Page 1: Table Of Contents
2004 Cadillac SRX Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Rear Seats ... 1-7 Safety Belts ... 1-8 Child Restraints ... 1-28 Air Bag Systems ... 1-50 Restraint System Check ... 1-60 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, CADILLAC, the CADILLAC Crest & Wreath are registered trademarks and the name SRX is a trademark of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Page 3 Safety Warnings and Symbols You will ﬁnd a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this book you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 5 These are some examples of vehicle symbols you may ﬁnd on your vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ...1-2 Manual Passenger Seat ...1-2 Power Seats ...1-2 Power Lumbar ...1-3 Heated Seats ...1-3 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Rear Seats ...1-7 Rear Seat Operation ...1-7 Stowable Seat ...1-7 Safety Belts ...1-8 Safety Belts: They Are for Everyone ...1-8 Questions and Answers About Safety Belts ...1-13 How to Wear Safety Belts Properly ...1-14 Driver Position ...1-14...
Page 8: Front Seats
Front Seats Manual Passenger Seat Your vehicle may have a manual passenger seat. To adjust the seat, lift the bar under the front of the seat to unlock it. Slide the seat to where you want it and release the bar. Try to move the seat back and forth with your body to be sure the seat is locked in place.
Page 9 Power Lumbar Your vehicle may have this feature. The driver’s and passenger’s seatback lumbar support can be adjusted by moving a control located on the outboard side of the seat cushions. To increase or decrease support, hold the control forward or rearward. Keep in mind that as your seating position changes, as it may during long trips, so should the position of your lumbar support.
Page 10: Reclining Seatbacks
Reclining Seatbacks Manual Recliner If your vehicle has manual reclining front seatbacks, the levers are located on the outboard sides of the front seats. Lift the lever to release the seatback, then move the seatback to where you want it. Release the lever to lock the seatback in place.
Page 11 But don’t have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job.
Page 12 Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. The front seat head restraints move up and down. Press the button located at the bottom of the head restraint and raise or lower the head restraint.
Page 13: Rear Seats
Rear Seats Rear Seat Operation Adjusting the Second Row Seat The second row seat can be adjusted forward or rearward. Pull up on the lever under the seat cushion and slide the seat with your body. Release the lever and try to move the seat forward and rearward to be sure it is locked into place.
Page 14: Safety Belts
Two buttons are located inside the liftgate. One button is to tilt the seatback forward for added storage space or when storing a ﬂat tire. The other button is the power folding seat button. The button behind the second row seat is also a power folding seat button.
Page 15 CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 16: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it’s just a seat on wheels. 1-10...
Page 17 Get it up to speed. Then stop the vehicle. The rider doesn’t stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield... 1-11...
Page 18 or the instrument panel... 1-12 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense.
Page 19 Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could be – whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Page 20: How To Wear Safety Belts Properly
How to Wear Safety Belts Properly This part is only for people of adult size. Be aware that there are special things to know about safety belts and children. And there are different rules for smaller children and babies. If a child will be riding in your vehicle, see Older Children on page 1-28 or Infants and Young Children on page 1-31 .
Page 21 5. To make the lap part tight, pull up on the The lap part of the belt should be worn low and snug on shoulder belt. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt.
Page 22 What’s wrong with this? The shoulder belt is too loose. It won’t give nearly as much protection this way. 1-16 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body.
Page 23 What’s wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 24 What’s wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-18 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 25 What’s wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 26: Safety Belt Use During Pregnancy
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 27: Right Front Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 28: Rear Seat Passengers
Rear Seat Passengers Rear Seat Passenger Positions It is very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who are not safety belted can be thrown out of the vehicle in a crash.
Page 29 Lap-Shoulder Belt All rear seating positions have lap-shoulder belts. Here is how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Do not let it get twisted. 2. Push the latch plate into the buckle until it clicks. Pull up on the latch plate to make sure it is secure.
Page 30 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you would be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 31 Rear Safety Belt Comfort Guides for Children and Small Adults Your vehicle may have this feature. If not, you can get it from your dealer. Rear shoulder belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults.
Page 32 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top. 1-26 4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-22 . Make sure that the shoulder belt crosses the shoulder.
Page 33: Safety Belt Pretensioners
Safety Belt Pretensioners Your vehicle has safety belt pretensioners. You’ll ﬁnd them on the buckle end of the safety belts for the driver and right front passenger. They help the safety belts reduce a person’s forward movement in a moderate to severe crash in which the front of the vehicle hits something.
Page 34: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. 1-28 What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 35 CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-29...
Page 36 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck? If the child is sitting in a seat next to a window, move the child toward the center of the vehicle.
Page 37: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 38 CAUTION: People should never hold a baby in their arms while riding in a vehicle. A baby doesn’t weigh much -- until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 km/h), a 12-lb.
Page 39 CAUTION: Children who are up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants.
Page 40 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height, and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 41: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 42 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1-36 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 43 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window.
Page 44: Where To Put The Restraint
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may ﬁnd these instructions on the restraint itself or in a booklet, or both.
Page 45: Top Strap
CAUTION: (Continued) If you secure a forward-facing child restraint in the right front seat, always move the front passenger seat as far back as it will go. It is better to secure the child restraint in a rear seat outside position. Wherever you install it, be sure to secure the child restraint properly.
Page 46 In Canada, the law requires that forward-facing child restraints have a top strap, and that the strap be anchored. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored. 1-40 CAUTION: Each top tether bracket is designed to anchor...
Page 47: Top Strap Anchor Location
Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. Raise the head restraint and route the top strap under it.
Page 48 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You’ll ﬁnd anchors (A) for the second row outboard passenger positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors (A, B) and child restraint attachments to secure the restraints.
Page 49 In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each lower anchor position.
Page 50: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. 3.
Page 51 If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position. Be sure to follow the instructions that came with the child restraint. Secure the child in the child restraint when and as the instructions say.
Page 52 3. Buckle the belt. Make sure the release button is 4. Pull the rest of the shoulder belt all the way out of positioned so you would be able to unbuckle the the retractor to set the lock. safety belt quickly if you ever had to. 1-46...
Page 53: Securing A Child Restraint In The Right Front Seat Position
5. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 54 Your vehicle has a right front passenger air bag. Never put a rear facing child restraint in this seat. Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inﬂates.
Page 55 5. Pull the rest of the shoulder belt all the way out of the retractor to set the lock. 6. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 56: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has six air bags: • A frontal air bag for the driver and another frontal air bag for the right front passenger, • a seat mounted side impact air bag for the driver and another for the right front passenger, •...
Page 57 CAUTION: (Continued) The seat-mounted side impact air bags and roof-mounted side impact air bags are designed to inﬂate only in moderate to severe crashes where something hits the side of your vehicle. They aren’t designed to inﬂate in frontal, in rollover or in rear crashes. Everyone in your vehicle should wear a safety belt properly —...
Page 58: Where Are The Air Bags
There is a air bag readiness light on the instrument panel, which shows the air bag symbol. The system checks the air bag electrical system for malfunctions. The light tells you if there is an electrical problem. See Air Bag Readiness Light on page 3-40 for more information.
Page 59 The front passenger’s frontal air bag is in the instrument panel on the passenger’s side. The driver’s side impact air bag is in the side of the driver’s seatback closest to the door. 1-53...
Page 60 The right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door. 1-54 The roof-mounted side impact air bag for the driver and the passenger directly behind the driver is in the ceiling above the side windows.
Page 61 The roof-mounted side impact air bag for the front passenger and the passenger directly behind the front passenger is in the ceiling above the side windows. CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 62: When Should An Air Bag Inﬂate
When Should an Air Bag Inﬂate? The driver’s and right front passenger’s frontal air bags are designed to inﬂate in moderate to severe frontal or near-frontal crashes. But they are designed to inﬂate only if the impact speed is above the system’s designed “threshold level.”...
Page 63: What Makes An Air Bag Inﬂate
What Makes an Air Bag Inﬂate? In an impact of sufficient severity, the air bag sensing system detects that the vehicle is in a crash. For both frontal and side impact air bags, the sensing system triggers a release of gas from the inﬂator, which inﬂates the air bag.
Page 64: What Will You See After An Air Bag Inﬂates
What Will You See After an Air Bag Inﬂates? After the air bag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the air bag inﬂated. Some components of the air bag module – the steering wheel hub for the driver’s air bag, the instrument panel for the right front passenger’s bag, the side of the seatback closest to the door for the seat-mounted side...
Page 65 In many crashes severe enough to inﬂate the air bag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger air bag. • Air bags are designed to inﬂate only once. After an air bag inﬂates, you’ll need some new parts for your air bag system.
Page 66: Restraint System Check
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems.
Page 67: Replacing Restraint System Parts After A Crash
Torn or frayed safety belts may not protect you in a crash. They can rip apart under impact forces. If a belt is torn or frayed, get a new one right away. Also look for any opened or broken air bag covers, and have them repaired or replaced.
Page 68 NOTES 1-62...
Page 69: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-4 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-8 Door Locks ...2-8 Central Door Unlocking System ...2-9 Power Door Locks ...2-9 Delayed Locking ...2-9 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-10 Lockout Protection ...2-11 Leaving Your Vehicle ...2-11 Liftgate ...2-12...
Page 70 Section 2 Storage Areas ...2-45 Glove Box ...2-45 Cupholder(s) ...2-45 Cell Phone Storage Area ...2-45 Center Console Storage Area ...2-45 Map Pocket ...2-45 Assist Handles ...2-45 Garment Hooks ...2-45 Luggage Carrier ...2-46 Features and Controls Convenience Net ...2-47 Cargo Cover ...2-47 Cargo Management System ...2-47 Sunroof ...2-48 Sunroof (UltraView) ...2-48...
Page 71: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Do not leave the keys in a vehicle with children.
Page 72: Remote Keyless Entry System
Be sure you have spare keys. In an emergency, contact Cadillac Roadside Assistance. See Roadside Service on page 7-6 . If your vehicle is equipped with the OnStar system with...
Page 73: Remote Keyless Entry System Operation
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: •...
Page 74: Matching Transmitter(S) To Your Vehicle
If your vehicle is programmed for remote conﬁrmation, the doors must be closed for this feature to work. If a door is open, remote conﬁrmation will be canceled. (Unlock): Press this symbol on the remote keyless entry transmitter to unlock the driver’s door. This also disarms the theft-deterrent system.
Page 75: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about four years. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery.
Page 76: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 77 Central Door Unlocking System Your vehicle has a central door unlocking feature. When unlocking the driver’s door, you can unlock the other doors by holding the key in the turned position for a few seconds or by quickly turning the key twice in the lock cylinder.
Page 78: Programmable Automatic Door Locks
Programmable Automatic Door Locks Your vehicle is programmed so that when the doors are closed, the ignition is on and the shift lever is moved out of PARK (P), all the doors will lock. The doors will unlock every time you stop the vehicle and move the shift lever back into PARK (P).
Page 79: Lockout Protection
When you want to open a rear door when the security lock is on, do the following: 1. Unlock the door using the remote keyless entry transmitter, the front door power lock switch or by lifting the rear door manual lock. 2.
Page 80: Instrument Panel
Liftgate To unlock the liftgate from the outside, turn the key in the driver’s door cylinder counterclockwise or use the remote keyless entry transmitter. To lock the liftgate using the key, turn the key clockwise in the driver’s door. Open the liftgate using the handle located below the license plate.
Page 81: Windows
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 82: Express-Down Window
Power Windows The power window switches are located on the armrest near each window. Press the up or down arrows on the switches to raise or lower the windows. Your vehicle has Retained Accessory Power (RAP) that allows you to use the power windows once the ignition has been turned off for up to 10 minutes.
Page 83: Programming The Power Windows
Programming the Power Windows If the battery on your vehicle has been recharged, disconnected or is not working, you will need to reprogram each front power window for the express-up feature to work. Before reprogramming, you will need to replace or recharge your vehicle’s battery. To program each front window, follow these steps: 1.
Page 84: Window Lockout
Window Lockout This feature allows you to disable the passenger window switches. The passenger window lockout button is located below the power window switches on the driver’s door armrest. Press the button to disable the passenger window controls. The light on the button will illuminate, indicating that the feature is in use.
Page 85: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Theft-Deterrent System The security light is located on the instrument panel cluster.
