Page 1: Table Of Contents
2004 Buick Rendezvous Owner Manual Seats and Restraint Systems ... 1-1 Front Seats ... 1-3 Rear Seats ... 1-9 Safety Belts ... 1-22 Child Restraints ... 1-47 Air Bag Systems ... 1-72 Restraint System Check ... 1-82 Features and Controls ... 2-1 Keys ...
Page 2: How To Use This Manual
GENERAL MOTORS, GM, the GM Emblem, BUICK, the BUICK Emblem and the name RENDEZVOUS are registered trademarks of General Motors Corporation. This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice.
Page 3 Index A good place to look for what you need is the Index in back of the manual. It is an alphabetical list of what is in the manual, and the page number where you will ﬁnd it. Safety Warnings and Symbols You will ﬁnd a number of safety cautions in this book.
Page 4 Vehicle Damage Warnings Also, in this book you will ﬁnd these notices: Notice: These mean there is something that could damage your vehicle. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly.
Page 5 These are some examples of vehicle symbols you may ﬁnd on your vehicle:...
Page 6 NOTES...
Page 7: Seats And Restraint Systems
Section 1 Front Seats ...1-3 Manual Passenger Seat ...1-3 Four-Way Manual Driver Seat ...1-3 Six-Way Power Seats ...1-5 Manual Lumbar ...1-5 Heated Seats ...1-6 Reclining Seatbacks ...1-6 Head Restraints ...1-8 Rear Seats ...1-9 Rear Seat Operation ...1-9 Split Bench Seats ...1-9 Captain Chairs ...1-14 Stowable Seat ...1-18 Safety Belts ...1-22...
Page 8 Section 1 Air Bag Systems ...1-72 Where Are the Air Bags? ...1-75 When Should an Air Bag Inﬂate? ...1-77 What Makes an Air Bag Inﬂate? ...1-78 How Does an Air Bag Restrain? ...1-79 What Will You See After an Air Bag Inﬂates? ...1-80 Servicing Your Air Bag-Equipped Vehicle ...1-82 Seats and Restraint Systems Restraint System Check ...1-82...
Page 9: Front Seats
Front Seats Manual Passenger Seat Pull up on the lever, located on the front of the seat, to unlock and move the seat. Slide the seat to where you want it and release the lever. To make sure the seat is locked into place, try to move the seat back and forth with your body.
Page 10 To raise the seat, pull up on the lever located on the front right side of the seat. To lower the seat, push the lever down. Adjust the seat and release the lever. CAUTION: You can lose control of the vehicle if you try to adjust a manual driver’s seat while the vehicle is moving.
Page 11: Six-Way Power Seats
Six-Way Power Seats Your vehicle may have this feature. If it does, the six-way power seat control is located on the outboard sides of the driver’s and front passenger’s seats. • Move the front of the control up or down to adjust the front portion of the cushion up or down.
Page 12 Heated Seats Your vehicle may have heated seats. If it does, the heated seat switches are located in the instrument panel switchbank. This feature will quickly heat the seat cushions and lower back of the driver’s and front passenger’s seat. The left switch is for the driver’s seat and the right switch is for the front passenger’s seat.
Page 13 But don’t have a seatback reclined if your vehicle is moving. CAUTION: Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job because it won’t be against your body.
Page 14: Head Restraints
Head Restraints Adjust your head restraint so that the top of the restraint is closest to the top of your head. This position reduces the chance of a neck injury in a crash. The front seat head restraints are adjustable. Slide the head restraint up or down to adjust it.
Page 15: Rear Seats
Rear Seats Rear Seat Operation The rear seats in your vehicle have seat operating features to adjust, fold, remove and reinstall the seats. By using the seat operating procedures, in the correct order, you can easily remove the seats from your vehicle.
Page 16: Removing The Split Bench Seat
To recline the seatback on up-level split bench seats, push forward on the recliner lever located on the outboard side of the seatback. Up-Level Move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback.
Page 17 Base-Level 4. For base-level split bench seats, pull the lever at the base of the seat on the outboard side to release the rear latches from the ﬂoor pins and ﬂip the seat forward. For up-level split bench seats, continue pushing forward on the recliner lever to release the rear latches from the ﬂoor pins and ﬂip the seat forward.
Page 18: Replacing The Split Bench Seat
Replacing the Split Bench Seat CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 19 1. Squeeze the angled latch release bar toward the straight crossbar while placing the front hooks of the bench seat onto the front two ﬂoor pins. 2. Make sure that the bench seat is angled so that the front hooks clear the ﬂoor pins.
Page 20: Captain Chairs
3. Firmly push the rear hooks onto the rear ﬂoor pins by pushing down on the rear of the seat. 4. Try to raise the seat to check that it is locked down. 5. Lift the seatback recliner lever and raise the seatback until it locks upright.
Page 21: Removing The Captain's Chairs
To recline the seatback, lift up on the recliner lever located on the outboard side of the seatback. Use the recliner lever to move the seatback to the desired position. It is easier to raise or lower the seatback if you lean forward and take the weight off the seatback.
Page 22: Replacing The Captain's Chairs
4. The seat can then be lifted off the front ﬂoor pins. 5. Remove the seat by rocking it slightly toward the rear of the vehicle and then pulling it out. Repeat these steps for the other captain’s chair. 1-16 Replacing the Captain’s Chairs CAUTION: If the seatback isn’t locked, it could move...
Page 23 CAUTION: A safety belt that is improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash. The person wearing the belt could be seriously injured. After installing the seat, always check to be sure that the safety belts are properly routed and attached, and are not twisted.
Page 24: Stowable Seat
2. Push the rear of the seat down to lock the rear latches onto the rear set of ﬂoor pins. 3. Push and pull on the seat to check that it is properly attached. 1-18 Stowable Seat The stowable seat is a two passenger bench seat and comes with the rear convenience center.
Page 25: Removing The Stowable Seat
To fold the seatback down, pull up on the lever located on the back of the seat. Push down on the seatback until it is locked into place. Push and pull on the seatback to make sure that it is locked into place.
Page 26: Replacing The Stowable Seat
Replacing the Stowable Seat CAUTION: If the seatback isn’t locked, it could move forward in a sudden stop or crash. That could cause injury to the person sitting there. Always press rearward on the seatback to be sure it is locked.
Page 27 The stowable seat has seat position labels, located on the back of the seat, showing where the seat must go. The seat must be placed in the proper location for the legs to attach correctly. Make sure that the seatback is folded forward before beginning this procedure.
Page 28: Safety Belts
Safety Belts Safety Belts: They Are for Everyone This part of the manual tells you how to use safety belts properly. It also tells you some things you should not do with safety belts. CAUTION: Don’t let anyone ride where he or she can’t wear a safety belt properly.
Page 29: Why Safety Belts Work
Your vehicle has a light that comes on as a reminder to buckle up. See Safety Belt Reminder Light on page 3-43. In most states and in all Canadian provinces, the law says to wear safety belts. Here’s why: They work. You never know if you’ll be in a crash.
Page 30 Put someone on it. 1-24 Get it up to speed. Then stop the vehicle. The rider doesn’t stop.
Page 31 The person keeps going until stopped by something. In or the instrument panel... a real vehicle, it could be the windshield... 1-25...
Page 32: Questions And Answers About Safety Belts
or the safety belts! With safety belts, you slow down as the vehicle does. You get more time to stop. You stop over more distance, and your strongest bones take the forces. That’s why safety belts make such good sense. 1-26 Questions and Answers About Safety Belts...
Page 33: How To Wear Safety Belts Properly
If I’m a good driver, and I never drive far from home, why should I wear safety belts? You may be an excellent driver, but if you’re in an accident – even one that isn’t your fault – you and your passengers can be hurt.
Page 34: Driver Position
Driver Position This part describes the driver’s restraint system. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here is how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”...
Page 35 5. To make the lap part tight, pull down on the buckle The lap part of the belt should be worn low and snug on end of the belt as you pull up on the shoulder belt. the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones.
Page 36: Shoulder Belt Height Adjuster
Shoulder Belt Height Adjuster Before you begin to drive, move the shoulder belt adjuster to the height that is right for you. 1-30 To move it down, push down on the button and move the height adjuster to the desired position. You can move the adjuster up just by pushing up on the shoulder belt guide.
Page 37 What’s wrong with this? The shoulder belt is too loose. It will not give nearly as much protection this way. CAUTION: You can be seriously hurt if your shoulder belt is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should ﬁt against your body.
Page 38 What’s wrong with this? The belt is buckled in the wrong place. 1-32 CAUTION: You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones.
Page 39 What’s wrong with this? The belt is over an armrest. CAUTION: You can be seriously injured if your belt goes over an armrest like this. The belt would be much too high. In a crash, you can slide under the belt. The belt force would then be applied at the abdomen, not at the pelvic bones, and that could cause serious or fatal injuries.
Page 40 What’s wrong with this? The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-34 CAUTION: You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury.
Page 41 What’s wrong with this? The belt is twisted across the body. CAUTION: You can be seriously injured by a twisted belt. In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to ﬁx it.
Page 42: Safety Belt Use During Pregnancy
To unlatch the belt, just push the button on the buckle. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle.
Page 43: Right Front Passenger Position
The best way to protect the fetus is to protect the mother. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly.
Page 44: Rear Seat Passengers
Rear Seat Passengers Rear Seat Outside Passenger Positions It’s very important for rear seat passengers to buckle up! Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash.
Page 45 Lap-Shoulder Belt The positions next to the windows have lap-shoulder belts. Here’s how to wear one properly. 1. Pick up the latch plate and pull the belt across you. Don’t let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly.
Page 46 The lap part of the belt should be worn low and snug 3. To make the lap part tight, pull down on the buckle on the hips, just touching the thighs. In a crash, this end of the belt as you pull up on the shoulder part. applies force to the pelvic bones.
Page 47 The safety belt locks if there’s a sudden stop or a crash, or if you pull the belt very quickly out of the retractor. Each position next to the windows in the second row has a shoulder belt height adjuster. Move the shoulder belt adjuster to the height that is right for you.
Page 48: Center Rear Passenger Position
Center Rear Passenger Position Lap-Shoulder Belt If your vehicle has a bench seat, someone can sit in the center position. When you sit in the center seating position, you have a lap safety belt, which has no retractor. You also have a shoulder belt, which has a retractor.
Page 49 2. Insert the metal knob on the shoulder belt into the 3. To make the lap belt longer, tilt the latch plate and keyhole on the lap belt buckle as shown. Be sure to pull it along the belt. slide the shoulder belt part into the keyhole until it locks into place.
Page 50 To make the belt shorter, pull its free end as shown until the belt is snug 4. Buckle, position and release the lap-shoulder belt the same way as the other lap-shoulder belts. If the belt isn’t long enough, see Safety Belt Extender on page 1-46.
Page 51 Second Row Center Position 2. Attach the elastic cord to the comfort guide on the center passenger shoulder belt. For second row center position do the following: 1. Remove the elastic cord from under the head restraint of the second row driver’s side position. 1-45...
