Page 1: Table Of Contents
2004 Buick LeSabre Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-2 Safety Belts ... 1-6 Child Restraints ... 1-27 Air Bag Systems ... 1-47 Restraint System Check ... 1-56 Features and Controls ... 2-1 Keys ... 2-3 Doors and Locks ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem and the name LESABRE are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Page 3 Safety Warnings and Symbols You will ﬁnd a number of safety cautions in this book. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. CAUTION: These mean there is something that could hurt you or other people.
Page 4 Vehicle Damage Warnings Also, in this book you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 5 These are some examples of vehicle symbols you may ﬁnd on your vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ...1-2 Manual Seats ...1-2 Power Seats ...1-2 Manual Lumbar ...1-3 Power Lumbar ...1-3 Heated Seats ...1-4 Reclining Seatbacks ...1-4 Head Restraints ...1-6 Safety Belts ...1-6 Safety Belts: They Are for Everyone ...1-6 Questions and Answers About Safety Belts ...1-11 How to Wear Safety Belts Properly ...1-11 Driver Position ...1-12 Safety Belt Use During Pregnancy ...1-18...
Page 8: Front Seats
Front Seats Manual Seats CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving. The sudden movement could startle and confuse you, or make you push a pedal when you don’t want to.
Page 9: Manual Lumbar
Vertical Control (Option): Adjust the angle of the seatback by pressing the top of the control forward or rearward. Manual Lumbar The knob that controls this feature is located on the outboard side of each front seat. Turn the knob toward the front of the vehicle to increase lumbar support.
Page 10: Heated Seats
If you have the independent front cushion moved down as far as it will go, you may feel the lumbar support higher in your back. Readjust the location of the cushion until you are comfortable. You may also want to adjust the seatback for maximum comfort.
Page 11 But don’t have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job.
Page 12: Safety Belts
Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly.
Page 13 CAUTION: It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 14: Why Safety Belts Work
Why Safety Belts Work When you ride in or on anything, you go as fast as it goes. Put someone on it. Take the simplest vehicle. Suppose it’s just a seat on wheels.
Page 15 Get it up to speed. Then stop the vehicle. The rider doesn’t stop. The person keeps going until stopped by something. In a real vehicle, it could be the windshield...
Page 16 or the instrument panel... 1-10 or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense.
Page 17: Questions And Answers About Safety Belts
Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You could be – whether you’re wearing a safety belt or not. But you can unbuckle a safety belt, even if you’re upside down.
Page 18: Driver Position
Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”...
Page 19 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 20 What’s wrong with this? The shoulder belt is too loose. It won’t give nearly as much protection this way. 1-14 CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body.
Page 21 What’s wrong with this? The belt is buckled in the wrong place. CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 22 What’s wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-16 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 23 What’s wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 24: Safety Belt Use During Pregnancy
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 25: Center Front Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 26 When you sit in the center front seating position, you have a lap safety belt, which has no retractor. To make the belt longer, tilt the latch plate and pull it along the belt. 1-20 To make the belt shorter, pull its free end as shown until the belt is snug.
Page 27: Rear Seat Passengers
Rear Seat Passengers It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 28 If the belt stops before it reaches the buckle, tilt the 3. To make the lap part tight, pull down on the buckle latch plate and keep pulling until you can buckle it. end of the belt as you pull up on the shoulder part. Pull up on the latch plate to make sure it is secure.
Page 29 The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash this applies force to the strong pelvic bones. And you’d be less likely to slide under the lap belt. If you slid under it, the belt would apply force at your abdomen.
Page 30 Rear Safety Belt Comfort Guides for Children and Small Adults Rear shoulder belt comfort guides provide added safety belt comfort for older children who have outgrown booster seats and for small adults. When installed on a shoulder belt, the comfort guide better positions the belt away from the neck and head.
Page 31 2. Slide the guide under and past the belt. The elastic cord must be under the belt. Then, place the guide over the belt, and insert the two edges of the belt into the slots of the guide. 3. Be sure that the belt is not twisted and it lies ﬂat. The elastic cord must be under the belt and the guide on top.
Page 32: Safety Belt Extender
4. Buckle, position and release the safety belt as described in Rear Seat Passengers on page 1-21. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides.
Page 33: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 34 CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-28 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt...
Page 35: Infants And Young Children
CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 36 Every time infants and young children ride in vehicles, they should have the protection provided by appropriate restraints. Young children should not use the vehicle’s adult safety belts alone, unless there is no other choice. Instead, they need to use a child restraint. 1-30 CAUTION: People should never hold a baby in their arms...
Page 37 CAUTION: Children who are up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer outstanding protection for adults and CAUTION: (Continued) CAUTION: (Continued) older children, but not for young children and infants.
Page 38 The restraint manufacturer’s instructions that come with the restraint state the weight and height limitations for a particular child restraint. In addition, there are many kinds of restraints available for children with special needs. CAUTION: Newborn infants need complete support, including support for the head and neck.
Page 39: Child Restraint Systems
Child Restraint Systems An infant car bed (A), a special bed made for use in a motor vehicle, is an infant restraint system designed to restrain or position a child on a continuous ﬂat surface. Make sure that the infant’s head rests toward the center of the vehicle.
Page 40 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. 1-34 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness.
Page 41 How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position children. A built-in child restraint system is a permanent part of the motor vehicle. An add-on child restraint system is a portable one, which is purchased by the vehicle’s owner.
Page 42: Where To Put The Restraint
Where to Put the Restraint Accident statistics show that children are safer if they are restrained in the rear rather than the front seat. We, therefore, recommend that child restraints be secured in a rear seat, including an infant riding in a rear-facing infant seat, a child riding in a forward-facing child seat and an older child riding in a booster seat.
Page 43: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 44: Top Strap Anchor Location
Anchor the top strap to an anchor point speciﬁed in Top Strap Anchor Location on page 1-38. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed.
Page 45 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will ﬁnd anchors (A) for all three rear seating positions. This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors (A, B) and child restraint attachments to secure the restraints.
Page 46 In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. 1-40 To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback at each lower anchor position.
Page 47: Securing A Child Restraint Designed For The Latch System
CAUTION: If a LATCH-type child restraint isn’t attached to its anchorage points, the restraint won’t be able to protect the child correctly. In a crash, the child could be seriously injured or killed. Make sure that a LATCH-type child restraint is properly installed using the anchorage points, or use the vehicle’s safety belts to secure the restraint.
Page 48: Securing A Child Restraint In A Rear Seat Position
Securing a Child Restraint in a Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-39. See Top Strap on page 1-37 if the child restraint has one. CAUTION: A child in a child restraint in the center front seat can be badly injured or killed by the right...
Page 49 Tilt the latch plate to adjust the belt if needed. 3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-43...
Page 50: Securing A Child Restraint In The Right Front Seat Position
4. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you’re using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt. 5.
Page 51 Your vehicle has a right front passenger air bag. Never put a rear facing child restraint in this seat. Here is why: CAUTION: A child in a rear-facing child restraint can be seriously injured or killed if the right front passenger’s air bag inﬂates.
Page 52 5. Pull the rest of the lap belt all the way out of the retractor to set the lock. 1-46 6. To tighten the belt, feed the lap belt back into the retractor while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 53: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has a frontal air bag for the driver and a frontal air bag for the right front passenger. Your vehicle may also have a side impact air bag for the driver, and another side impact air bag for the right front passenger.
Page 54 Here are the most important things to know about the air bag systems: CAUTION: You can be severely injured or killed in a crash if you aren’t wearing your safety belt – even if you have air bags. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it.
Page 55 CAUTION: Anyone who is up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them.
Page 56: Where Are The Air Bags
Where Are the Air Bags? The driver’s frontal air bag is in the middle of the steering wheel. 1-50 The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. If your vehicle has one, the driver’s side impact air bag is in the side of the driver’s seatback closest to the door.
Page 57: When Should An Air Bag Inﬂate
If your vehicle has one, the right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door. CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death.
Page 58 In addition, your vehicle has “dual stage” frontal air bags, which adjust the amount of restraint according to crash severity. For moderate frontal impacts, these air bags inﬂate at a level less than full deployment. For more severe frontal impacts, full deployment occurs. If the front of your vehicle goes straight into a wall that does not move or deform, the threshold level for the reduced deployment is about 10 to 16 mph (18 to...
Page 59: What Makes An Air Bag Inﬂate
What Makes an Air Bag Inﬂate? In an impact of sufficient severity, the air bag sensing system detects that the vehicle is in a crash. For both frontal and side impact air bags, the sensing system triggers a release of gas from the inﬂator, which inﬂates the air bag.
Page 60 What Will You See After an Air Bag Inﬂates? After the air bag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the air bag inﬂated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal air bag and the instrument panel for the right front passenger’s frontal air bag.
Page 61 In many crashes severe enough to inﬂate an air bag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger air bag. • Air bags are designed to inﬂate only once. After an air bag inﬂates, you’ll need some new parts for your air bag system.
Page 62: Restraint System Check
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems.
Page 63: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 64 NOTES 1-58...
Page 65: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-5 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-9 Door Locks ...2-9 Central Door Unlocking System ...2-10 Power Door Locks ...2-10 Door Ajar Reminder ...2-11 Delayed Locking ...2-11 Programmable Automatic Door Locks ...2-12 Rear Door Security Locks ...2-13 Lockout Protection ...2-13 Leaving Your Vehicle ...2-13...