Page 86: Testing The Alarm
Testing the Alarm 1. From inside the vehicle, roll down the window, then get out of the vehicle, keeping the door open. 2. From outside of the vehicle, with the door open, lock the vehicle using the power door lock switch or the remote keyless entry transmitter and close the door.
Page 87 Immobilizer Operation Your vehicle is equipped with a passive theft-deterrent system. The system works when you turn the key to ON. The key uses a transponder that matches an immobilizer control unit in your vehicle. The correct key will start the vehicle.
Page 88: Starting And Operating Your Vehicle
Your vehicle is not protected by the theft-deterrent system at this time. In an emergency, contact Cadillac Roadside Assistance. See Roadside Service on page 7-6 . 2-20 Starting and Operating Your...
Page 89: Ignition Positions
Ignition Positions With the key in the ignition switch, you can turn the key to four different positions. Notice: If your key seems stuck in OFF and you can’t turn it, be sure you are using the correct key; if so, is it all the way in? If it is, then turn the steering wheel left and right while you turn the key hard.
Page 90: Steering Column Ignition Lock Release
Steering Column Ignition Lock Release If your vehicle has a dead battery or a battery with low voltage, you can still release the ignition lock and remove the key. Use the following procedure to release the steering column: 1. Locate the plastic screw head on the underside of the plastic cover for the steering column.
Page 91: Starting Your Engine
Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N). Your engine won’t start in any other position – that’s a safety feature. To restart when you’re already moving, use NEUTRAL (N) only. Notice: Do not try to shift to PARK (P) if your vehicle is moving.
Page 92: Engine Coolant Heater
Engine Coolant Heater Your vehicle may be equipped with an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 93 How long should you keep the coolant heater plugged in? The answer depends on the outside temperature, the kind of oil you have, and some other things. Instead of trying to list everything here, we ask that you contact your dealer in the area where you’ll be parking your vehicle.
Page 94 If you cannot shift out of PARK (P), ease pressure on the shift lever. Push the shift lever all the way into PARK (P) while pressing the button on the shift lever as you maintain brake application. Then move the shift lever into the gear you wish.
Page 95: Shift Lock Release
AUTOMATIC OVERDRIVE (D): This position is for normal driving. If you need more power for passing, and you’re: • Going less than 35 mph (55 km/h), push the accelerator pedal about halfway down. • Going about 35 mph (55 km/h) or more, push the accelerator all the way down.
Page 96 Driver Shift Control (DSC) Your automatic transmission has a Driver Shift Control (DSC) feature that allows you to change gears similar to a manual transmission. To use the DCS feature: 1. Slide the shift lever over from AUTOMATIC OVERDRIVE (D) to the right DSC area. When the transmission is in DSC mode the sport mode light in the...
Page 97: Parking Brake
All-Wheel Drive If your vehicle is equipped with this feature, engine power is sent to all four wheels all the time. This is like four-wheel drive, but it is fully automatic. Parking Brake The parking brake pedal is located on the lower portion of the instrument panel to the left of the steering wheel.
Page 98: Leaving Your Vehicle With The Engine Running
Shifting Into Park (P) CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll. If you have left the engine running, the vehicle can move suddenly.
Page 99: Shifting Out Of Park (P)
If you have to leave your vehicle with the engine running, be sure your vehicle is in PARK (P) and your parking brake is ﬁrmly set before you leave it. After you’ve moved the shift lever into PARK (P), hold the regular brake pedal down.
Page 100: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-32 Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell.
Page 101: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 102: Mirrors
Mirrors Automatic Dimming Rearview Mirror ® with OnStar Your vehicle may have an automatic dimming inside rearview mirror. The mirror also contains OnStar controls. For more information about OnStar ® OnStar System on page 2-39 . (On/Off): This is the on/off button, located on the lower left side of the mirror, for the automatic dimming functions of the rearview mirror.
Page 103: Compass Calibration
Mirror Operation The automatic dimming feature is active each time the vehicle is started. To turn the automatic dimming feature on or off, press and release the on/off button. The indicator light will illuminate when this feature is active. Compass Operation Press the on/off button once to turn the compass on or off.
Page 104: Compass Variance
Compass Variance Compass variance is the difference between earth’s magnetic north and true geographic north. If the mirror is not adjusted for compass variance, your compass could give false readings. The mirror is set in zone eight upon leaving the factory. It will be necessary to adjust the compass to compensate for compass variance if you live outside zone eight.
Page 105: Climate Controls
Cleaning the Mirror When cleaning the mirror, use a paper towel or similar material dampened with glass cleaner. Do not spray glass cleaner directly on the mirror as that may cause the liquid cleaner to enter the mirror housing. Outside Power Heated Mirrors The control on the driver’s door armrest operates both outside rearview mirrors.
Page 106: Outside Automatic Dimming Mirror
Outside Automatic Dimming Mirror Your driver’s side mirror may have an automatic dimming feature. This helps to reduce glare from the headlamps of vehicles behind you. Outside Curb View Assist Mirror If your vehicle is equipped with the memory seat and mirrors, it will also be capable of performing the curb view assist mirror feature.
Page 107: Onstar System
® OnStar System ® OnStar uses global positioning system (GPS) satellite technology, wireless communications, and call centers to provide you with a wide range of safety, security, information and convenience services. ® A complete OnStar user’s guide and the terms and ®...
Page 108: Homelink Transmitter
Luxury and Leisure Plan • All Directions and Connections Plan services • Personal Concierge ® OnStar Personal Calling ® With OnStar Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts and no additional roaming charges.
Page 109 This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Page 110 Your vehicle’s engine should be turned off while programming the transmitter. Follow these steps to program up to three channels: 1. Press and hold down the two outside buttons, releasing only when the indicator light begins to ﬂash, after 20 seconds. Do not hold down the buttons for longer than 30 seconds and do not repeat this step to program a second and/or third transmitter to the remaining two HomeLink...
Page 111: Gate Operator And Canadian Programming
7. Firmly press and release the “Learn” or “Smart” button. The name and color of the button may vary by manufacturer. You will have 30 seconds to start Step 8. 8. Return to the vehicle. Firmly press and hold the ®...
Page 112: Using Homelink
® Using HomeLink Press and hold the appropriate HomeLink least half of a second. The indicator light will come on while the signal is being transmitted. ® Erasing HomeLink Buttons To erase programming from the three buttons do the following: 1.
Page 113: Storage Areas
Storage Areas Glove Box The glove box is located in front of the passenger’s seat on the instrument panel. To lock the glove box door, insert your key into the lock cylinder and turn it clockwise. Turn the key counterclockwise to unlock the door.
Page 114: Luggage Carrier
Luggage Carrier CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Page 115: Convenience Net
Convenience Net The convenience net attaches to the ﬂoor or back wall of the rear of the vehicle using six anchor points. The net can be used like a hammock across the rear of the vehicle or hooked on the ﬂoor. Put small loads, like grocery bags, behind the net.
Page 116: Sunroof
Sunroof Sunroof (UltraView) CAUTION: People who are in a crash and not wearing a safety belt properly can suffer much worse injuries. They can hit things inside the vehicle or be ejected from it, and be seriously injured or killed. This is true for any vehicle occupant, in any motor vehicle, but if you have the Ultraview roof it is, if anything, even more important.
Page 117 Anti-Pinch Feature If an object is in the path of the sunroof when it is closing, the anti-pinch feature will detect the object and stop the sunroof from closing at the point of the obstruction. The sunroof will then reverse. To close the sunroof once it has re-opened, remove the obstruction and press the front of the sunroof switch.
Page 118: Sunroof (Ultraview Plus)
Sunroof (UltraView Plus) CAUTION: People who are in a crash and not wearing a safety belt properly can suffer much worse injuries. They can hit things inside the vehicle or be ejected from it, and be seriously injured or killed. This is true for any vehicle occupant, in any motor vehicle, but if you have the Ultraview roof it is, if anything, even more important.
Page 119 Press the back of the front sunshade switch to open the front sunshade. Press the front of the switch to close the sunshade. The sunshade can not be closed further than the glass panel. The rear sunroof is a vent only roof. Press the rear of the switch to vent the roof.
Page 120: Vehicle Personalization
Vehicle Personalization Memory Seat and Mirrors If your vehicle has the memory feature, you can program and recall memory settings for the driver’s seating and outside rearview mirror driving positions for up to two drivers. The buttons for this feature are located on the driver’s door armrest.
Page 121 To stop recall movement of the memory feature at any time, press one of the power seat or mirror controls. Two personalized exit positions can also be programmed. Use the following steps to program exit positions: 1. Press memory seat button 1 or the button with the unlock symbol on the remote keyless entry transmitter with the number 1 on the back to recall the driving position.
Page 122 NOTES 2-54...
Page 123: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-7 Horn ...3-7 Tilt Wheel ...3-7 Turn Signal/Multifunction Lever ...3-8 Windshield Wiper Lever ...3-15 Cruise Control ...3-18 Exterior Lamps ...3-18 Interior Lamps ...3-21 Ultrasonic Rear Parking Assist (URPA) ...3-22 Accessory Power Outlets ...3-24 Ashtrays and Cigarette Lighter ...3-25 Climate Controls ...3-26...
Page 124 Section 3 Audio System(s) ...3-94 Setting the Time ...3-94 Radio with CD ...3-95 Navigation/Radio System ...3-111 Rear Seat Entertainment System ...3-112 Theft-Deterrent Feature ...3-124 Audio Steering Wheel Controls ...3-124 DVD Distortion ...3-126 Instrument Panel Understanding Radio Reception ...3-126 Care of Your CDs and DVDs ...3-127 Care of Your CD and DVD Player ...3-127 Cleaning Your DVD Player ...3-127 Cleaning the Video Screen ...3-127...
Page 125 NOTES...
Page 126: Instrument Panel Overview
Instrument Panel Overview...
Page 127 The main components of the instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-32 . B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8 . C. Steering Wheel Controls. See Audio Steering Wheel Controls on page 3-124 .
Page 128: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning button is located in the center of the instrument panel, between the two air vents.
Page 129: Other Warning Devices
Other Warning Devices If you carry reﬂective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn Press on the pad near the horn symbols on the steering wheel to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive.
Page 130: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals • Headlamps • Headlamp High/Low Beam-Changer • Flash-To-Pass Feature • Fog Lamps • Cruise Control For more information on the exterior lamps, see Exterior Lamps on page 3-18 .
Page 131: Driver Information Center (Dic)
Turn Signal On Chime If the turn signal is left on for about 1 mile (1.6 km), a warning chime will sound and the Turn Signal On message will appear on the Driver Information Center (DIC) display. See “Turn Signal On Message” under DIC Warnings and Messages on page 3-65 for more information.
Page 132 Headlamps The exterior lamp control is located in the middle of the turn signal/multifunction lever. (Exterior Lamp Control): Turn the control with this symbol on it to operate the exterior lamps. The exterior lamp control has four positions: (On/Off): Turn the control to this position to turn off all lamps except the Daytime Running Lamps (DRL).
Page 133: Fog Lamps
Wiper-Activated Headlamps This feature activates the headlamps and parking lamps after the windshield wipers have been in use for about six seconds. For this feature to work, the exterior lamp control must be in AUTO. When the exterior lamp control is off or in the parking lamp position and the windshield wiper control is in any position except off, the Headlamps Suggested message will appear on the DIC display.
Page 134: Cruise Control
Cruise Control These controls are located on the end of the multifunction lever. (Off): This position turns the system off. (On): This position activates the system. + (Resume/Accelerate): Push the lever to this symbol to make the vehicle resume to a previously set speed or to accelerate when cruise is already active.
Page 135 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 136 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press the set button at the end of the lever, then release the button and the accelerator pedal.
Page 137: Windshield Wiper Lever
Windshield Wiper Lever Windshield Wipers The lever on the right side of the steering column operates the windshield wipers. (Mist): Pull the lever down and release it for a single wiping cycle. The lever will return to its original position. For more cycles, hold the lever down before releasing it.
Page 138: Windshield Washer
(Low Speed): Put the lever in this position for slow, steady wiping cycles. (High Speed): Put the lever in this position for rapid wiping cycles. If the windshield wipers are in use for about six seconds while you are driving, the exterior lamps will come on automatically if the exterior lamp control is in AUTO.