Page 52: Safety Belt Pretensioners
3. Be sure that the belt is not twisted and it lies ﬂat. The guide must be on top of the belt. 4. Buckle, position and release the safety belt as described in Center Rear Passenger Position on page 1-42. Make sure that the shoulder belt crosses the shoulder.
Page 53: Child Restraints
Child Restraints Older Children Older children who have outgrown booster seats should wear the vehicle’s safety belts. What is the proper way to wear safety belts? If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide.
Page 54 1-48 CAUTION: Never do this. Here two children are wearing the same belt. The belt can’t properly spread the impact forces. In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt is very close to the child’s face or neck?
Page 55 CAUTION: Never do this. Here a child is sitting in a seat that has a lap-shoulder belt, but the shoulder part is behind the child. If the child wears the belt in this way, in a crash the child might slide under the belt.
Page 56: Infants And Young Children
Infants and Young Children Everyone in a vehicle needs protection! This includes infants and all other children. Neither the distance traveled nor the age and size of the traveler changes the need, for everyone, to use safety restraints. In fact, the law in every state in the United States and in every Canadian province says children up to some age must be restrained while in a vehicle.
Page 57 CAUTION: (Continued) it. For example, in a crash at only 25 mph (40 km/h), a 12-lb. (5,5 kg) baby will suddenly become a 240-lb. (110 kg) force on a person’s arms. A baby should be secured in an appropriate restraint. CAUTION: Children who are up against, or very close to, any air bag when it inﬂates can be seriously...
Page 58 What are the different types of add-on child restraints? Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used.
Page 59: Child Restraint Systems
CAUTION: The body structure of a young child is quite unlike that of an adult or older child, for whom the safety belts are designed. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should.
Page 60 A rear-facing infant seat (B) provides restraint with the seating surface against the back of the infant. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1-54 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields.
Page 61 A booster seat (F-G) is a child restraint designed to improve the ﬁt of the vehicle’s safety belt system. Some booster seats have a shoulder belt positioner, and some high-back booster seats have a ﬁve-point harness. A booster seat can also help a child to see out the window. How do child restraints work? A child restraint system is any device designed for use in a motor vehicle to restrain, seat, or position...
Page 62: Where To Put The Restraint
When choosing a child restraint, be sure the child restraint is designed to be used in a vehicle. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may ﬁnd these instructions on the restraint itself or in a booklet, or both.
Page 63: Top Strap
Top Strap Some child restraints have a top strap, or “top tether.” It can help restrain the child restraint during a collision. For it to work, a top strap must be properly anchored to the vehicle. Some top strap-equipped child restraints are designed for use with or without the top strap being anchored.
Page 64 Top Strap Anchor Location Anchor the top strap to one of the following anchor points. Be sure to use an anchor point located on the same side of the vehicle as the seating position where the child restraint will be placed. If you have an adjustable head restraint, route the top strap under it.
Page 65 Second Row Outside Position Bench Seat Second Row Center Position Bench Seat without Third Row Seat 1-59...
Page 66 Your vehicle has top strap anchors already installed for the rear seating positions. An anchor bar for a top strap is located at the rear of the seat cushion for each second row outboard seating position. The anchor bar for the center position bench seat is located on the ﬂoor behind the second row seats.
Page 67 Second Row Center Position Bench Seat with Third Row Seat Folded Down If the vehicle has a third row seat and the seatback is folded, there is an anchor on the back of the third row seat for the second row center position bench seat. Third Row Passenger’s Side Outside Position There is also a top strap anchor for third row passenger’s side outside position.
Page 68 Lower Anchorages and Top Tethers for Children (LATCH System) Your vehicle has the LATCH system. You will ﬁnd anchors (A) in the second row outside passenger positions. 1-62 This system, designed to make installation of child restraints easier, does not use the vehicle’s safety belts. Instead, it uses vehicle anchors (A, B) and child restraint attachments to secure the restraints.
Page 69 In order to use the LATCH system in your vehicle, you need a child restraint designed for that system. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system has a label on the seatback.
Page 70: Securing A Child Restraint Designed For The Latch System
Securing a Child Restraint Designed for the LATCH System 1. Find the anchors for the seating position you want to use, where the bottom of the seatback meets the back of the seat cushion. 2. Put the child restraint on the seat. 3.
Page 71 If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-62. See Top Strap on page 1-57 if the child restraint has one. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in this position.
Page 72 3. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-66 4. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. If you are using a forward-facing child restraint, you may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt.
Page 73: Securing A Child Restraint In A Center Rear Seat Position
Securing a Child Restraint in a Center Rear Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-62. See Top Strap on page 1-57 if the child restraint has one. If your child restraint does not have the LATCH system, you will be using the lap-shoulder belt to secure the child restraint in the center rear seating position.
Page 74 1-68 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 5. To tighten the belt, pull its free end while you push down on the child restraint.
Page 75: Securing A Child Restraint In The Right Front Seat Position
Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for Children (LATCH System) on page 1-62. See Top Strap on page 1-57 if the child restraint has one. Your vehicle has a front passenger air bag.
Page 76 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. 1-70...
Page 77 5. To tighten the belt, pull up on the shoulder belt while you push down on the child restraint. You may ﬁnd it helpful to use your knee to push down on the child restraint as you tighten the belt. 6.
Page 78: Air Bag Systems
Air Bag Systems This part explains the frontal and side impact air bag systems. Your vehicle has air bags – a frontal air bag for the driver and another frontal air bag for the right front passenger. Your vehicle may also have a side impact air bag.
Page 79 CAUTION: (Continued) Frontal air bags for the driver and right front passenger are designed to deploy only in moderate to severe frontal and near frontal crashes. They aren’t designed to inﬂate at all in rollover, rear or low-speed frontal crashes, or in many side crashes.
Page 80 CAUTION: Anyone who is up against, or very close to, any air bag when it inﬂates can be seriously injured or killed. Air bags plus lap-shoulder belts offer the best protection for adults, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them.
Page 81: Where Are The Air Bags
Where Are the Air Bags? The driver’s frontal air bag is in the middle of the steering wheel. The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side. 1-75...
Page 82 If your vehicle has one, the driver’s side impact air bag is in the side of the driver’s seatback closest to the door. 1-76 If your vehicle has one, the right front passenger’s side impact air bag is in the side of the passenger’s seatback closest to the door.
Page 83: When Should An Air Bag Inﬂate
CAUTION: If something is between an occupant and an air bag, the bag might not inﬂate properly or it might force the object into that person causing severe injury or even death. The path of an inﬂating air bag must be kept clear. Don’t put anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air...
Page 84: What Makes An Air Bag Inﬂate
If your vehicle strikes something that will move or deform, such as a parked car, the threshold level will be higher. The driver’s and right front passenger’s frontal air bags are not designed to inﬂate in rollovers, rear impacts, or in many side impacts because inﬂation would not help the occupant.
Page 85: How Does An Air Bag Restrain
How Does an Air Bag Restrain? In moderate to severe frontal or near frontal collisions, even belted occupants can contact the steering wheel or the instrument panel. In moderate to severe side collisions, even belted occupants can contact the inside of the vehicle.
Page 86: What Will You See After An Air Bag Inﬂates
What Will You See After an Air Bag Inﬂates? After the air bag inﬂates, it quickly deﬂates, so quickly that some people may not even realize the air bag inﬂated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal air bag and the instrument panel for the right front passenger’s frontal air bag.
Page 87 In many crashes severe enough to inﬂate an air bag, windshields are broken by vehicle deformation. Additional windshield breakage may also occur from the right front passenger air bag. • Air bags are designed to inﬂate only once. After an air bag inﬂates, you’ll need some new parts for your air bag system.
Page 88: Restraint System Check
Servicing Your Air Bag-Equipped Vehicle Air bags affect how your vehicle should be serviced. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems.
Page 89: Replacing Restraint System Parts After A Crash
Replacing Restraint System Parts After a Crash CAUTION: A crash can damage the restraint systems in your vehicle. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible.
Page 90 NOTES 1-84...
Page 91: Features And Controls
Section 2 Keys ...2-3 Remote Keyless Entry System ...2-4 Remote Keyless Entry System Operation ...2-5 Doors and Locks ...2-8 Door Locks ...2-8 Power Door Locks ...2-9 Delayed Locking ...2-9 Programmable Automatic Door Locks ...2-10 Rear Door Security Locks ...2-10 Lockout Protection ...2-11 Leaving Your Vehicle ...2-11 Liftgate ...2-11 Windows ...2-13...
Page 92 Section 2 ® HomeLink Transmitter ...2-35 ® Programming the HomeLink Storage Areas ...2-39 Glove Box ...2-39 Cupholder(s) ...2-39 Cell Phone Storage Area ...2-39 Overhead Console ...2-39 Floor Console Storage Area ...2-40 Front Armrest Storage Area ...2-40 Features and Controls Rear Storage Area ...2-40 Transmitter ...2-35 Roof Rack System ...2-41 Convenience Net ...2-44...
Page 93: Keys
Keys CAUTION: Leaving children in a vehicle with the ignition key is dangerous for many reasons. A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Do not leave the keys in a vehicle with children.
Page 94: Remote Keyless Entry System
Your vehicle’s key can be used for the ignition as well as the driver’s door lock, the ﬂoor console, and the glovebox. If you need a new key, contact your dealer, who can obtain the correct key code. ® Your vehicle has the PASS-Key III vehicle theft system.
Page 95: Remote Keyless Entry System Operation
At times you may notice a decrease in range. This is normal for any remote keyless entry system. If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: •...
Page 96: Remote Alarm
If you would like to program the way the headlamps and parking lamps operate with remote unlock conﬁrmation, and your vehicle is equipped with the Driver Information Center (DIC), see DIC Vehicle Personalization on page 3-64. LOCK: To lock all doors, press LOCK. The LOCK button on the remote keyless entry transmitter will arm the content theft-deterrent system.
Page 97: Battery Replacement
Battery Replacement Under normal use, the battery in your remote keyless entry transmitter should last about three years. United States You can tell the battery is weak if the KEY FOB BATTERY LOW message appears in the message center. If you get this message, the battery in the key fob needs to be replaced.
Page 98: Doors And Locks
Doors and Locks Door Locks CAUTION: Unlocked doors can be dangerous. • Passengers — especially children — can easily open the doors and fall out of a moving vehicle. When a door is locked, the handle will not open it. You increase the chance of being thrown out of the vehicle in a crash if the doors are not locked.
Page 99 Power Door Locks The power door lock switch is located on the driver’s and front passenger’s doors next to the door handle. Press the front of the switch to lock all doors, or press the back of the switch to unlock all doors. The rear doors do not have power door lock switches.
Page 100: Programmable Automatic Door Locks
Programmable Automatic Door Locks All of the doors will automatically lock when all doors are closed, the engine is running and the shift lever is shifted out of PARK (P). All of the doors will automatically unlock when the shift lever is shifted into PARK (P).
Page 101: Canceling The Rear Door Security Locks
Canceling the Rear Door Security Locks 1. Unlock and open the rear door from the outside. 2. Push the lever down to disengage the safety lock. 3. Close the door. 4. Repeat Steps 1 through 3 for the other rear door lock.
