Page 1 Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 2: Introduction
Introduction ICONS Indicates a warning. Read the following section on Warnings for a full explanation. Indicates vehicle information related to recycling and other environmental concerns will follow. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards protecting the environment.
Page 3 SPECIAL NOTICES Using your vehicle as a snowplow Do not use this vehicle for snowplowing. Using your vehicle as an ambulance Do not use this vehicle as an ambulance. Your vehicle is not equipped with the Ford Ambulance Preparation package. Notice to owners of utility type vehicles Before you drive your vehicle, please read this Owner’s Guide carefully.
Page 4: Instrumentation
Instrumentation Turn signal and wiper/washer control (pg. 33) Headlamp control (pg. 18) INT 2 INT 1 PANEL PULL Rear window defroster control (pg. 20) Instrument panel dimmer switch (pg. 19) Instrument cluster (pg. 6) FUEL DOOR AJAR BRAKE RESUME SET ACCEL COAST Speed control Parking brake...
Page 5: Radio Controls
Clock (pg. 21) VOL-PUSH ON MAX A/C A4WD Radio controls (pg. 41) 4WD control* Climate controls (pg. 41) Electronic sound system; refer to Audio Guide (pg. 21) FM 1 FM 1 BASS TREB SEEK DOLBY 8 NR SCAN TAPE CD TUNE DISCS SIDE 1-2...
Page 6: Warning Lights And Chimes
Instrumentation WARNING LIGHTS AND CHIMES FUEL DOOR AJAR BRAKE Low fuel Illuminates when the fuel level is low. The lamp will also illuminate when the ignition key is turned to ON and the engine is off. Check engine Your vehicle is equipped with a computer that monitors the engine’s emission control system.
Page 7 What you should do if the check engine light illuminates Light turns on solid: This means that the OBD II system has detected a malfunction. Temporary malfunctions may cause your Check Engine light to illuminate. Examples are: 1. The vehicle has run out of fuel. (The engine may misfire or run poorly.) 2.
Page 8 Instrumentation Safety belt Momentarily illuminates when the ignition is turned ON to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Brake system warning Momentarily illuminates when the BRAKE ignition is turned ON and the engine is off.
Page 9 High beams Illuminates when the high beam headlamps are turned on. SecuriLock anti-theft system This light indicates the anti-theft alarm system is armed. Refer to Anti-theft system in the Controls and features chapter. Momentarily illuminates when the ignition is turned to ON/START. If the light fails to illuminate, continues to flash or remains on, have the system serviced.
Page 10 Instrumentation check the engine coolant temperature gauge and the engine oil pressure gauge. Refer to Engine coolant temperature gauge and Engine oil pressure gauge in this chapter for more information. Four wheel drive low (if equipped) Illuminates when four-wheel drive low is engaged.
Page 11 Instrumentation Low washer fluid Illuminates when the ignition is turned to ON and when the windshield washer fluid is low. WASH Door ajar Illuminates when the ignition switch is in the ON or START position and DOOR any door is open. AJAR Fuel reset Illuminates when the ignition key is...
Page 12: Fuel Gauge
Instrumentation Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and either front door is opened. GAUGES FUEL DOOR AJAR BRAKE Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position).
Page 13 Speedometer Indicates the current vehicle speed. Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Page 14: Trip Odometer
Instrumentation Odometer Registers the total kilometers (miles) of the vehicle. Trip odometer Registers the kilometers (miles) of individual journeys. To reset, depress the control. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer in the red zone may damage the engine.
Page 15 Instrumentation Battery voltage gauge This gauge shows the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range (as indicated), have the vehicle’s electrical system checked as soon as possible. Engine oil pressure gauge This shows the engine oil pressure in the system.
Page 16 Instrumentation Selectable features English/metric display Press this control to change the trip computer display from metric to English units. Press again to change from English to metric units. Mode control Each press of the MODE control will display a different feature as follows: Compass display.
Page 17 Average fuel economy. The display will indicate the vehicle’s average fuel economy in liters/100 km (or miles/gallon) since last reset. To reset the average fuel economy: 1. Press the MODE control repeatedly until AVG F/ECON is displayed (no other display is resettable).
Page 18: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the desired position: — OFF. — Parking lamps on. — Headlamps on. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamps are in the position.
Page 19 PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel. Rotate up to brighten. Rotate down to dim. AUTOLAMP CONTROL The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on for a preselected period of time after the ignition switch is...
Page 20 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the defroster control to clear the rear window of thin ice and fog. The small LED will illuminate when the defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
Page 21: Audio System
CLOCK Press H to set the hour. Press M to set the minute. AUDIO SYSTEM Refer to the “Audio Guide” for instructions on how to operate the audio system. CLIMATE CONTROL SYSTEM Electronic Automatic Temperature Control (EATC) system The EATC system will maintain a selected temperature and automatically control airflow.
Page 22: Automatic Operation
Controls and features Turning the EATC on Press AUTOMATIC, any of the override controls or the fan speed AUTO control. The EATC will only operate OUTSIDE TEMP AUTOMATIC when the ignition is in the ON MAX A/C VENT PNL • FLR FLOOR FLR •...
Page 23 Temperature selection The display window indicates the selected temperature, function (AUTO or one of the override controls) and manual control of fan speed ( ) if automatic fan speed is not desired. To control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons.