Page 66 Section 2 ® OnStar System ...2-37 ® HomeLink Transmitter ...2-38 ® Programming the HomeLink Transmitter ...2-39 Storage Areas ...2-42 Glove Box ...2-42 Center Console Storage Area ...2-42 Convenience Net ...2-42 Features and Controls Sunroof ...2-43 Vehicle Personalization ...2-44 Memory Seat and Mirrors ...2-44...
Page 67: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Do not leave the keys in a vehicle with children.
Page 68 There is a master key that works in all of the lock cylinders (driver’s door, trunk, ignition, and glove box). There is also a VALET key which operates only the driver’s door and the ignition. ® Your vehicle has the PASS-Key system.
Page 69: Remote Keyless Entry System
Remote Keyless Entry System Your keyless entry system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 70: Personalization Features
If your vehicle is equipped with the DIC, the numbers on the back of your transmitter correspond to DRIVER #1 and DRIVER #2 on the DIC. For more information see Driver Information Center (DIC) on page 3-45. button to unlock the driver’s door.
Page 71: Security Feedback
• Delayed Locking: This feature allows for a ﬁve second delay in locking the doors after the closing of the last door. • Perimeter Lighting: This feature provides for the daytime running lamps (DRL), parking lamps and the back-up lamps to turn on when the unlock button on the remote keyless entry transmitter is pressed.
Page 72: Battery Replacement
4. Press the trunk button again. Each time the trunk button is pressed, the security feedback will advance to the next mode, and the horn will chirp. 5. Release the power door lock switch. The security feedback will remain in the most current mode selected.
Page 73: Doors And Locks
To replace the battery, do the following: 1. Insert a coin, or similar object, into the notch near the key ring. Turn it counterclockwise to separate the two halves of the transmitter. 2. Once the transmitter is separated, use a pencil eraser to remove the old battery.
Page 74: Central Door Unlocking System
There are several ways to lock and unlock your vehicle. If your vehicle has a content theft-deterrent system, unlock the doors only with the key or remote keyless entry system. This will avoid setting off the alarm. To unlock the door from the outside, use your door key or remote keyless entry transmitter.
Page 75: Door Ajar Reminder
Door Ajar Reminder If your vehicle is equipped with the Driver Information Center (DIC), and a door is not fully closed, the DIC will display a DOOR AJAR message. See Driver Information Center (DIC) on page 3-45. Delayed Locking This feature lets the driver delay the actual locking of the vehicle.
Page 76: Programmable Automatic Door Locks
Programmable Automatic Door Locks Close the doors and turn on the ignition. Every time you move the shift lever out of PARK (P), all of the doors will lock. And, every time you stop and move the shift lever into PARK (P), the doors will unlock. If someone needs to get out while you’re not in PARK (P), have that person use the manual door lock control or power door lock switch.
Page 77: Lockout Protection
Rear Door Security Locks Your vehicle is equipped with rear door security locks that prevent passengers from opening the rear doors of your vehicle from the inside. To use one of these locks, do the following: 1. Open the rear door you want to lock. 2.
Page 78: Trunk Lock Release
Trunk CAUTION: It can be dangerous to drive with the trunk lid open because carbon monoxide (CO) gas can come into your vehicle. You can’t see or smell CO. It can cause unconsciousness and even death. If you must drive with the trunk lid open or if electrical wiring or other cable connections must pass through the seal between the body and the trunk lid:...
Page 79: Trunk Security Override
Trunk Security Override The remote keyless entry transmitter will unlock the trunk even if the trunk release lockout switch is in LOCK. Emergency Trunk Release Handle Notice: Using the emergency trunk release handle as a tie-down or anchor point when securing items in the trunk may damage it.
Page 80: Windows
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 81: Power Windows
Power Windows The power window controls located on the driver’s door armrest operate each of the windows while the ignition is on or while Retained Accessory Power (RAP) is active. In addition, each passenger door has a control for its own window. See “Retained Accessory Power (RAP)”...
Page 82: Theft-Deterrent Systems
Theft-Deterrent Systems Vehicle theft is big business, especially in some cities. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have a content theft-deterrent alarm system.
Page 83: Testing The Alarm
Testing the Alarm The alarm can be tested by following these steps: 1. From inside the vehicle, roll down the driver’s window and open the driver’s door. 2. Activate the system by locking the doors with the power door lock switch while the door is open, or with the remote keyless entry transmitter.
Page 84 ® PASS-Key III Operation Your vehicle is equipped with the PASS-Key (Personalized Automotive Security System) theft-deterrent system. PASS-Key theft-deterrent system. This means you don’t have to do anything different to arm or disarm the system. It works when you insert or remove the key from the ignition.
Page 85: Starting And Operating Your Vehicle
4. Insert the key to be programmed and turn it to RUN within 10 seconds of removing the previous key. 5. The SECURITY telltale light will turn off once the key has been programmed. It may not be apparent that the SECURITY light went on due to how quickly the key is programmed.
Page 86: Ignition Positions
Ignition Positions With the key in the ignition switch, you can turn to ﬁve different positions. (A) ACCESSORY: This position lets you use your electrical accessories such as power windows, power sunroof (if equipped), radio and the windshield wipers. To use, push in the ignition key and turn it toward you.
Page 87: Key Reminder Warning
Key Reminder Warning If you leave your key in OFF, you will hear a warning chime when you open the driver’s door. Always leave your key in LOCK while the engine is off. If you leave it in any other position, you will drain your battery power.
Page 88: Engine Coolant Heater
Notice: Your engine is designed to work with the electronics in your vehicle. If you add electrical parts or accessories, you could change the way the engine operates. Before adding electrical equipment, check with your dealer. If you do not, your engine might not perform properly.
Page 89: Automatic Transaxle Operation
Automatic Transaxle Operation Your automatic transaxle has a shift lever located on the steering column. PARK (P): This position locks your front wheels. It’s the best position to use when you start your engine because your vehicle can’t move easily. CAUTION: It is dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the...
Page 90 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped.
Page 91: Parking Brake
SECOND (2): This position gives you more power but lower fuel economy than THIRD (3). You can use SECOND (2) on hills. It can help control your speed as you go down steep mountain roads, but then you would also want to use your brakes off and on. Notice: Driving in SECOND (2) for more than 25 miles (40 km) or at speeds over 55 mph (90 km/h) may damage the transaxle.
Page 92: Shifting Into Park (P)
Notice: Driving with the parking brake on can overheat the brake system and cause premature wear or damage to brake system parts. Verify that the parking brake is fully released and the brake warning light is off before driving. If you are towing a trailer and are parking on any hill, see Towing a Trailer on page 4-39.
Page 93: Leaving Your Vehicle With The Engine Running
• Move the lever up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). Leaving Your Vehicle With the Engine Running CAUTION:...
Page 94: Torque Lock
Torque Lock If you are parking on a hill and you don’t shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 95: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell.
Page 96: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 97: Mirrors
Mirrors Manual Rearview Mirror When you are sitting in a comfortable driving position, adjust the mirror so you can see clearly behind your vehicle. Grip the mirror in the center to move it up or down and side to side. The day/night adjustment allows you to adjust the mirror to avoid glare from any headlamps behind you.
Page 98: Compass Variance
Mirror Operation MIRROR: Press this button to turn on the automatic dimming feature. Press it again to turn off the automatic dimming feature. (On/Off): For mirrors equipped with OnStar controls, press and hold this button for several seconds to turn on the automatic dimming feature. Press and hold it again to turn the automatic dimming feature off.
Page 99: Outside Power Mirrors
2. Press and hold COMPASS (or the on/off button for ® mirrors equipped with OnStar zone number appears in the display. 3. Once a zone number appears in the display, press the COMPASS button (or the on/off button for ® mirrors equipped with OnStar the correct zone number appears in the display.
Page 100: Outside Curb View Assist Mirror
The mirrors may also have an arrow that ﬂashes when the turn signal is used. See Turn Signal/Multifunction Lever on page 3-7. Outside Curb View Assist Mirror If you have the Memory Seat and Mirrors feature, the passenger’s outside rearview mirror includes a tilt-down feature that operates when the shift lever is in REVERSE (R).
Page 101: Onstar System
® OnStar System Your vehicle may have this feature. OnStar global positioning system (GPS) satellite technology, wireless communications, and state of the art call centers to provide you with a wide range of safety, security, information and convenience services. ® A complete OnStar user’s guide and the terms and ®...
Page 102: Homelink Transmitter
Luxury and Leisure Plan • All Directions and Connections Plan services • Personal Concierge ® OnStar Personal Calling ® With OnStar Personal Calling, you have a safer way to stay connected while driving. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts and no additional roaming charges.
Page 103 If your vehicle is equipped with the HomeLink Transmitter, it complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 104 2. Position the end of your hand-held transmitter about 1 to 3 inches (3 to 8 cm) away from the ® HomeLink buttons while keeping the indicator light in view. 3. Simultaneously press and hold both the desired ® button on HomeLink and the hand-held transmitter button.
Page 105: Gate Operator And Canadian Programming
Gate Operator and Canadian Programming Canadian radio-frequency laws require transmitter signals to “time out” or quit after several seconds of transmission. This may not be long enough for ® HomeLink to pick up the signal during programming. Similarly, some U.S. gate operators are manufactured to “time out”...
Page 106: Storage Areas
Resetting Defaults ® To reset HomeLink to default settings do the following: 1. Hold down the two outside buttons for about 20 seconds until the indicator light begins to ﬂash. 2. Continue to hold both buttons until the HomeLink indicator light turns off. 3.
Page 107: Sunroof
Sunroof Your vehicle may be equipped with a sunroof. The sunroof has both manual and express features for opening the glass panel and sunshade. The switch for the sunroof is located on the headliner between the sun visors. The sunroof switch has a number of positions that control the sunroof movement.
Page 108: Vehicle Personalization
Vehicle Personalization Memory Seat and Mirrors If your vehicle has this feature, the controls are located on the driver’s door panel, and are used to program and recall memory settings for the driver’s seating, outside mirror positions and climate controls. See Climate Control System on page 3-24 for more information.
Page 109 To set the seat and mirror positions for a second driver, follow the previous steps, but start by pressing the unlock button on the transmitter that displays the other DRIVER # on the DIC. Be sure to use the MEMORY button which corresponds to the DRIVER # identiﬁed by the second transmitter.
Page 110 NOTES 2-46...
Page 111: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-6 Horn ...3-7 Tilt Wheel ...3-7 Turn Signal/Multifunction Lever ...3-7 Exterior Lamps ...3-14 Interior Lamps ...3-17 Head-Up Display (HUD) ...3-20 Accessory Power Outlets ...3-22 Ashtrays and Cigarette Lighter ...3-23 Climate Controls ...3-24 Climate Control System ...3-24 Dual Automatic Climate Control System ...3-26...
Page 112 Section 3 Audio System(s) ...3-55 Setting the Time ...3-55 Radio with CD ...3-56 Radio with Cassette and CD ...3-62 Trunk-Mounted CD Changer ...3-73 Personal Choice Radio Controls ...3-77 Theft-Deterrent Feature ...3-78 Audio Steering Wheel Controls ...3-78 Instrument Panel Understanding Radio Reception ...3-79 Care of Your Cassette Tape Player ...3-80 Care of Your CDs ...3-81 Care of Your CD Player ...3-81...