Page 102 Liftgate Release Liftgate Handle 2-12 Your vehicle is equipped with a liftgate release touchpad, located on the inner side of the liftgate handle. To open the liftgate using the touchpad, do the following: 1. Put the vehicle in PARK (P). 2.
Page 103: Windows
Windows CAUTION: Leaving children in a vehicle with the windows closed is dangerous. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather.
Page 104: Power Windows
Power Windows Switches on the driver’s door armrest control each of the windows when the ignition is in ON, ACCESSORY, or when retained accessory power is active. See “Retained Accessory Power (RAP)” under Ignition Positions on page 2-20 for more information. In addition, each passenger’s door has a window switch.
Page 105: Theft-Deterrent Systems
Sun Visors To block out glare you can swing down the visors. You can also remove them from the center mount and swing them to the side. There may be an extension on the inboard side of the sun visors. Pull the extension out to block out glare.
Page 106: Arming With The Power Lock Switch
Arming with the Power Lock Switch Your alarm system will arm when you use either power door lock switch to lock the doors while any door or the liftgate is open and the key is removed from the ignition. The security light will start ﬂashing to let you know the system is armed.
Page 107 ® PASS-Key ® Your PASS-Key III system operates on a radio frequency subject to Federal Communications Commission (FCC) Rules and with Industry Canada. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1.
Page 108 If the engine still does not start, and the key appears to be undamaged, try another ignition key. At this time, you may also want to check the fuse. See Fuses and Circuit Breakers on page 5-109. If the engine still does not start with the other key, your vehicle needs service.
Page 109: Starting And Operating Your Vehicle
Starting and Operating Your Vehicle New Vehicle Break-In Notice: Your vehicle does not need an elaborate “break-in.” But it will perform better in the long run if you follow these guidelines: • If you have all-wheel drive, keep your speed at 55 mph (88 km/h) or less for the ﬁrst 500 miles (805 km).
Page 110: Ignition Positions
Ignition Positions With the key in the ignition, you can turn the key to four different positions. A (OFF): This is the only position in which you can remove the key. This position locks the steering wheel, ignition and transaxle. 2-20 Notice: If your key seems stuck in OFF and you can’t turn it, be sure you are using the correct key;...
Page 111: Retained Accessory Power (Rap)
Retained Accessory Power (RAP) With RAP, the power windows, the audio system, the sunroof and the Automatic Level Control will continue to work up to 10 minutes after the ignition key is turned to OFF and none of the doors are opened. Starting Your Engine Move your shift lever to PARK (P) or NEUTRAL (N).
Page 112: Engine Coolant Heater
Engine Coolant Heater Your vehicle may have an engine coolant heater. In very cold weather, 0°F ( 18°C) or colder, the engine coolant heater can help. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle.
Page 113: Automatic Transaxle Operation
Automatic Transaxle Operation Maximum engine speed is limited when you’re in PARK (P) or NEUTRAL (N), to protect driveline components from improper operation. There are several different positions for your shift lever. PARK (P): This gear position locks your front wheels. It is the best position to use when you start your engine because your vehicle cannot move easily.
Page 114 REVERSE (R): Use this gear to back up. Notice: Shifting to REVERSE (R) while your vehicle is moving forward could damage the transaxle. The repairs would not be covered by your warranty. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If You Are Stuck: In Sand, Mud, Ice or Snow on...
Page 115: Warm-Up Shift
Warm-Up Shift Your vehicle has a computer controlled transaxle designed to warm up the engine faster when the outside temperature is 35°F (2°C) or colder. You may notice that the transaxle will shift at a higher vehicle speed until the engine is warmed up. This is a normal condition designed to provide heat to the passenger compartment and defrost the windows more quickly.
Page 116 Parking Brake The parking brake is located on the driver’s side under the instrument panel. To set the parking brake, hold the regular brake pedal down with your right foot and push down on the parking brake pedal with your left foot. If the ignition is on, the brake system warning light will come on.
Page 117: Shifting Into Park (P)
Shifting Into Park (P) 2. To move the shift lever into PARK (P), do the following: CAUTION: It can be dangerous to get out of your vehicle if the shift lever is not fully in PARK (P) with the parking brake ﬁrmly set. Your vehicle can roll.
Page 118: Leaving Your Vehicle With The Engine Running
2.2. Move the lever up as far as it will go. 3. Turn the ignition key to LOCK. 4. Remove the key and take it with you. If you can leave your vehicle with the ignition key in your hand, your vehicle is in PARK (P). 2-28 Leaving Your Vehicle With the Engine Running...
Page 119: Torque Lock
Torque Lock If you are parking on a hill and you do not shift your transaxle into PARK (P) properly, the weight of the vehicle may put too much force on the parking pawl in the transaxle. You may ﬁnd it difficult to pull the shift lever out of PARK (P).
Page 120: Parking Over Things That Burn
Parking Over Things That Burn CAUTION: Things that can burn could touch hot exhaust parts under your vehicle and ignite. Do not park over papers, leaves, dry grass or other things that can burn. 2-30 Engine Exhaust CAUTION: Engine exhaust can kill. It contains the gas carbon monoxide (CO), which you can not see or smell.
Page 121: Running Your Engine While You Are Parked
Running Your Engine While You Are Parked It is better not to park with the engine running. But if you ever have to, here are some things to know. CAUTION: Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle.
Page 122: Mirrors
Mirrors Manual Rearview Mirror To reduce glare from lights behind you, pull the lever toward you to for the night position. To return the mirror to the day position, push the lever away from you. The mirror’s two outer buttons operate the lights on the bottom sides of the mirror.
Page 123: Onstar System
Outside Convex Mirror Your passenger’s side mirror is convex. A convex mirror’s surface is curved so you can see more from the driver’s seat. CAUTION: A convex mirror can make things (like other vehicles) look farther away than they really are. If you cut too sharply into the right lane, you could hit a vehicle on your right.
Page 124 ® OnStar Services One of the following plans is normally included for a speciﬁc duration with each vehicle equipped with ® OnStar . You can upgrade or extend your OnStar service plan to meet your needs. Safe and Sound Plan •...
Page 125: Homelink Transmitter
® HomeLink Transmitter HomeLink, a combined universal transmitter and receiver, provides a way to replace up to three hand held transmitters used to activate devices such as gate operators, garage door openers, entry door locks, security systems and home lighting. Additional HomeLink information can be found on the internet at www.homelink.com or by calling 1 800 355 3515.
Page 126 Keep the original transmitter for use in other vehicles as ® well as for future HomeLink programming. It is also recommended that upon the sale of the vehicle, ® the programmed HomeLink buttons should be erased for security purposes. Refer to “Erasing HomeLink Buttons”...
Page 127: Gate Operator And Canadian Programming
6. Locate in the garage, the garage door opener receiver (motor-head unit). Locate the “Learn” or “Smart” button. This can usually be found where the hanging antenna wire is attached to the motor-head unit. 7. Firmly press and release the “Learn” or “Smart” button.
Page 128: Using Homelink
® Using HomeLink Press and hold the appropriate HomeLink least half of a second. The indicator light will come on while the signal is being transmitted. ® Erasing HomeLink Buttons To erase programming from the three buttons do the following: 1.
Page 129: Storage Areas
Storage Areas Glove Box If the glove box has a lock, put your key into the lock and turn the key counterclockwise. To open the glovebox, pull the latch release. The glove box door has a detent to prevent the door from lowering too far.
Page 130: Sunglasses Storage Compartment
Sunglasses Storage Compartment To open the sunglasses storage compartment in the overhead console, press the release button. Then pull the compartment down to the full open position. Floor Console Storage Area The ﬂoor console storage contains two cupholders, an ashtray and a cellular phone storage compartment with a cigarette lighter/accessory power outlet.
Page 131: Roof Rack System
Roof Rack System CAUTION: If you try to carry something on top of your vehicle that is longer or wider than the luggage carrier — like paneling, plywood, a mattress and so forth — the wind can catch it as you drive along.
Page 132 Notice: Loading cargo on the luggage carrier that weighs more than 220 lbs (100 kg) or hangs over the rear or sides of the vehicle may damage your vehicle. Load cargo so that it rests on the slats as far forward as possible and against the side rails, making sure to fasten it securely.
Page 133 To adjust the crossrail(s), the sunroof stop (A) must be removed. To remove the sunroof stop, do the following: 1. Find the tool (B) located in a bag in the glovebox labeled “tool kit-acsry”. 2. Use the tool to remove the screw located in the side rail assembly in front of the front crossrail.
Page 134: Convenience Net
Convenience Net Your vehicle may have a convenience net. The convenience net is designed to help keep small loads, like grocery bags, from falling over. Install the convenience net at the rear of your vehicle, just inside the liftgate/tailgate opening. Attach both the upper and lower hooks to the loops on either side of the liftgate opening.
Page 135 Removing the Extended Rear Convenience Center 1. Make sure that all items have been removed from the top and the inside of the rear convenience center. 2. Remove the carpeted mat from the vehicle. 3. Lift the handle(s) on the top of the lid to open the rear storage bin.
Page 136 5. Lift the rear bin into the back of the vehicle. Place the rear bin over the center T-shaped wall on the forward bin. Push down to secure. Align the rear bin over the rear mounting bolts. 6. Put the nuts back onto the mounting bolts and tighten.
Page 137 Replacing the Rear Convenience Center on Vehicles with the Third Row Stowable Seat 1. Make sure that all items have been removed from the rear of the vehicle. 2. Lift the bin into the back of the vehicle. Align the bin over the rear mounting bolts.
Page 138: Sunroof
Sunroof If your vehicle has a sunroof, the switch is located between the sun visors. 2-48 The sunroof switch will only work when the ignition is on or when the ignition is off and retained accessory power is active. See “Retained Accessory Power” under Ignition Positions on page 2-20 for more information.
Page 139: Vehicle Personalization
Vehicle Personalization Memory Seat If your vehicle has this feature, the controls are located on the driver’s door panel and are used to store and recall the driver’s seat position and outside rearview mirror position. To store a seat position, do the following: 1.
Page 140 NOTES 2-50...
Page 141: Instrument Panel
Section 3 Instrument Panel Overview ...3-4 Hazard Warning Flashers ...3-6 Other Warning Devices ...3-7 Horn ...3-7 Tilt Wheel ...3-7 Turn Signal/Multifunction Lever ...3-8 Exterior Lamps ...3-14 Interior Lamps ...3-16 Instrument Panel Switchbank ...3-21 Head-Up Display (HUD) ...3-21 Ultrasonic Rear Parking Assist (URPA) ...3-24 Accessory Power Outlets ...3-27 Ashtrays and Cigarette Lighter ...3-28 Climate Controls ...3-28...
Page 142 Section 3 Service Vehicle Soon Message ...3-57 Program Mode Message ...3-58 Remote Keyless Entry Transmitter Battery Low Warning Message ...3-58 Parking Lamp Warning Message ...3-59 Highbeam Out Warning Message ...3-59 Driver Information Center (DIC) ...3-60 DIC Controls and Displays ...3-62 DIC Vehicle Personalization ...3-64 Audio System(s) ...3-73 Setting the Time ...3-73...