Page 24 Controls and features Fan speed ( When AUTOMATIC is pressed, fan speed is adjusted automatically for existing conditions. You can override fan speed at any time. To control fan speed manually, use the AUTOMATIC thumbwheel or steering wheel control to cancel automatic fan speed operation.
Page 25 Under normal conditions, your vehicle’s climate control system should be left in any position other than MAX A/C or OFF when the vehicle is parked. This allows the vehicle to “breathe” through the outside air inlet duct. MAX A/C-Uses recirculated air to cool the vehicle. The temperature will display 16°C (60°F).
Page 26 Controls and features Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to the window.
Page 27 Remove any snow, ice or leaves from the air intake area (at the bottom of the windshield). If your vehicle has been parked with the windows closed during hot weather, the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open.
Page 28 Controls and features Turn the fan speed control to the desired position. Select for air to flow through these vents: - VOLUME + MODE SEEK MEMORY – VOLUME BAND SEEK MEMORY...
Page 29 Controls and features Select for air to flow through these vents: – VOLUME BAND SEEK MEMORY Auxiliary A/C-heater controls (if equipped) The auxiliary A/C-heater feature provides increased capacity to quickly heat or cool the vehicle. Besides the driver’s overhead control panel for the front seat occupants, the second row auxiliary A/C-heater controls allow the rear passengers to control the...
Page 30 Controls and features In order for the auxiliary A/C-heater controls to function, the driver’s auxiliary A/C-heater control must be set to REAR. REAR COOL WARM PANEL FLOOR The instrument panel climate controls must be on in order for the AUTO auxiliary A/C-heater to operate.
Page 31 Turn the fan speed control knob to the desired speed. Turn the temperature control to the desired temperature. You can get warm or cool air through either the overhead registers or floor vent by turning the auxiliary mode selector: Far left for airflow to the overhead registers.
Page 32 Controls and features Anywhere between PANEL and FLOOR to vary airflow between the outlets. POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal.
Page 33 TURN SIGNAL CONTROL Push down to activate the left turn signal. Push up to activate the right turn signal. SPEED CONTROL To turn speed control on Press ON. Vehicle speed cannot be controlled until the vehicle is traveling at or above 48 km/h (30 mph).
Page 34 Controls and features To turn speed control off Press OFF or Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed Press SET ACC/SET ACCEL. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30 mph).
Page 35 If you drive up or down a steep hill, your vehicle speed may vary momentarily slower or faster than the set speed. This is normal. Speed control cannot reduce the vehicle speed if it increases above the set speed on a downhill. If your vehicle speed is faster than the set speed while driving on a downhill, you may want to shift to the next lower gear or apply the brakes to reduce your vehicle speed.
Page 36 Controls and features To set a lower set speed Press and hold CST/COAST. Release the control when the desired speed is reached or Press and release CST/COAST. Each press will decrease the set speed by 1.6 km/h (1 mph) or Depress the brake pedal.
Page 37 Controls and features To disengage speed control Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed.
Page 38 Controls and features To return to a previously set speed Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down.
Page 39 Controls and features Never adjust the steering wheel when the vehicle is moving. HAZARD FLASHER For information on the hazard flasher control, refer to Hazard lights control in the Roadside emergencies chapter. WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position.
Page 40 Controls and features INT 2 — One second interval rear wiper. INT 1 — Ten second interval rear wiper. OFF — Rear wiper and washer off. HIGH BEAMS Push forward to activate. FLASH TO PASS Pull toward you to activate and release to deactivate.
Page 41 The transmission will operate in gears one through three. To return to normal overdrive mode, press the Transmission Control Switch again. The TCIL (the word OFF) will no longer be illuminated. When you shut off and re-start your vehicle, the transmission will automatically return to normal (Overdrive) mode.
Page 42 Controls and features OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package. Forward storage bin (if equipped) Press the release control to open the storage compartment. The door will open slightly and can be moved to full open.
Page 43 One-touch moon roof (if equipped) Press and release the rear portion of the moon roof control to open. Press and hold (as desired) the front portion of the moon roof control to close. To halt motion at any point during one-touch opening, press the control a second time.
Page 44 Controls and features vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment. Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map.
Page 45 Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle. 2.
Page 46 Controls and features AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror. When the mirror detects bright light from front or behind, it will automatically adjust to minimize glare.
Page 47 Controls and features Programming 1. Prepare for programming the HomeLink Universal Transmitter by erasing all three of the factory default channels by holding down the two outside controls until the red light begins to flash (20-30 seconds). Release both controls. 2.
Page 48 Controls and features If you are programming from one of these hand-held transmitters: continue to hold the control on the HomeLink Universal Transmitter re-press the hand-held transmitter every two seconds You may have to repeat this function several times while programming. Operating the HomeLink Universal Transmitter Once programmed, the HomeLink Universal Transmitter can be used in...
Page 49 Controls and features 3. Press the programmed HomeLink control in the vehicle until the training light on the garage door receiver turns solid (1-2 seconds). Release the HomeLink control and repress to turn off the training light. 4. Press the HomeLink control again.
Page 50 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. Press the top portion of the rocker switch to close. Press the bottom portion of the rocker switch to open. AUTO AUTO...