Page 113 NOTES...
Page 114: Instrument Panel Overview
Instrument Panel Overview...
Page 115 The main components of your instrument panel are the following: A. Air Outlets. See Outlet Adjustment on page 3-30. B. Driver Information Center (DIC) Buttons (If Equipped). See DIC Controls and Displays on page 3-46. C. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-7.
Page 116: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column.
Page 117: Turn Signal/Multifunction Lever
Horn Press the center area of the steering wheel to sound the horn. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive. You can also raise it to the highest level to give your legs more room when you exit and enter the vehicle.
Page 118: Turn And Lane-Change Signals
Turn and Lane-Change Signals To signal a turn, move the lever on the left side of the steering wheel all the way up or down. The lever returns automatically when the turn is complete. An arrow on the instrument panel cluster will ﬂash in the direction of the turn or lane change.
Page 119: Windshield Wipers
Flash-To-Pass This feature lets you use the high-beam headlamps to signal the driver in front of you that you want to pass. It works even if your headlamps are off. Pull the turn signal lever toward you brieﬂy to ﬂash-to-pass. If the headlamps are off or on low beam, the high-beam headlamps will turn on.
Page 120: Windshield Washer
The system will operate in the delay, low speed and high speed modes. If the system is left on for long periods of time, occasional wipes may occur without any moisture on the windshield. This is normal and indicates that the Rainsense™ system is active. The Rainsense™...
Page 121: Cruise Control
Cruise Control The switches to operate cruise control are located on the steering wheel. With cruise control, you can maintain a speed of about 25 mph (40 km/h) or more without keeping your foot on the accelerator. This is helpful on long trips. Cruise control does not work at speeds below about 25 mph (40 km/h).
Page 122 Setting Cruise Control CAUTION: If you leave your cruise control on when you are not using cruise, you might hit a button and go into cruise when you do not want to. You could be startled and even lose control. Keep the cruise control switch off until you want to use cruise control.
Page 123 Increasing Speed While Using Cruise Control There are two ways to go to a higher speed: • Use the accelerator pedal to get to the higher speed. Press SET/COAST, then release it and the accelerator pedal. You will now cruise at the higher speed.
Page 124: Exterior Lamps
Exterior Lamps The exterior lamp control buttons are located to the left of the steering column. < (Parking Lamps): Press this button to turn on the parking lamps, together with the following: • Sidemarker Lamps • Taillamps • License Plate Lamps •...
Page 125: Daytime Running Lamps
Daytime Running Lamps Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
Page 126: Twilight Sentinel
® Twilight Sentinel ® Twilight Sentinel turns your headlamps on and off by sensing how dark it is outside. The lever for this feature is located to the left of the steering column. To operate it, leave the exterior lamp button off. If you slide the lever all the way to MAX, your headlamps will remain on for about three minutes after you turn off your engine.
Page 127: Exterior Lighting Battery Saver
Exterior Lighting Battery Saver If the exterior lamp button has been left on, the exterior lamps will turn off about 10 minutes after the ignition is turned to LOCK and a door has been opened. This protects against draining the battery in case you have accidentally left the headlamps or parking lamps on.
Page 128: Courtesy Lamps
Courtesy Lamps If it is dark enough outside, when any door is opened, several lamps go on. They make it easy for you to enter and leave the vehicle. You can also turn these lamps on by sliding the INTERIOR lever all the way to the top. Entry Lighting If it is dark enough outside when you press the unlock button on the remote keyless entry transmitter, the...
Page 129: Front Reading Lamps
3. Press the instant alarm on the transmitter. Perimeter lighting remains on at this time and the horn will chirp two times. 4. Press the instant alarm on the transmitter again. Perimeter lighting is disabled and the horn will chirp one time. 5.
Page 130: Battery Load Management
Battery Load Management The battery load management feature is designed to monitor the vehicle’s electrical load and determine when the battery is in a heavy discharge condition. During times of high electrical loading, the engine may idle at a higher RPM setting than normal to make sure the battery charges.
Page 131 The HUD shows these images when they are lighted on the instrument panel cluster. Be sure to continue scanning your displays, controls and driving environment just as you would in a vehicle without HUD. If you never look at your instrument panel cluster, you may not see something important, such as a warning light.
Page 132: Accessory Power Outlets
3. Now press the image height adjuster switch to position the image as low as possible, while still keeping it in full view. 4. Slide the dimmer lever downward until the HUD image is no brighter than necessary. To turn the HUD display off, slide the dimmer lever all the way down.
Page 133: Ashtrays And Cigarette Lighter
Notice: Leaving electrical equipment on for extended periods will drain the battery. Always turn off electrical equipment when not in use and do not plug in equipment that exceeds the maximum amperage rating. Certain electrical accessories may not be compatible to the accessory power outlets and could result in blown vehicle or adapter fuses.
Page 134: Climate Controls
Climate Controls Climate Control System With this system you can control the heating, cooling and ventilation for your vehicle. TEMPERATURE: This lever is used to adjust the temperature of the air coming through the system. Moving the lever between COOL and WARM will change the temperature of the air coming through your outlets.
Page 135: Defogging And Defrosting
Also in this mode, the RECIRC function is activated to create the maximum cooling effect in the vehicle. If RECIRC was activated before selecting MAX, the light in the RECIRC button will go off. If RECIRC is selected after MAX, the light in the RECIRC button will not come on.
Page 136: Rear Window Defogger
FRONT (Defrost): Pressing this button directs most of the air to the windshield and the outboard outlets (for the side windows), with some air directed to the ﬂoor outlets. In this mode, the system will automatically turn off recirculation and run the air conditioning compressor, unless the outside temperature is at or below freezing.
Page 137: Automatic Operation
Automatic Operation AUTO (Automatic): Press the AUTO button for automatic control of the inside temperature, the air delivery mode and the fan speed. 1. Press the AUTO button. 2. Adjust the temperature to 75° F (24° C). Choosing the coldest or warmest temperature setting will not cause the system to heat or cool any faster.
Page 138 Use the up and down arrows on the AIR FLOW button to cycle through the available modes. • WINDSHIELD-FLOOR: This mode directs most of the airﬂow to the windshield with some airﬂow to the outboard outlets (for the side windows) and the ﬂoor outlets.
Page 139 Sensors The solar sensor on your vehicle monitors the solar radiation and the air inside of your vehicle, then uses the information to maintain the selected temperature by initiating needed adjustments to the temperature, the fan speed and the air delivery system. The system may also supply cooler air to the side of the vehicle facing the sun.
Page 140 Passenger Temperature Control If your vehicle has this feature, then the driver and the front-seat passenger can select separate temperature settings. This feature allows the passenger to select a temperature that is 5° F (3° C) warmer or cooler than the driver’s selected temperature.
Page 141: Climate Controls Personalization
Operation Tips • Clear away any ice, snow or leaves from the air inlets at the base of the windshield that may block the ﬂow of air into your vehicle. • Use of non-GM approved hood deﬂectors may adversely affect the performance of the system. •...
Page 142: Warning Lights, Gages And Indicators
To recall the climate control settings last stored on your transmitter, press the unlock button on your remote keyless entry transmitter and put the ignition in ACCESSORY or RUN. The settings will be recalled. Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle.
Page 143: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. Your vehicle is equipped with one of these instrument panel clusters, which includes indicator warning lights and gages that are explained on the following pages.
Page 144 Cluster With Tachometer (United States version shown, Canada similar) 3-34...
Page 145: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles or kilometers. Press the ENG/MET button which is located to the left of the speedometer to change from mph to km/h.
Page 146: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to RUN or START, a chime will come on for several seconds to remind people to fasten their safety belts. The safety belt light will also come on and stay on for several seconds, then ﬂash for several more.
Page 147 The air bag readiness light should ﬂash for a few seconds when you turn the ignition key to RUN. If the light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem. Battery Warning Light When you turn the key to RUN, this light will turn on...
Page 148: Anti-Lock Brake System Warning Light
When the ignition is on, the brake system warning light will also come on when you set your parking brake. The light will stay on if your parking brake doesn’t release fully. If you try to drive off with the parking brake set, a chime will also come on until you release the parking brake.
Page 149 Traction Control System (TCS) Warning Light For vehicles equipped with the traction control system, this warning light should come on brieﬂy when the engine is started. If the warning light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there’s a problem. If it stays on, or comes on when you’re driving, there may be a problem with your traction control system and your vehicle may need service.
Page 150: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage This gage shows the engine coolant temperature. If the pointer moves into the shaded area, the engine is too hot. Standard version shown, uplevel similar A temperature indicator light will turn on and a chime will sound. If you have been operating your vehicle under normal driving conditions, and the temperature indicator light comes on, you should pull off the road, stop your...
Page 151: If The Light Is Flashing
Notice: Modiﬁcations made to the engine, transaxle, exhaust, intake or fuel system of your vehicle or the replacement of the original tires with other than those of the same Tire Performance Criteria (TPC) can affect your vehicle’s emission controls and may cause this light to come on. Modiﬁcations to these systems could lead to costly repairs not covered by your warranty.
Page 152: If The Light Is On Steady
If the Light Is On Steady You may be able to correct the emission system malfunction by considering the following: Did you recently put fuel into your vehicle? If so, reinstall the fuel cap, making sure to fully install the cap. See Filling Your Tank on page 5-7. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 153: Maintenance Schedule
Your vehicle will not pass this inspection if the OBD (on-board diagnostic) system determines that critical emission control systems have not been completely diagnosed by the system. The vehicle would be considered not ready for inspection. This can happen if you have recently replaced your battery or if your battery has run down.
Page 154: Security Light
Security Light Your vehicle may have a content theft-deterrent alarm system. With this system, the SECURITY light will ﬂash as you open the door if your ignition is off. For more information see Content Theft-Deterrent on page 2-18. Cruise Control Light The CRUISE light comes on when you set the vehicle’s cruise control.
Page 155: Fuel Gage
Fuel Gage United States The fuel gage shows about how much fuel is in your tank. It works only when the ignition is on. When the indicator moves to the edge of the low fuel warning band, the low fuel warning light will come on and a chime will sound.
Page 156: Dic Controls And Displays
DIC Controls and Displays When you turn the ignition on, the DIC will display your DRIVER NUMBER. You can have your dealer program your name to appear on this display line. See your dealer for more information. The system will then perform a status check and display any messages if a problem is detected.
