 For this reason, Mazda Motor Corporation strongly recommends that you do not make modifications such as adding or removing parts (such as lift kits or stabilizer bars) or by using replacement parts not equivalent to the original factory equipment.
Page 157: Vehicle Loading
DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall. Water may also enter your engine’s air intake and severely damage your engine.
Page 158 Driving Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating is determined by subtracting the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
Page 159 WARNING: Under no circumstance should these limitations be exceeded. Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury. Special loading instructions for owners of pickup trucks and utility-type vehicles WARNING: For important information regarding safe operation of this type of vehicle, see the Preparing to drive your vehicle section in this chapter.
Page 160: Trailer Towing
Driving TRAILER TOWING Trailer towing with your vehicle may require the use of a trailer tow option package. Trailer towing puts additional loads on your vehicle’s engine, transaxle, axle, brakes, tires, and suspension. For your safety and to maximize vehicle performance, be sure to use the proper equipment while towing. Follow these guidelines to ensure safe towing procedure: Stay within your vehicle’s load limits.
Page 161 GCWR (Gross Combined Weight Rating)/Trailer Weights Engine Maximum GCWR - kg (lbs.) 2.0L w/manual 1,932 (4,260) transmission 3.0L 2,477 (5,460) w/automatic transmission 3.0L 3,175 (7,000) w/automatic transmission and towing package Notes: For high altitude operation, reduce GCW by 2% per 300 meters (100 ft.) elevation.
Page 162 Preparing to tow Use the proper equipment for towing a trailer, and make sure it is properly attached to your vehicle. See your authorized Mazda dealer. Hitches Do not use hitches that clamp onto the vehicle bumper. Use a load carrying hitch.
Page 163 Driving while you tow When towing a trailer: Turn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. Consult your local motor vehicle speed regulations for towing a trailer. To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling.
Page 164 Driving Exceeding these limits may allow water to enter critical vehicle components, adversely affecting driveability, emissions, reliability and causing internal transmission damage. Replace the rear axle lubricant any time the axle has been submerged in water. Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required.
Page 165: Roadside Emergencies
Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1: Contact Your Mazda Dealer Discuss the matter with an Authorized Mazda Dealer.
Page 166 Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Page 167: Hazard Flasher Switch
HAZARD FLASHER CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on the instrument panel by the radio. Depress hazard lights control to activate all hazard flashers simultaneously.
Page 168: Fuses And Relays
Roadside Emergencies 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. Turn the ignition to the ON position. Pause for a few seconds and return the key to the LOCK/OFF position.
Page 169 Fuse Mini Standard rating fuses fuses — — — — — — — — — — Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 170 Roadside Emergencies The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating — Passenger Compartment Fuse Panel Description Canister vent control solenoid Blower relay (coil), Rear defrost relay (coil), Pressure switch to PCM Rear wiper motor, Rear washer motor, Rear wiper relay (coil) Four-wheel drive control module, Cluster (restraints control warning) ABS unit (EVAC &...
Page 171 Fuse/Relay Fuse Amp Location Rating — Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Roadside Emergencies Passenger Compartment Fuse Panel Description Illumination for: Cluster, Heater unit, Radio, Hazard switch, Rear defrost...
Page 172 Roadside Emergencies WARNING: Always disconnect the battery before servicing high current fuses. WARNING: To reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and specifications chapter.
Page 173 The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Location Rating Horn H/L LH 15A* H/L RH 15A* HEGO 15A* FUEL 20A* DIODE — DIODE — H/L RELAY — MICRO — — 30A** MAIN 120A 15A* (DRL) 15A* 15A*(DRLZ) (DRLZ) (HELV) 10A(HLEV) PWR 1...
Page 174 Roadside Emergencies Fuse/Relay Fuse Amp Location Rating BTN 1 40A** (ABS) 60A** BTN 2 40A** MAIN FAN 40A** (2.0L) 50A(3.0L) R DEF 30A** ADD FAN 40A**(2.0L) 50A(3.0L) EEC MAIN ISO — FUEL PUMP ISO — MAIN FAN ISO — ADD FAN ISO —...
Page 175 TEMPORARY SPARE TIRE INFORMATION The temporary spare tire for your vehicle is labeled as such. It is smaller than a regular tire and is designed for emergency use only. WARNING: If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others.
Page 176 Roadside Emergencies WARNING: If you use the temporary spare tire continuously or do not follow these precautions, the tire could fail, causing you to lose control of the vehicle, possibly injuring yourself or others. When driving with the temporary spare tire do not: exceed 80 km/h (50 mph) under any circumstances load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label...