Page 51 One touch down Press AUTO and release quickly. The window will open fully. Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the right side of the control.
Page 52 Controls and features POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. Autolock This feature automatically locks all doors when: all vehicle doors, liftgate and liftgate window are closed the ignition switch is in the ON position you shift into or through R (Reverse) the brake pedal is released.
Page 53 Controls and features 5. Turn the ignition back to ON. The horn will chirp. 6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated.
Page 54 Controls and features 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Heated outside mirrors Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated.
Page 55 Use only soft cups in the cupholder. Hard objects can injure you in a collision. The auxiliary power point is located on the instrument panel. Do not plug optional electrical accessories into the cigarette lighter. Use the power point. COMPACT DISC CHANGER (IF EQUIPPED) The compact disc changer is located inside the front center console.
Page 56 Your vehicle is equipped with a coded-key anti-theft system. Only the correct key will be able to start your vehicle. If your keys are lost or stolen, you must take your vehicle to a Ford/Lincoln-Mercury dealership for re-programming. Programming additional keys If you need additional keys electronically coded for your vehicle, spares can be purchased (a maximum of 16 keys can be programmed).
Page 57 2. Within 15 seconds of turning ignition off, insert the new coded key into the ignition and turn it from OFF to ON or START. If successful, the THEFT indicator light will illuminate for two seconds. Repeat procedure for all new keys. If key coding fails, the THEFT indicator light will flash.
Page 58 Controls and features Locking the doors Press this control to lock all doors. To confirm all doors are closed and locked, press the control a second time within five seconds. The doors will lock again, the horn will chirp and the lamps will flash. If any of the doors are ajar, the horn will make two quick chirps, reminding you to properly close all...
Page 59 battery weakness due to time and use weather conditions nearby radio towers structures around the vehicle other vehicles parked next to the vehicle To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring.
Page 60 Controls and features not be set to the OFF position for the illuminated entry system to operate. The inside lights will not turn off if: they have been turned on with the dimmer control or any door is open. Battery saver will shut off the interior lamps 40 minutes after the last door is closed.
Page 61 Controls and features 2. Press the power door unlock switch three times. 3. Turn the ignition key from ON to OFF. 4. Press the power door unlock switch three times. 5. Turn the ignition switch back to ON. The horn will chirp. 6.
Page 62: Seating And Safety Restraints
Seating and safety restraints SEATING Head restraints Push or pull the head rests to the desired position. Using the manual lumbar support Turn the lumbar support control counterclockwise to increase firmness. Turn the lumbar support control clockwise to increase softness. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 63 Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Press to raise or lower the front portion of the seat cushion. Press to raise or lower the rear portion of the seat cushion. Press the control to move the seat forward, backward, up or down.
Page 64 Seating and safety restraints Memory seats (if equipped) This system allows automatic positioning of the driver seat and outside rearview mirrors to three programmable positions. The memory seat control is located on the driver door. To program position one, move the driver seat to the desired position using the seat controls.
Page 65 Seating and safety restraints REAR SEATS Head restraints Push or pull the head rests to the desired position. Rear folding bench seat (if equipped) Folding down the rear seats Ensure that no objects such as books, purses or briefcases are on the floor in front of the second row seats before folding them down.
Page 66 Seating and safety restraints 4. Once the second row seats are in the down position, the front seats may be readjusted. Returning the seat to upright Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched, the seat may cause injury during a sudden stop.
Page 67 Third row seat (if equipped) The third row seat is equipped with combination lap and shoulder belts in the outboard seating positions and a manual adjust tongue lap belt in the center seating position. For information on the proper operation of the safety restraints, refer to Safety Restraints in this chapter.
Page 68 Seating and safety restraints Removing the third row seat From the rear of the vehicle, with the liftgate open: 1. Disengage the lap/shoulder belt from the floor by inserting a key or small screwdriver through the hole in the boot of the detachable anchor.
Page 69 3. Use the black plastic clip (located just above the detachable anchor) to stow the loose seat belt. Pull the seat release lever located on the lower right side of the seatback while pushing the seatback down into the seat cushion.
Page 70 Seating and safety restraints When reinstalling a rear seat in your vehicle it must be placed in its original position. Improper installation of the seat will prevent correct use of the safety belts and could increase the risk of injury. Refer to the warning label on the seat belt.
Page 71 SAFETY RESTRAINTS Safety restraints precautions Always drive and ride with your seatback upright and the lap belt snug and low across the hips. To prevent the risk of injury, make sure children sit where they can be properly restrained. Never let a passenger hold a child on his or her lap while the vehicle is moving.
Page 72 Seating and safety restraints Combination lap and shoulder belts 1. To fasten, insert the tongue into the slot in the buckle. 2. To unfasten, push the red release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts.
Page 73 Automatic locking mode In this mode, the shoulder belt is automatically pre-locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is not available on the driver safety belt. When to use the automatic locking mode When a tight lap/shoulder fit is desired.
Page 74 Seating and safety restraints Grasp the shoulder portion and pull downward until the entire belt is extracted. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Page 75 Seating and safety restraints Insert the tongue into the correct buckle. To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. To tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips.
Page 76 Seating and safety restraints Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front passenger. Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder. To lower the shoulder belt height, push the button and slide the height control down.