Page 157 FUEL INFO (Information): Press this button to display fuel information. Press the FUEL INFO button until the display shows FUEL ECONOMY AVERAGE. Average fuel economy is viewed as a long term approximation of your overall driving conditions. To learn the average fuel economy from a new starting point, press the RESET button while the average fuel economy is displayed in the DIC.
Page 158 Press the GAGE INFO button until OIL LIFE INDEX appears in the display. The OIL LIFE INDEX NORMAL display will show an estimate of the oil’s remaining useful life. When the oil life index is less than 10 percent, the display will show OIL LIFE INDEX CHANGE OIL. When you have the oil changed according to the maintenance schedule, you will have to reset the oil life monitor.
Page 159: Service
DIC Warnings and Messages Other messages or warnings may appear in the DIC display. For Canadian drivers, in addition to the DIC message your DIC will display EXP with a number after it which reﬂects the following messages: (Export ID) Warning Message TURN SIGNAL STILL ON? TRUNK AJAR WINDSHIELD WASHER FLUID LOW...
Page 160: Dic Vehicle Personalization
3. Press and hold the ENG/MET button for ﬁve seconds. WELCOME TO BUICK OPTION FEATURE will appear in the display. 4. The ﬁrst choice to be made will be DRIVER ID 1 or 2.
Page 161: Automatic Door Locks
If you would like to exit the selection mode without moving through each of the personal choice features, simply press a different button on the DIC or turn off the ignition. Whatever personal choices you made will still be retained, even without passing through each of the features.
Page 162 Window Lock Out The number of passenger windows locked out by the window LOCK switch can be programmed through the DIC. If you choose R + PASS, all three passenger window switches will be inactive when the window LOCK switch is enabled.
Page 163: Exterior Lights
If you choose ON for KEYLESS FEEDBACK and ON for HORN FEEDBACK, your horn will chirp when all doors are unlocked and when locking your vehicle. If you choose ON for KEYLESS, LIGHTS and HORN FEEDBACK, your exterior lamps will ﬂash twice at the ﬁrst unlock button press, your exterior lamps will ﬂash twice and the horn will chirp once at the second unlock button press, and the exterior lamps will ﬂash and...
Page 164: Memory Seats
Memory Seats If your vehicle has this feature, the memory seat and mirror positions will be recalled for the identiﬁed driver when the remote keyless entry transmitter is used to enter the vehicle. You can program this feature to be active by choosing ON when the SEAT RECALL choice appears, or inactive by choosing OFF when the SEAT RECALL choice appears on the DIC.
Page 165: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle – like a tape player, CB radio, mobile telephone or two-way radio – be sure you can add what you want. If you can, it’s very important to do it properly.
Page 166: Radio With Cd
Radio with CD Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. DISP (Display): Press this button to switch the display between the radio station frequency and the time. The time can be displayed with the ignition on or off.
Page 167: Setting Preset Stations
To scan preset stations, press and hold one of the SEEK arrows for more than four seconds until PSCAN and the preset number appear on the display. You will hear a double beep. The radio will go to the ﬁrst preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station.
Page 168: Using Rds
To adjust the fade between the front and the rear speakers, push and release AUDIO until FADE appears on the display. Then turn the AUDIO knob to move the sound toward the front or the rear speakers. A bar graph with indicators will show how the sound is balanced between the front and rear speakers.
Page 169: Finding A Pty Station
Finding a PTY Station To select and ﬁnd a desired PTY perform the following: 1. Press P-TYP. The PTY symbol will be displayed on the screen. 2. Select a category by turning the AUDIO knob. 3. Once the desired category is displayed, press either SEEK arrow to select the category and take you to the category’s ﬁrst station.
Page 170: Radio Messages
INFO (Information): If the current station has a message, INFO will appear on the display. Press this button to see the message. The message may display the artist and song title, call in phone numbers, etc. If the whole message is not displayed, parts of it will appear every three seconds.
Page 171 If playing a CD-R the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled. You may experience an increase in skipping, difficulty in ﬁnding tracks, and/or difficulty in loading and ejecting.
Page 172: Radio With Cassette And Cd
Compact Disc Messages CHECK CD: If this message appears on the radio display, it could be due to one of the following reasons: • You’re driving on a very rough road. When the road is smoother, the disc should play. •...
Page 173: Playing The Radio
This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 174: Finding A Station
Finding a Station BAND: Press this button to switch between FM1, FM2, or AM, XM1 or XM2 (USA only, if equipped). The display will show your selection. TUNE: Turn this knob to choose a radio station. © ¨ SEEK : Press the right or the left arrow to go to the next or to the previous station and stay there.
Page 175: Setting The Tone (Bass/Treble)
Setting the Tone (Bass/Treble) AUDIO: Push and release AUDIO until BASS, MID, or TREBLE appears on the display. Then turn the AUDIO knob to increase or to decrease. If a station is weak or noisy, you may want to decrease the treble. To adjust bass, midrange or treble to the middle position, select BASS, MID, or TREBLE.
Page 176: Finding A Pty Station (Rds And Xm)
Finding a PTY Station (RDS and XM™) To select and ﬁnd a desired PTY perform the following: 1. Press P-TYP. The P-TYPE symbol will be displayed on the screen. 2. Select a category by turning the AUDIO knob. 3. Once the desired category is displayed, press either SEEK arrow to select the category and take you to the category’s ﬁrst station.
Page 177 ALERT! will not be affected by tests of the emergency broadcast system. This feature is not supported by all RDS stations. INFO (Information): If the current station has a message, INFO will appear on the display. Press this button to see the message. The message may display the artist and song title, call in phone numbers, etc.
Page 178 Radio Display Message XL (Explicit Language XL on the radio display, Channels) after the channel name, indicates content with explicit language. Updating Updating encryption code No Signal Loss of signal Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no longer...
Page 179 Radio Display Message No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr...
Page 180: Playing A Cassette Tape
Playing a Cassette Tape The longer side with the tape visible should face to the right. If the ignition and the radio are on, the tape can be inserted and will begin playing. If you hear nothing or hear a garbled sound, the tape may not be in squarely.
Page 181: Cassette Tape Messages
Cassette Tape Messages If an error message appears while trying to play a cassette tape, it could be for one of the following reasons: • TIGHT TAPE: The tape is tight and the player can’t turn the tape hubs. Remove the tape. Hold the tape with the open end down and try to turn the right hub counterclockwise with a pencil.
Page 182 The integral CD player can play the smaller 8 cm single discs with an adapter ring. Full-size compact discs and the smaller discs are loaded in the same manner. If playing a CD-R the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled.
Page 183: Trunk-Mounted Cd Changer
Compact Disc Messages CHECK CD: If this message appears on the radio display, it could be due to one of the following reasons: • You’re driving on a very rough road. When the road becomes smoother, the disc should play. •...
Page 184 You must ﬁrst load the magazine with discs before you can play a compact disc. Each of the 12 trays holds one disc. Slide the button on the top of the magazine and gently pull out one of the trays. Load the trays from top to bottom, placing a disc on the tray label side up.
Page 185 Close the door by sliding it all the way to the right. When the door is closed, the changer will begin checking for discs in the magazine. This will continue for up to one and a half minutes depending on the number of discs loaded.
Page 186 4 RDM (Random): Press this pushbutton to enter the random play mode. RAND will appear on the display. While in this mode, tracks and discs will be played in random, rather than sequential, order. Press this pushbutton again to turn off the random feature and return to normal operation.
Page 187: Compact Disc Errors
Compact Disc Errors E (Error): If this message and a number appear on the display, an error has occurred. If the error occurred while trying to play a CD in the compact disc player or changer, the following conditions may have caused the error: •...
Page 188: Theft-Deterrent Feature
Theft-Deterrent Feature ® THEFTLOCK is designed to discourage theft of your radio. It works by using a secret code to disable all radio functions whenever battery power is removed and the radio is placed in a different vehicle. This feature requires no user input to be activated.
Page 189: Understanding Radio Reception
SCAN: Press this button to scan your radio preset stations. The radio will scan to the ﬁrst preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station. The radio will scan preset stations with a strong signal only.
Page 190: Care Of Your Cassette Tape Player
Care of Your Cassette Tape Player A tape player that is not cleaned regularly can cause reduced sound quality, ruined cassettes, or a damaged mechanism. Cassette tapes should be stored in their cases away from contaminants, direct sunlight, and extreme heat. If they are not, they may not operate properly or they may cause failure of the tape player.
Page 191: Care Of Your Cds
Care of Your CDs Handle CDs carefully. Store them in their original cases or other protective cases and away from direct sunlight and dust. If the surface of a CD is soiled, dampen a clean, soft cloth in a mild, neutral detergent solution and clean it, wiping from the center to the edge.
Page 192: Xm™ Satellite Radio Antenna System (48 Contiguous Us States)
If, when you turn on your rear window defogger, you hear static on your radio station, it could mean that a defogger grid line has been damaged. If this is true, the grid line must be repaired. If you choose to add an aftermarket cellular telephone to your vehicle, and the antenna needs to be attached to the glass, be sure that you do not damage the grid lines for the AM-FM antennas or place the cellular...
Page 193: Driving Your Vehicle
Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Defensive Driving ...4-2 Drunken Driving ...4-2 Control of a Vehicle ...4-5 Braking ...4-6 Traction Control System (TCS) ...4-9 Steering ...4-10 Off-Road Recovery ...4-13 Passing ...4-13 Loss of Control ...4-15 Driving at Night ...4-16 Driving in Rain and on Wet Roads ...4-17 City Driving ...4-20 Driving Your Vehicle...
Page 194: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Defensive Driving The best advice anyone can give about driving is: Drive defensively. Please start with a very important safety device in your vehicle: Buckle up. See Safety Belts: They Are for Everyone on page 1-6. Defensive driving really means “be ready for anything.”...
Page 195 Police records show that almost half of all motor vehicle-related deaths involve alcohol. In most cases, these deaths are the result of someone who was drinking and driving. In recent years, more than 16,000 annual motor vehicle-related deaths have been associated with the use of alcohol, with more than 300,000 people injured.
Page 196 It is the amount of alcohol that counts. For example, if the same person drank three double martinis (3 ounces or 90 ml of liquor each) within an hour, the person’s BAC would be close to 0.12 percent. A person who consumes food just before or during drinking will have a somewhat lower BAC level.
Page 197: Control Of A Vehicle
CAUTION: Drinking and then driving is very dangerous. Your reﬂexes, perceptions, attentiveness and judgment can be affected by even a small amount of alcohol. You can have a serious — or even fatal — collision if you drive after drinking. Please do not drink and drive or ride with a driver who has been drinking.
Page 198: Braking
Braking Braking action involves perception time and reaction time. First, you have to decide to push on the brake pedal. That is perception time. Then you have to bring up your foot and do it. That is reaction time. Average reaction time is about 3/4 of a second. But that is only an average.
Page 199: Anti-Lock Brake System (Abs)