Page 143 NOTES...
Page 144: Instrument Panel Overview
Instrument Panel Overview...
Page 145 The main components of the instrument panel are the following: A. Exterior/Interior Lamps Control. See Exterior Lamps on page 3-14 and Interior Lamps on page 3-16. B. Turn Signal/Multifunction Lever. See Turn Signal/Multifunction Lever on page 3-8. C. Hazard Warning Flasher Switch. See Hazard Warning Flashers on page 3-6.
Page 146: Hazard Warning Flashers
Hazard Warning Flashers Your hazard warning ﬂashers let you warn others. They also let police know you have a problem. Your front and rear turn signal lamps will ﬂash on and off. The hazard warning ﬂasher button is located on top of the steering column.
Page 147: Other Warning Devices
Other Warning Devices If you carry reﬂective triangles, you can set one up at the side of the road about 300 feet (100 m) behind your vehicle. Horn You can sound the horn by pressing the center of your steering wheel. Tilt Wheel A tilt wheel allows you to adjust the steering wheel before you drive.
Page 148: Turn Signal/Multifunction Lever
Turn Signal/Multifunction Lever The lever on the left side of the steering column includes the following: • Turn and Lane-Change Signals • Headlamp High/Low-Beam Changer • Flash-to-Pass • Windshield Wipers • Windshield Washer • Cruise Control Turn and Lane-Change Signals The turn signal has two upward (for right) and two downward (for left) positions.
Page 149 If you have a trailer towing option with added wiring for the trailer lamps, the signal indicator will ﬂash at a normal rate even if a turn signal bulb is burned out. Check the front and rear turn signal lamps regularly to make sure they are working.
Page 150: Windshield Washer
Remember that damaged wiper blades may prevent you from seeing well enough to drive safely. To avoid damage, be sure to clear ice and snow from the wiper blades before using them. If they are frozen to the windshield, carefully loosen or thaw them. If your blades do become damaged, get new blades or blade inserts.
Page 151: Cruise Control
To wash the rear window while the rear wiper is already on, push the bottom of the switch. Push in the top of the switch to continue the intermittent wiper cycle after the washing cycle is completed. Cruise Control CAUTION: •...
Page 152 Resuming a Set Speed Suppose you set your cruise control at a desired speed and then you apply the brake. This, of course, shuts off the cruise control. But you do not need to reset it. Once you are going about 25 mph (40 km/h) or more, you can move the cruise control switch from ON to resume/accelerate (R/A) brieﬂy.
Page 153 Passing Another Vehicle While Using Cruise Control Use the accelerator pedal to increase your speed. When you take your foot off the pedal, your vehicle will slow down to the cruise control speed you set earlier. Using Cruise Control on Hills How well your cruise control will work on hills depends upon your speed, load and the steepness of the hills.
Page 154: Exterior Lamps
Exterior Lamps The control on the left side of the steering column operates the exterior lamps. The exterior lamp control has three positions: AUTO (Automatic Headlamp Control/Off): Turning the control to this position will activate the automatic headlamps when it is dark enough outside and turn off all lamps and lights during the day except for the Daytime Running Lamps (DRL).
Page 155: Automatic Headlamp System
Daytime Running Lamps (DRL) Daytime Running Lamps (DRL) can make it easier for others to see the front of your vehicle during the day. DRL can be helpful in many different driving conditions, but they can be especially helpful in the short periods after dawn and before sunset.
Page 156: Interior Lamps
Fog Lamps The fog lamp button is located on the exterior lamp control. Push the FOG PUSH button to turn the fog lamps on. The FOG light, located next to the fog lamp button, will come on to indicate when the fog lamps are on. To turn off the fog lamps, press the fog lamp button or turn the ignition off.
Page 157: Interior Lamps Control
Interior Lamps Control OFF: Turn the control to this position to turn off the interior lamps. DOOR: Turn the control to this position to turn on the interior lamps while any door is opened and while the ignition key is removed from the ignition. ON: Turn the control to this position to turn on the interior lamps.
Page 158: Entry Lighting
Entry Lighting If your vehicle has entry lighting, the interior of your vehicle will illuminate for 25 seconds so you can see inside your vehicle before you enter. To activate entry lighting, do one of the following: • Unlock a door using the key when the interior lamp control is in the DOOR position, and when the ignition is in OFF •...
Page 159: Exit Lighting
Exit Lighting If your vehicle is equipped with exit lighting, the interior lamps will come on for about 30 seconds whenever you remove the key from the ignition if the following conditions are met: • The vehicle is in PARK (P) •...
Page 160: Battery Run-Down Protection
Front Reading Lamps There are two reading lamps located on the rearview mirror. To turn either reading lamp on or off, press the button located next to each lamp. These lamps will come on each time you open the doors, if the interior lamp control is in the ON or DOOR position.
Page 161: Instrument Panel Switchbank
Instrument Panel Switchbank There is an instrument panel switchbank located below the comfort controls. It contains switches or blanks that will vary with the options that are on your vehicle. The switches you may have are: • Rear Window Wiper/Washer. See Turn Signal/Multifunction Lever on page 3-8.
Page 162 The Head-Up Display also displays the following lights and messages when they appear on the instrument panel cluster: • Turn Signal Indicators. See Turn Signal/Multifunction Lever on page 3-8. • High-Beam Indicator. See Turn Signal/Multifunction Lever on page 3-8. • Low-Fuel Warning Message.
Page 163 Notice: If you try to use the HUD image as a parking aid, you may misjudge the distance and damage your vehicle. Do not use the HUD image as a parking aid. The HUD controls are located to the left of the steering wheel on the instrument panel.
Page 164 When you ﬁrst start the vehicle the display will show BUICK and the Buick logo for a few seconds. If it is cold outside, this display may stay on for up to a minute. Clean the inside of the windshield as needed to remove any dirt or ﬁlm that reduces the sharpness or clarity...
Page 165 CAUTION: Even with the Ultrasonic Rear Park Assist system, the driver must check carefully before backing up. The system does not operate above typical backing speeds of 3 mph (5 km/h) while parking. And, the system does not detect objects that are more than 5 feet (1.5 meters) behind the vehicle.
Page 166: How The System Works
How the System Works Unless disabled, the URPA will turn on automatically when the shift lever is moved into REVERSE (R). When the system turns on, the three lights on the display will illuminate for one and a half seconds to let you know that the system is working.
Page 167: Accessory Power Outlets
Accessory Power Outlets With accessory power outlets you can plug in electrical equipment such as a cellular telephone or CB radio. There is one front power outlet/cigarette lighter located on the ﬂoor console in the cell phone storage compartment. There are also two rear power outlets. One is located in the rear of the ﬂoor console below the vents.
Page 168: Climate Controls
Ashtrays and Cigarette Lighter The ashtray is located on the ﬂoor console closest to the instrument panel. Lift the lid to expose the ashtray. To remove the ashtray, lift it up. The cigarette lighter is located on the ﬂoor console in the cell phone storage compartment closest to the driver’s seat.
Page 169 Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets. (Bi-Level): This mode directs half of the air to the instrument panel outlets, then directs the remaining air to the ﬂoor outlets.
Page 170: Defogging And Defrosting
A/C (Air Conditioning): Press this button to turn the air-conditioning system on or off. When A/C is pressed, an indicator light in the button will come on to let you know that air conditioning is activated. You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again.
Page 171: Rear Window Defogger
Turn the right knob to select the defog or defrost mode. (Defog): This mode directs air to the windshield and the ﬂoor outlets. When you select this mode, the system turns off recirculation and runs the air-conditioning compressor unless the outside temperature is at or below freezing.
Page 172: Dual Climate Control System
Dual Climate Control System Your vehicle may have a dual climate control system. With this system you can control the heating, cooling, and ventilation for your vehicle. Operation Turn the right knob clockwise or counterclockwise to direct the airﬂow inside your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 173 (Recirculation): This mode keeps outside air from coming in the vehicle. It can be used to prevent outside air and odors from entering your vehicle or help heat or cool the air inside your vehicle more quickly. Press this button to turn the recirculation mode on or off. When the button is pressed, an indicator light will come on.
Page 174 Defogging and Defrosting Fog on the inside of windows is a result of high humidity, or moisture, condensing on the cool window glass. This can be minimized if the climate controls system is used properly. There are two modes to clear fog or frost from your windshield.
Page 175: Dual Automatic Climate Control System
Dual Automatic Climate Control System Your vehicle may have the dual automatic climate control system. With this system you can control the heating, cooling, and ventilation for your vehicle. Automatic Operation AUTO (Automatic): When the driver’s temperature knob is pressed to select AUTO and the temperature is set, the system will automatically control the inside temperature, the air delivery and the fan speed.
Page 176: Manual Operation
Manual Operation MODE: Press this button to manually change the direction of airﬂow in your vehicle; keep pressing the button until the desired mode appears on the display. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets.
Page 177 You may notice a slight change in engine performance when the air-conditioning compressor shuts off and turns on again. This is normal. The system is designed to make adjustments to help with fuel economy while still maintaining the selected temperature. On hot days, open the windows to let hot inside air escape;...
Page 178: Outlet Adjustment
Rear Window Defogger The rear window defogger uses a warming grid to remove fog from the rear window. < REAR: Press this button to turn the rear window defogger on or off. An indicator light in the button will come on to let you know that the rear window defogger is activated.
Page 179: Warning Lights, Gages And Indicators
Warning Lights, Gages and Indicators This part describes the warning lights and gages that may be on your vehicle. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement.
Page 180: Instrument Panel Cluster
Instrument Panel Cluster Your instrument panel cluster is designed to let you know at a glance how your vehicle is running. You’ll know how fast you’re going, how much fuel you’re using, and many other things you’ll need to drive safely and economically. The indicator warning lights and gages are explained on the following pages.
Page 181: Speedometer And Odometer
Speedometer and Odometer Your speedometer lets you see your speed in both miles per hour (mph) and kilometers per hour (km/h). Your odometer shows how far your vehicle has been driven, in either miles (used in the United States) or kilometers (used in Canada). However, a Canadian odometer will remain in metric units only.
Page 182: Retro-Active Reset
Retro-Active Reset The trip odometer has a feature called retro-active reset. This feature can be used to set the trip odometer to the number of miles or kilometers driven since the ignition was last turned on. This can be used if you forget to reset your trip odometer at the beginning of a trip.
Page 183: Safety Belt Reminder Light
Safety Belt Reminder Light When the key is turned to ON or START, a chime will come on for several seconds to remind people to fasten their safety belts. The safety belt light will also come on and stay on for several seconds.
Page 184: Brake System Warning Light
The air bag readiness light should ﬂash for a few seconds when you turn the ignition key to ON. If the light doesn’t come on then, have it ﬁxed so it will be ready to warn you if there is a problem. Brake System Warning Light When the ignition is on, the brake system warning light will come on when you set your parking brake.