Page 139: Rear Washer/Wiper
If your vehicle is low on washer ﬂuid, the Check Washer Fluid message will appear on the Driver Information Center (DIC) display. See DIC Warnings and Messages on page 3-65 for more information. If the headlamps are on when you wash the windshield, the headlamp washers (if equipped) will turn on.
Page 140: Exterior Lamps
The headlamps must be on in order to be washed. If the headlamps are off, only the windshield will be washed when the washer button is pressed. To wash the headlamps, press the washer button located at the end of the windshield wiper lever. Both the headlamps and the windshield will be washed.
Page 141 When DRL are on, only your front turn signal lamps will be on. No other exterior lamps will be on when the DRL are being used. Your instrument panel won’t be lit up either. When the exterior lamp control is in AUTO and it’s dark enough outside, the DRL will turn off and the low-beam headlamps will turn on.
Page 142: Light Sensor
Light Sensor The light sensor for the DRL and AUTO headlamp feature is located on top of the instrument panel. If you cover the sensor, it will read dark, and the exterior lamps or the Headlamps Suggested message will appear on the DIC whenever the ignition is on. 3-20 Exterior Lighting Battery Saver If the parking lamps or headlamps have been left on,...
Page 143: Interior Lamps
Interior Lamps Instrument Panel Brightness The lever for this feature is located on the overhead console. Slide the lever toward the symbol to brighten the lights or away from it to dim them. If you slide the lever all the way toward the symbol past the resistance point, the interior lamps will come on.
Page 144: Reading Lamps
Reading Lamps The reading lamps are located on the overhead console. These lamps come on automatically when any door is opened. For manual operation, press the button next to each lamp to turn it on. Press it again to turn the lamp off. If the reading lamps are left on, they automatically shut off 10 minutes after the ignition has been turned off.
Page 145: How The System Works
The URPA display is located inside the vehicle, above the liftgate glass. It has three color-coded lights that can be seen through the rearview mirror or by turning around. How the System Works URPA comes on automatically when the shift lever is moved into REVERSE (R) and the vehicle speed is less than 3 mph (5 km/h).
Page 146: Accessory Power Outlets
When the System Does Not Seem to Work Properly The light may ﬂash red when the vehicle is in REVERSE (R) if the ultrasonic sensors are not kept clean. So be sure to keep your rear bumper free of mud, dirt, snow, ice and slush.
Page 147: Ashtrays And Cigarette Lighter
Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain accessory power plugs may not be compatible to the accessory power outlet and could result in blown vehicle or adapter fuses.
Page 148: Cigarette Lighter
Cigarette Lighter Notice: Holding a cigarette lighter in while it is heating will not allow the lighter to back away from the heating element when it is hot. Damage from overheating may occur to the lighter or heating element, or a fuse could be blown. Do not hold a cigarette lighter in while it is heating.
Page 149: Automatic Operation
Automatic Operation AUTO (Automatic): When this button is pressed and the temperature is set, the system will automatically control the inside temperature, the air delivery mode, the air conditioning compressor and the fan speed. AUTO will appear on the display. 1.
Page 150 Manual Operation yN z (Mode): Pressing the MODE switch and changing the mode cancels automatic operation and places the system in manual mode. Press AUTO to return to automatic operation. The outboard air outlets will always receive airﬂow regardless of the mode selected. See Outlet Adjustment on page 3-32 to change this airﬂow from the outboard outlets.
Page 151 (Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or to help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off.
Page 152 Sensors There is a solar sensor located on the instrument panel, near the windshield. 3-30 There is also an interior temperature sensor located to the right of the steering wheel on the instrument panel. These sensors monitor the solar radiation and the air inside your vehicle, then use the information to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed and the...
Page 153: Defogging And Defrosting
Defogging and Defrosting Fog on the inside of windows is a result of high humidity (moisture) condensing on the cool window glass. This can be minimized if the climate control system is used properly. There are two modes to clear fog from your windshield.
Page 154: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog or frost from the rear window. The rear window defogger will only work when the ignition is in ON. (Rear Window Defogger): Press this button to turn the rear window defogger on or off.
Page 155: Operation Tips
(Side Window Defog): Turn the thumbwheel to this symbol to use the side window defog setting. The air coming through the outlets will be directed toward the side windows to clear fog. (Open): Turn the thumbwheel to this symbol to open the outlets completely and allow the maximum amount of air to enter your vehicle.
Page 156: Rear Air Conditioning System
Rear Air Conditioning System If your vehicle has the rear air conditioning system it has two fan speed selectors. One fan speed selector is located in the front overhead console and the other is located in the headliner above the second row seats. The rear air conditioning system is designed to provide cooled air only.
Page 157: Passenger Compartment Air Filter
Passenger Compartment Air Filter The passenger compartment air ﬁlter traps most of the pollen from the air entering your vehicle. Like your vehicle’s engine air cleaner/ﬁlter, it needs to be changed periodically. For how often to change the passenger compartment air ﬁlter, see Scheduled Maintenance on page 6-4 .
Page 158 Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 159: Instrument Panel Cluster
Instrument Panel Cluster The instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using and many of the other things you’ll need to know to drive safely and economically.
Page 160: Speedometer And Odometer
Speedometer and Odometer The speedometer lets you see your speed in either miles per hour (mph) or kilometers per hour (km/h). The odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). You may wonder what happens if a vehicle has to have a new odometer installed.
Page 161: Tachometer
You can reset the selected trip odometer by pressing CLR (Clear) button located in the center of the INFO button to the right of the screen. The mileage for that trip odometer will return to zero. Each trip odometer must be reset individually. Using the Navigation audio system, do the following: 1.
Page 162: Engine Speed Limiter
Engine Speed Limiter This feature prevents the engine from operating at too many revolutions per minute (rpm). When the engine’s rpm are too high, the throttle is closed to reduce speed, if this is not sufficient, then the fuel supply to the engine will be limited.
Page 163: Charging System Light
CAUTION: If the air bag readiness light stays on after you start your vehicle, it means the air bag system may not be working properly. The air bags in your vehicle may not inﬂate in a crash, or they could even inﬂate without a crash. To help avoid injury to yourself or others, have your vehicle serviced right away if the air bag readiness light stays on after you start your...
Page 164: Brake System Warning Light
Brake System Warning Light Your vehicle’s hydraulic brake system is divided into two parts. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. Have your brake system inspected right away.
Page 165: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light With the anti-lock brake system, the light will come on when your engine is started and may stay on for several seconds. That’s normal. If the ABS warning light comes on and stays on, there may be a problem with the antilock portion of the brake system.
Page 166: Traction Control System (Tcs)
Traction Control System (TCS) Warning Light If the TC (traction control) warning light comes on and stays on, there may be a problem with the traction control system. The TC (traction control) warning light will come on brieﬂy when you turn the ignition to ON. If it doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem.
Page 167: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the gage pointer moves into the shaded area, the engine is too hot. That reading means the same thing as the warning light – the engine coolant is very hot. See Engine Overheating on page 5-27 .
Page 168: Malfunction Indicator Lamp
Malfunction Indicator Lamp Check Engine Light Your vehicle is equipped with a computer which monitors operation of the fuel, ignition and emission control systems. This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment.
Page 169: If The Light Is Flashing
If the Light is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed. • Avoiding hard accelerations. • Avoiding steep uphill grades. • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady”...
Page 170: Maintenance Schedule
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the Check Engine light is on or not working properly.
Page 171: Sport Mode Light
This light tells you if there could be a problem with your engine oil pressure. The light goes on when you turn your key to ON or START. It goes off once you start your engine. That’s a check to be sure the light works. If it doesn’t come on, be sure to have it ﬁxed so it will be there to warn you if something goes wrong.
Page 172: Fog Lamp Light
Fog Lamp Light This light will come on when the fog lamps are in use. The light will go out when the fog lamps are turned off. See “Fog Lamps” under Turn Signal/Multifunction Lever on page 3-8 for more information. Lights On Reminder This light comes on whenever the parking...
Page 173: Fuel Gage
Fuel Gage The fuel gage shows approximately how much fuel is in the tank. It works only when the ignition is in ON. If the fuel supply gets low, the Fuel Level Low message will appear on the DIC and a single chime will sound. Here are a few concerns some owners have had about the fuel gage.
Page 174: Driver Information Center (Dic)
Driver Information Center (DIC) The DIC gives you the status of many of your vehicle’s systems. It is also used to display driver personalization features and warning/status messages. All messages will appear on the audio system display which is also the display for the Navigation system.
Page 175: Status Of Vehicle Systems
Navigation/Audio System If you have the Navigation system, use the following to operate the DIC. Brieﬂy press the blue vehicle information button in the upper right corner of the screen. Each press of this button will scroll to the next available vehicle information item. The Vehicle Information menu allows you to select the vehicle information to be displayed and allows you to reset or turn on or off certain information.
Page 176: Vehicle Information Menu
Vehicle Information Menu (Base Audio System) To access this menu using the Base audio system, press the up or down arrow on the INFO switch located to the right of the display. The following items are available when the ignition is in RUN.
Page 177: Navigation System
Vehicle Information Menu (Navigation System) To access the Vehicle Info menu using the Navigation system, press and hold the vehicle information button in the upper right corner of the screen for three seconds. You can also access this menu through the Main Audio menu.
Page 178: Vehicle Information Menu Item Descriptions
Vehicle Information Menu Item Descriptions The following paragraphs contain a more detailed description of each menu item: Clock/Outside Air Temp (Navigation System): If you select this item, the clock and outside temperature will be displayed at the top of the screen. The outside temperature will be displayed in either degrees Fahrenheit or degrees Celsius depending upon whether the system is set for English or metric units.
Page 179 GAL FUEL USED/Fuel Used: If you select this item, the number of gallons or liters of fuel used since the last reset of this menu item is displayed. To reset GAL FUEL USED using the Base audio system, press the CLR button located to the right of the screen.
Page 180 TIMER/Timer: If you select this item, a timing feature is displayed. The timer functions like a stopwatch in that you can record the time it takes to travel from one point to another. To turn on the timer using the Base audio system, press the CLR button located to the right of the screen once.
Page 181 LF TIRE/Left Front Tire Pressure: If you select this item, the air pressure in the driver’s side front tire will be displayed. If the tire pressure is normal, OK will be displayed with this item. If the tire pressure is low, LOW will be displayed with this item.
Page 182 ENGINE OIL LIFE/Engine Oil Life: If you select this item, the percentage of remaining oil life is displayed. If you see 99% Oil Life on the display, that means that 99% of the current oil life remains. When the oil life is depleted, the Change Engine Oil message will appear on the display.
Page 183: Dic Main Menu
DIC Main Menu Accessing the DIC Main Menu (Base Audio System) There are two different procedures for accessing the DIC main menu depending upon whether or not your vehicle has the Navigation system. To access the main menu of the DIC, do one of the following: •...
Page 184: Audio System(S)
DIC Main Menu Item Descriptions (Base Audio System) The following descriptions are for the Base audio system. For information pertaining to the Navigation audio system, see “ Audio System” in the Index of the SRX Entertainment and Navigation System Supplement supplied with your vehicle.
Page 185 CAT (Category): This menu item allows you to select radio stations based on preset categories. To turn the CAT feature on, press the TUNE/SEL knob once. When CAT is on, an X will be in the box next to CAT on the menu.
Page 186 (English/Metric Units): Use this menu item to adjust the measurement units. You can choose between ENGLISH UNITS and METRIC UNITS. To switch between the two, press the TUNE/SEL knob. Once your choice is displayed, turn the knob to set your choice and continue scrolling through the main menu.
Page 187: Dic Warnings And Messages
DIC Warnings and Messages These messages will appear if there is a problem sensed in one of your vehicle’s systems. The text messages are the same for both the Base audio and Navigation systems unless otherwise indicated. You must acknowledge a message to clear it from the screen for further use.
Page 188: Battery Voltage Low
Battery Voltage Low This message will appear when the electrical system is charging less than 10 volts or if the battery has been drained. If this message appears immediately after starting the engine, it is possible that the generator can still recharge the battery.