Anti-lock Brake System (ABS) Your vehicle has anti-lock brakes. ABS is an advanced electronic braking system that will help prevent a braking skid. When you start your engine, or when you begin to drive away, your anti-lock brake system will check itself. You may hear a momentary motor or clicking noise while this test is going on, and you may even notice that your brake pedal moves or pulses a little.
Page 200: Braking In Emergencies
The anti-lock system can change the brake pressure faster than any driver could. The computer is programmed to make the most of available tire and road conditions. This can help you steer around the obstacle while braking hard. As you brake, your computer keeps receiving updates on wheel speed and controls braking pressure accordingly.
Page 201: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 202: Steering
To turn the system off, press the TRACTION OFF button located at the end of the shift lever on the right side of the steering wheel. The traction control system warning light will come on and stay on. If the system is limiting wheel spin when you press the button, the warning light will come on —...
Page 203 The traction you can get in a curve depends on the condition of your tires and the road surface, the angle at which the curve is banked, and your speed. While you are in a curve, speed is the one factor you can control.
Page 204: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 205: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 206 • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 207: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Page 208: Driving At Night
Driving at Night Night driving is more dangerous than day driving. One reason is that some drivers are likely to be impaired — by alcohol or drugs, with night vision problems, or by fatigue. Here are some tips on night driving. •...
Page 209: Driving In Rain And On Wet Roads
You can be temporarily blinded by approaching headlamps. It can take a second or two, or even several seconds, for your eyes to readjust to the dark. When you are faced with severe glare (as from a driver who does not lower the high beams, or a vehicle with misaimed headlamps), slow down a little.
Page 210 The heavier the rain, the harder it is to see. Even if your windshield wiper blades are in good shape, a heavy rain can make it harder to see road signs and traffic signals, pavement markings, the edge of the road and even people walking.
Page 211: Driving Through Deep Standing Water
CAUTION: Wet brakes can cause accidents. They will not work as well in a quick stop and may cause pulling to one side. You could lose control of the vehicle. After driving through a large puddle of water or a car wash, apply your brake pedal lightly until your brakes work normally.
Page 212: Driving Through Flowing Water
Driving Through Flowing Water CAUTION: Flowing or rushing water creates strong forces. If you try to drive through ﬂowing water, as you might at a low water crossing, your vehicle can be carried away. As little as six inches of ﬂowing water can carry away a smaller vehicle.
Page 213: Freeway Driving
Here are ways to increase your safety in city driving: • Know the best way to get to where you are going. Get a city map and plan your trip into an unknown part of the city just as you would for a cross-country trip.
Page 214: Before Leaving On A Long Trip
At the entrance, there is usually a ramp that leads to the freeway. If you have a clear view of the freeway as you drive along the entrance ramp, you should begin to check traffic. Try to determine where you expect to blend with the ﬂow.
Page 215: Highway Hypnosis
Here are some things you can check before a trip: • Windshield Washer Fluid: Is the reservoir full? Are all windows clean inside and outside? • Wiper Blades: Are they in good shape? • Fuel, Engine Oil, Other Fluids: Have you checked all levels? •...
Page 216: Hill And Mountain Roads
Hill and Mountain Roads Driving on steep hills or mountains is different from driving in ﬂat or rolling terrain. 4-24 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable.
Page 217: Winter Driving
CAUTION: Coasting downhill in NEUTRAL (N) or with the ignition off is dangerous. Your brakes will have to do all the work of slowing down. They could get so hot that they would not work well. You would then have poor braking or even none going down a hill.
Page 218: Driving On Snow Or Ice
Include an ice scraper, a small brush or broom, a supply of windshield washer ﬂuid, a rag, some winter outer clothing, a small shovel, a ﬂashlight, a red cloth and a couple of reﬂective warning triangles. And, if you will be driving under severe conditions, include a small bag of sand, a piece of old carpet or a couple of burlap bags to help provide traction.
Page 219 the least traction of all. You can get wet ice when it’s about freezing (32°F; 0°C) and freezing rain begins to fall. Try to avoid driving on wet ice until salt and sand crews can get there. Whatever the condition – smooth ice, packed, blowing or loose snow –...
Page 220: If You're Caught In A Blizzard
If You’re Caught in a Blizzard If you are stopped by heavy snow, you could be in a serious situation. You should probably stay with your vehicle unless you know for sure that you are near help and you can hike through the snow. 4-28 Here are some things to do to summon help and keep yourself and your passengers safe:...
Page 221 CAUTION: Snow can trap exhaust gases under your vehicle. This can cause deadly CO (carbon monoxide) gas to get inside. CO could overcome you and kill you. You can not see it or smell it, so you might not know it is in your vehicle.
Page 222: If You Are Stuck: In Sand, Mud, Ice Or Snow
Run your engine only as long as you must. This saves fuel. When you run the engine, make it go a little faster than just idle. That is, push the accelerator slightly. This uses less fuel for the heat that you get and it keeps the battery charged.
Page 223: Towing
Notice: Spinning your wheels can destroy parts of your vehicle as well as the tires. If you spin the wheels too fast while shifting your transaxle back and forth, you can destroy your transaxle. See “Rocking Your Vehicle To Get It Out.” For information about using tire chains on your vehicle, see Tire Chains on page 5-72.
Page 224: Recreational Vehicle Towing
Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle — such as behind a motorhome. The two most common types of recreational vehicle towing are known as “dinghy towing” (towing your vehicle with all four wheels on the ground) and “dolly towing”...
Page 225: Dolly Towing
Dolly Towing Your vehicle can be towed using a dolly. To tow your vehicle using a dolly, follow these steps: 1. Put the front wheels on the dolly. 2. Put the vehicle in PARK (P). 3. Set the parking brake and then remove the key. 4.
Page 226 Tire and Loading Information Label Example 1 A. Vehicle Capacity Weight 4-34 Example 2 A. Vehicle Capacity Weight The Tire and Loading Information label shows the seating capacity and the total weight your vehicle can properly carry. This weight is called the vehicle capacity weight.
Page 227 The Tire and Loading Information label also gives you the size and recommended inﬂation pressure for the factory-installed, original equipment tires on your vehicle. For more information on tires and inﬂation see Tires on page 5-58 and Inﬂation - Tire Pressure on page 5-65.
Page 228 Example 1 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 1 = Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight = 4-36 Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs (317 kg) Example 2 Loading Your Vehicle Description...
Page 229 Example 3 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight = Refer to your vehicle’s Tire and Loading Information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight.
Page 230 Certiﬁcation Label The Certiﬁcation label, found on the rear edge of the driver’s door, tells you the gross weight capacity of your vehicle, called the Gross Vehicle Weight Rating (GVWR). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. Never exceed the GVWR for your vehicle, or the Gross Axle Weight Rating (GAWR) for either the front or rear axle.
Page 231: Towing A Trailer
CAUTION: Things you put inside your vehicle can strike and injure people in a sudden stop or turn, or in a crash. • Put things in the trunk of your vehicle. In a trunk, put them as far forward as you can. Try to spread the weight evenly.
Page 232: If You Do Decide To Pull A Trailer
That is the reason for this part. In it are many time-tested, important trailering tips and safety rules. Many of these are important for your safety and that of your passengers. So please read this section carefully before you pull a trailer. Load-pulling components such as the engine, transaxle, wheel assemblies and tires are forced to work harder against the drag of the added weight.
Page 233: Weight Of The Trailer
And, it can also depend on any special equipment that you have on your vehicle. You can ask your dealer for our trailering information or advice, or you can write us at: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, write to:...
Page 234: Total Weight On Your Vehicle's Tires
If you are using a weight-carrying hitch, the trailer tongue (A) should weigh 10 to 15 percent of the total loaded trailer weight (B). After you have loaded your trailer, weigh the trailer and then the tongue, separately, to see if the weights are proper.
Page 235: Trailer Wiring Harness
Safety Chains You should always attach chains between your vehicle and your trailer. Cross the safety chains under the tongue of the trailer so that the tongue will not drop to the road if it becomes separated from the hitch. Instructions about safety chains may be provided by the hitch manufacturer or by the trailer manufacturer.
Page 236: Following Distance
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You will need more passing distance up ahead when you are towing a trailer.
Page 237: Parking On Hills
Your vehicle has bulb warning lights. When you plug a trailer lighting system into your vehicle’s lighting system, its bulb warning lights may not let you know if one of your lamps goes out. So, when you have a trailer lighting system plugged in, be sure to check your vehicle and trailer lamps from time to time to be sure they are all working.
Page 238: Maintenance When Trailer Towing
When You Are Ready to Leave After Parking on a Hill 1. Apply your regular brakes and hold the pedal down while you: • Start your engine. • Shift into a gear. • Release the parking brake. 2. Let up on the brake pedal. 3.
Page 239: Service And Appearance Care
Section 5 Service ...5-3 Doing Your Own Service Work ...5-3 Adding Equipment to the Outside of Your Vehicle ...5-4 Fuel ...5-4 Gasoline Octane ...5-4 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuels in Foreign Countries ...5-6 Filling Your Tank ...5-7 Filling a Portable Fuel Container ...5-9 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 240 Section 5 Wheel Replacement ...5-71 Tire Chains ...5-72 If a Tire Goes Flat ...5-73 Changing a Flat Tire ...5-74 Compact Spare Tire ...5-83 Appearance Care ...5-83 Cleaning the Inside of Your Vehicle ...5-84 Care of Safety Belts ...5-86 Weatherstrips ...5-87 Cleaning the Outside of Your Vehicle ...5-87 Sheet Metal Damage ...5-89 Finish Damage ...5-89...
Page 241: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 242: Adding Equipment To The Outside Of Your Vehicle
CAUTION: (Continued) • Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt. Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it.
Page 243: Gasoline Speciﬁcations
Gasoline Speciﬁcations It is recommended that gasoline meet speciﬁcations which were developed by automobile manufacturers around the world and contained in the World-Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www.autoalliance.org. Gasoline meeting these speciﬁcations could provide improved driveability and emission control system performance compared to other gasoline.
Page 244: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel.
Page 245: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 246 While refueling, hang the tethered fuel cap from the hook on the fuel door. To remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has a spring in it; if you let go of the cap too soon, it will spring back to the right.
Page 247: Filling A Portable Fuel Container
When you put the fuel cap back on, turn it to the right (clockwise) until you hear a clicking sound. Make sure you fully install the cap. The diagnostic system can determine if the fuel cap has been left off or improperly installed.
Page 248: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. 5-10 CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 249: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release handle inside the vehicle. It is located next to the parking brake pedal near the ﬂoor. 2. Then go to the front of the vehicle and pull up on the secondary hood release.