Page 77 Conditions of operation If... The driver’s safety belt is not buckled before the ignition key is turned to ON... The driver’s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The driver’s safety belt is buckled before the ignition key is turned to ON...
Page 78 Seating and safety restraints AIR BAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS) Important supplemental restraint system (SRS) precautions The supplemental restraint system is designed to: work with the safety belt to protect the driver and right front passenger. reduce certain upper body injuries.
Page 79 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln-Mercury dealer. Children and air bags For additional important safety information, read all information on safety restraints in this guide.
Page 80 Seating and safety restraints How does the air bag supplemental restraint system work? The SRS is designed to activate when the vehicle sustains sufficient longitudinal deceleration. The fact that the air bags did not inflate in a collision does not mean that something is wrong with the system.
Page 81 If the air bag is inflated, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision. The SRS consists of: driver and passenger air bag modules (which include the inflators and air bags), one or more impact and safing sensors,...
Page 82 Seating and safety restraints Disposal of air bags and air bag equipped vehicles For disposal of air bags or air bag equipped vehicles, see your local dealership or qualified technician. Air bags MUST BE disposed of by qualified personnel. SAFETY RESTRAINTS FOR CHILDREN Important child restraint precautions You are required by law to use safety restraints for children in the U.S.
Page 83 Do not leave children, unreliable adults, or pets unattended in your vehicle. To improve the fit of lap and shoulder belts on children who have outgrown child safety seats, Ford recommends use of a belt-positioning booster seat that is labelled as conforming to all Federal motor vehicle safety standards.
Page 84 Seating and safety restraints Put the safety belt in the automatic locking mode. Refer to Automatic locking mode. Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage.
Page 85 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 86 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 87 Tether anchorage hardware kits (part number 613D74) including instructions, may be obtained at no charge from any Ford or Lincoln-Mercury dealer. Tether anchor brackets may also be installed to the floor behind the second row seats.
Page 88: Starting
Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the ignition system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 89 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. Turn the key to 4 (ON) without turning the key to 5 (START).
Page 90: Starting The Engine
Starting FUEL DOOR AJAR BRAKE Make sure the corresponding lights illuminate briefly. If a light fails to illuminate, have the vehicle serviced. If the driver’s safety belt is fastened, the light ( STARTING THE ENGINE 1. Turn the key to 5 (START) without pressing the accelerator pedal and release as soon as the engine starts.
Page 91 Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. They are strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below. For best results, plug the heater in at least three hours before starting the vehicle.
Page 92 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 93: Driving
Driving BRAKES Your brakes are self-adjusting. Refer to the “Service Guide” for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 94 Driving ABS warning lamp warning lamp in the instrument cluster illuminates for about five seconds when starting the vehicle. If an ABS fault is detected, the light will remain on and your vehicle should be serviced as soon as possible. Normal braking is still effective unless the BRAKE warning lamp is also illuminated.
Page 95 Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released.
Page 96 Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. STEERING Your vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. Never hold the steering wheel to the extreme right or the extreme left for more than a few seconds when the engine is running.
Page 97 The height adjustment feature automatically controls the vehicle height over a range of approximately 5 cm (2 inches) based on vehicle speed, ignition position and selection of two or four-wheel drive modes. The air suspension shut-off switch is located behind an access panel underneath the passenger side instrument panel.
Page 98 Driving TRANSMISSION OPERATION Automatic transmission operation Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift from being moved from P (Park) unless the brake pedal is depressed. If you cannot move the gearshift out of P (Park) with the brake pedal depressed: 1.
Page 99 Hold the brake pedal down while you move the gearshift lever from position to position. If you do not hold the brake pedal down, your vehicle may move unexpectedly and injure someone. P (Park) Always come to a complete stop before shifting into P (Park).
Page 100 Driving (Overdrive) can be deactivated by pressing the Transmission Control Switch (TCS) on the end of the gearshift lever. The transmission control indicator light (TCIL) (the word OFF) on the end of the gearshift lever will illuminate. Drive – Not shown on the display. Activate by pressing the Transmission Control Switch (TCS) on the end of the gearshift lever with the gearshift in the position.
Page 101 1 (First) Use 1 (Low) to provide maximum engine braking on steep downgrades. Upshifts can be made by shifting to 2 (Second) or to (Overdrive). Selecting 1 (Low) at higher speeds causes the transmission to shift to a lower gear, and will shift to 1 (Low) after vehicle decelerates to the proper speed.
Page 102 Driving Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions. Avoid sharp turns or abrupt maneuvers in these vehicles.
Page 103 Shifting from 4H to 4L (and 4L to 4H) 1. Bring the vehicle to a stop. 2. Depress the brake. 3. Place the gearshift in N (Neutral). 4. Move the 4WD control to the 4H (or 4L) position. Shifting from A4WD to 4H Move the 4WD control from A4WD to 4H at any forward speed.
Page 104 Driving You should either know the terrain or examine maps of the area before driving. Map out your route before driving in the area. For more information on driving off-road, read the “Four Wheeling” supplement in your owner’s portfolio. If your vehicle gets stuck If the vehicle is stuck, shift the transmission in a steady motion between forward and reverse gears.