Page 189: Change Trans (Transmission) Fluid
Change Trans (Transmission) Fluid This message indicates that the life of the transmission ﬂuid has expired and it should be changed within 200 miles. See Scheduled Maintenance on page 6-4 and Recommended Fluids and Lubricants on page 6-11 for the proper ﬂuid and change intervals. When you reset the Change Trans Fluid message by clearing it from the display, you still must reset the transmission ﬂuid life monitor separately.
Page 190: Engine Coolant Hot – Idle Engine
Engine Coolant Hot – Idle Engine This message will appear when the engine coolant temperature is too hot. Stop and allow the vehicle to idle until it cools down. Notice: If you drive your vehicle while the engine is overheating, severe engine damage may occur. If an overheat warning appears on the instrument panel cluster and/or DIC, stop the vehicle as soon as possible.
Page 191: Oil Pressure Low – Stop Engine
Headlamps Suggested This message will appear when the amount of available light outside the vehicle is low and the exterior lamp control is off. This message informs the driver that turning on the exterior lamps is recommended even though the DRL are still illuminated and it has become dark enough outside to require the headlamps and/or other exterior lamps.
Page 192: Service Charging System
Right Rear Door Ajar When this message appears on the display, the right rear door it means that the passenger’s side rear door was not closed completely. You should check to make sure that the door is closed completely. Service AC (Air Conditioning) System This message appears when the electronic sensors that control the air conditioning and heating systems are no longer working.
Page 193: Service Stability System Message
Service Stability System Message Your vehicle is equipped with a vehicle stability enhancement system called Stabilitrak ® See Stabilitrak System on page 4-10 . The Service Stability System message will be displayed if there has been a problem detected with Stabilitrak If the Service Stability System message comes on while you are driving, pull off the road as soon as possible and stop carefully.
Page 194: Service Suspension System
Service Suspension System This message is displayed to indicate that the suspension system is not operating properly. Have your vehicle serviced at your dealership. Service Theft System This message means there is a problem with the Immobilizer. See Immobilizer on page 2-18 for more information.
Page 195: Top Speed – Fuel Cut Off
Top Speed – Fuel Cut Off This message will appear when the Engine Control Module (ECM) detects that the maximum speed for your vehicle has been reached. Your vehicle’s top speed is based on the top speed rating of the tires. This ensures that your vehicle stays in a safe operating range for the tires.
Page 196: Dic Vehicle Personalization
DIC Vehicle Personalization Your vehicle is equipped with personalization that allows you to program certain features to a preferred setting for up to two people. The number of programmable features varies depending upon which model of the vehicle is purchased. On all vehicles, features such as climate control settings, radio preset settings, exterior lighting at unlock, remote lock and unlock conﬁrmation, and automatic...
Page 197: Personalization Features
Navigation System 1. Turn the ignition to ON without the engine running. Make the vehicle is in PARK (P). 2. If your vehicle has memory settings, press the appropriate memory button, 1 or 2, located on the driver’s door armrest. The DIC display will show either Driver 1 or 2 depending on which button was selected.
Page 198 3. Turn the TUNE/SEL knob until you reach the ﬁrst letter you want; the letter will be highlighted. There is a complete alphabet with both upper and lower case letters and the numbers zero through nine. Also included are spaces and other non-letter characters such as the ampersand (&).
Page 199 Remote Recall Memory/Recall Driving Positions If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat, adjustable pedals and mirror controls when the unlock button on the remote keyless entry transmitter is pressed.
Page 200 Remote Exit Recall If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver’s seat when the unlock button on the remote keyless entry transmitter is pressed.
Page 201 Key in Recall Memory If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed seat and mirror positions when the key is inserted into the ignition. Programmable Modes Mode 1: ON Mode 2: OFF...
Page 202: Auto Exit Seat
Auto Exit Seat If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, you can recall any previously programmed exit position for the driver’s seat when the key is removed from the ignition and the driver’s door is opened.
Page 203 Twilight Delay This feature allows you to set the amount of time you want the exterior lamps to remain on after you exit the vehicle. Programmable Modes Mode 1: 0:00 seconds Mode 2: 0:15 seconds Mode 3: 0:30 seconds Mode 4: 1:00 minute Mode 5: 1:30 minutes Mode 6: 2:00 minutes Mode 7: 2:30 minutes...
Page 204 Lights Flash at Unlock This feature turns on the exterior lamps when the remote keyless entry transmitter is used to unlock the vehicle. The lamps will remain on for approximately 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON or START or the remote keyless entry transmitter is used to lock the vehicle.
Page 205 Lights Flash at Lock This feature allows the exterior lamps to ﬂash once when the remote keyless entry transmitter is used to lock the vehicle. All doors must be closed for this feature to work, and the lamps will not ﬂash if the parking lamps or headlamps are on.
Page 206: Horn Sounds At Lock
Horn Sounds at Lock This feature sounds the horn once when the remote keyless entry transmitter is used to lock the vehicle. All doors must be closed for this feature to work. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2.
Page 207: Exterior Lights At Unlock
Exterior Lights at Unlock This feature turns on the exterior lamps when the remote keyless entry transmitter is used to unlock the vehicle. The lamps will remain on for about 20 seconds unless a door is opened, the ignition is turned to ACCESSORY, ON or START or the remote keyless entry transmitter is used to lock the vehicle.
Page 208 Driver Unlock in Park The feature allows the driver’s door to automatically unlock when the transmission is shifted into PARK (P). Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 209 Driver Unlock Key Out This feature allows the driver’s door to automatically unlock when the key is removed from the ignition. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 210 Doors Unlock in Park The feature allows the doors to automatically unlock when the transmission is shifted into PARK (P). Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 211 Doors Unlock Key Out This feature allows the doors to automatically unlock when the key is removed from the ignition. Programmable Modes Mode 1: ON Mode 2: OFF Before your vehicle was shipped from the factory, it was programmed to Mode 2. The mode to which the vehicle was programmed may have been changed since it left the factory.
Page 212: Delayed Locking
Delayed Locking This feature delays the locking of the vehicle’s doors for up to ﬁve seconds after a power door lock switch or the lock button on the remote keyless entry transmitter is pressed. The ﬁve second delay occurs after the last door is closed.
Page 213 Lock Passenger Window This feature allows you to disable either all the passenger window switches or the rear passenger window switches only. If this feature is turned on, all passenger window switches will be disabled when the window lockout button is pressed.
Page 214 Mirror to Curb in Reverse If your vehicle has the optional memory package, you will have this feature. When this feature is turned on, the passenger’s outside rearview mirror will move downward so you can view the curb when the shift lever is shifted into REVERSE (R).
Page 215: Exiting The Personalization Menu
Enhanced Chime Volume This feature allows you to adjust the volume level of the vehicle’s warning chimes. The chime volume cannot be turned off, only adjusted. Programmable Modes Mode 1: NORMAL Mode 2: LOUD Before your vehicle was shipped from the factory, it was programmed to Mode 1.
Page 216: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle – like a tape player, CB radio, mobile telephone or two-way radio – be sure you can add what you want. If you can, it’s very important to do it properly.
Page 217: Radio With Cd
Radio with CD Single CD Player Audio System Shown – Six-CD CD Player Similar Radio Data System (RDS) Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, your radio can do the following: •...
Page 218: Playing The Radio
XM™ Satellite Radio Service (48 Contiguous US States) XM™ is a continental U.S. based satellite radio service that offers 100 coast to coast channels including music, news, sports, talk, and children’s programming. XM™ provides digital quality audio and text information, including song title and artist name.
Page 219: Finding A Station
Finding a Station BAND: Press this button to select FM1, FM2, or AM, or XM1 or XM2 (48 contiguous US states, if equipped). SEEK : Press the up or the down arrow to seek to the next or to the previous station and stay there. SEEK will appear on the display.
Page 220: Setting Preset Stations
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 30 stations (six FM1, six FM2, and six AM, six XM1 and six XM2 (48 contiguous US states, if equipped), by performing the following steps: To set your preset stations manually, perform the following steps:...
Page 221: Setting The Tone (Bass/Treble)
PRESETS HOME/AWAY: This feature gives you the ability to store two different kinds of station presets. HOME can be used for stations available where you live and AWAY can be for stations available outside of your local broadcasting area. To set preset stations for home and away perform the following steps: 1.
Page 222: Using Dsp
Adjusting the Speakers (Balance/Fade) To adjust the balance or fade, perform the following steps: 1. Press the TUNE/SEL knob to enter the main menu. 2. Turn the TUNE/SEL knob until BASS-MID-TREBLE appears on the display. 3. Press the TUNE/SEL knob to enter into the tone settings.
Page 223: Rds Messages
DSP NORMAL: This setting provides the best overall audio performance for all passengers. DSP NORMAL will not be displayed when in this mode. TALK: This setting should be used when listening to non-musical material such as news, talk shows, sports broadcasts, and books on tape. Talk makes spoken words sound very clear.
Page 224 If you would like to display the message, perform the following steps: 1. Press the TUNE/SEL knob to enter the main menu. 2. Turn the TUNE/SEL knob until RECALL RDS MESSAGE appears on the display. 3. Press the TUNE/SEL knob. The message will appear on the display.
Page 225: Radio Message
Activating Program Type (PTY) Stations (RDS and XM™) PTY allows you to search for stations with speciﬁc types of music. The selectable PTYs are POP, EASY, TALK, CNTRY (Country), CLASS (Classical), and JAZZ. To activate program types, perform the following steps: 1.
Page 226 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. XM Updating Updating encryption code No XM Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) Channel Off Air Channel not in service Channel Unavail...
Page 227 Radio Display Message No CAT Info Category Name not available Not Found No channel available for the chosen category No Information No Text/Informational message available XM Lock Theft lock active XM Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Check XM Receiver...
Page 228: Using The Single Cd Player
Using the Single CD Player Insert a CD partway into the slot, label side up. The player will pull it in. If the ignition and the radio are on the CD will begin playing. CD will appear on the display. A CD may be loaded with the radio off but it will not start playing until the radio is on.
Page 229: Using The Six-Cd Cd Changer
F6 DISP (Display): Press this pushbutton to display the time of the track. Press this pushbutton again to remove the time of the track from the display. SEEK : Press the up or the down arrow to seek to the next or to the previous track on the CD. SCAN: Press this button to listen to each track for 10 seconds.
Page 230 When a CD is inserted, CD will appear on the display, the number of the CD and the track number will appear on the display if the radio is on. If the radio is on, the CD will begin to play automatically. To insert multiple CDs, do the following: 1.
Page 231 • RPT TRCK (Repeat Track): Repeats the track over again. RPT TRCK will appear on the display. Press the MODE pushbutton again to turn off repeat play. RPT TRCK will disappear from the display. • RPT CD (Repeat CD): Repeats the CD over again. RPT DISC will appear on the display.
Page 232: Cd Messages
CD Messages If the CD comes out, it could be for one of the following reasons: • If it is very hot. When the temperature returns to normal, the CD should play. • If you are driving on a very rough road. When the road becomes smooth the CD should play.
Page 233: Navigation/Radio System
7. Press the TUNE/SEL knob to select the conﬁgurable key to change. 8. Turn the TUNE/SEL knob to ﬁnd the feature that you would like to store to the key. 9. Press the TUNE/SEL knob when you have found the feature to be stored. The display will update, by showing the symbol of the feature that you selected next to the conﬁgurable key.
Page 234: Rear Seat Entertainment System
Rear Seat Entertainment System Your vehicle may have the optional Digital Versatile Disc (DVD) Rear Seat Entertainment (RSE) system. The RSE system includes a DVD player, a video display screen, two sets of wireless headphones, and a remote control. RSE is available in a base and an uplevel version. The uplevel version is provided with the Navigation radio (if equipped).
Page 235 DVD Player Buttons (Power): Press this button to turn the RSE system on or off. (Eject): Press this button to eject a DVD or a CD. SRCE (Source): Press this button to cycle through the available video modes. Auxiliary is available when something is plugged into the available auxiliary jacks on the DVD faceplate.
Page 236: Playing A Disc
(Menu): Press this button to access the DVD menu. This button only operates with a DVD. If your vehicle is equipped with the TV option, the menu button will bring up a TV speciﬁc menu. (Display Menu): Press this button to modify the video screen display characteristics.