Page 177 1. Park on a level surface, activate hazard flashers and place gearshift lever in P (Park) (automatic transmission) or R (Reverse) (manual transmission). 2. Set the parking brake and turn engine OFF. 3. Block the diagonally opposite wheel. 4. Lift the cargo cover and remove the tool bag with jack handle, lug nut wrench and long spare tire rod and spare tire from the...
Page 178 Roadside Emergencies Before placing the jack under the vehicle, NOTE the jack locations: Front jacking notches are located under the front suspension arm. Rear jacking notches are located under the rear trailing arm. 6. Position the jack according to the following guides and turn the jack handle clockwise until the tire is a maximum of 25 mm (1 inch) off the ground.
Page 179 Never use the differentials as a jacking point. It is too easy for the vehicle to tilt or fall and you can be injured. WARNING: To lessen the risk of personal injury, do not put any part of your body under the vehicle while changing a tire.
Page 180: Jump Starting
Roadside Emergencies NOTE: To stow the full size flat tire in the cargo floor, the long spare tire rod in the tool bag needs to be installed. 11. Using the lug wrench, remove the spare tire rod from the cargo floor and install the longer spare tire rod.
Page 181 Preparing your vehicle When the battery is disconnected or a new battery is installed, the transmission must relearn its shift strategy. As a result, the transmission may have firm and/or soft shifts. This operation is considered normal and will not affect function or durability of the transmission. Over time, the adaptive learning process will fully update transmission operation.
Page 182 Roadside Emergencies 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery. 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery.
Page 183 4. Make the final connection of the negative (-) cable to an exposed metal part of the disabled vehicle’s engine, away from the battery and the fuel injection system. NOTE: Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. WARNING: Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 184 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 185 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 186: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift and dollies or flatbed equipment. Do not tow with a slingbelt. Mazda has not approved a slingbelt towing procedure.
Page 187 In case of a roadside emergency with a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle (regardless of powertrain configuration) can be flat towed (all wheels on the ground) under the following conditions: Place the transmission in N (Neutral).
Page 188: Customer Assistance
Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1: Contact Your Mazda Dealer Discuss the matter with an Authorized Mazda Dealer.
Page 189 CUSTOMER ASSISTANCE (CANADA) Your complete and permanent satisfaction is our business. We are here to serve you. All Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. In our experience, any questions, problems or complaints regarding the operation of your Mazda or any other general service transactions are most effectively resolved by your dealer.
Page 190 Your complete satisfaction is the goal of Mazda Canada Inc. and our dealers. Mazda’s participation in CAMVAP makes a valuable contribution to our achieving that goal.
Page 191 British Columbia & Yukon Territories Alberta & Northwest Territories Saskatchewan Manitoba Ontario Atlantic Canada Quebec REGIONAL OFFICES Regional Offices Mazda Canada Inc. Western Region 8171 Ackroyd Road Suite 2000 Richmond, B.C. V6X 3K1 (604) 303–5670 Mazda Canada Inc. Central/Atlantic Region 305 Milner Avenue Suite 400 Scarborough, Ontario.
Page 192 Authorized Mazda Dealers have the knowledge and the tools to keep your Mazda vehicle in top condition. If you have any questions or recommendations for improvement regarding the service of your Mazda vehicle or servicing by Mazda Dealer personnel, we recommend that you take the following steps: STEP 1 Discuss the matter with an Authorized Mazda Dealer.
Page 193 P.O. Box 1120, Pago Pago, American Samoa 96799 TEL: (684) 699–9347 ADD-ON NON-GENUINE PARTS AND ACCESSORIES Non-genuine parts and accessories for Mazda vehicles can be found in stores. These may fit your vehicle, but they are not approved by the...
Page 194 Mazda assumes no responsibility for death, injury, or expenses that may result from the installation of add-on non-genuine parts or accessories. WARRANTIES FOR YOUR MAZDA...
Page 195 NHTSA, U.S. Department of Transportation. Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hotline. (Note) If you live in the U.S.A., all correspondence to Mazda Motor Corporation should be forwarded to: Mazda North American Operations 7755, Irvine Center Drive Irvine, California 92618–2922...
Page 196 Customer Assistance If you live outside of the U.S.A., please contact the nearest Mazda Distributor. ( See the Mazda Importers/Distributors section of this manual). SERVICE PUBLICATIONS Factory-authorized Mazda service publication are available for owners who wish to do some of their own maintenance and repair.
Page 197: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer or Mazda Corporation. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (202–366–0123 in the Washington D.C.
Page 198: Cleaning
Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Detail Wash (ZC-3–A), which is available from your dealer. Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 199 Never spray the engine or other engine components with water. Water will damage the engine or other engine components. Spray Engine Shampoo and Degreaser, available at your local Mazda dealer, on all parts that require cleaning and pressure rinse clean.
Page 200 Mazda dealer. If tar or grease spots are present, use Extra Strength Tar and Road Oil Removal, available at your local Mazda dealer. WINDOWS AND WIPER BLADES The windshield, rear window and wiper blades should be cleaned...
Page 201 For fabric, carpets, cloth seats, safety belts and seats equipped with side air bags: Remove dust and loose dirt with a vacuum cleaner. Remove light stains and soil with Extra Strength Upholstery Cleaner, available at your local Mazda dealer. Cleaning...
Page 202 Cleaning If grease or tar is present on the material, spot-clean the area first with Spot and Stain Remover, available at your local Mazda dealer. Never saturate the seat covers with cleaning solution. Do not use household cleaning products or glass cleaners, which can stain and discolor the fabric and affect the flame retardant abilities of the seat materials.
Page 203: Maintenance And Specifications
Mazda workmanship. Any auto repair shop using parts equivalent to your Mazda’s original equipment may perform maintenance. But we recommend that it always be done by an Authorized Mazda Dealer using genuine Mazda parts.
Page 204 Maintenance and Specifications SCHEDULE 1 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), Months Maintenance Item x 1000 Km (x 1000 Miles) (7.5) (15) (22.5) (30) (37.5) (45) (52.5) (60) (67.5) (75) (82.5) (95) ENGINE...
Page 205 *1 According to state and federal regulations, failure to perform maintenance on these items will not void your emissions warranties. However, Mazda recommends that all maintenance services be performed at the recommended time or mileage (kilometrage) period to ensure long-term reliability.
Page 206 Maintenance and Specifications SCHEDULE 2 I: Inspect and repair, clean, adjust, or replace if necessary (Oil-permeated air filter cannot be cleaned using the air-blow method) R: Replace L: Lubricate Maintenance Interval (Number of months or km (miles), Months Maintenance Item x 1000 Km (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) ENGINE...
Page 207 Maintenance and Specifications Maintenance Interval (Number of months or km (miles), Months Maintenance Item x 1000 Km (x 1000 Miles) (5) (10) (15) (20) (25) (30) (35) (40) (45) (50) (55) (60) Engine coolant Replace at first 72,000 km (45,000 miles) or 36 months;...
Page 208 Check your “Warranty Information” to find out which parts and services are covered. Use only recommended fuels, lubricants, fluids and service parts conforming to specifications. Genuine Mazda parts are designed and built to provide the best performance in your vehicle. PRECAUTIONS WHEN SERVICING YOUR VEHICLE Be especially careful when inspecting or servicing your vehicle.
Page 209 Maintenance and Specifications Working with the engine off Automatic transmission: 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Turn off the engine and remove the key. 3. Block the wheels to prevent the vehicle from moving unexpectedly. Manual transmission: 1.
Page 210 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. At the front of the vehicle, lift up on the auxiliary latch handle located in the center between the hood and the grille. 3.
Page 211: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 2.0L DOHC I4 Zetec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Brake/Clutch fluid reservoir 4. Air filter assembly 5. Power distribution box 6. Battery 7. Engine oil filler cap 8.
Page 212 Maintenance and Specifications 3.0L DOHC V6 Duratec engine 1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Automatic transmission fluid dipstick 4. Brake fluid reservoir 5. Air filter assembly 6. Power distribution box 7. Battery 8. Engine oil dipstick 9.
Page 213: Engine Oil
Add fluid to fill the reservoir if the level is low. In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Mazda specifications. Refer to Refill capacities in this chapter. NOTE: State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 214 Maintenance and Specifications 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 2.0L DOHC I4 Zetec engine 3.0L DOHC V6 Duratec engine 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
Page 215 Maintenance and Specifications If the oil level is below the MIN or ADD mark, add enough oil to raise the level within the MIN–MAX or ADD-FULL range. 2.0L DOHC I4 Zetec engine 3.0L DOHC V6 Duratec engine Oil levels above the MAX or FULL mark may cause engine damage. Some oil must be removed from the engine by a service technician.
Page 216 If a replacement oil filter is used that does not meet Mazda material and design specifications, start-up engine noises or knock may be experienced. It is recommended you use the appropriate Genuine Mazda oil filter (or another brand meeting Mazda specifications) for your engine application.
Page 217: Battery
Maintenance and Specifications BATTERY Your vehicle is equipped with a Mazda maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the service maintenance section for the service interval schedules.