Page 250: Engine Compartment Overview
Engine Compartment Overview When you open the hood on the engine, you’ll see the following: 5-12...
Page 251: Engine Oil
A. Engine Compartment Fuse Block. See “Engine Compartment Fuse Block” under Fuses and Circuit Breakers on page 5-92. B. Windshield Washer Fluid Reservoir. See “Adding Washer Fluid” under Windshield Washer Fluid on page 5-36. C. Remote Positive (+) Terminal. See Jump Starting on page 5-42.
Page 252: When To Add Engine Oil
Pull out the dipstick and clean it with a paper towel or cloth, then push it back in all the way. Remove it again, keeping the tip down, and check the level. When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil.
Page 253 • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle. However, if it is going to be 0°F (–18°C) or above and SAE 5W-30 is not available, you may use SAE 10W-30. These numbers on an oil container show its viscosity, or thickness.
Page 254: Engine Oil Additives
Notice: Use only engine oil identiﬁed as meeting GM Standard GM6094M and showing the American Petroleum Institute Certiﬁed For Gasoline Engines starburst symbol. Failure to use the recommended oil can result in engine damage not covered by your warranty. ® GM Goodwrench oil meets all the requirements for your vehicle.
Page 255: What To Do With Used Oil
When to Change Engine Oil (Vehicles with the GM Oil Life System) If equipped, your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter. This is based on engine revolutions and engine temperature, and not on mileage.
Page 256: Engine Air Cleaner/Filter
Used oil can be a threat to the environment. If you change your own oil, be sure to drain all the oil from the ﬁlter before disposal. Never dispose of oil by putting it in the trash, pouring it on the ground, into sewers, or into streams or bodies of water.
Page 257 2. Remove the air intake hose that is snapped over the throttle body by pulling the hose upward and away from the throttle body which is located near the top of the engine. 3. Disconnect the electrical connector from the air intake hose.
Page 258 5. Inspect or replace the engine air cleaner/ﬁlter. 6. Reinstall the rear section of the engine air cleaner/ﬁlter housing. 7. Reconnect the electrical connector. 8. Reattach the air intake hose by snapping it back onto the throttle body. 9. Refasten the latches to the engine air cleaner/ﬁlter housing cover.
Page 259: Automatic Transaxle Fluid
Automatic Transaxle Fluid When to Check and Change A good time to check your automatic transaxle ﬂuid level is when the engine oil is changed. Change both the ﬂuid and ﬁlter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: •...
Page 260 Checking the Fluid Level Prepare your vehicle as follows: • Park your vehicle on a level place. Keep the engine running. • With the parking brake applied, place the shift lever in PARK (P). • With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
Page 261: Engine Coolant
3. Check both sides of the dipstick, and read the lower level. The ﬂuid level must be in the cross-hatched area. 4. If the ﬂuid level is in the acceptable range, push the dipstick back in all the way. How to Add Fluid Refer to the Maintenance Schedule to determine what kind of transaxle ﬂuid to use.
Page 262: What To Use
A 50/50 mixture of clean, drinkable water and ® DEX-COOL coolant will: • Give freezing protection down to 34°F ( 37°C). • Give boiling protection up to 265°F (129°C). • Protect against rust and corrosion. • Help keep the proper engine temperature. •...
Page 263: Checking Coolant
Checking Coolant The engine coolant recovery tank is located in the engine compartment on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. The vehicle must be on a level surface. When your engine is cold, the coolant level should be at FULL COLD or a little higher.
Page 264 Radiator Pressure Cap If Steam Is Coming From Your Engine Notice: The radiator cap on your vehicle is a pressure-type cap and must be tightly installed to prevent coolant loss and possible engine damage from overheating. Be sure the arrows on the cap line up with the overﬂow tube on the radiator ﬁller neck.
Page 265: If No Steam Is Coming From Your Engine
CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 266: Radiator Pressure Cap
If there’s still no sign of steam, you can idle the engine for three minutes while you’re parked. If you still have the warning, turn off the engine and get everyone out of the vehicle until it cools down. You may decide not to lift the hood but to get service help right away.
Page 267 The coolant level should be at or above the FULL COLD mark when the engine is cold. The coolant level should be at the FULL HOT mark under normal operating conditions. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system.
Page 268 How to Add Coolant to the Coolant Recovery Tank CAUTION: Adding only plain water to your cooling system can be dangerous. Plain water, or some other liquid such as alcohol, can boil before the proper coolant mixture will. Your vehicle’s coolant warning system is set for the proper coolant mixture.
Page 269: How To Add Coolant To The Radiator
CAUTION: Steam and scalding liquids from a hot cooling system can blow out and burn you badly. They are under pressure, and if you turn the radiator pressure cap — even a little — they can come out at high speed. Never turn the cap when the cooling system, including the radiator pressure cap, is hot.
Page 270 2. Then keep turning the pressure cap, but now push down as you turn it. Remove the pressure cap. 3. Remove the 3800 Series II V6 engine cover shield to access the bleed valve. 5-32 3.1. Clean the area around the engine oil ﬁll tube and cap before removing.
Page 271 4. After the engine cools, 5. Fill the radiator with the proper DEX-COOL open the coolant air bleed valve. There is one bleed valve. It is located on the thermostat housing. 6. Rinse or wipe any spilled coolant from the engine 7.
Page 272 8. Then ﬁll the coolant recovery tank to the FULL COLD mark. 9. Put the cap back on the coolant recovery tank, but leave the radiator pressure cap off. 5-34 10. Start the engine and let it run until you can feel the upper radiator hose getting hot.
Page 273: Power Steering Fluid
11. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁller neck until the level reaches the base of the ﬁller neck. 12.
Page 274: When To Check Power Steering Fluid
When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired.
Page 275: Brakes
Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. • Don’t mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system. Also, water doesn’t clean as well as washer ﬂuid.
Page 276 The other reason is that ﬂuid is leaking out of the brake system. If it is, you should have your brake system ﬁxed, since a leak means that sooner or later your brakes will not work well, or will not work at all. So, it is not a good idea to “top off”...
Page 277: Brake Wear
• If you spill brake ﬂuid on your vehicle’s painted surfaces, the paint ﬁnish can be damaged. Be careful not to spill brake ﬂuid on your vehicle. If you do, wash it off immediately. See Appearance Care on page 5-83. Brake Wear Your vehicle has four-wheel disc brakes.
Page 278: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 279: Vehicle Storage
To be sure the vent hose (A) is properly attached, the vent hose connectors (B) must be securely reattached to the vent outlets (C) on each side of the battery, and the vent assembly grommet (D) must be secured to the ﬂoor pan (E).
Page 280: Jump Starting
Jump Starting If your vehicle’s battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to use the steps below to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 281 Notice: If you leave your radio or other accessories on during the jump starting procedure, they could be damaged. The repairs would not be covered by your warranty. Always turn off your radio and other accessories when jump starting your vehicle. 3.
Page 282 CAUTION: Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a ﬂashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the ACDelco installed in your new vehicle.
Page 283 6. Connect the red positive (+) cable to the positive (+) terminal of the dead battery. Use a remote positive (+) terminal if the vehicle has one. 7. Don’t let the other end touch metal. Connect it to the positive (+) terminal of the good battery.
Page 284 9. Connect the other end of the negative ( ) cable at least 18 inches (45 cm) away from the dead battery, but not near engine parts that move. The electrical connection is just as good there, and the chance of sparks getting back to the battery is much less.
Page 285: Headlamp Aiming
To disconnect the jumper cables from both vehicles, do the following: 1. Disconnect the black negative ( ) cable from the vehicle that had the dead battery. 2. Disconnect the black negative ( ) cable from the vehicle with the good battery. 3.
Page 286 If your vehicle is damaged in an accident, the headlamp aim may be affected. Aim adjustment to the low beam may be necessary if it is difficult to see lane markers (for horizontal aim), or if oncoming drivers ﬂash their high beams at you (for vertical aim).
Page 287: Headlamp Horizontal Aiming
The headlamp aiming devices are under the hood near the headlamps. If you believe your headlamps need horizontal (left/right) adjustment, follow the horizontal aiming procedure. If you believe your headlamps need only vertical (up/down) adjustment, follow only the vertical aiming procedure.
Page 288: Headlamp Vertical Aiming
Headlamp Vertical Aiming Notice: Horizontal aiming must be performed before making any adjustments to the vertical aim. Adjusting the vertical aim ﬁrst will result in an incorrect headlamp aim. 1. Find the aim dot on the lens of the low beam lamps.
Page 289 Notice: Do not cover a headlamp to improve beam cut-off when aiming. Covering a headlamp may cause excessive heat build-up which may cause damage to the headlamp. 5. Turn the vertical aiming screw (C) until the headlamp beam is aimed to the horizontal tape line.
Page 290: Bulb Replacement
Bulb Replacement For the type of bulb to use, see Replacement Bulbs on page 5-56. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 291: Front Turn Signal Lamps
4. Turn the bulb retainer counterclockwise to remove it from the bulb assembly. 5. Pull the old bulb straight out from the retainer. Push the new bulb straight into the retainer. 6. Reverse Steps 1 through 4 to reinstall the headlamp assembly.
Page 292: Taillamps, Turn Signal, And Stoplamps
Taillamps, Turn Signal, and Stoplamps 1. Open the trunk. Turn the screws located just inside of the trunk counterclockwise and remove them. 2. Remove the plastic trim piece from the trunk. 3. Pull the carpet away from the rear area to access the turn signal bulb assembly.
Page 293: Taillamps And Back-Up Lamps
Taillamps and Back-Up Lamps 2. Pull out the assembly. 1. Open the trunk. Loosen and remove the seven fasteners that hold the taillamp assembly in place. The assembly for both sides is one piece. The entire piece must be removed to replace any bulbs.
Page 294: Replacement Bulbs
3. Push in the tab and turn the bulb socket counterclockwise to remove it. 4. Remove the bulb by pulling it straight out. 5. Replace the bulb and reverse the steps to install the assembly. 5-56 Replacement Bulbs Exterior Lamp Front Low Beam Headlamps High Beam Headlamps...
Page 295: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Wiper Blade Check” under Part B: Owner Checks and Services on page 6-17 for more information. Replacement blades come in different types and are removed in different ways.
Page 296: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 297 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 298 (E) Tire Ply Material: The type of cord and number of plies in the sidewall and under the tread. (F) Uniform Tire Quality Grading (UTQG): Tire manufacturers are required to grade tires based on three performance factors: treadwear, traction and temperature resistance.
Page 299 (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 300: Tire Size
Tire Size The following illustration shows an example of a typical passenger car tire size. (A) P-Metric Tire: The United States version of a metric tire sizing system. The letter “P” as the ﬁrst character in the tire size means a passenger vehicle tire engineered to standards set by the U.
Page 301 Belt: A rubber coated layer of cords that is located between the plies and the tread. Cords may be made from steel or other reinforcing materials. Bead: The tire bead contains steel wires wrapped by steel cords that hold the tire onto the rim. Bias Ply Tire: A pneumatic tire in which the plies are laid at alternate angles substantially less than 90 degrees to the centerline of the tread.