Page 237: Ejecting A Disc
Some DVDs will not allow you to fast forward or skip the copyright or previews. Some DVDs will begin playing after the previews have ﬁnished. If the DVD does not begin to play the main title, refer to the on-screen instructions, as the DVD may be displaying its main title menu.
Page 238: Remote Control
Parental Control Button: This button is located on the navigation system screen. Press this button while a DVD or CD is playing to freeze the video and mute the audio. The video screen will display Parental Control ON and the power indicator light on the DVD player will ﬂash.
Page 239: Remote Control Buttons
Remote Control Buttons (Power): Press this button to turn the DVD player on or off. (Illumination): Press this button to turn the remote control backlight on for 8 seconds. (Title): Press this button to access the multiple titles (if available) of a DVD. (Menu): Press this button to access the DVD main menu.
Page 240 (Right): Press this button to move to the right of the menu list of a DVD. (Enter): Press this button to select items within a menu. (Audio): Press this button to open a menu that will operate only when a DVD is being played. The format and content of this function is deﬁned by the disc and is dependent on the disc.
Page 241 Battery Replacement To change the batteries, do the following: 1. Remove the battery compartment door located on the bottom of the remote control. 2. Replace the two AA batteries in the compartment. Make sure that they are installed correctly. 3. Close the battery door securely. Notice: Do not store the remote control in heat or direct sunlight.
Page 242: Stereo Rca Jacks
Battery Replacement To change the batteries, do the following: 1. Loosen the screw on the battery compartment door located on the left side of the headphone earpiece. 2. Replace the two AAA batteries in the compartment. Make sure that they are installed correctly. 3.
Page 243: Audio Output
How to Change the Video Format when in the Auxiliary Mode The auxiliary input video format is preset to NTSC. In some countries, the video format may be in PAL system. To change the video format, perform the following: 1. Press the display menu button. 2.
Page 244 Problem Recommended Action No power. The ignition might not be in on or accessory. The parental control button might have been turned on. (The power indicator light will ﬂash.) Disc will not play. The system might be off. The parental control button might have been turned on.
Page 245 Problem Recommended Action The remote control does Point the remote control not work. directly at the infrared window below the video screen while using. Check that the batteries are not dead or put in wrong. The parental control button might have been turned on.
Page 246: Theft-Deterrent Feature
Theft-Deterrent Feature ® THEFTLOCK is designed to discourage theft of your radio. Your vehicle has a “built in” theft-deterrent feature on each radio that is automatic – there is no programming required. The radio in your vehicle cannot be used in any other vehicle. When the radio was originally installed in your vehicle at the factory, it stored the Vehicle Identiﬁcation Number (VIN).
Page 247 (OnStar/Voice Recognition): If your vehicle has the Radio with CD or Radio with Six-Disc CD audio system, you can press this button to interact with the ® OnStar system. See the OnStar your vehicle for more information. If your vehicle has the optional navigation system, you can press this button to initiate voice recognition.
Page 248: Dvd Distortion
DVD Distortion You may experience audio distortion in the IR headphones when operating cellular phones, scanners, CB radios, Global Positioning Systems (GPS)*, two-way radios, mobile fax, or walkie talkies. It may be necessary to turn off the DVD player when operating one of these devices in or near the vehicle.
Page 249: Care Of Your Cds And Dvds
Care of Your CDs and DVDs Handle discs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a disc is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Page 250: Diversity Antenna System
Diversity Antenna System Your AM-FM antenna is integrated with your rear quarter glass windows, located in the rear of the vehicle on the driver and passenger sides. Be sure that the inside surface of the rear windows are not scratched and that the lines on the glass are not damaged.
Page 251 Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-2 Control of a Vehicle ...4-5 Braking ...4-6 Traction Control System (TCS) ...4-9 Magnetic Ride Control ...4-10 ® Stabilitrak System ...4-10 Panic Brake Assist ...4-11 Steering ...4-12 Off-Road Recovery ...4-14 Passing ...4-14...
Page 252: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-8 . Defensive driving really means “be ready for anything.”...
Page 253 Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured.
Page 254 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 255: Control Of A Vehicle
There is something else about drinking and driving that many people do not know. Medical research shows that alcohol in a person’s system can make crash injuries worse, especially injuries to the brain, spinal cord or heart. This means that when anyone who has been drinking —...
Page 256: Braking
Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about 3/4 of a second. But that is only an average.
Page 257: Anti-Lock Brake System
Anti-lock Brake System Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine and begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on.
Page 258: Braking In Emergencies
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Page 259: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle has a traction control system that limits wheel spin. This is especially useful in slippery road conditions. On a rear-wheel-drive vehicle, the system operates if it senses that one or both of the rear wheels are spinning or beginning to lose traction. On an All-Wheel-Drive (AWD) vehicle the system will operate if it senses that any of the wheels are spinning or beginning to lose traction.
Page 260: Magnetic Ride Control
To turn the system off, press the TC (traction control) button located near the shift lever. If you press the TC button once, the traction control system will turn off and the traction control system warning light will come on. Press the TC button again to turn the system back on.
Page 261: Panic Brake Assist
When the system activates, a Stability System Engaged message will be displayed on the Driver Information Center. See DIC Warnings and Messages on page 3-65 . You may also hear a noise or feel vibration in the brake pedal. This is normal. Continue to steer the vehicle in the direction you want it to go.
Page 262: Steering
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control”...
Page 263: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 264: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you are driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 265 • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 266: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Page 267: Operating Your All-Wheel-Drive Vehicle Off Paved Roads
Operating Your All-Wheel-Drive Vehicle Off Paved Roads This off-road guide is for vehicles that have all-wheel drive. If your vehicle does not have all-wheel drive, you should not drive off-road unless you are on a level, solid surface. Many of the same design features that help make your vehicle responsive on paved roads during poor weather conditions —...
Page 268 Loading Your Vehicle for Off-Road Driving There are some important things to remember about how to load your vehicle. • The heaviest things should be on the load ﬂoor and forward of your rear axle. Put heavier items as far forward as you can.
Page 269: Environmental Concerns
Environmental Concerns Off-road driving can provide wholesome and satisfying recreation. However, it also raises environmental concerns. We recognize these concerns and urge every off-roader to follow these basic rules for protecting the environment: • Always use established trails, roads and areas that have been specially set aside for public off-road recreational driving;...
Page 270: Scanning The Terrain
Controlling your vehicle is the key to successful off-road driving. One of the best ways to control your vehicle is to control your speed. Here are some things to keep in mind. At higher speeds: • you approach things faster and you have less time to scan the terrain for obstacles.
Page 271: Driving On Off-Road Hills
When you drive over obstacles or rough terrain, keep a ﬁrm grip on the steering wheel. Ruts, troughs or other surface features can jerk the wheel out of your hands if you are not prepared. When you drive over bumps, rocks, or other obstacles, your wheels can leave the ground.
Page 272: Driving Uphill
Approaching a Hill When you approach a hill, you need to decide if it is one of those hills that is just too steep to climb, descend or cross. Steepness can be hard to judge. On a very small hill, for example, there may be a smooth, constant incline with only a small change in elevation where you can easily see all the way to the top.
Page 273 CAUTION: Turning or driving across steep hills can be dangerous. You could lose traction, slide sideways, and possibly roll over. You could be seriously injured or killed. When driving up hills, always try to go straight up. • Ease up on your speed as you approach the top of the hill.
Page 274 What should I do if my vehicle stalls, or is about to stall, and I can not make it up the hill? If this happens, there are some things you should do, and there are some things you must not do? First, here is what you should do: •...
Page 275: Driving Downhill
Suppose, after stalling, I try to back down the hill and decide I just can not do it. What should I do? Set the parking brake, put your transmission in PARK (P) and turn off the engine. Leave the vehicle and go get some help. Exit on the uphill side and stay clear of the path the vehicle would take if it rolled downhill.
Page 276 Are there some things I should not do when driving down a hill? Yes! These are important because if you ignore them you could lose control and have a serious accident. • When driving downhill, avoid turns that take you across the incline of the hill.
Page 277: Driving Across An Incline
Driving Across an Incline Sooner or later, an off-road trail will probably go across the incline of a hill. If this happens, you have to decide whether to try to drive across the incline. Here are some things to consider: •...
Page 278: Stalling On An Incline
Stalling on an Incline If your vehicle stalls when you are crossing an incline, be sure you (and your passengers) get out on the uphill side, even if the door there is harder to open. If you get out on the downhill side and the vehicle starts to roll over, you will be right in its path.
Page 279: Driving In Mud, Sand, Snow Or Ice
Driving in Mud, Sand, Snow or Ice When you drive in mud, snow or sand, your wheels will not get good traction. You can not accelerate as quickly, turning is more difficult, and you will need longer braking distances. It is best to use a low gear when you are in mud — the deeper the mud, the lower the gear.
Page 280: Driving In Water
Driving in Water Heavy rain can mean ﬂash ﬂooding, and ﬂood waters demand extreme caution. Find out how deep the water is before you drive through it. If it is deep enough to cover your wheel hubs, axles or exhaust pipe, do not try it — you probably will not get through.
Page 281: Driving At Night
After Off-Road Driving Remove any brush or debris that has collected on the underbody, chassis or under the hood. These accumulations can be a ﬁre hazard. After operation in mud or sand, have the brake linings cleaned and checked. These substances can cause glazing and uneven braking.
Page 282 Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Since you can not see as well, you may need to slow down and keep more space between you and other vehicles. • Slow down, especially on higher speed roads.
Page 283: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can not stop, accelerate or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 284 Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can not, try to slow down before you hit them. 4-34 CAUTION: Wet brakes can cause accidents.
Page 285: Driving Through Flowing Water
Hydroplaning Hydroplaning is dangerous. So much water can build up under your tires that they can actually ride on the water. This can happen if the road is wet enough and you are going fast enough. When your vehicle is hydroplaning, it has little or no contact with the road.
Page 286: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. 4-36 Here are ways to increase your safety in city driving: •...
Page 287: Freeway Driving
Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 288: Before Leaving On A Long Trip
When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up. Drive on to the next exit. The exit ramp can be curved, sometimes quite sharply. The exit speed is usually posted.
Page 289: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 290 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system and transaxle.
Page 291: Driving On Snow Or Ice
Winter Driving Here are some tips for winter driving: • Have your vehicle in good shape for winter. • You may want to put winter emergency supplies in your vehicle. Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth and a couple of reﬂective warning triangles.
Page 292 What is the worst time for this? “Wet ice.” Very cold snow or ice can be slick and hard to drive on. But wet ice can be even more trouble because it may offer the least traction of all. You can get wet ice when it is about freezing (32°F;...
Page 293 If You Are Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. Here are some things to do to summon help and keep yourself and your passengers safe: •...
Page 294 You can run the engine to keep warm, but be careful. 4-44 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You can not see it or smell it, so you might not know it is in your vehicle.
Page 295: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 296: Using The Recovery Hook
Rocking Your Vehicle To Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has the ® Stabilitrak System, turn the system off by pressing and holding the Traction button so that the STABILITY SYS DISABLED message and the traction off light are illuminated on the instrument panel cluster.
Page 297: Towing
Towing Towing Your Vehicle Consult your dealer or a professional towing service if you need to have your disabled vehicle towed. See Roadside Service on page 7-6 . If you want to tow your vehicle behind another vehicle for recreational purposes (such as behind a motorhome), see Recreational Vehicle Towing following.
Page 298: Loading Your Vehicle
Dolly Towing If your vehicle is a rear-wheel drive, it can be towed using a dolly. If you have an All-Wheel-Drive (AWD) vehicle, it can only be towed on a ﬂat-bed trailer. To tow your vehicle using a dolly, follow these steps: 1.
Page 299 Tire and Loading Information Label A. Vehicle Capacity Weight The Tire and Loading Information label is attached to the center pillar, near the driver’s door latch. Vehicles without a center pillar will have the Tire and Loading Information label attached to the driver’s door edge. This label lists the number of people that can be in your vehicle and the total weight it can carry.
Page 300: Loading Your Vehicle
4. The resulting ﬁgure equals the available amount of cargo and luggage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be ﬁve 150 lb. passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 750 (5 x 150) = 650 lbs.).
Page 301 Example 2 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 2 Subtract Occupant Weight 150 lbs (68 Available Cargo Weight Total Item 1,000 lbs (453 kg) 750 lbs (340 kg) 250 lbs (113 kg) Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions.