Page 185: Anti-Lock Brake System Warning Light
Anti-Lock Brake System Warning Light United States Your vehicle may have an anti-lock brake system warning light. If it does, the light should come on for a few seconds when you turn the ignition key to ON. If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off.
Page 186: Engine Coolant Temperature Gage
Engine Coolant Temperature Gage United States This gage shows the engine coolant temperature. If the gage pointer moves into the red area, your engine is too hot! It means that your engine coolant has overheated. If you have been operating your vehicle under normal driving conditions, you should pull off the road, stop your vehicle and turn off the engine as soon as possible.
Page 187 This system is called OBD II (On-Board Diagnostics-Second Generation) and is intended to assure that emissions are at acceptable levels for the life of the vehicle, helping to produce a cleaner environment. The SERVICE ENGINE SOON or CHECK ENGINE light comes on to indicate that there is a problem and service is required.
Page 188: If The Light Is Flashing
If the Light Is Flashing The following may prevent more serious damage to your vehicle: • Reducing vehicle speed. • Avoiding hard accelerations. • Avoiding steep uphill grades. • If you are towing a trailer, reduce the amount of cargo being hauled as soon as it is possible. If the light stops ﬂashing and remains on steady, see “If the Light Is On Steady”...
Page 189: Fuel Gage
Emissions Inspection and Maintenance Programs Some state/provincial and local governments have or may begin programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Here are some things you need to know in order to help your vehicle pass an inspection: Your vehicle will not pass this inspection if the SERVICE ENGINE SOON or CHECK ENGINE light is on or not...
Page 190: Message Center
Here are four things that some owners ask about. All these things are normal and do not indicate that anything is wrong with the fuel gage. • At the gas station, the gas pump shuts off before the gage reads full. •...
Page 191: Traction Active Message
Traction Active Message United States If your vehicle has the traction control system, the TRACTION ACTIVE message will appear when the traction control system is limiting wheel spin. You may feel or hear the system working, but this is normal. Slippery road conditions may exist if this message appears, so adjust your driving accordingly.
Page 192: Charging System Indicator Message
Charging System Indicator Message The charging system battery symbol will come on in the message center when you turn on the ignition as a check to show you it is working. It will remain on as long as the engine is not running. It should go out once the engine is running.
Page 193: Maintenance Schedule
When the engine is running and this message appears, the engine oil level may be too low. There may also be another problem causing low oil pressure. CAUTION: Do not keep driving if the oil pressure is low. If you do, your engine can become so hot that it catches ﬁre.
Page 194: Low Tire Message
Low Tire Message United States Your vehicle may have the check tire pressure system which can alert you to a large change in the pressure of one tire. After the system has been properly calibrated, the low tire pressure message will come on and a chime will sound if a pressure difference, or low pressure, is detected in one tire.
Page 195 ® PASS-Key III Security Message United States If you are ever driving and this message comes on and stays on, you will be able to restart your engine if you turn it off. ® Your PASS-Key III system, however, is not working properly and must be serviced by your dealer.
Page 196: Low Washer Fluid Warning Message
Low Washer Fluid Warning Message United States If your washer ﬂuid is low, the warning message will come on and stay on until you add washer ﬂuid. See Windshield Washer Fluid on page 5-37 for adding washer ﬂuid instructions. If the warning message is still on after adding ﬂuid, you need to reset the warning message.
Page 197: Low Brake Fluid Warning Message
Low Brake Fluid Warning Message United States If your brake ﬂuid is low, the warning message will come on and stay on until you add brake ﬂuid. The brake system warning light will also be illuminated. If this message appears, the brakes need attention. You should have your vehicle serviced immediately.
Page 198: Program Mode Message
Program Mode Message United States If you receive this message, your vehicle is in program mode. If your vehicle is equipped with the Driver Information Center (DIC), you are ready to begin programming your vehicle’s customization features. See DIC Vehicle Personalization on page 3-64 for more information.
Page 199: Parking Lamp Warning Message
Parking Lamp Warning Message United States If you receive this message, one or both of the vehicle’s parking lamp bulbs needs replacement. See Bulb Replacement on page 5-50 for bulb replacement instructions. Highbeam Out Warning Message Canada United States If you receive this message, one or both of the vehicle’s high-beam headlamp bulbs needs replacement.
Page 200: Driver Information Center (Dic)
Driver Information Center (DIC) If your vehicle is equipped with the Driver Information Center (DIC), the display is located on the instrument panel cluster in the tachometer gage. The DIC will show information about the vehicle and the surroundings. The DIC is capable of displaying English or French. See DIC Controls and Displays on page 3-62 to change the display from English to metric.
Page 201 Manual Compass Calibration If the compass appears erratic and the calibration symbol does not appear, you must manually put the compass into the calibration mode. To get into this mode, do the following: 1. Turn the ignition on and cycle the DIC to the compass/temperature mode.
Page 202 When the ignition is turned to ON or START, the DIC will display the following: BUICK: BUICK will be displayed for three seconds. DRIVER #: This message will be displayed for another three seconds after BUICK appears in the display.
Page 203 FUEL USED: The fuel used display will show you how much fuel has been used since the last time it was reset. To reset the fuel used to zero, press and hold the SET button while the fuel used is displayed on the DIC and until the display goes to zero.
Page 204: Dic Vehicle Personalization
DIC Vehicle Personalization The DIC is used to program the choices of two drivers. The drivers are recognized as DRIVER 1 or DRIVER 2 in the DIC display. You will let the DIC know which driver you are by using your remote keyless entry transmitter. Each remote keyless entry transmitter was pre-programmed to belong to DRIVER 1 or DRIVER 2.
Page 205: Interior Lighting Delay
Headlamp Exit Delay This feature allows you to customize the headlamps and parking lamps. This feature can be programmed to one of the following modes: OFF: The headlamps and parking lamps will not turn on at the same instant that the ignition is turned to OFF. 15: The headlamps and parking lamps will stay on for 15 seconds when the ignition is turned to OFF.
Page 206: Interior Lighting On
Your vehicle was originally programmed to ON. The mode may have been changed since then. To determine the current mode, or to change the mode, do the following: 1. Follow the instructions for “Entering Programming Mode” listed previously. 2. Press the MODE button until INTERIOR LIGHTING DELAY appears on the DIC.
Page 207: Auto Door Lock/Unlock
Auto Door Lock/Unlock The doors will automatically lock when the vehicle is shifted out of PARK (P). For automatic unlocking, you can program your vehicle to one of the following modes: OFF: When the shift lever is put in PARK (P), your doors will not unlock automatically.
Page 208: Delayed Locking
Delayed Locking The delayed locking feature can be programmed to one of the following modes: ON: Lock your vehicle using the power door lock switch or the remote keyless entry transmitter while any door is opened, you will hear three chimes and the doors will not lock.
Page 209: Remote Door Unlock
Remote Door Unlock The remote door unlock feature can be programmed to one of the following modes: DRIVER/ALL: With the ﬁrst press of UNLOCK on the remote keyless entry transmitter, the driver’s door will unlock, and with the second press of UNLOCK, within ﬁve seconds of the ﬁrst press, all passenger’s doors will unlock.
Page 210: Lock Feedback
2. Follow the instructions for programming HEADLAMP EXIT DELAY earlier in this section, to make sure which mode it is programmed to. 3. Press the SET button until UNLOCK FEEDBACK appears on the DIC. 4. Press the MODE button until the arrow is before LIGHTS or OFF.
Page 211: Seat Recall
Seat Recall The seat recall feature can be programmed to one of the following modes: ON: The previously programmed memory seat position will be recalled when the UNLOCK button is pressed on the remote keyless entry transmitter. OFF: No memory seat position will be recalled when you press the UNLOCK button on the remote keyless entry transmitter.
Page 212: Tilt Mirror
Tilt Mirror The tilt mirror feature can be programmed to one of the following modes: ON: The passengers side outside rearview mirror will tilt down towards the curb when the vehicle is shifted to REVERSE (R) and returns to its previous position when the vehicle is shifted out of REVERSE (R).
Page 213: Audio System(S)
Audio System(s) Notice: Before you add any sound equipment to your vehicle – like a tape player, CB radio, mobile telephone or two-way radio – be sure you can add what you want. If you can, it’s very important to do it properly.
Page 214: Radio With Cd
Radio with CD Radio Data System (RDS) Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, your radio can do the following: •...
Page 215: Playing The Radio
Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOL (Volume): Turn this knob to increase or to decrease the volume. SCV (Speed-Compensated Volume): With SCV, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 216: Setting Preset Stations
Setting Preset Stations The six numbered pushbuttons let you return to your favorite stations. You can set up to 30 stations (six FM1, six FM2 and six AM, six XM1 and six XM2 (48 contiguous US states, if equipped), by performing the following steps: 1.
Page 217: Rds And Xm
Adjusting the Speakers (Balance/Fade) AUDIO: To adjust the balance between the right and the left speakers, push and release AUDIO until BAL appears on the display. Then turn the AUDIO knob to move the sound toward the right or the left speakers. A bar graph with indicators will show how the sound is balanced.
Page 218: Rds Messages
SCAN: You can scan the stations within a PTY by performing the following: 1. Press P-TYP to activate program type select mode. The PTY symbol will appear on the display. 2. Turn the AUDIO knob to select a PTY. 3. Once the desired PTY is displayed, press and hold either SEEK arrow, and the radio will begin scanning the stations in the PTY.
Page 219 TRAF (Traffic): If TRAF appears on the display, the tuned station broadcasts traffic announcements. To receive the traffic announcement from the tuned station, press this button. Brackets will be displayed around TRAF and when a traffic announcement comes on the tuned radio station you will hear it. If the current tuned station does not broadcast traffic announcements, press this button and the radio will seek to a station that does.
Page 220: Radio Messages
Radio Messages CAL (CALIBRATE): Your audio system has been calibrated for your vehicle from the factory. If CAL appears on the display it means that your radio has not been conﬁgured properly for your vehicle and must be returned to the dealership for service.
Page 221 Radio Display Message CH Unavail Channel no longer available No Info Artist Name/Feature not available No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active XM™...
Page 222 Radio Display Message Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr Hardware failure 3-82 XM™ Radio Messages (cont’d) Condition If you tune to channel 0, you will see this message alternating with your XM Radio 8 digit radio ID label.
Page 223: Playing A Cd
Playing a CD With the ignition on, insert a CD partway into the slot, label side up. The player will pull it in and the CD should begin playing. If you want to insert a CD while the ignition or the radio is off, ﬁrst press the eject or DISP button.
Page 224 © ¨ SEEK : Press the left arrow to go to the start of the current track if more than eight seconds have played. Press the right arrow to go to the next track. If you hold the arrow or press it more than once, the player will continue moving backward or forward through the CD.
Page 225: Radio With Cassette And Cd
Listening to a DVD Your vehicle may have a Rear Seat Entertainment System. If your vehicle has this system and a DVD is playing, the DVD symbol will appear on the radio display indicating that the DVD is available and can be listened through your vehicles speakers.
Page 226: Contiguous Us States
This system relies upon receiving speciﬁc information from these stations and will only work when the information is available. In rare cases, a radio station may broadcast incorrect information that will cause the radio features to work improperly. If this happens, contact the radio station.