Page 218 Maintenance and Specifications WARNING: When lifting a plastic-cased battery, excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery. Lift the battery with a battery carrier or with your hands on opposite corners.
Page 219 Maintenance and Specifications transmission may shift firmly. This operation is considered normal and will not affect function or durability of the transmission. Over time the adaptive learning process will fully update transmission operation to its optimum shift feel. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected.
Page 220 Maintenance and Specifications When the engine is cold, check the level of the engine coolant in the reservoir. The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
Page 221 To maintain the integrity of the coolant and the cooling system and maintain the warranty on the cooling system: Add Mazda Premium Engine Coolant or the type of coolant originally equipped in your vehicle. If you are unsure which type of coolant your vehicle requires, check your coolant reservoir or contact your local dealer.
Page 222 Maintenance and Specifications WARNING: To reduce the risk of personal injury, make sure the engine is cool before unscrewing the coolant pressure relief cap. The cooling system is under pressure; steam and hot liquid can come out forcefully when the cap is loosened slightly. 1.
Page 223 Not all coolant recycling processes produce coolant which meets Mazda recommend coolants. Use of a recycled engine coolant which does not meet the Mazda recommended coolant, may harm engine and cooling system components. Always dispose of used automotive fluids in a responsible manner.
Page 224: Fuel Information
Maintenance and Specifications Refer to the chart on the coolant container to ensure the coolant concentration in your vehicle will provide adequate protection at the temperatures in which you drive. Vehicles driven year-round in non-extreme climates should use a 50/50 mixture of engine coolant and distilled water for optimum cooling system and engine protection.
Page 225 Maintenance and Specifications WARNING: Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Page 226 However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, see your authorized Mazda dealer to prevent any engine damage. Fuel quality NOTE:If you are experiencing starting, rough idle or hesitation...
Page 227 World-wide Fuel Charter. In Canada, look for fuels that display the Auto Makers’ Choice Cleaner air Mazda endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 228 Fuel Filter For fuel filter replacement, see your authorized Mazda dealership. Refer to the service maintenance section for the appropriate intervals for changing the fuel filter.
Page 229 Maintenance and Specifications ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver. You must gather information as accurately and consistently as possible. Fuel expense, frequency of fillups or fuel gauge readings are NOT accurate as a measure of fuel economy.
Page 230 Maintenance and Specifications 2. Each time you fill the tank, record the amount of fuel added (in liters or gallons). 3. After at least three to five tank fill-ups, fill the fuel tank and record the current odometer reading. 4. Subtract your initial odometer reading from the current odometer reading.
Page 231 Maintenance and Specifications Warming up a vehicle on cold mornings is not required and may reduce fuel economy. Resting your foot on the brake pedal while driving may reduce fuel economy. Combine errands and minimize stop-and-go driving. Maintenance Keep tires properly inflated and use only recommended size. Operating a vehicle with the wheels out of alignment will reduce fuel economy.
Page 232 If other than Mazda authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Mazda parts should be equivalent to genuine Mazda parts in performance and durability. WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover.
Page 233 Maintenance and Specifications Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working.
Page 234 Maintenance and Specifications CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the service maintenance section for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 235 MAX. Do not fill above this line. 4. Use only brake fluids certified to meet Mazda specifications. Refer to Lubricant specifications in this chapter. DOT 3 fluid is recommended. However, if DOT 3 is not available, DOT 4 fluid can be used.
Page 236 Maintenance and Specifications TRANSMISSION FLUID Checking automatic transmission fluid Refer to your scheduled maintenance section for scheduled intervals for fluid checks and changes. Your transaxle does not consume fluid. However, the fluid level should be checked if the transaxle is not working properly, i.e., if the transaxle slips or shifts slowly or if you notice some sign of fluid leakage.
Page 237 Maintenance and Specifications The transmission fluid should be in the crosshatch zone if at normal operating temperature (66°C-77°C [150°F-170°F]). High fluid level Fluid levels above the crosshatch zone may result in transaxle failure. An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage.
Page 238: Air Filter(S)
Seek medical attention immediately. AIR FILTER MAINTENANCE Refer to the service maintenance section for the appropriate intervals for changing the air filter element. When changing the air filter element, only use a Genuine Mazda air filter element.