Page 302 Certiﬁcation/Tire Label The Certiﬁcation/Tire label is found on the driver’s door edge. The label shows the size of your original tires and the inﬂation pressures needed to obtain the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR).
Page 303: Level Control
If you put things inside your vehicle — like suitcases, tools, packages, or anything else — they will go as fast as the vehicle goes. If you have to stop or turn quickly, or if there is a crash, they’ll keep going. CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or...
Page 304: Towing A Trailer
Towing a Trailer CAUTION: If you do not use the correct equipment and drive properly, you can lose control when you pull a trailer. For example, if the trailer is too heavy, the brakes may not work well — or even at all.
Page 305: If You Do Decide To Pull A Trailer
You can ask your dealer for our trailering information or advice, or you can write us at: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169...
Page 306: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 307: Total Weight On Your Vehicle's Tires
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You’ll ﬁnd these numbers on the Certiﬁcation/Tire label. See Loading Your Vehicle on page 4-48 . Then be sure you don’t go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Page 308: Driving With A Trailer
Driving with a Trailer Towing a trailer requires a certain amount of experience. Before setting out for the open road, you’ll want to get to know your rig. Acquaint yourself with the feel of handling and braking with the added weight of the trailer. And always keep in mind that the vehicle you are driving is now a good deal longer and not nearly as responsive as your vehicle is by itself.
Page 309: Turn Signals When Towing A Trailer
Turn Signals When Towing a Trailer When you tow a trailer, your vehicle may need a different turn signal ﬂasher and/or extra wiring. Check with your dealer. The arrows on your instrument panel will ﬂash whenever you signal a turn or lane change.
Page 310: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • start your engine, • shift into a gear, and • release the parking brake. 2. Let up on the brake pedal. 3.
Page 311 Section 5 Service ...5-3 Doing Your Own Service Work ...5-3 Adding Equipment to the Outside of Your Vehicle ...5-4 Fuel ...5-4 Gasoline Octane ...5-4 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuels in Foreign Countries ...5-6 Filling Your Tank ...5-7 Filling a Portable Fuel Container ...5-10 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 312 Section 5 Buying New Tires ...5-73 Uniform Tire Quality Grading ...5-74 Wheel Alignment and Tire Balance ...5-75 Wheel Replacement ...5-75 Tire Chains ...5-77 If a Tire Goes Flat ...5-77 Changing a Flat Tire ...5-78 Compact Spare Tire ...5-91 Appearance Care ...5-92 Cleaning the Inside of Your Vehicle ...5-92 Care of Safety Belts ...5-94 Weatherstrips ...5-94...
Page 313: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 314: Adding Equipment To The Outside Of Your Vehicle
CAUTION: (Continued) • Be sure you have sufficient knowledge, experience, the proper replacement parts and tools before you attempt any vehicle maintenance task. • Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off.
Page 315: Gasoline Speciﬁcations
Gasoline Speciﬁcations It is recommended that gasoline meet speciﬁcations which were developed by automobile manufacturers around the world and contained in the World-Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www.autoalliance.org. Gasoline meeting these speciﬁcations could provide improved driveability and emission control system performance compared to other gasoline.
Page 316: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel.
Page 317: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 318 While refueling, hang the fuel cap by the tether from the hook on the fuel door. To remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has a spring in it; if you let go of the cap too soon, it will spring back to the right.
Page 319 When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 320: Filling A Portable Fuel Container
Filling a Portable Fuel Container CAUTION: Never ﬁll a portable fuel container while it is in your vehicle. Static electricity discharge from the container can ignite the gasoline vapor. You can be badly burned and your vehicle damaged if this occurs. To help avoid injury to you and others: •...
Page 321: Hood Release
Hood Release To lift the hood, use the following steps: 1. Pull the lever inside the vehicle to open the hood. It is located on the lower left side of the instrument panel. 2. Then go to the front of the vehicle and ﬁnd the secondary hood release lever.
Page 322: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the 3.6L V6, you’ll see the following: 5-12...
Page 323 A. Underhood Fuse Block. See Fuses and Circuit Breakers on page 5-100 . B. Windshield Washer Fluid Reservoir. See Windshield Washer Fluid on page 5-37 . C. Battery. See Battery on page 5-41 . D. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-36 .
Page 324 When you open the hood on the 4.6L V8, you’ll see the following: 5-14...
Page 325 A. Underhood Fuse Block. See Fuses and Circuit Breakers on page 5-100 . B. Battery. See Battery on page 5-41 . C. Passenger Compartment Air Filter. See Passenger Compartment Air Filter on page 3-35 . D. Windshield Washer Fluid Reservoir. See Windshield Washer Fluid on page 5-37 .
Page 326: Engine Oil
Engine Oil If the oil pressure light and/or the Oil Pressure Low — Stop Engine message on the DIC appears on the instrument cluster, it means you need to check your engine oil level right away. For more information, see “Oil Pressure Low — Stop Engine”...
Page 327: When To Add Engine Oil
4.6L V8 Engine When to Add Engine Oil If the oil is below the cross-hatched area at the tip of the dipstick for the 3.6L V6 engine or below the indentation at the tip of the dipstick for the 4.6L V8 engine, then you will need to add at least one quart of oil.
Page 328: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for two things: • GM4718M Your vehicle’s engine requires a special oil meeting GM Standard GM4718M. Oils meeting this standard may be identiﬁed as synthetic. However, not all synthetic oils will meet this GM standard. You should look for and use only an oil that meets GM Standard GM4718M.
Page 329: Engine Oil Additives
• SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, you can use SAE 10W-30 if it is going to be 0°F (–18°C) or above. These numbers on an oil container show its viscosity, or thickness.
Page 330: When To Change Engine Oil
When to Change Engine Oil (GM Oil Life System) Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
Page 331 After the oil has been changed, the Change Engine Oil message and the oil life indicator must be reset. To reset the message and indicator, use one of the following procedures: Base Audio System Press the CLR button located to the right of the DIC display to acknowledge the Change Engine Oil message.
Page 332: What To Do With Used Oil
What to Do with Used Oil Used engine oil contains certain elements that may be unhealthy for your skin and could even cause cancer. Do not let used oil stay on your skin for very long. Clean your skin and nails with soap and water, or a good hand cleaner.
Page 333: When To Inspect The Engine Air Cleaner/Filter
When to Inspect the Engine Air Cleaner/Filter Inspect the air cleaner/ﬁlter at every oil change and replace it at the ﬁrst oil change after 25,000 miles (40 000 km) How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/ﬁlter remove the ﬁlter from the vehicle and lightly shake the ﬁlter to release loose dust and dirt.
Page 334: Automatic Transmission Fluid
Automatic Transmission Fluid It is not necessary to check the transmission ﬂuid level. A transmission ﬂuid leak is the only reason for ﬂuid loss. If a leak occurs, take your vehicle to the dealership service department and have it repaired as soon as possible.
Page 335: Engine Coolant
Navigation System To reset the transmission ﬂuid life indicator, use the following steps: 1. Turn the vehicle on with the ignition in RUN. 2. Turn the Navigation system on by pressing the PWR/VOL knob. 3. Press and hold the vehicle information button in the upper right corner of the screen for three seconds.
Page 336: What To Use
What to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 337: Coolant Surge Tank Pressure Cap
CAUTION: Turning the surge tank pressure cap when the engine and radiator are hot can allow steam and scalding liquids to blow out and burn you badly. Never turn the surge tank pressure cap — even a little — when the engine and radiator are hot.
Page 338: If Steam Is Coming From Your Engine
Overheated Engine Protection Operation Mode This emergnecy operating mode allows your vehicle to be driven to a safe place in an emergency situation. Should an overheated engine condition exist, an overheat protection mode which alternates ﬁring groups of cylinders helps prevent engine damage. In this mode, you will notice a signiﬁcant loss in power and engine performance.
Page 339: If No Steam Is Coming From Your Engine
CAUTION: (Continued) Wait until there is no sign of steam or coolant before you open the hood. If you keep driving when your engine is overheated, the liquids in it can catch ﬁre. You or others could be badly burned. Stop your engine if it overheats, and get out of the vehicle until the engine is cool.
Page 340: Cooling System
Cooling System When you decide it’s safe to lift the hood, here’s what you’ll see: 3.6L HFV6 shown A. Electric Engine Cooling Fan(s) B. Coolant Surge Tank and Pressure Cap 5-30 CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 341 When the engine is cold, the coolant level should be at or slightly above the FULL COLD/FROID line on the side of the coolant surge tank. If it isn’t, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 342: How To Add Coolant To The Coolant Surge Tank
How to Add Coolant to the Coolant Surge Tank If you haven’t found a problem yet, check to see if coolant is visible in the surge tank. If coolant is visible but the coolant level isn’t at the FULL COLD/FROID line on the side of the coolant surge tank, add a 50/50 mixture of clean, drinkable water and DEX-COOL coolant at the coolant surge tank, but be sure the...
Page 343 CAUTION: (Continued) Your vehicle’s coolant warning system is set for the proper coolant mixture. With plain water or the wrong mixture, your engine could get too hot but you would not get the overheat warning. Your engine could catch ﬁre and you or others could be burned.
Page 344 2. Then keep turning the pressure cap slowly, and 3. Then ﬁll the coolant surge tank with the proper remove it. mixture, to slightly above the FULL COLD/FROID line on the side of the coolant surge tank. 5-34...
Page 345 4. With the coolant surge tank pressure cap off, start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. By this time, the coolant level inside the coolant surge tank may be lower.
Page 346: Power Steering Fluid
Power Steering Fluid The power steering ﬂuid reservoir is located in the center of the engine compartment, toward the front. See Engine Compartment Overview on page 5-12 for more information on location. 5-36 When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise.
Page 347: Windshield Washer Fluid
Windshield Washer Fluid What to Use When you need windshield washer ﬂuid, be sure to read the manufacturer’s instructions before use. If you will be operating your vehicle in an area where the temperature may fall below freezing, use a ﬂuid that has sufficient protection against freezing.
Page 348: Brakes
Brakes Brake Fluid Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 349: Checking Brake Fluid
Checking Brake Fluid You can check the brake ﬂuid without taking off the cap. Just look at the brake ﬂuid reservoir. The ﬂuid level should be above MIN. If it is not, have your brake system checked to see if there is a leak. After work is done on the brake hydraulic system, make sure the level is above the MIN but not over the MAX mark.
Page 350: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal ﬁrmly).
Page 351: Battery
If you do not, your brakes may no longer work properly. For example, if someone puts in brake linings that are wrong for your vehicle, the balance between your front and rear brakes can change — for the worse. The braking performance you have come to expect can change in many other ways if someone puts in the wrong replacement brake parts.
Page 352: Jump Starting
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to follow the steps below to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 353 4. Open the hoods and locate the batteries. Find the positive (+) and negative ( ) terminal locations on each vehicle. See Engine Compartment Overview on page 5-12 for more information on location of the battery. CAUTION: An electric fan can start up even when the engine is not running and can injure you.
Page 354 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock.
Page 355 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery. Use a remote positive (+) terminal if the vehicle has one. 8. Now connect the black negative ( ) cable to the negative terminal of the good battery.
Page 356 9. Connect the other end of the negative ( ) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less.
Page 357 Jumper Cable Removal A. Heavy, Unpainted Metal Engine Part B. Good Battery or Remote Positive (+) Terminal C. Dead Battery or Remote Positive (+) Terminal To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery.
Page 358: All-Wheel Drive
All-Wheel Drive Lubricant checks in this section also apply to these vehicles. However, there are two additional systems that need lubrication. Transfer Case When to Check Lubricant It is not necessary to regularly check the transfer case ﬂuid unless you suspect there is a leak or you hear an unusual noise.
Page 359: Rear Axle
Rear Axle When to Check Lubricant It is not necessary to regularly check the rear axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 360: Front Axle
Front Axle When to Check and Change Lubricant It is not necessary to regularly check the front axle ﬂuid unless you suspect there is a leak or you hear an unusual noise. A ﬂuid loss could indicate a problem. Have it inspected and repaired. How to Check Lubricant (A) Drain Plug (B) Filler Plug To get an accurate reading, the vehicle should be on a...