Page 105 Driving If the rear axle is submerged in water, the rear axle lubricant should be checked and changed, if necessary. The rear axle is filled with a synthetic lubricant and does not normally require a lubricant change for the life of the vehicle. Rear axle lubricant quantities should not need to be checked unless a leak is suspected.
Page 106 Driving Allow more stopping distance and drive slower than usual. Consider using one of the lower gears. DRIVING THROUGH WATER Do not drive quickly through standing water, especially if the depth is unknown. Traction or brake capability may be limited and if the ignition system gets wet, your engine may stall.
Page 107 Maximum Trailer Weight Rating: Maximum weight of a trailer the vehicle is permitted to tow. The maximum trailer weight rating equals the vehicle curb weight for each engine/transmission combination, any required option weight for trailer towing and the weight of the driver from the GCWR for the towing vehicle.
Page 108 Driving Follow these guidelines to ensure safe towing procedure: Stay within your vehicle’s load limits. Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter. Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter.
Page 109 Do not exceed the maximum loads listed on the Safety Compliance Certification label. For load specification terms found on the label, refer to Vehicle loading in this chapter. Remember to figure in the tongue load of your loaded trailer when figuring the total weight. Towing trailers beyond the maximum recommended gross trailer weight exceeds the limit of the vehicle and could result in engine damage, transmission damage, structural damage, loss of control...
Page 110 Driving trailer rental agency for proper instructions and equipment for hooking up trailer lamps. Driving while you tow Do not drive faster than 88 km/h (55 mph) when towing a trailer. Speed control may shut off if you are towing on long, steep grades. When towing a trailer: Use a lower gear when towing up or down steep hills.
Page 111 Launching or retrieving a boat When backing down a ramp during boat launching or retrieval, Do not allow the static water level to rise above the bottom edge of the rear bumper and Do not allow waves to break higher than 15 cm (six inches) above the bottom edge of the rear bumper.
Page 112: Roadside Emergencies
Roadside emergencies HAZARD LIGHTS CONTROL Use only in an emergency to warn traffic of vehicle breakdown, approaching danger, etc. The hazard flashers can be operated when the ignition is off. The hazard lights control is located on top of the steering column.
Page 113 The fuel pump shut-off switch is located in the passenger’s foot well, behind the kick panel. FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse.
Page 114 Roadside emergencies Standard fuse amperage rating and color Fuse rating 5 amp 7.5 amp 10 amp 15 amp 20 amp 20 amp fuse link 25 amp 30 amp 30 amp fuse link 40 amp fuse link 50 amp fuse link 60 amp fuse link 80 amp fuse link 100 amp fuse link...
Page 115 The fuses are coded as follows: Fuse/Relay Fuse Amp Location Rating 20A* 10A* 30A* 15A* 20A* 30A* 15A* 30A* Roadside emergencies Description Trailer Tow Running Lamp Relay, Trailer Tow Backup Lamp Relay Air Bag Diagnostic monitor All Unlock Relay, All Lock Relay, Driver’s Unlock Relay Air Suspension Service Switch Horn Relay...
Page 116 Roadside emergencies Fuse/Relay Fuse Amp Location Rating 15A* 25A* 25A* 10A* 30A** 60A** 50A** 40A** 30A** 30A** 20A** 50A** 50A** 50A** 40A** 30A** 30A CB 30A** 40A** 30A** 30A** * Mini Fuses ** Maxi Fuses Description Daytime running lamps (DRL) Module, Fog Lamp Relay I/P Auxiliary Power Socket Console Auxiliary Power Socket...
Page 117 Power distribution box The power distribution box is located in the engine compartment near the battery. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems from overloads. Always disconnect the battery before servicing high current fuses.
Page 118 Roadside emergencies Fuse/Relay Fuse Amp Location Rating Description Flasher Relay Instrument Cluster, Overhead Trip Computer (OTC) Module, Redundant Steering Control Module, Electronic Automatic Temperature Control (EATC) Module, Clock Cigar Lighter Park Lamp Relay, Headlamp Relay, Autolamp Module, Remote Anti-theft Personality (RAP) Module, Power Mirror Switch, Memory Seat and Mirror Module, Driver Power Seat Control Switch, Memory Seat Switch...
Page 119 Fuse/Relay Fuse Amp Location Rating — Roadside emergencies Description Shift Lock Actuator, Generic Electronic Module (GEM), 4 Wheel Air Suspension 4WAS Module, Compass Sensor, Steering Wheel Rotation Sensor, Heated Grid Relay, Overhead Trip Computer (OTC) Module Auxiliary A/C Relay, Console Blower Motor Radio, Main Light Switch, Remote Anti-theft Personality (RAP) Module, Generic Electronic Module (GEM), Ignition Switch,...
Page 120 Roadside emergencies Fuse/Relay Fuse Amp Location Rating — Description Instrument Cluster, Air Bag Diagnostic Monitor 4 Wheel Air Suspension 4WAS Generic Electronic Module (GEM), Memory Seat and Mirror Module Digital Transmission Range (DTR) Sensor, Junction Box Fuse/Relay Panel (Fuse 20) Air Bag Diagnostic Monitor, Ignition Switch Trailer Tow Battery Charge Relay, 4X4 Center Axle Disconnect Solenoid, 4X2 Center...
Page 121 Roadside emergencies Relays Relays are located in the power distribution box and should be replaced by qualified technicians. Primary battery fuses (megafuses) The primary battery fuses are located in the engine compartment near the battery.