Page 302 Occupant Distribution: Designated seating positions. Outward Facing Sidewall: The side of a asymmetrical tire that has a particular side that faces outward when mounted on a vehicle. The side of the tire that contains a whitewall, bears white lettering or bears manufacturer, brand and or model name molding that is higher or deeper than the same moldings on the other sidewall of the tire.
Page 303: Inﬂation - Tire Pressure
Inﬂation - Tire Pressure The tire and loading information label, shows the correct inﬂation pressures for your tires when they’re cold. “Cold” means your vehicle has been sitting for at least three hours or driven no more than 1 mile (1.6 km). See Loading Your Vehicle on page 4-33, for the location of your vehicle’s tire and loading information label.
Page 304: Check Tire Pressure System
Check Tire Pressure System If your vehicle has the check tire pressure system, it can alert you to a large change in the pressure of one tire. The system will not alert you before you drive that a tire is low or ﬂat. You must begin driving before the system will work properly.
Page 305: Tire Inspection And Rotation
To reset (calibrate) the system: 1. Turn the ignition switch to RUN. 2. Press the GAGE INFO button on the DIC until TIRE PRESSURE appears on the display. 3. Press and hold the DIC RESET button for about ﬁve seconds. After ﬁve seconds, the display will show TIRE PRESSURE RESET.
Page 306: When It Is Time For New Tires
Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Tire and Loading Information label. Reset the check tire pressure system, if equipped. See Check Tire Pressure System on page 5-66.
Page 307: Buying New Tires
Buying New Tires To ﬁnd out what kind and size of tires you need, look at the tire and loading information label. For an example of this label and its location, see Loading Your Vehicle on page 4-33. The tires installed on your vehicle when it was new had a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall.
Page 308: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 309: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 310: Used Replacement Wheels
If you need to replace any of your wheels, wheel bolts or wheel nuts, replace them only with new GM original equipment parts. This way, you will be sure to have the right wheel, wheel bolts and wheel nuts for your vehicle. CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be...
Page 311: If A Tire Goes Flat
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side.
Page 312: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 313: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the trunk. 1. Pull the carpeting from the ﬂoor of the trunk. 2. Lift and remove the cover. 3. Remove the compact spare tire. See Compact Spare Tire on page 5-83 for more information about the compact spare.
Page 314 Removing the Wheel Covers and Wheel Nut Caps 5-76 If your vehicle has an aluminum wheel with a center hub cap that hides the wheel nuts, remove the hub cap by using the ﬂat end of the wheel wrench to pry it off.
Page 315 Removing the Flat Tire and Installing the Spare Tire 1. Then use the wheel wrench to loosen the wheel nuts, but do not remove them yet. 2. The jack has a bolt at the end. Attach the wheel wrench to the bolt to create a jack handle. 3.
Page 316 4. Put the jack into a notch in the frame which is located near each wheel well. The front notch is eight inches (20 cm) back from the front wheel well. The rear notch is three inches (8 cm) forward from the rear wheel well.
Page 317 5. Raise the vehicle by turning the wheel wrench clockwise in the jack. Raise the vehicle far enough so there is enough room for the spare tire to ﬁt under the wheel well. 6. Remove all the wheel nuts and take off the ﬂat tire. 7.
Page 318 CAUTION: Never use oil or grease on studs or nuts. If you do, the nuts might come loose. Your wheel could fall off, causing a serious accident. 8. Place the compact spare tire on the wheel-mounting surface. 9. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel.
Page 319: Storing The Flat Tire And Tools
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. See “Capacities and Speciﬁcations” in the index for the wheel nut torque speciﬁcation.
Page 320: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools CAUTION: Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place. Store the compact spare tire and tools as shown in the diagram.
Page 321: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when your vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inﬂated.
Page 322: Cleaning The Inside Of Your Vehicle
Never use these to clean your vehicle: • Gasoline • Benzene • Naphtha • Carbon Tetrachloride • Acetone • Paint Thinner • Turpentine • Lacquer Thinner • Nail Polish Remover They can all be hazardous — some more than others — and they can all damage your vehicle, too. Do not use any of these unless this manual says you can.
Page 323: Using Cleaner On Fabric
Using Cleaner on Fabric 1. Vacuum and brush the area to remove any loose dirt. 2. Always clean a whole trim panel or section. Mask surrounding trim along stitch or welt lines. 3. Follow the directions on the container label. 4.
Page 324: Cleaning Leather
Cleaning Leather Use a soft cloth with lukewarm water and a mild soap or saddle soap and wipe dry with a soft cloth. Then, let the leather dry naturally. Do not use heat to dry. • For stubborn stains, use a leather cleaner. •...
Page 325: Weatherstrips
Weatherstrips Silicone grease on weatherstrips will make them last longer, seal better, and not stick or squeak. Apply silicone grease with a clean cloth at least every six months. During very cold, damp weather more frequent application may be required. See Part D: Recommended Fluids and Lubricants on page 6-23.
Page 326: Cleaning Aluminum Or Chrome-Plated Wheels
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s ﬁnish if they remain on painted surfaces. Wash the vehicle as soon as possible. If necessary, use non-abrasive cleaners that are marked safe for painted surfaces to remove foreign matter.
Page 327: Cleaning Tires
Cleaning Tires To clean your tires, use a stiff brush with tire cleaner. Notice: Using petroleum-based tire dressing products on your vehicle may damage the paint ﬁnish and/or tires. When applying a tire dressing, always wipe off any overspray from all painted surfaces on your vehicle.
Page 328: Vehicle Care/Appearance Materials
Vehicle Care/Appearance Materials See your GM dealer for more information on purchasing the following products. Vehicle Care/Appearance Materials Description Polishing Cloth Interior and exterior Wax-Treated polishing cloth. Tar and Road Oil Removes tar, road oil and Remover asphalt. Chrome Cleaner and Use on chrome or stainless Polish steel.
Page 329: Vehicle Identiﬁcation
Vehicle Identiﬁcation Vehicle Identiﬁcation Number (VIN) This is the legal identiﬁer for your vehicle. It appears on a plate in the front corner of the instrument panel, on the driver’s side. You can see it if you look through the windshield from outside your vehicle.
Page 330: Power Windows And Other Power Options
Power Windows and Other Power Options Circuit breakers in the rear fuse block protect the power windows and other power accessories. When the current load is too heavy, the circuit breaker opens and closes, protecting the circuit until the problem is ﬁxed or goes away.
Page 331 Fuses Usage Not Used Accessory Windshield Wipers Not Used Left Low-Beam Headlamp Right Low-Beam Headlamp Instrument Panel Fuses Usage Powertrain Control Module Battery Right High-Beam Headlamp Left High-Beam Headlamp Ignition 1 Not Used Transaxle Cruise Control Direct Ignition System Injector Bank #2 Not Used Not Used Powertrain Control Module Ignition...
Page 332 Relays Usage High-Beam Headlamp Low-Beam Headlamp Fog Lamps Daytime Running Lamps Horn Air Conditioner Clutch HVAC Solenoid Accessory Not Used Starter 1 Cooling Fan 1 Ignition 1 Cooling Fan Series/Parallel Cooling Fan 2 Circuit Breakers Usage Starter 5-94 Fuses Usage Not Used Empty Not Used...
Page 333: Removing The Rear Seat Cushion
Removing the Rear Seat Cushion Notice: If you touch the exposed wires with the metal on the seat cushion, you could cause a short that could damage the battery and or wires. Avoid contact between the rear seat and the fuse center whenever you remove or reinstall the rear seat.
Page 334: Rear Underseat Fuse Block
1. Buckle the center passenger position safety belt, then route the safety belts through the proper slots in the seat cushion. Don’t let the safety belts get twisted. 2. Slide the rear of the cushion up and under the seatback so the rear-locating guides hook into the wire loops on the back frame.
Page 335 Fuses Usage Fuel Pump HVAC Blower Memory Assembly Line Diagnostic Link Not Used Compact Disc (CD) Driver’s Door Module Air Bag System (SIR) Not Used Right Parking Lamp Vent Solenoid Ignition 1 Fuses Usage Left Parking Lamp Dimmer Satellite Digital Radio Left Front Heated Seat Not Used Rear Door Module...
Page 336 Relays Usage Fuel Pump Parking Lamp Ignition 1 Rear Fog Lamp Not Used Park Reverse Retained Accessory Power (RAP) Fuel Tank Door Lock Not Used Ignition 3 Fuel Tank Door Release Interior Lamps Trunk Release Front Courtesy Lamps Not Used Electronic Level Control (ELC) Circuit Usage...
Page 337: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Please refer to Part D: Recommended Fluids and Lubricants on page 6-23 for more information. Application Air Conditioning Refrigerant R134a Automatic Transaxle Engine Cooling System Engine Oil with Filter Fuel Tank Wheel Nut Torque All capacities are approximate.
Page 338: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Replacement parts identiﬁed below by name, part number, or speciﬁcation can be obtained from your dealer. Part Engine Air Cleaner/Filter Engine Oil Filter Fuel Filter Passenger Compartment Air Filter Spark Plugs Transaxle Filter Windshield Wiper Blades Type Length 5-100...
Page 339 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 How This Section is Organized ...6-3 Part A: Scheduled Maintenance Services ...6-4 Using Your Maintenance Schedule ...6-4 Selecting the Right Schedule ...6-5 Short Trip/City Scheduled Maintenance ...6-6 Long Trip/Highway Scheduled Maintenance ...6-13 Part B: Owner Checks and Services ...6-17 At Each Fuel Fill ...6-17...
Page 340: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Maintenance intervals, checks, inspections and recommended ﬂuids and lubricants as prescribed in this...
Page 341: How This Section Is Organized
How This Section is Organized This maintenance schedule is divided into ﬁve parts: “Part A: Scheduled Maintenance Services” explains what to have done and how often. Some of these services can be complex, so unless you are technically qualiﬁed and have the necessary equipment, you should let your GM dealer’s service department do these jobs.
Page 342: Part A: Scheduled Maintenance Services
Part A: Scheduled Maintenance Services In this part are scheduled maintenance services which are to be performed at the mileage intervals speciﬁed. Using Your Maintenance Schedule We at General Motors want to keep your vehicle in good working condition. But we do not know exactly how you will drive it.
Page 343: Selecting The Right Schedule
Selecting the Right Schedule First you’ll need to decide which of the two schedules is right for your vehicle. Here’s how to decide which schedule to follow: Short Trip/City Deﬁnition Follow the Short Trip/City Scheduled Maintenance if any one of these conditions is true for your vehicle: •...
Page 344: Long Trip/Highway Deﬁnition
Long Trip/Highway Deﬁnition Follow this scheduled maintenance only if none of the conditions from the Short Trip/City Scheduled Maintenance are true. Do not use this schedule if the vehicle is used for trailer towing, driven in a dusty area or used off paved roads. Use the Short Trip/City schedule for these conditions Driving a vehicle with a fully warmed engine under highway conditions will cause engine oil to break down...
Page 345 Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 346 12,000 Miles (20 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Rotate tires. See Tire Inspection and Rotation on page 5-67 for proper rotation pattern and additional information.
Page 347 33,000 Miles (55 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) 36,000 Miles (60 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Rotate tires.
Page 348 50,000 Miles (83 000 km) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 349 69,000 Miles (115 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) 72,000 Miles (120 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Rotate tires.
Page 350 90,000 Miles (150 000 km) Change engine oil and ﬁlter (or every 3 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Replace engine air cleaner ﬁlter. See Engine Air Cleaner/Filter on page 5-18 for more information. An Emission Control Service. Rotate tires.
Page 351: Long Trip/Highway Scheduled Maintenance