Page 361: Bulb Replacement
Bulb Replacement For the proper type of replacement bulb, see Replacement Bulbs on page 5-55 . For any bulb changing procedure not listed in this section, contact your dealer. High Intensity Discharge (HID) Lighting Your vehicle may be equipped with HID headlamps. CAUTION: The low beam high intensity discharge lighting system operates at a very high voltage.
Page 362 To remove the headlamp assembly from the vehicle and access the bulbs, follow these steps: 1. Open the hood. See Hood Release on page 5-11 for more information. 2. Use a tool to remove all of the fasteners along the top surface of the front fascia.
Page 363: Front Turn Signal And Fog Lamps
8. Reinstall the two fasteners on top of the headlamp assembly. 9. Reinstall the screw at the lower inboard side of the headlamp assembly through the hole in the bracket into the headlamp. 10. Reinstall the fasteners along the top surface of the front fascia.
Page 364: Sidemarker Lamps
6. If you are replacing the fog lamp bulb, disconnect the electrical connector from the back of the bulb socket. 7. Turn the bulb socket one-quarter turn counterclockwise to remove it from the assembly. 8. Replace the bulb. See Replacement Bulbs on page 5-55 for the proper bulb number.
Page 365: Back-Up And License Plate Lamps
Back-Up and License Plate Lamps To replace the back-up and/or license plate lamps, use the following procedure: 1. Open the liftgate. 2. Remove the liftgate trim panel on the interior of the liftgate by pulling the trim panel snap-in fasteners out of the retainers and also by using a tool to remove the screw on the bottom right side of the trim panel.
Page 366: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See Owner Checks and Services on page 6-8 . It’s a good idea to clean or replace the wiper blade assembly on a regular basis or when worn. For proper windshield wiper blade length and type, see Normal Maintenance Replacement Parts on page 6-13 .
Page 367 Notice: Allowing the wiper blade arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by your warranty. Do not allow the wiper blade arm to touch the windshield.
Page 368: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 369: Winter Tires
Winter Tires If you expect to drive on snow or ice covered roads often, you may want to get winter tires for your vehicle. All season tires provide good overall performance on most surfaces but they may not offer the traction you would like or the same level of performance as winter tires on snow or ice covered roads.
Page 370 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size Code” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a...
Page 371 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a...
Page 372 (E) Tire Identiﬁcation Number (TIN): The letters and numbers following DOT code are the Tire Identiﬁcation Number (TIN). The TIN shows the manufacturer and plant code, tire size, and date the tire was manufactured. The TIN is molded onto both sides of the tire, although only one side may have the date of manufacture.
Page 373 (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 374: Tire Size
Tire Size The following illustrations show the different parts of a tire size code. Passenger (P-Metric) Tire (A) Passenger (P-Metric) Tire: The United States version of a metric tire sizing system. The letter “P” as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.S.
Page 375 Light Truck (LT-Metric) Tire (A) Light Truck (LT-Metric) Tire: The United States version of a metric tire sizing system. The letter “LT” as the ﬁrst two characters in the tire size means a light truck tire engineered to standards set by the U.
Page 376: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Page 377 Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire may be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire.
Page 378: Inﬂation - Tire Pressure
Treadwear Indicators: Narrow bands, sometimes called “wear bars,” that show across the tread of a tire when only 2/32 inch of tread remains. See When It Is Time for New Tires on page 5-72 . UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear.
Page 379: When To Check
When to Check Check your tires once a month or more. Also, check the tire pressure of the compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure.
Page 380 Driving on a signiﬁcantly under-inﬂated tire causes the tire to overheat and can lead to tire failure. Under-inﬂation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Each tire, including the spare, should be checked monthly when cold and set to the recommended inﬂation pressure as speciﬁed in the vehicle placard and owner’s manual.
Page 381 5. Start with the left (driver’s side) front tire. 6. Remove the valve cap from the valve stem. Activate the TPM sensor by increasing or decreasing the tire’s air pressure for 5 seconds, or until a horn chirp sounds. The horn chirp, which may take up to 30 seconds, conﬁrms that the sensor identiﬁcation code has been matched to this tire position.
Page 382: Tire Inspection And Rotation
Tire Inspection and Rotation The tires on your vehicle are different sizes front to rear. Due to this, your tires should not be rotated. Each tire and wheel should be used only in the position it is in. Check your tires and wheels regularly for unusual wear and damage.
Page 383: Buying New Tires
Buying New Tires To ﬁnd out what kind and size of tires you need, look at the Certiﬁcation/Tire label or the Tire and Loading Information label. See Loading Your Vehicle on page 4-48 , for examples of the labels and where they can be found on your vehicle.
Page 384: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 385: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 386: Used Replacement Wheels
Each new wheel should have the same load-carrying capacity, diameter, width, offset and be mounted the same way as the one it replaces. If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts.
Page 387: Tire Chains
Tire Chains Notice: Use tire chains only where legal and only when you must. Use only SAE Class S type chains that are the proper size for your tires. Install them on the rear axle tires and tighten them as tightly as possible with the ends securely fastened.
Page 388: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 389: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you’ll need is located in the rear of the vehicle. 1. If your vehicle has the cargo management system, remove the storage bin to access the jack. If your vehicle has the third row seat, remove the head rest storage tray to access the jack.
Page 390 Removing the Spare Tire The compact spare tire is located under the vehicle, ahead of the rear bumper. See Compact Spare Tire on page 5-91 for more information about the compact spare. A. Wheel Wrench B. Cable C. Retainer D. Compact Spare Tire 5-80 1.
Page 391: Secondary Latch System
If the spare tire will not lower, the secondary latch may be engaged causing the tire not to lower. Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it’s not visible, see “Secondary Latch System” following.
Page 392 To release the spare tire from the secondary latch, do the following: CAUTION: Someone standing too close during the procedure could be injured by the jack. If the spare tire does not slide off the jack completely, make sure no one is behind you or on either side of you as you pull the jack out from the spare.
Page 393 7. Lower the jack by turning the wheel wrench counterclockwise. Keep lowering the jack until the spare tire is resting on the wheel wrench. 8. Grasp the spare tire with both hands and pull it out from under the vehicle. 9.
Page 394: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire 1. Using the ﬂat end of the wheel wrench, pry off the center cap at the notch. Be careful; the edges may be sharp. Don’t try to remove the cover with your bare hands.
Page 395 4. Attach the wheel wrench to the jack. 5. Turn the wheel wrench clockwise to raise the jack lift head until the jack just ﬁts under the vehicle. 6. Raise the jack by turning the wheel wrench clockwise until the slots in the jack head ﬁt into the metal ﬂange located behind the triangle on the plastic molding as shown.
Page 396 10. Remove any rust or dirt from the wheel bolts, mounting surfaces and spare wheel. CAUTION: Rust or dirt on the wheel, or on the parts to which it is fastened, can make the wheel nuts become loose after a time. The wheel could come off and cause an accident.
Page 397: Storing The Flat Tire And Tools
13. Tighten the wheel nuts ﬁrmly in a crisscross sequence, as shown. CAUTION: Incorrect wheel nuts or improperly tightened wheel nuts can cause the wheel to become loose and even come off. This could lead to an accident. Be sure to use the correct wheel nuts.
Page 398 Storing the Flat Tire with Third Row Passengers Put back all tools as they were stored in the rear storage compartment and put the compartment cover back on. 1. Use the power third row seat button near the liftgate to tilt the third row seatback forward slightly. 2.
Page 399: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. CAUTION: The underbody-mounted spare tire needs to be stored with the valve stem pointing down.
Page 400 4. Attach the wheel wrench to the hoist shaft. 5. Turn the wheel wrench clockwise to lift the spare tire. 6. When the tire is almost in the stored position, turn the tire so that the valve stem is towards the rear of the vehicle.
Page 401: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when your vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inﬂated.
Page 402: Appearance Care
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into ﬂames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space.
Page 403: Cleaning Leather
Here are some cleaning tips: • Always read the instructions on the cleaner label. • Clean up stains as soon as you can — before they set. • Carefully scrape off any excess stain. • Use a clean cloth or sponge, and change to a clean area often.
Page 404: Cleaning Interior Plastic Components
Cleaning Interior Plastic Components Use on a mild soap and water solution on a soft cloth or sponge. Commercial cleaners may affect the surface ﬁnish. Cleaning Wood Panels Use a clean cloth moistened in warm, soapy water (use mild dish washing soap). Dry the wood immediately with a clean cloth.
Page 405: Cleaning The Outside Of Your Vehicle
Cleaning the Outside of Your Vehicle The paint ﬁnish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s ﬁnish is to keep it clean by washing it often with lukewarm or cold water. Do not wash your vehicle in the direct rays of the sun.
Page 406: Cleaning Aluminum Or Chrome-Plated Wheels
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s ﬁnish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.
Page 407: Cleaning Tires
Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Page 408: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil Remover and asphalt. Chrome Cleaner Use on chrome or and Polish stainless steel.
Page 409: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 410: Electrical System
Electrical System Add-On Electrical Equipment Notice: Don’t add anything electrical to your vehicle unless you check with your dealer ﬁrst. Some electrical equipment can damage your vehicle and the damage wouldn’t be covered by your warranty. Some add-on electrical equipment can keep other components from working as they should.
Page 411: Underhood Fuse Block
Underhood Fuse Block The underhood fuse block is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. To access the fuses, push in the two tabs located on each side of the fuse block cover.
Page 412 Relays HORN RELAY Horn MICRO HI BEAM High-Beam Headlamps RELAY MICRO DRL RELAY Daytime Running Lamps MICRO-OPT LO BEAM RELAY/HID Low-Beam HID Headlamps (Option) MINI-OPT HDLP WASH RELAY Headlamp Washer Motor (Option) MINI-OPT CIGAR RELAY Cigarette Lighter MINI BLOWER Front Blower RELAY MINI FOG LAMP RELAY MICRO Fog Lamps...
Page 413 Fuses Usage Passenger’s Side Taillamp RT PARK Assembly, Front Sidemarker and Front Parking Lamp Assembly HORN Dual Horn Assembly LT HI BEAM Driver’s Side High-Beam Headlamp LT LOW BEAM Driver’s Side Low-Beam Headlamp RT LOW BEAM Passenger’s Side Low-Beam Headlamp Passenger’s Side High-Beam RT HI BEAM Headlamp...
Page 414 Fuses ECM, TCM, IPC, ECM/TCM ® PASS-Key III+ Module WPR MOD Windshield Wiper Module Assembly POSTO2 Post O2 Sensors COMP CLUTCH Compressor Clutch WPR SW Windshield Wiper/Washer Switch FOG LAMP Fog Lamps Center Console Accessory OUTLET Power Outlet EVEN COILS Even Injection Coils Instrument Panel Accessory I/P OUTLET...
Page 415: Rear Underseat Fuse Block
Rear Underseat Fuse Block (Driver’s Side) The driver’s side rear fuse block is located under the rear seat on the driver’s side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 416 Relays SPARE Not Used REV LAMP ISRVM (Inside Rearview Mirror), RELAY MICRO License Plate Lamp Assembly Fuses L FRT HTD Driver’s Heated Seat Module SEAT MOD MEM/ADAPT Driver’s Power Seat Switch, SEAT Memory Seat Module Universal Garage Door Opener, THEFT Intrusion Sensor, Diversity Antenna Module REVERSE...
Page 417: Passenger's Side
Rear Underseat Fuse Block (Passenger’s Side) The passenger’s side rear fuse block is located under the rear seat on the passenger’s side of the vehicle. The carpet must be lifted up to access the rear fuse block. To access the fuse block, push in the two tabs located at each end of the fuse block cover.
Page 418 Relays REAR FOG LAMP Rear Fog Lamps (Export Only) RLY MICRO FUEL PUMP MOTOR Fuel Pump Motor RLY MICRO Fuses INTERIOR Hush Panel Lamps, Puddle Lamps, LAMP Overhead Courtesy Lamp Assembly RT FRT Passenger’s Door Module DR MOD RIM (Rear Integration Module), Ignition Switch, Key Lock Cylinder REAR FOG Rear Fog Lamps (Export Only)
Page 419: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. See Recommended Fluids and Lubricants on page 6-11 for more information. Application Air Conditioning Refrigerant R134a Use Refrigerant Oil, R134a Systems Front A/C Front and Rear A/C Automatic Transmission Cooling System 3.6L HFV6...