Page 227 To change the default on the display, press this button until you see the display you want, then hold the button until the display ﬂashes. The selected display will now be the default. Finding a Station BAND: Press this button to switch between FM1, FM2, or AM, or XM1 or XM2 (48 contiguous US states, if equipped).
Page 228 Setting the Tone (Bass/Treble) AUDIO: Push and release this knob until BASS, MID, or TREBLE appears on the display. Then turn the AUDIO knob to increase or to decrease. If a station is weak or noisy, you may want to decrease the treble. To adjust bass, midrange, or treble to the middle position, select BASS, MID, or TREBLE.
Page 229 Finding a Program Type (PTY) Station (RDS and XM™) To select and ﬁnd a desired PTY perform the following: 1. Press P-TYP to activate program type select mode. The P-TYPE symbol will appear on the display. 2. Turn the AUDIO knob to select a PTY. 3.
Page 230 RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display. You will hear the announcement, even if the volume is muted or a cassette tape or CD is playing. If a cassette tape or CD is playing, play will stop during the announcement.
Page 231 Radio Messages CAL (CALIBRATE): Your audio system has been calibrated for your vehicle from the factory. If CAL appears on the display it means that your radio has not been conﬁgured properly for your vehicle and must be returned to the dealership for service.
Page 232 Radio Display Message CH Unavail Channel no longer available No Info Artist Name/Feature not available No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational message available Not Found No channel available for the chosen category XM Locked Theft lock active Radio ID...
Page 233: Playing A Cassette Tape
Radio Display Message Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr Hardware failure Playing a Cassette Tape The longer side with the tape visible should face to the right. If the ignition and the radio are on, the tape can be inserted and will begin playing.
Page 234: Cassette Tape Messages
© ¨ SEEK : Your tape must have at least three seconds of silence between each selection for seek to work. Press the left or the right arrow to go to the previous or to the next selection on the tape. SEEK and a negative or positive number will be displayed.
Page 235: Cd Adapter Kits
CD Adapter Kits It is possible to use a portable CD player with your cassette tape player after activating the bypass feature on your tape player. To activate the bypass feature, use the following steps: 1. Turn the ignition on. 2.
Page 236 (Forward): Press and hold this pushbutton to quickly advance within a track. You will hear sound at a reduced volume. Release the pushbutton to play the passage. The display will show the elapsed time of the track. 4 RDM (Random): Press this pushbutton to hear the tracks in random, rather than sequential, order.
Page 237 CD Messages CHECK CD: If this message appears on the display, it could be for one of the following reasons: • It is very hot. When the temperature returns to normal, the CD should play. • You are driving on a very rough road. When the road becomes smoother, the CD should play.
Page 238: Radio With Six-Disc Cd
Radio with Six-Disc CD Radio Data System (RDS) Your audio system is equipped with a Radio Data System (RDS). RDS features are available for use only on FM stations that broadcast RDS information. With RDS, your radio can do the following: •...
Page 239 Playing the Radio PWR (Power): Push this knob to turn the system on and off. VOLUME: Turn this knob to increase or to decrease volume. AUTO VOL (Automatic Volume): Your system has a feature called automatic volume. With this feature, your audio system adjusts automatically to make up for road and wind noise as you drive.
Page 240 To scan preset stations, press and hold either SCAN arrow for more than four seconds. PRESET SCAN will appear on the display. You will hear a double beep. The radio will go to the ﬁrst preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station.
Page 241 AUTO EQ (Automatic Equalization): Press this button to select customized bass, midrange, and treble equalization settings designed for country, jazz, talk, pop, rock, and classical. To return to the manual mode (CUSTOM), press the AUTO EQ button until CUSTOM appears on the display. Then you will be able to manually adjust the bass, midrange, and treble using the AUDIO knob.
Page 242: Setting Preset Ptys (Rds Only)
To use the PTY interrupt feature, press and hold the P-TYPE button until you hear a beep on the PTY you want to interrupt with. When selected, an asterisk will appear beside that PTY on the display. You may select multiple interrupts if desired. When you are listening to a CD, the last selected RDS station will interrupt play if that selected program type format is broadcast.
Page 243 4. Press and hold one of the six numbered pushbuttons until you hear a beep. Whenever you press that numbered pushbutton, the PTY you set will return. 5. Repeat the steps for each pushbutton. RDS Messages ALERT!: Alert warns of local or national emergencies. When an alert announcement comes on the current radio station, ALERT! will appear on the display.
Page 244 If the brackets are on the display and TRAF is not, you can then press the TRAF button to remove the brackets or use the TUNE knob or the SEEK arrows to go to a station that supports traffic announcements. If no station is found, NO TRAFFIC will appear on the display.
Page 245 Radio Display Message Loading XM Acquiring channel audio (after 4 second delay) CH Off Air Channel not in service CH Unavail Channel no longer available No Info Artist Name/Feature not available No Info Song/Program Title not available No Info Category Name not available No Info No Text/Informational...
Page 246 Radio Display Message XM Locked Theft lock active Radio ID Radio ID label (channel 0) Unknown Radio ID not known (should only be if hardware failure) Chk XMRcvr Hardware failure 3-106 XM™ Radio Messages (cont’d) Condition The XM receiver in your vehicle may have previously been in another vehicle.
Page 247 Playing a CD The CD player can play the smaller 8 cm single CDs with an adapter ring. Full-size CDs and the smaller CDs are loaded in the same manner. If playing a CD-R the sound quality may be reduced due to CD-R quality, the method of recording, the quality of the music that has been recorded, and the way the CD-R has been handled.
Page 248: Playing A Speciﬁc Loaded Cd
To load more than one CD but less than six, complete Steps 1 through 3. When you have ﬁnished loading CDs, the radio will begin to play the last CD loaded. When a CD is inserted, the CD symbol will be displayed. If more than one CD has been loaded, a number for each CD will be displayed.
Page 249 RPT (Repeat): With repeat, you can repeat one track or an entire CD. To use repeat, do the following: • To repeat the track you are listening to, press and release the RPT button. RPT will appear on the display. Press RPT again to turn off repeat play. •...
Page 250: Using Song List Mode
RCL (Recall): Press this knob to see how long the current track has been playing. To change the default on the display (track and elapsed time), press the knob until you see the display you want, then hold the knob until the display ﬂashes. The selected display will now be the default.
Page 251 4. Press and hold the SONG LIST button for two seconds. When SONG LIST is pressed, a beep will be heard immediately. After two seconds of continuously pressing the SONG LIST button, two beeps will be heard to conﬁrm that the track has been deleted.
Page 252: Navigation/Radio System
Listening to a DVD Your vehicle may have a Rear Seat Entertainment System. If your vehicle has this system and a DVD is playing, the DVD symbol will appear on the radio display indicating that the DVD is available and can be listened through your vehicles speakers.
Page 253: Rear Seat Entertainment System
The navigation radio system includes digital sound processing (DSP), Radio Data System (RDS) with program “type” selections (PTY) that will seek out the kind of music you want to listen to, and XM™ Satellite Radio Service capabilities (48 contiguous US States). The radio system can also communicate with your navigation system to broadcast announcements on traffic, weather, and emergency alert...
Page 254: Stereo Rca Jacks
You can listen to the entertainment system through the wired headphone jacks on the RSA system (if equipped) when the following occurs: • The RSA system is on • A DVD or auxiliary device is playing • RSE is displayed on the front audio system by pressing the TAPE/CD button on the RSA system.
Page 255: Audio Speakers
Audio Speakers Audio from the DVD player or auxiliary devices can be heard through the following possible sources: • Wireless Headphones • Vehicle’s Speakers • Rear Seat Audio (RSA) Jacks (if equipped). Plug the wired headphones (not included) into the jacks on the RSA system.
Page 256: Dvd Player
Video Screen The video screen is located in the overhead console. To use the video screen, do the following: 1. Push forward on the release button and the screen will fold down. 2. Push the screen away from you and adjust its position as desired.
Page 257 DVD Player Buttons (Eject): Press this button to eject a DVD or CD. SRCE (Source): Press this button to toggle the system between the DVD player and an auxiliary source. (Main Menu): Press this button to view the media menu. The media menu is different on every DVD. Use the up, down, right, and left arrow buttons to move the cursor around the media menu.
Page 258: Playing A Disc
Parental Control Button: This button is located behind the video screen, next to the auxiliary jacks, near the driver of the vehicle. Press this button while a DVD or CD is playing to freeze the video and mute the audio. The video screen will display Parental Control On and the power indicator light on the DVD player will ﬂash.
Page 259: Ejecting A Disc
Ejecting a Disc Press the eject button on the DVD player faceplate to eject the disc. There is not an eject button on the remote control. If a disc is ejected from the player, but not removed, the DVD player will reload the disc after a short period of time.
Page 260: Remote Control Buttons
Remote Control Buttons (Power): Press this button to turn the DVD player on or off. (Title): Press this button to go back to the title screen, if there is one. (Directional Arrows): Press these buttons to move through DVD menus. The up arrow will skip to the next chapter or track, the down arrow will take you to the beginning of the current chapter or track.
Page 261 1 through 0 (Numeric Keypad): The numeric keypad provides you with the capability of direct chapter title and track number selection. 10 (Double Digit Entries): Press this button, located on the bottom right of the numeric key pad, to select chapter, title, and track numbers greater than 9.
Page 262: Setup Menu
Setup Menu To access the setup menu, ensure that a DVD is in the player and the video is stopped. Press the main menu button. Once the menu is activated, use the directional arrows and the enter button to navigate the screen. The setup menu allows the user to select default preferences for Menu Language, Subtitle Language, Audio Language, TV Aspect, TV Mode, and Dynamic...
Page 263: Tips And Trouble
Tips and Trouble Problem Recommended Action No power. The ignition may not be in run, accessory or RAP. The parental control button might have been pressed. (The power indicator light will ﬂash). Disc will not play. The system might be off. The parental control button might have been pressed.
Page 264 Problem Recommended Action The language in the audio Press the main menu or on the screen is wrong. button on the DVD player or the remote control and change the audio or language selection on the DVD menu. The remote control does Point the remote control not work.
Page 265 Problem Recommended Action The fast forward, reverse, Some commands that do previous and next one thing for DVDs will functions do not work. not always work or perform the same function for audio, CDs or games. These functions may also be disabled when the DVD is playing the copyright information or...
Page 266: Rear Seat Audio (Rsa)
Rear Seat Audio (RSA) This feature allows rear seat passengers to listen to and control any of the music sources: radio, cassette tapes, and CDs. However, the rear seat passengers can only control the music sources that the front seat passengers are not listening to.
Page 267: Rear Seat Audio (Rsa) Controls
Rear Seat Audio (RSA) Controls The following functions are controlled by the RSA system buttons: PWR (Power): Press this button to turn RSA on or off. VOL (Volume): Press this knob lightly so it extends. Turn the knob to increase or to decrease volume. Push the knob back into its stored position when you’re not using it.