Long Trip/Highway Scheduled Maintenance The services shown in this schedule up to 100,000 miles (166 000 km) should be repeated after 100,000 miles (166 000 km) at the same intervals for the life of this vehicle. The services shown at 150,000 miles (240 000 km) should be repeated at the same interval after 150,000 miles (240 000 km) for the life of this vehicle.
Page 352 7,500 Miles (12 500 km) Change engine oil and ﬁlter (or every 12 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Rotate tires. See Tire Inspection and Rotation on page 5-67 for proper rotation pattern and additional information.
Page 353 50,000 Miles (83 000 km) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 354 82,500 Miles (137 500 km) Change engine oil and ﬁlter (or every 12 months, whichever occurs ﬁrst). An Emission Control Service. (See footnote *.) Rotate tires. See Tire Inspection and Rotation on page 5-67 for proper rotation pattern and additional information.
Page 355: Part B: Owner Checks And Services
Part B: Owner Checks and Services Listed in this part are owner checks and services which should be performed at the intervals speciﬁed to help ensure the safety, dependability and emission control performance of your vehicle. Be sure any necessary repairs are completed at once. Whenever any ﬂuids or lubricants are added to your vehicle, make sure they are the proper ones, as shown in Part D.
Page 356: At Least Twice A Year
At Least Twice a Year Restraint System Check Make sure the safety belt reminder light and all your belts, buckles, latch plates, retractors and anchorages are working properly. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired.
Page 357: Starter Switch Check
Starter Switch Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. 2. Firmly apply both the parking brake and the regular brake.
Page 358: Ignition Transaxle Lock Check
Ignition Transaxle Lock Check While parked, and with the parking brake set, try to turn the ignition key to LOCK in each shift lever position. • The key should turn to LOCK only when the shift lever is in PARK (P). •...
Page 359: Part C: Periodic Maintenance Inspections
Part C: Periodic Maintenance Inspections Listed in this part are inspections and services which should be performed at least twice a year (for instance, each spring and fall). You should let your dealer’s service department do these jobs. Make sure any necessary repairs are completed at once.
Page 360: Fuel System Inspection
Fuel System Inspection Inspect the complete fuel system for damage or leaks. Engine Cooling System Inspection Inspect the hoses and have them replaced if they are cracked, swollen or deteriorated. Inspect all pipes, ﬁttings and clamps; replace as needed. Clean the outside of the radiator and air conditioning condenser.
Page 361: Part D: Recommended Fluids And Lubricants
Part D: Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 362: Part E: Maintenance Record
Part E: Maintenance Record After the scheduled services are performed, record the date, odometer reading and who performed the service and any additional information from “Owner Checks and Services” or “Periodic Maintenance” on the following record pages. Also, you should retain all maintenance receipts. Maintenance Record Odometer Date...
Page 363 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-25...
Page 364 Maintenance Record (cont’d) Odometer Date Serviced By Maintenance Record Reading 6-26...
Page 365: Customer Assistance Information
Section 7 Customer Assistance Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-3 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-4 GM Mobility Program for Persons with Disabilities ...7-5 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-7 Vehicle Data Collection and Event Data Records ...7-9 Customer Assistance Information...
Page 366: Customer Assistance Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 367: Online Owner Center
The BBB Auto Line Program is an out of court program administered by the Council of Better Business Bureaus to settle automotive disputes regarding vehicle repairs or the interpretation of the New Vehicle Limited Warranty. Although you may be required to resort to this informal dispute resolution program prior to ﬁling a court action, use of the program is free of charge and your case will generally be heard within...
Page 368: Customer Assistance For Text Telephone (Tty) Users
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Buick has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Buick by dialing: 1-800-83-BUICK. (TTY users in Canada can dial 1-800-263-3830.)
Page 369: Gm Mobility Program For Persons With Disabilities
Overseas – Customer Assistance Please contact the local General Motors Business Unit. Mexico, Central America and Caribbean Islands/Countries (Except Puerto Rico and U.S. Virgin Islands) – Customer Assistance General Motors de Mexico, S. de R.L. de C.V. Customer Assistance Center Paseo de la Reforma # 2740 Col.
Page 370: Roadside Assistance Program
Roadside Assistance Program Buick Motor Division is proud to offer Buick Premium Roadside Assistance to customers for vehicles covered under the 3 year/36,000 mile (60 000 km) new car warranty (whichever occurs ﬁrst). Our commitment to Buick owners has always included superior service through our network of Buick dealers.
Page 371: Courtesy Transportation
Canada or the United States. Please refer to the Warranty and Owner Assistance Information book. Courtesy Transportation Buick has always exempliﬁed quality and value in its offering of motor vehicles. To enhance your ownership experience, we and our participating dealers are proud to offer Courtesy Transportation, a customer support program for new vehicles.
Page 372: Transportation Options
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Buick helps minimize your inconvenience by providing several transportation options. Depending on the circumstances, your dealer can offer you one of the following:...
Page 373: Vehicle Data Collection And Event Data Records
Additional Program Information Courtesy Transportation is available during the Bumper-to-Bumper warranty coverage period, but it is not part of the New Vehicle Limited Warranty. A separate booklet entitled Warranty and Owner Assistance Information furnished with each new vehicle provides detailed warranty coverage information. Courtesy Transportation is available only at participating dealers and all program options, such as shuttle service, may not be available at every dealer.
Page 374: Reporting Safety Defects
To read this information, special equipment is needed and access to the vehicle or the SDM is required. GM will not access information about a crash event or share it with others other than • with the consent of the vehicle owner or, if the vehicle is leased, with the consent of the lessee, •...
Page 375: Reporting Safety Defects To The Canadian Government
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-521-7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 376: Service Bulletins
Service Bulletins Service Bulletins give technical service information needed to knowledgeably service General Motors cars and trucks. Each bulletin contains instructions to assist in the diagnosis and service of your vehicle. In Canada, information pertaining to Product Service Bulletins can be obtained by contacting your General Motors dealer or by calling 1-800-GM-DRIVE (1-800-463-7483).
Page 377 Accessory Power Outlets ... 3-22 Adding Washer Fluid ... 5-36 Additional Program Information ... 7-9 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-91 Adjusting the Speakers (Balance/Fade) ... 3-57, 3-65 Air Bag Readiness Light ... 3-36 Air Bag Systems ... 1-47 How Does an Air Bag Restrain? ...
Page 378 Automatic Transaxle Fluid ... 5-21 Operation ... 2-25 Automatic Transaxle Check ... 6-18 Automatic Transaxle Shift Lock Control System Check ... 6-19 Backing Up ... 4-44 Battery ... 5-40 Battery Load Management ... 3-20 Battery Replacement ... 2-8 Battery Warning Light ... 3-37 Before Leaving on a Long Trip ...
Page 379 Check Engine Light ... 3-40 Tire Pressure System ... 5-66 Checking Coolant ... 5-25 Checking Engine Oil ... 5-13 Checking Things Under the Hood ... 5-10 Checking Your Restraint Systems ... 1-56 Chemical Paint Spotting ... 5-89 Child Restraints Child Restraint Systems ... 1-33 Infants and Young Children ...
Page 380 Coolant Engine Temperature Gage ... 3-40 Heater, Engine ... 2-24 Cooling System ... 5-28 Cornering Lamps ... 3-15 Courtesy Lamps ... 3-18 Cruise Control ... 3-11 Cruise Control Light ... 3-44 Current and Past Model Order Forms ... 7-12 Customer Assistance Information Courtesy Transportation ...
Page 381 Driving (cont.) In Rain and on Wet Roads ... 4-17 Winter ... 4-25 Driving On Grades ... 4-45 Driving on Snow or Ice ... 4-26 Driving Through Deep Standing Water ... 4-19 Driving Through Flowing Water ... 4-20 Driving with a Trailer ... 4-43 Dual Automatic Climate Control System ...
Page 382 Flat Tire ... 5-73 Flat Tire, Changing ... 5-74 Fluid Automatic Transaxle ... 5-21 Power Steering ... 5-35 Windshield Washer ... 5-36 FM Stereo ... 3-79 Following Distance ... 4-44 Footnotes ... 6-7, 6-13 Front Reading Lamps ... 3-19 Fuel ... 5-4 Additives ...
Page 383 Hitches ... 4-42 ® HomeLink Transmitter ... 2-38 ® HomeLink Transmitter, Programming ... 2-39 Hood Checking Things Under ... 5-10 Release ... 5-11 Horn ... 3-7 How to Add Coolant to the Coolant Recovery Tank ... 5-30 How to Add Coolant to the Radiator ... 5-31 How to Add Fluid ...
Page 384 Lamps Exterior ... 3-14 Interior ... 3-17 Language Selection ... 3-54 Lap Belt ... 1-19 Lap-Shoulder Belt ... 1-12, 1-21 LATCH System Child Restraints ... 1-39 Securing a Child Restraint Designed for the LATCH System ... 1-41 Leaving Your Vehicle ... 2-13 Leaving Your Vehicle With the Engine Running ...
Page 385 Maintenance Schedule (cont.) How This Section is Organized ... 6-3 Introduction ... 6-2 Long Trip/Highway Scheduled Maintenance ... 6-13 Maintenance Requirements ... 6-2 Part A - Scheduled Maintenance Services ... 6-4 Part B - Owner Checks and Services ... 6-17 Part C - Periodic Maintenance Inspections ...
Page 386 Engine ... 5-13 Pressure Light ... 3-43 Older Children, Restraints ... 1-27 Online Owner Center ... 7-3 ® OnStar Personal Calling ... 2-38 ® OnStar Services ... 2-37 ® OnStar System ... 2-37 ® OnStar Virtual Advisor ... 2-38 Other Warning Devices ... 3-6 Outlet Adjustment ...
Page 387 Power Accessory Outlets ... 3-22 Door Locks ... 2-10 Electrical System ... 5-92 Lumbar Controls ... 1-3 Seat ... 1-2 Steering Fluid ... 5-35 Windows ... 2-17 Power Steering ... 4-10 Programmable Automatic Door Locks ... 2-12 ® Programming the HomeLink Transmitter ...
Page 388 Reporting Safety Defects Canadian Government ... 7-11 General Motors ... 7-11 United States Government ... 7-10 Reprogramming a Single HomeLink Resetting Defaults ... 2-42 Restraint System Check ... 6-18 Checking Your Restraint Systems ... 1-56 Replacing Restraint System Parts After a Crash ...
Page 389 Service ... 5-3 Adding Equipment to the Outside of Your Vehicle ... 5-4 Doing Your Own Work ... 5-3 Engine Soon Light ... 3-40 Publications Ordering Information ... 7-11 Vehicle Soon Light ... 3-44 Service Bulletins ... 7-12 Service Engine Soon Light ... 3-40 Service Manuals ...
Page 390 Tire Inﬂation Check ... 6-17 Tire Sidewall Labeling ... 5-58 Tire Size ... 5-62 Tire Terminology and Deﬁnitions ... 5-62 Tires ... 5-58 Buying New Tires ... 5-69 Chains ... 5-72 Changing a Flat Tire ... 5-74 Check Tire Pressure System ... 5-66 Compact Spare Tire ...
Page 391 Vehicle Control ... 4-5 Damage Warnings ... iv Loading ... 4-33 Service Soon Light ... 3-44 Symbols ... iv Vehicle Data Collection and Event Data Records .. 7-9 Vehicle Identiﬁcation Number (VIN) ... 5-91 Service Parts Identiﬁcation Label ... 5-91 Vehicle Personalization DIC ...
Page 392 Windshield Washer Fluid Level Check ... 6-17 Windshield Wiper Blade Replacement ... 5-57 Windshield Wipers ... 3-9 Winter Driving ... 4-25 Wiper Activated Headlamps ... 3-14 Wiper Blade Check ... 6-18 XM™ Satellite Radio Antenna System ... 3-82 XM™ Satellite Radio Service (48 Contiguous US States) ...

Buick 2004 LeSabre Owner's Manual

Table of Contents

Seats and Restraint Systems

Features and Controls

Instrument Panel

Section 3 Instrument Panel

Maintenance Schedule

Service and Appearance Care

Audio System(S)

Section 4 Driving Your Vehicle

Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Section 5 Service and Appearance Care

Service and Appearance Care

Service

Fuel

Checking Things under the Hood

Headlamp Aiming

Bulb Replacement

Windshield Wiper Blade Replacement

Tires

Appearance Care

Vehicle Identiﬁcation

Electrical System

Capacities and Speciﬁcations

Normal Maintenance Replacement Parts

Quick Links

Chapters

Related Manuals for Buick 2004 LeSabre

Summary of Contents for Buick 2004 LeSabre