Page 239 Maintenance and Specifications WARNING: Do not start your engine with the air cleaner removed and do not remove it while the engine is running. Changing the air filter element 1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover.
Page 240 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Mazda to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 241 Maintenance and Specifications WARNING: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge.
Page 242 Maintenance and Specifications Four tire rotation Five tire rotation Replacing the tires Replace the tires when the wear band is visible through the tire treads.
Page 243 WARNING: Make sure that all replacement tires are of the same size, type, load=carrying capacity and tread (e.g., “All Terrain”, etc.), as originally offered by Mazda. Failure to do so can result in tire failure and a serious accident. WARNING: Do not replace your tires with “high performance”...
Page 244: Refill Capacities
Maintenance and Specifications Drive cautiously. If you hear the chains rub or bang against the vehicle, stop and retighten them. If this does not work, remove the cables to prevent vehicle damage. Avoid overloading your vehicle. Remove the tire chains when they are no longer needed. Do not use chains on dry roads.
Page 245 GL-5, SAE 75W-90 MERCON ATF Transfer Case SAE 75W-140 Synthetic Lubricant API service GL-5, SAE 80W-90 Engine coolant Mazda green-colored or yellow-colored Premium Engine Coolant Rear axle SAE 80W-90 lubricant Premium Rear Axle Lubricant Windshield washer fluid Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.
Page 246: Engine Data
Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant in this chapter. Fill to 6 mm to 14 mm (1/4 inch to 9/16 inch) below bottom of fill hole. For further information on your lubrication specifications, see your authorized Mazda dealer. WHEEL AND TIRE SIZES Vehicle Wheel...
Page 247 Maintenance and Specifications VEHICLE DIMENSIONS Dimensions (1) Vehicle height/ Maximum height* (2) Front track / rear (3)Overall width (body) (4) Wheelbase (5)Overall length * Denotes a 4x4 vehicle with optional 16” tires 4 Door mm (in.) 1,681 (66.2)/1,744 (68.7)* 1,550 (61.0)/1,530 (60.2) 1,783 (70.2) 2,620 (103.1) 4,394 (173.0)
Page 248 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’s side.
Page 249 Maintenance and Specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, transmission, frame and...
Page 250: Accessories
CELL PHONES Use of cell phones and other devices by driver: WARNING: Although not Mazda products, use of any electrical devices such as cell phones, computers, portable radios, vehicle navigation or other devices by the driver while the vehicle is moving is dangerous.
Page 251: Index
ABS (see Brakes) ...135 Air bag supplemental restraint system ...109, 114 and child safety seats ...111 description ...109, 114 disposal ...113, 117 driver air bag ...111, 116 indicator light ...12, 113, 117 operation ...111, 116 passenger air bag ...111, 116 side air bag ...114 Air cleaner filter ...238–239 Air conditioning...
Page 252 Index waxing ...198 wheels ...199 wiper blades ...200 woodtone trim ...201 Climate control (see Air conditioning or Heating) ...50 Clock ...30, 45 Clutch fluid ...238 operation while driving ...144 recommended shift speeds ...145 Console ...74 overhead ...65–66 Controls power seat ...89 Coolant checking and adding ...219 refill capacities ...223, 244...
Page 253 preparing to drive your vehicle ...138 Fuel ...224 calculating fuel economy ...229 cap ...15, 227 capacity ...244 choosing the right fuel ...226 comparisons with EPA fuel economy estimates ...231 detergent in fuel ...227 filling your vehicle with fuel ...224, 227, 229 filter, specifications ...228 fuel filler door release ...73 fuel pump shut-off switch ...167...
Page 254 Index lighting up panel and interior ...55 location of components ...10 Jump-starting your vehicle ...180 Keys ...82–84 key in ignition chime ...15 positions of the ignition ...130 Lamps bulb replacement specifications chart ...58 cargo lamps ...55 daytime running light ...54 fog lamps ...55 headlamps ...54 headlamps, flash to pass ...55...
Page 255 Panic alarm feature, remote entry system ...79 Parking ...146 Parking brake ...136 Power distribution box (see Fuses) ...171 Power door locks ...77 Power point ...66–67 Power Seats ...89 Power steering ...137 fluid, checking and adding ...234 fluid, refill capacity ...244 fluid, specifications ...246 Power Windows ...67 Preparing to drive your...
Page 256 Index changing ...175–176 checking the pressure ...241 replacing ...242 rotating ...241 snow tires and chains ...243 tire grades ...240 treadwear ...240 Towing ...160 recreational towing ...164 trailer towing ...160 wrecker ...186 Transaxle automatic operation ...139 fluid, checking and adding (manual) ...238 manual operation ...144 Transmission fluid, checking and adding...

Mazda 2002 Tribute Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Locks and Security

Seating and Safety Restraints

Driving

Roadside Emergencies

Customer Assistance

Cleaning

Maintenance and Specifications

Accessories

Index

Quick Links

Table of Contents

Related Manuals for Mazda 2002 Tribute

Summary of Contents for Mazda 2002 Tribute

Table of Contents