Page 268: Theft-Deterrent Feature
P.SET PROG (Preset Program): The front passengers must be listening to something different for each of these functions to work: • Press this button to scan through the preset radio stations set on the pushbuttons on the main radio. The radio will go to a preset station stored on your pushbuttons, play for a few seconds, then go on to the next preset station.
Page 269: Audio Steering Wheel Controls
Audio Steering Wheel Controls If your vehicle has this feature, you can control certain radio functions using the buttons on your steering wheel. SOURCE: Press this button to play a cassette tape, CD, or a DVD (if equipped) when listening to the radio. If a cassette tape, and CD, and/or DVD are loaded, the system will go to the tape play ﬁrst.
Page 270: Understanding Radio Reception
Understanding Radio Reception The range for most AM stations is greater than for FM, especially at night. The longer range, however, can cause stations to interfere with each other. AM can pick up noise from things like storms and power lines. Try reducing the treble to reduce this noise.
Page 271: Care Of Your Cds And Dvds
The cut tape detection feature of your cassette tape player may identify the cleaning cassette tape as a damaged tape, in error. If the cleaning cassette ejects, insert the cassette at least three times to ensure thorough cleaning. You may also choose a non-scrubbing action, wet-type cleaner which uses a cassette with a fabric belt to clean the tape head.
Page 272: Integrated Windshield Antenna
Integrated Windshield Antenna The antenna in your vehicle is a very thin, metal layer in the windshield. If you look near the edges of the windshield, you can see the outline of the antenna. The connector is at the top of the windshield, where the headliner ends.
Page 273 Section 4 Your Driving, the Road, and Your Vehicle ...4-2 Driver Behavior ...4-2 Driving Environment ...4-2 Vehicle Design ...4-3 Defensive Driving ...4-3 Drunken Driving ...4-4 Control of a Vehicle ...4-7 Braking ...4-7 Traction Control System (TCS) ...4-11 All-Wheel Drive (AWD) System ...4-12 Steering ...4-13 Off-Road Recovery ...4-15 Passing ...4-15...
Page 274: Your Driving, The Road, And Your Vehicle
Your Driving, the Road, and Your Vehicle Whenever we drive, we are taking on an important responsibility. This is true for any motor vehicle — passenger car, van, truck, sport utility. Driver behavior, the driving environment, and the vehicle’s design all affect how well a vehicle performs. But statistics show that the most important factor, by far, is how we drive.
Page 275: Vehicle Design
Vehicle Design According to the U.S. Department of Transportation, utility vehicles have a signiﬁcantly higher rollover rate than other types of vehicles. Utility vehicles do have higher ground clearance and a narrower track or shorter wheelbase than passenger cars, to make them more capable for off-road driving.
Page 276: Drunken Driving
Drunken Driving Death and injury associated with drinking and driving is a national tragedy. It is the number one contributor to the highway death toll, claiming thousands of victims every year. Alcohol affects four things that anyone needs to drive a vehicle: •...
Page 277 According to the American Medical Association, a 180 lb (82 kg) person who drinks three 12 ounce (355 ml) bottles of beer in an hour will end up with a BAC of about 0.06 percent. The person would reach the same BAC by drinking three 4 ounce (120 ml) glasses of wine or three mixed drinks if each had 1-1/2 ounces (45 ml) of liquors like whiskey, gin or vodka.
Page 278 But the ability to drive is affected well below a BAC of 0.10 percent. Research shows that the driving skills of many people are impaired at a BAC approaching 0.05 percent, and that the effects are worse at night. All drivers are impaired at BAC levels above 0.05 percent.
Page 279: Control Of A Vehicle
Control of a Vehicle You have three systems that make your vehicle go where you want it to go. They are the brakes, the steering and the accelerator. All three systems have to do their work at the places where the tires meet the road. Sometimes, as when you are driving on snow or ice, it is easy to ask more of those control systems than the tires and road can provide.
Page 280: Anti-Lock Brake System (Abs)
Avoid needless heavy braking. Some people drive in spurts — heavy acceleration followed by heavy braking — rather than keeping pace with traffic. This is a mistake. Your brakes may not have time to cool between hard stops. Your brakes will wear out much faster if you do a lot of heavy braking.
Page 281 Let us say the road is wet and you are driving safely. Suddenly, an animal jumps out in front of you. You slam on the brakes and continue braking. Here is what happens with ABS: A computer senses that wheels are slowing down. If one of the wheels is about to stop rolling, the computer will separately work the brakes at each wheel.
Page 282: Braking In Emergencies
Remember: Anti-lock does not change the time you need to get your foot up to the brake pedal or always decrease stopping distance. If you get too close to the vehicle in front of you, you will not have time to apply your brakes if that vehicle suddenly slows or stops.
Page 283: Traction Control System (Tcs)
Traction Control System (TCS) Your vehicle may have a traction control system that limits wheel spin. This is especially useful in slippery road conditions. The system operates only if it senses that one or both of the front wheels are spinning or beginning to lose traction.
Page 284: All-Wheel Drive (Awd) System
To turn the system off, press the TRAC OFF button located on the instrument panel switchbank. If the system is limiting wheel spin when you press the button, the message will go off, but the system will not turn off until there is no longer a current need to limit wheel spin.
Page 285: Steering
Steering Power Steering If you lose power steering assist because the engine stops or the system is not functioning, you can steer but it will take much more effort. Steering Tips Driving on Curves It is important to take curves at a reasonable speed. A lot of the “driver lost control”...
Page 286: Steering In Emergencies
Steering in Emergencies There are times when steering can be more effective than braking. For example, you come over a hill and ﬁnd a truck stopped in your lane, or a car suddenly pulls out from nowhere, or a child darts out from between parked cars and stops right in front of you.
Page 287: Off-Road Recovery
Off-Road Recovery You may ﬁnd that your right wheels have dropped off the edge of a road onto the shoulder while you’re driving. If the level of the shoulder is only slightly below the pavement, recovery should be fairly easy. Ease off the accelerator and then, if there is nothing in the way, steer so that your vehicle straddles the edge of the pavement.
Page 288 • Do not get too close to the vehicle you want to pass while you are awaiting an opportunity. For one thing, following too closely reduces your area of vision, especially if you are following a larger vehicle. Also, you will not have adequate space if the vehicle ahead suddenly slows or stops.
Page 289: Loss Of Control
Loss of Control Let us review what driving experts say about what happens when the three control systems (brakes, steering and acceleration) do not have enough friction where the tires meet the road to do what the driver has asked. In any emergency, do not give up.
Page 290: Driving At Night
While driving on a surface with reduced traction, try your best to avoid sudden steering, acceleration or braking (including engine braking by shifting to a lower gear). Any sudden changes could cause the tires to slide. You may not realize the surface is slippery until your vehicle is skidding.
Page 291 Here are some tips on night driving. • Drive defensively. • Do not drink and drive. • Adjust your inside rearview mirror to reduce the glare from headlamps behind you. • Since you can not see as well, you may need to slow down and keep more space between you and other vehicles.
Page 292: Driving In Rain And On Wet Roads
Driving in Rain and on Wet Roads Rain and wet roads can mean driving trouble. On a wet road, you can not stop, accelerate or turn as well because your tire-to-road traction is not as good as on dry roads. And, if your tires do not have much tread left, you will get even less traction.
Page 293 Driving too fast through large water puddles or even going through some car washes can cause problems, too. The water may affect your brakes. Try to avoid puddles. But if you can not, try to slow down before you hit them. CAUTION: Wet brakes can cause accidents.
Page 294: Driving Through Deep Standing Water
Driving Through Deep Standing Water Notice: If you drive too quickly through deep puddles or standing water, water can come in through your engine’s air intake and badly damage your engine. Never drive through water that is slightly lower than the underbody of your vehicle. If you can not avoid deep puddles or standing water, drive through them very slowly.
Page 295: City Driving
City Driving One of the biggest problems with city streets is the amount of traffic on them. You will want to watch out for what the other drivers are doing and pay attention to traffic signals. Here are ways to increase your safety in city driving: •...
Page 296: Freeway Driving
Freeway Driving Mile for mile, freeways (also called thruways, parkways, expressways, turnpikes or superhighways) are the safest of all roads. But they have their own special rules. 4-24 The most important advice on freeway driving is: Keep up with traffic and keep to the right. Drive at the same speed most of the other drivers are driving.
Page 297: Before Leaving On A Long Trip
Once you are moving on the freeway, make certain you allow a reasonable following distance. Expect to move slightly slower at night. When you want to leave the freeway, move to the proper lane well in advance. If you miss your exit, do not, under any circumstances, stop and back up.
Page 298: Highway Hypnosis
Highway Hypnosis Is there actually such a condition as “highway hypnosis”? Or is it just plain falling asleep at the wheel? Call it highway hypnosis, lack of awareness, or whatever. There is something about an easy stretch of road with the same scenery, along with the hum of the tires on the road, the drone of the engine, and the rush of the wind against the vehicle that can make you sleepy.
Page 299 If you drive regularly in steep country, or if you are planning to visit there, here are some tips that can make your trips safer and more enjoyable. • Keep your vehicle in good shape. Check all ﬂuid levels and also the brakes, tires, cooling system and transaxle.
Page 300: Winter Driving
• You may see highway signs on mountains that warn of special problems. Examples are long grades, passing or no-passing zones, a falling rocks area or winding roads. Be alert to these and take appropriate action. Winter Driving 4-28 Here are some tips for winter driving: •...
Page 301: Driving On Snow Or Ice
Driving on Snow or Ice Most of the time, those places where your tires meet the road probably have good traction. However, if there is snow or ice between your tires and the road, you can have a very slippery situation. You’ll have a lot less traction or “grip”...
Page 302: If You're Caught In A Blizzard
Unless you have the anti-lock braking system, you’ll want to brake very gently, too. (If you do have anti-lock, see Braking on page 4-7. This system improves your vehicle’s stability when you make a hard stop on a slippery road.) Whether you have the anti-lock braking system or not, you’ll want to begin stopping sooner than you would on dry pavement.
Page 303 • Put on extra clothing or wrap a blanket around you. If you have no blankets or extra clothing, make body insulators from newspapers, burlap bags, rags, ﬂoor mats – anything you can wrap around yourself or tuck under your clothing to keep warm. You can run the engine to keep warm, but be careful.
Page 304: If You Are Stuck: In Sand, Mud, Ice Or Snow
Then, shut the engine off and close the window almost all the way to preserve the heat. Start the engine again and repeat this only when you feel really uncomfortable from the cold. But do it as little as possible. Preserve the fuel as long as you can. To help keep warm, you can get out of the vehicle and do some fairly vigorous exercises every half hour or so until help comes.
Page 305: Towing
Rocking Your Vehicle To Get It Out First, turn your steering wheel left and right. That will clear the area around your front wheels. If your vehicle has traction control, you should turn your traction control system off. See Traction Control System (TCS) on page 4-11.
Page 306: Recreational Vehicle Towing
Recreational Vehicle Towing Recreational vehicle towing means towing your vehicle behind another vehicle – such as behind a motorhome. The two most common types of recreational vehicle towing are known as “dinghy towing” (towing your vehicle with all four wheels on the ground) and “dolly towing” (towing your vehicle with two wheels on the ground and two wheels up on a device know as a “dolly”).