Page 122 Roadside emergencies Ford recommends that the megafuses are serviced by a qualified service technician. Location Amperage Engine mini fuse box Description Power Network Box Megafuse Alternator Megafuse Alternator Field Minifuse...
Page 123 The engine mini fuses are located on the drivers side of the engine compartment. Slot Fuse Amperage Number Rating 5 amp 20 amp 10 amp 10 amp 20 amp CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed.
Page 124 Roadside emergencies 3. Un-snap the shaft of the handle from the two retaining clips attached to the top of the radiator shroud. Removing the jack and tools 1. Locate the access panel on the interior trim. Lift and rotate the two panel retaining clips and remove the panel.
Page 125 Tire change procedure On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to the instruction sheet (located behind the interior trim access panel with the jack) for detailed tire change instructions. 1.
Page 126 Roadside emergencies 6. Loosen each wheel lug nuts one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 7. Turn OFF the air suspension switch. 8. Position the jack according to the following guides and turn the jack handle clockwise until the wheel is completely off the ground.
Page 127 Roadside emergencies Front (4x2) Front (4x4)
Page 128 Roadside emergencies Rear Never use the front or rear differential as a jacking point. 9. Remove the lug nuts with the lug wrench. 10. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Page 129 12. Remove the jack and fully tighten the lug nuts in the order shown. 13. Stow the flat tire. Refer to Stowing the spare. 14. Stow the jack and lug wrench. Make sure the jack is fastened so it does not rattle when you drive. 15.
Page 130 Roadside emergencies 5. Turn the heater fan on in both vehicles to protect any electrical surges. Turn all other accessories off. Connecting the jumper cables 1. Position the vehicles so that they do not touch one another. 2. Switch off the engine. Switch off any unnecessary electrical equipment.
Page 131 Removing the jumper cables 1. Remove the jumper cables in reverse order. Take the cable off the metallic surface (1) first, followed by the cable on the negative (-) booster battery terminal (2). 2. Remove the cable from the positive ( +) terminal of the booster battery (3) and then the discharged battery (4).
Page 132 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground and the rear wheels off the ground.
Page 133: Maintenance And Care
SERVICE RECOMMENDATIONS To help you service your vehicle: We highlight do-it-yourself items in the engine compartment for easy location. We provide a “Service Guide” which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide necessary parts and service.
Page 134 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom left corner of the instrument panel.
Page 135 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L engine 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler 4. Engine oil dipstick 5. Power steering fluid reservoir 6. Brake fluid reservoir 7. Air filter assembly 8. Engine coolant recovery reservoir 9.
Page 136 Maintenance and care ENGINE OIL Checking the engine oil Check the engine oil each time you fuel your vehicle. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 137 If the oil level is below the MIN mark, add enough oil to raise the level within the MIN-MAX range. Oil levels above the MAX mark may cause engine damage. Some oil must be removed from the engine by a service technician. 7.
Page 138 Maintenance and care Engine oil recommendations Look for this certification mark. Ford oil specification is WSS-M2C153-G. Use SAE 5W-30 motor oil certified for gasoline engines by the American Petroleum Institute. Do not use supplemental engine oil additives, oil treatments or engine treatments.
Page 139 BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed at least once each year: 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir. 2. Visually inspect the fluid level. 3.
Page 140 Maintenance and care WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 141 coolant to the coolant reservoir. For more information on engine coolant maintenance, refer to Adding engine coolant in this chapter. Automotive fluids are not interchangeable; do not use engine coolant, antifreeze or windshield washer fluid outside of its specified function and vehicle location.
Page 142 The use of an improper coolant may void your warranty of your vehicle’s engine cooling system. Recycled engine coolant Ford Motor Company recommends that Ford and Lincoln-Mercury dealers use recycled engine coolant produced by Ford-approved processes. Not all coolant recycling processes produce coolant which meets Ford specification ESE-M97B44–A, and use of such coolant may...
Page 143 How fail-safe cooling works If the engine overheats, the engine will automatically switch from eight to alternating four cylinder operation. Each disabled cylinder acts as an air pump and cools the engine. When this occurs, the engine coolant temperature gauge will move into the red area and the light illuminates.
Page 144 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid at least twice a year. If adding fluid is necessary, use only MERCON ATF power steering fluid. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge will be near the center of the NORMAL band).
Page 145 Maintenance and care 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the range between the MIN and MAX lines. Be sure to put the cap back on the reservoir. TRANSMISSION FLUID Checking and adding automatic transmission fluid Follow the scheduled service intervals outlined in the “Service Guide.”...
Page 146 Maintenance and care The transmission fluid should be in this range if at room temperature (10°C-35°C [50°F-95°F]) (see figure to the right). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer, the vehicle should be turned off for about 30 minutes to allow the fluid to cool before checking.
Page 147 Maintenance and care DRIVELINE UNIVERSAL JOINT AND SLIP YOKE The universal joints standard with your vehicle do not require lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, lubrication will be necessary. BATTERY Your vehicle may be equipped with a Superstart maintenance-free battery.
Page 148 Maintenance and care relearn its idle conditions before your vehicle will drive properly. To begin this process: 1. Put the gearshift in P (Park), turn off all accessories and start the vehicle. 2. Let the engine idle for at least one minute. 3.