Page 420: Engine Speciﬁcations
Engine Speciﬁcations Engine 3.6L HFV6 (LY7) 4.6L PV8 (LH2) 5-110 VIN Code Transmission M82=Rear-Wheel Drive, 5L40-E MX5=All-Wheel Drive, 5L40-E M22=Rear-Wheel Drive, 5L50-E MV3=All-Wheel Drive, 5L50-E Spark Plug Gap 0.044 inches (1.1 mm) 0.040 inches (1.0 mm)
Page 421 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-3 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-11...
Page 422: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 423: Using Your Maintenance Schedule
Using Your Maintenance Schedule We at General Motors want to help you keep your vehicle in good working condition. But we do not know exactly how you will drive it. You may drive very short distances only a few times a week. Or you may drive long distances all the time in very hot, dusty weather.
Page 424: Scheduled Maintenance
If you want to get service information, see Service Publications Ordering Information on page 7-12 . Owner Checks and Services on page 6-8 tells you what should be checked, when to check it and what you can easily do to help keep your vehicle in good condition. The proper replacement parts, ﬂuids and lubricants to use are listed in Recommended Fluids and Lubricants on page 6-11 and Normal Maintenance Replacement...
Page 425 Service Maintenance I Maintenance II Change engine oil and ﬁlter. Reset oil life system. See Engine Oil on page 5-16 . An Emission Control Service. Lubricate chassis components. See footnote #. Visually check for any leaks or damage. See footnote (g). Inspect engine air cleaner ﬁlter.
Page 426: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 427: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 428: Owner Checks And Services
(g) A ﬂuid loss in any vehicle system could indicate a problem. Have the system inspected and repaired and the ﬂuid level checked. Add ﬂuid if needed. (h) Change automatic transmission ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: −...
Page 429: At Least Once A Month
Engine Coolant Level Check Check the engine coolant level and add ® DEX-COOL coolant mixture if necessary. See Engine Coolant on page 5-25 for further details. Windshield Washer Fluid Level Check Check the windshield washer ﬂuid level in the windshield washer tank and add the proper ﬂuid if necessary.
Page 430 Automatic Transmission Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 431: Recommended Fluids And Lubricants
Park on a fairly steep hill, with the vehicle facing downhill. Keeping your foot on the regular brake, set the parking brake. • To check the parking brake’s holding ability: With the engine running and transmission in NEUTRAL (N), slowly remove foot pressure from the regular brake pedal.
Page 432 Usage Fluid/Lubricant Hydraulic Brake Delco Supreme 11 Brake Fluid or System equivalent DOT-3 brake ﬂuid. Windshield ® Washer Solvent GM Optikleen GM Power Steering Fluid (GM Part Power Steering No. U.S. 89021184, in Canada System 89021186). ® Automatic DEXRON -III Automatic Transmission Transmission Fluid.
Page 433: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from you dealer. Part Engine Air Cleaner/Filter Engine Oil Filter 3.6L HFV6 4.6L V8 Passenger Compartment Air Filter Element Spark Plugs 3.6L HFV6 4.6L V8 Windshield Wiper Blade (Hook Type) Driver’s Side...
Page 434: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. Also, you should retain all maintenance receipts.
Page 435 Maintenance Record (cont’d) Odometer Maintenance I or Services Performed Date Serviced By Reading Maintenance II 6-15...
Page 436 Maintenance Record (cont’d) Odometer Maintenance I or Services Performed Date Serviced By Reading Maintenance II 6-16...
Page 437 Section 7 Customer Assistance and Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-3 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Program for Persons with Disabilities ...7-5 Roadside Service ...7-6 Courtesy Transportation ...7-7 Vehicle Data Collection and Event Data Records ...7-10 Customer Assistance and Information...
Page 438: Customer Assistance And Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Cadillac. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 439: Online Owner Center
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within...
Page 440: Customer Assistance For Text Telephone (Tty) Users
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Cadillac has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Cadillac by dialing: 1-800-833-CMCC (2622). (TTY users in Canada can dial 1-800-263-3830.)
Page 441: Gm Mobility Program For Persons With Disabilities
Overseas – Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) – Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 442: Roadside Service
Roadside Service Cadillac’s exceptional Roadside Service is more than an auto club or towing service. It provides every Cadillac owner with the advantage of contacting a Cadillac advisor and, where available, a Cadillac trained dealer technician who can provide on-site service.
Page 443: Courtesy Transportation
A dealer technician, if available, can travel to your location within a 30 mile (50 km) radius of a participating Cadillac dealership. If beyond this radius, we will arrange to have your car towed to the nearest Cadillac dealership.
Page 444: Plan Ahead When Possible
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Cadillac helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 445: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum of $40 a day and must be supported by receipts.
Page 446: Vehicle Data Collection And Event Data Records
Vehicle Data Collection and Event Data Records Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the...
Page 447: Reporting Safety Defects
In addition, once GM collects or receives data, GM may • use the data for GM research needs, • make it available for research where appropriate conﬁdentiality is to be maintained and need is shown, or • share summary data which is not tied to a speciﬁc vehicle with non-GM organizations for research purposes.
Page 448: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-458-8006, or write: Cadillac Customer Assistance Center Cadillac Motor Car Division P.O. Box 33169 Detroit, MI 48232-5169 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 449: Service Bulletins
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 450 NOTES 7-14...
Page 451 Accessing the DIC Main Menu (Base Audio System) ... 3-61 Accessory Power Outlets ... 3-24 Activating Program Type (PTY) Stations (RDS and XM™) ... 3-103 Adding Washer Fluid ... 5-37 Additional Program Information ... 7-9 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-100 Adjustable Throttle and Brake Pedal ...
Page 452 Sidemarker Lamps ... 5-54 Taillamps, Turn Signal, Stoplamps and Sidemarker Lamps ... 5-54 Buying New Tires ... 5-73 Cadillac Owner Privileges™ ... 7-6 California Fuel ... 5-5 Canada – Customer Assistance ... 7-4 Canadian Owners ... ii Capacities and Speciﬁcations ... 5-109 Carbon Monoxide ...
Page 453 Care of (cont.) Cargo Cover ... 2-47 Cargo Management System ... 2-47 CD Messages ... 3-110 Cell Phone Storage Area ... 2-45 Cellular Phone Usage ... 3-126 Center Console Storage Area ... 2-45 Center High-Mounted Stoplamp (CHMSL) ... 5-54 Chains, Tires ... 5-77 Change Engine Oil ...
Page 454 Cleaning Tires ... 5-97 Cleaning Vinyl ... 5-93 Cleaning Windshield and Wiper Blades ... 5-96 Cleaning Wood Panels ... 5-94 Climate Control System Air Filter, Passenger Compartment ... 3-35 Dual ... 3-26 Outlet Adjustment ... 3-32 Rear Air Conditioning System ... 3-34 Compact Spare Tire ...
Page 455 Door (cont.) Power Door Locks ... 2-9 Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Driver Position, Safety Belt ... 1-14 Driver Door Ajar ... 3-67 Driver Information Center (DIC) ... 3-52 DIC Main Menu ... 3-61 DIC Vehicle Personalization ...
Page 456 Engine (cont.) Coolant Temperature Gage ... 3-45 Coolant Temperature Warning Light ... 3-44 Engine Compartment Overview ... 5-12 Exhaust ... 2-32 Oil ... 5-16 Overheating ... 5-27 Starting ... 2-23 Engine Coolant Hot – AC (Air Conditioning) Off ... 3-68 Engine Coolant Hot –...
Page 457 Fuel (cont.) Filling a Portable Fuel Container ... 5-10 Filling Your Tank ... 5-7 Fuels in Foreign Countries ... 5-6 Gage ... 3-51 Gasoline Octane ... 5-4 Gasoline Speciﬁcations ... 5-5 Fuel Level Low ... 3-68 Fuses Fuses and Circuit Breakers ... 5-100 Windshield Wiper ...
Page 458 ® HomeLink Transmitter ... 2-40 ® HomeLink Transmitter, Programming ... 2-41 Hood Checking Things Under ... 5-10 Release ... 5-11 Horn ... 3-7 How the System Works ... 3-23 How to Add Coolant to the Coolant Surge Tank ... 5-32 How to Check ...
Page 459 Lamps Exterior ... 3-18 Interior ... 3-21 Lap-Shoulder Belt ... 1-14, 1-23 LATCH System Child Restraints ... 1-42 Securing a Child Restraint Designed for the LATCH System ... 1-44 Leaving Your Vehicle ... 2-11 Leaving Your Vehicle With the Engine Running ... 2-30 Left Rear Door Ajar ...
Page 460 Magnetic Ride Control ... 4-10 Maintenance Schedule Additional Required Services ... 6-6 At Each Fuel Fill ... 6-8 At Least Once a Month ... 6-9 At Least Once a Year ... 6-9 Introduction ... 6-2 Maintenance Footnotes ... 6-7 Maintenance Record ... 6-14 Maintenance Requirements ...
Page 461 Odometer ... 3-38 Off-Road Recovery ... 4-14 Engine ... 5-16 Pressure Light ... 3-48 Oil Pressure Low – Stop Engine ... 3-69 Older Children, Restraints ... 1-28 Online Owner Center ... 7-3 ® OnStar Personal Calling ... 2-40 ® OnStar Services ...
Page 462 Power (cont.) Windows ... 2-14 Power Steering ... 4-12 Pretensioners, Safety Belt ... 1-27 Programmable Automatic Door Locks ... 2-10 ® Programming the HomeLink Transmitter ... 2-41 Programming the Power Windows ... 2-15 Questions and Answers About Safety Belts ... 1-13 Radio Data System (RDS) ...
Page 463 Replacing Brake System Parts ... 5-40 Replacing Restraint System Parts After a Crash ... 1-61 Reporting Safety Defects Canadian Government ... 7-12 General Motors ... 7-12 United States Government ... 7-11 Reprogramming a Single HomeLink Resetting Defaults ... 2-44 Restraint System Check Checking Your Restraint Systems ...
Page 464 Seats (cont.) Manual Passenger ... 1-2 Memory ... 2-52 Power Lumbar ... 1-3 Power Seats ... 1-2 Rear Seat Operation ... 1-7 Reclining Seatbacks ... 1-4 Stowable Seat ... 1-7 Secondary Latch System ... 5-81 Securing a Child Restraint Designed for the LATCH System ... 1-44 Rear Seat Position ...
Page 465 Starting Disabled – Throttle Problem ... 3-72 Starting Your Engine ... 2-23 Status of Vehicle Systems, DIC ... 3-53 Steering ... 4-12 Steering Column Ignition Lock Release ... 2-22 Steering in Emergencies ... 4-13 Steering Tips ... 4-12 Steering Wheel Controls, Audio ... 3-124 Stereo RCA Jacks ...
Page 466 Tires (cont.) Inspection and Rotation ... 5-72 Pressure Monitor System ... 5-69 Uniform Tire Quality Grading ... 5-74 Wheel Alignment and Tire Balance ... 5-75 Wheel Replacement ... 5-75 When It Is Time for New Tires ... 5-72 To Use the Engine Coolant Heater ... 2-24 Top Speed –...
Page 467 Vehicle Control ... 4-5 Damage Warnings ... iv Loading ... 4-48 Symbols ... iv Vehicle Data Collection and Event Data Records ... 7-10 Vehicle Identiﬁcation Number (VIN) ... 5-99 Service Parts Identiﬁcation Label ... 5-99 Vehicle Information Menu Item Descriptions ... 3-56 Vehicle Information Menu (Base Audio System) ...
Page 468 When You Are Ready to Leave After Parking on a Hill ... 4-60 Where to Put the Restraint ... 1-38 Why Safety Belts Work ... 1-10 Window Lockout ... 2-16 Windows ... 2-13 Power ... 2-14 Windshield Washer ... 3-16 Fluid ...

Cadillac 2004 SRX Owner's Manual

Table of Contents

Seats and Restraint Systems

Features and Controls

Section 3 Instrument Panel

Instrument Panel

Climate Controls

Maintenance Schedule

Driver Information Center (DIC)

Audio System(S)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Cadillac 2004 SRX

Summary of Contents for Cadillac 2004 SRX