Page 149 Maintenance and care CHANGING THE AIR FILTER 1. Loosen the clamp that secures the air cleaner in place. 2. Separate the two halves of the air cleaner. 3. Remove the air filter element from the open end of the engine air cleaner and replace it with a new element.
Page 150 Maintenance and care 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin with a screwdriver to release the blade and pull the wiper blade down toward the windshield to remove it from the arm.
Page 151 Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire grade 150 would wear one and one-half (1 1/2) times as well on the government course as a tire grade 100.
Page 152 Maintenance and care SERVICING YOUR TIRES Checking the tire pressure Use an accurate tire pressure gauge. Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles).
Page 153 Replacing the tires Replace the tires when the wear band is visible through the tire treads. Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier to lose control and roll over. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 154 Maintenance and care If possible, avoid fully loading your vehicle. Remove the tire chains when they are no longer needed. Do not use tire chains on dry roads. The suspension insulation and bumpers will help prevent vehicle damage. Do not remove these components from your vehicle when using snow tires and chains.
Page 155 Observe the following guidelines when handling automotive fuel: Extinguish all smoking materials and any open flames before fueling your vehicle. Always turn off the vehicle before fueling. Automotive fuels can be harmful or fatal if swallowed. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent.
Page 156 Maintenance and care Octane recommendations Your vehicle is designed to use “Regular” unleaded with an (R+M)/ 2 octane rating of 87. We do not recommend gasolines labeled as “Regular” in high altitude areas that are sold with octane ratings of 86 or even less.
Page 157 Filling the fuel tank 1. Turn the engine off. After opening the fuel door, remove the cap carefully and slowly by turning it counterclockwise ¼ turn until it stops. Pull to remove the cap. A tether attaches the cap to the fuel filler pipe.
Page 158 Maintenance and care 3. After at least three to five fuel tank fill-ups, fill the fuel tank and record the current mileage reading. 4. Use one of the following equations to calculate fuel economy. Liters used x 100 Total miles traveled Keep a record for at least one month.
Page 159 If you smell exhaust fumes of any kind inside your vehicle, have the dealer inspect and fix your vehicle immediately. Do not drive if you smell exhaust fumes. These fumes are harmful and could kill you. Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent...
Page 160 Maintenance and care EXTERIOR BULBS Replacing exterior bulbs Check the operation of the following lamps frequently: headlamps foglamps high-mount brakelamp brakelamps turn signals license plate lamp tail lamps back-up lamps Do not remove lamp bulbs unless they can be replaced immediately with new ones.
Page 161 Maintenance and care 5. Rotate the headlamp bulb cover counterclockwise and remove. 6. Disconnect the electrical connector from the headlamp bulb by grasping the wire and pulling it rearward. 7. Remove the bulb retainer ring by turning it counterclockwise about ¼ turn, then slide the ring off the plastic base.
Page 162 Maintenance and care 8. Without turning, carefully pull the bulb assembly out of the headlamp assembly. 9. Insert the glass end of the new bulb into the socket. When the grooves in the plastic base are aligned, push the bulb into the socket until the plastic base contacts the rear of the socket.
Page 163 Maintenance and care 8. Insert the glass end of the new bulb into the parking lamp assembly socket. When the grooves in the plastic base are aligned, push the bulb into the socket until the plastic base contacts the rear of the socket. 9.
Page 164 Maintenance and care 2. Rotate the foglamp socket counterclockwise and remove. 3. Install the new bulb. 4. Connect the electrical connector to the back of the foglamp assembly. High-mount brakelamp For bulb replacement, see a dealer or qualified technician. Replacing tail lamp bulbs 1.
Page 165 Maintenance and care Replacing liftgate tail lamp bulb 1. Raise the liftgate and remove the lamp assembly nuts. 2. Carefully pull the lamp assembly outward to expose the electrical connector. 3. Remove the bulb assembly by turning counterclockwise. 4. Without turning, carefully pull out the bulb.
Page 166 Maintenance and care Replacing license plate lamp bulbs The license plate bulbs are located next to the liftgate handle. To change the license plate bulbs: 1. Remove the screw and the license plate cover to locate the bulb connector. 2. Twist the connector counterclockwise ¼ turn and carefully pull to remove it.
Page 167 AIMING THE HEADLAMPS Your vehicle is equipped with a Vehicle Headlamp Aim Device (VHAD) on each headlamp. Each headlamp may be properly aimed in the vertical (up/down) and the horizontal (left/right) directions using your VHAD system. The headlamps on your vehicle are properly aimed at the assembly plant, and vertical and horizontal indicators of the VHAD system are...
Page 168 Maintenance and care Horizontal aim adjustment 1. With the hood open, locate the horizontal indicator and adjusting screw. They are located below the viewing hole at the rear of the headlamp assembly. 2. Use a 4mm wrench or socket to turn the horizontal adjusting screw until the “0”...
Page 169 Maintenance and care 3. The “UP” and “DN” on the bubble indicate the directional change (up or down) of the vertical aim. 4. Use a 4 mm wrench or socket to turn the vertical adjusting screw clockwise or counterclockwise until the bubble is centered over the “0”...
Page 170 Maintenance and care Waxing your vehicle Wax when water stops beading on the surface. This could be every three or four months, depending on operating conditions. Use only carnauba or synthetic-based waxes. Remove any bugs and tar before waxing vehicle. Use cleaning fluid or alcohol with a clean cloth to remove.
Page 171 Cover the highlighted areas to prevent water damage when cleaning the engine. Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning plastic exterior parts Use vinyl cleaner for routine cleaning. Clean with a tar remover if necessary.
Page 172 Maintenance and care Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel. The dull finish in this area helps protect the driver from undesirable windshield reflection.
Page 173 In some instances, color or dye transfer can occur when wet clothing (wool, denim, leathers or other non-colorfast garments) comes in contact with leather upholstery. If this occurs, the leather should be cleaned immediately to avoid permanent staining. “Tanners Preserve Leather Cleaner” (product number AS-300) is available from “First Brands”...
Page 174: Capacities And Specifications
Capacities and specifications MOTORCRAFT PART NUMBERS Component Air filter Fuel filter Battery (standard) Battery (optional) Oil filter PCV Valve Spark plugs*-platinum * Replacement double platinum spark plug “EE” will replace “E” and “EG” and “P” will replace “P” and “PG” suffixed spark plugs. 5.4L engine FA-1632 FG-872...
Page 175 REFILL CAPACITIES Fluid Ford Part Name Brake fluid Ford High Performance DOT 3 Brake Fluid Engine oil Motorcraft 5W30 (includes filter Super Premium change) Motor Oil Power steering Motorcraft fluid MERCON ATF Transmission Motorcraft fluid MERCON ATF Transfer case Motorcraft fluid MERCON ATF Windshield...
Page 176 Capacities and specifications LUBRICANT SPECIFICATIONS Item Windshield washer fluid reservoir Body hinges, latches, door striker plates and rotors, seat tracks, fuel filler door hinge and spring, hood latch, auxiliary latch Lock cylinders Brake master cylinder Driveshaft, slip sline, double Cardan joint center ball Engine coolant Engine oil...
Page 177 Item 4x4 front wheel bearings, 4x4 spindle needle bearings, spindle thrust bearings & front drive axle u-joint/slip sline Automatic transmission Motorcraft Power steering reservoir Rear axle Front axle Transfer case - Four wheel drive Add 118 ml (4 oz.) of EST-M2C118–A (friction modifier Part No. C8AZ-19B546–A) for complete refill of Ford Traction-Lok rear axles.
Page 178 Capacities and specifications ENGINE DATA Engine Cubic inches Horsepower Torque Required fuel grade Firing order Spark plug gap Ignition system Compression ratio VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in.) (1) Overall length (2) Overall width (3) Overall height* (4) Wheelbase (5) Track - Front (5) Track - Rear * with 16 tire...
Page 179 Capacities and specifications...
Page 180: Vehicle Identification Number
Capacities and specifications IDENTIFYING YOUR VEHICLE Safety compliance label The National Highway Traffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the front door latch pillar on the driver’s side.
Page 181: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 182: Index
Index Air bag supplemental restraint system ...78 and child safety seats ...79 description ...78 disposal ...82 indicator light ...81 passenger air bag ...80 Air cleaner filter ...148,149 Air conditioning auxiliary heater and air conditioner ...29 Air suspension description ...96 warning light ...10 Ambulance packages ...3 Anti-lock brake system (ABS) description ...94...
Page 183 improving fuel economy ...111 octane rating ...156 quality ...156 safety information relating to automotive fuels ...154 Fuel gauge ...12 Fuel pump shut-off switch ...112 Fuse panels instrument panel ...114 power distribution box ...117,122 Fuses ...113,114,121 Gauges, Mechanical ...12 engine coolant temperature gauge ...13 Hazard flashers ...112 Head restraints ...62,65...
Page 184 Index Parts (see Motorcraft parts) ...174 Power door locks ...52 Power steering fluid, checking and adding ...144 Rear window wiper ...39 Refill capacities for fluids ...175 Relays ...113,121 Remote entry system ...57 illuminated entry ...59 locking/unlocking doors ...57,58 replacement/additional transmitters ...59 replacing the batteries ...58 Reporting safety defects ...181 Safety restraints...
Page 185 Vehicle headlamp aiming device (VHAD) ...167 Vehicle Identification Number (VIN) ...180 Vehicle loading ...106 Ventilating your vehicle ...92 Warning chimes ...6 Washer fluid rear window reservoir ...140 warning light ...11 Windows accessory delay ...51 power windows, operating ...45,50 Windshield washer fluid and wipers checking and adding fluid ...140 checking and...
Page 186: Filling Station Information
Filling station information Recommended fuel Fuel tank capacity Tire size and pressure Hood release Engine oil capacity (with filter change) Coolant capacity Power steering fluid capacity Automatic transmission fluid capacity-4x2 vehicles Automatic transmission fluid capacity-4x4 vehicles Ensure correct automatic transmission fluid is used for a specific application.

This manual is also suitable for:

1999 navigator

Lincoln 1998 Navigator Owner's Manual

Quick Links

Related Manuals for Lincoln 1998 Navigator

Summary of Contents for Lincoln 1998 Navigator

This manual is also suitable for:

Table of Contents