Page 307: Dolly Towing
Dolly Towing If you have a two-wheel-drive vehicle, it can be towed with two of its wheels on the ground. To dolly tow your vehicle, do the following: 1. Put the front wheels on a dolly. 2. Put the vehicle in PARK (P). 3.
Page 308: Loading Your Vehicle
Loading Your Vehicle It is very important to know how much weight your vehicle can carry. This weight is called the vehicle capacity weight and includes the weight of all occupants, cargo, and all nonfactory-installed options. Two labels on your vehicle show how much weight it may properly carry, the Tire and Loading Information label and the Certiﬁcation/Tire label.
Page 309 If your vehicle does not have the Tire and Loading Information label, the Certiﬁcation/Tire label shows the tire size and recommended inﬂation pressures needed to obtain the Gross Vehicle Weight Rating (GVWR) and the Gross Axle Weight Rating (GAWR) for the front and rear axles.
Page 310 Example 1 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 1 Subtract Occupant Weight 150 lbs (68 kg) Available Occupant and Cargo Weight 4-38 Total Item 1,000 lbs (453 kg) 300 lbs (136 kg) 700 lbs. (317 kg) Example 2 Loading Your Vehicle Description...
Page 311 Example 3 Loading Your Vehicle Item Description Vehicle Capacity Weight for Example 3 Subtract Occupant Weight 200 lbs (91 kg) Available Cargo Weight Refer to your vehicle’s tire and loading information label for speciﬁc information about your vehicle’s capacity weight and seating positions. The combined weight of the driver, passengers, and cargo should never exceed your vehicle’s capacity weight.
Page 312 Certiﬁcation/Tire Label The Certiﬁcation/Tire Label is found on the rear edge of the driver’s door. 4-40 The label shows the size of your original tires and the inﬂation pressures needed to obtain the gross weight capacity of your vehicle. This is called the Gross Vehicle Weight Rating (GVWR).
Page 313 Never exceed the GVWR for your vehicle or the GAWR for either the front or rear axle. CAUTION: Do not load your vehicle any heavier than the GVWR, or either the maximum front or rear GAWR. If you do, parts on your vehicle can break, and it can change the way your vehicle handles.
Page 314: Towing A Trailer
Automatic Level Control On vehicles equipped with automatic level control, the rear of the vehicle is automatically kept level as you load or unload your vehicle. However, you should still not exceed the GVWR or the GAWR. See Loading Your Vehicle on page 4-36. You may hear the compressor operating when you load or unload your vehicle, and periodically as the system self-adjusts.
Page 315: If You Do Decide To Pull A Trailer
Your vehicle can tow a trailer. To identify what the vehicle trailering capacity is for your vehicle, you should read the information in “Weight of the Trailer” that appears later in this section. But trailering is different than just driving your vehicle by itself. Trailering means changes in handling, acceleration, braking, durability, and fuel economy.
Page 316 4-44 You can ask your dealer for our trailering information or advice, or you can write us at: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, write to:...
Page 317: Weight Of The Trailer Tongue
Weight of the Trailer Tongue The tongue load (A) of any trailer is an important weight to measure because it affects the total or gross weight of your vehicle. The Gross Vehicle Weight (GVW) includes the curb weight of the vehicle, any cargo you may carry in it, and the people who will be riding in the vehicle.
Page 318: Total Weight On Your Vehicle's Tires
Total Weight on Your Vehicle’s Tires Be sure your vehicle’s tires are inﬂated to the upper limit for cold tires. You will ﬁnd these numbers on the Certiﬁcation/Tire Label at the rear edge of the driver’s door, or see Loading Your Vehicle on page 4-36. Do not go over the GVW limit for your vehicle, including the weight of the trailer tongue.
Page 319: Driving With A Trailer
Driving with a Trailer CAUTION: If you have a rear-most window open and you pull a trailer with your vehicle, carbon monoxide (CO) could come into your vehicle. You can’t see or smell CO. It can cause unconsciousness or death. See “Engine Exhaust”...
Page 320: Following Distance
Following Distance Stay at least twice as far behind the vehicle ahead as you would when driving your vehicle without a trailer. This can help you avoid situations that require heavy braking and sudden turns. Passing You will need more passing distance up ahead when you are towing a trailer.
Page 321: Driving On Grades
Driving On Grades Reduce speed and shift to a lower gear before you start down a long or steep downgrade. If you do not shift down, you might have to use your brakes so much that they would get hot and no longer work well. If you are towing a trailer that weighs more than 1,000 lbs.
Page 322: Trailer Wiring Harness
Maintenance When Trailer Towing Your vehicle will need service more often when you are pulling a trailer. See the Maintenance Schedule for more on this. Things that are especially important in trailer operation are automatic transaxle ﬂuid, engine oil, belts, cooling system and brake system.
Page 323 Section 5 Service ...5-3 Doing Your Own Service Work ...5-3 Adding Equipment to the Outside of Your Vehicle ...5-4 Fuel ...5-4 Gasoline Octane ...5-4 Gasoline Speciﬁcations ...5-5 California Fuel ...5-5 Additives ...5-6 Fuels in Foreign Countries ...5-6 Filling Your Tank ...5-7 Filling a Portable Fuel Container ...5-9 Checking Things Under the Hood ...5-10 Hood Release ...5-11...
Page 324 Section 5 If a Tire Goes Flat ...5-76 Changing a Flat Tire ...5-77 Compact Spare Tire ...5-98 Appearance Care ...5-99 Cleaning the Inside of Your Vehicle ...5-99 Care of Safety Belts ...5-102 Weatherstrips ...5-102 Cleaning the Outside of Your Vehicle ...5-103 Sheet Metal Damage ...5-105 Finish Damage ...5-105 Underbody Maintenance ...5-105...
Page 325: Service
Service Your dealer knows your vehicle best and wants you to be happy with it. We hope you will go to your dealer for all your service needs. You will get genuine GM parts and GM-trained and supported service people. We hope you will want to keep your GM vehicle all GM.
Page 326: Adding Equipment To The Outside Of Your Vehicle
CAUTION: (Continued) • Be sure to use the proper nuts, bolts and other fasteners. “English” and “metric” fasteners can be easily confused. If you use the wrong fasteners, parts can later break or fall off. You could be hurt. Adding Equipment to the Outside of Your Vehicle Things you might add to the outside of your vehicle can affect the airﬂow around it.
Page 327: Gasoline Speciﬁcations
Gasoline Speciﬁcations It is recommended that gasoline meet speciﬁcations which were developed by automobile manufacturers around the world and contained in the World-Wide Fuel Charter which is available from the Alliance of Automobile Manufacturers at www.autoalliance.org. Gasoline meeting these speciﬁcations could provide improved driveability and emission control system performance compared to other gasoline.
Page 328: Additives
Additives To provide cleaner air, all gasolines in the United States are now required to contain additives that will help prevent engine and fuel system deposits from forming, allowing your emission control system to work properly. You should not have to add anything to your fuel.
Page 329: Filling Your Tank
Filling Your Tank CAUTION: Fuel vapor burns violently and a fuel ﬁre can cause bad injuries. To help avoid injuries to you and others, read and follow all the instructions on the pump island. Turn off your engine when you are refueling. Do not smoke if you are near fuel or refueling your vehicle.
Page 330 While refueling, hang the fuel cap inside the fuel door by placing the fuel cap tether in the hanger. To remove the fuel cap, turn it slowly to the left (counterclockwise). The fuel cap has spring in it; if you let go of the cap too soon, it will spring back to the right.
Page 331: Filling A Portable Fuel Container
CAUTION: If a ﬁre starts while you are refueling, do not remove the nozzle. Shut off the ﬂow of fuel by shutting off the pump or by notifying the station attendant. Leave the area immediately. The malfunction indicator lamp (SERVICE ENGINE SOON or CHECK ENGINE light) will come on if the fuel cap is not properly installed.
Page 332: Checking Things Under The Hood
Checking Things Under the Hood CAUTION: An electric fan under the hood can start up and injure you even when the engine is not running. Keep hands, clothing and tools away from any underhood electric fan. 5-10 CAUTION: Things that burn can get on hot engine parts and start a ﬁre.
Page 333: Hood Release
Hood Release To open the hood, do the following: 1. Pull the hood release handle, located under the instrument panel on the driver’s side of the vehicle. 2. At the front of the vehicle, pull up on the center of the hood, and push the secondary hood release to the right.
Page 334: Engine Compartment Overview
Engine Compartment Overview When you lift the hood, you’ll see these items: 5-12...
Page 335 A. Underhood Fuse Block. See Fuses and Circuit Breakers on page 5-109. B. Remote Positive (+) Terminal. See Jump Starting on page 5-43. C. Power Steering Fluid Reservoir. See Power Steering Fluid on page 5-36. D. Automatic Transaxle Fluid Dipstick. See Automatic Transaxle Fluid on page 5-21.
Page 336: Engine Oil
Engine Oil Checking Engine Oil It is a good idea to check your engine oil every time you get fuel. In order to get an accurate reading, the oil must be warm and the vehicle must be on level ground. The engine oil dipstick handle is a yellow loop.
Page 337: When To Add Engine Oil
When to Add Engine Oil If the oil is at or below the cross-hatched area at the tip of the dipstick, then you will need to add at least one quart of oil. But you must use the right kind. This section explains what kind of oil to use.
Page 338: What Kind Of Engine Oil To Use
What Kind of Engine Oil to Use Look for two things: • GM6094M Your vehicle’s engine requires oil meeting GM Standard GM6094M. You should look for and use only an oil that meets GM Standard GM6094M. • SAE 5W-30 As shown in the viscosity chart, SAE 5W-30 is best for your vehicle.
Page 339: Engine Oil Additives
Oils meeting these requirements should also have the starburst symbol on the container. This symbol indicates that the oil has been certiﬁed by the American Petroleum Institute (API). You should look for this information on the oil container, and use only those oils that are identiﬁed as meeting GM Standard GM6094M and have the starburst symbol on the front of the oil container.
Page 340: When To Change Engine Oil
When to Change Engine Oil (GM Oil Life System) Your vehicle has a computer system that lets you know when to change the engine oil and ﬁlter. This is based on engine revolutions and engine temperature, and not on mileage. Based on driving conditions, the mileage at which an oil change will be indicated can vary considerably.
Page 341: Engine Air Cleaner/Filter
If your vehicle has the optional DIC, do the following: 1. Turn the ignition to ON, with the engine off. 2. Press the MODE button until the DIC reads OIL LIFE LEFT/HOLD SET TO RESET. 3. Press and hold the SET button until 100% is displayed.
Page 342: How To Inspect The Engine Air Cleaner/Filter
How to Inspect the Engine Air Cleaner/Filter To inspect the air cleaner/ﬁlter, remove the ﬁlter from the vehicle and lightly shake the ﬁlter to release loose dust and dirt. If the ﬁlter remains caked with dirt, a new ﬁlter is required. To inspect or replace the air cleaner/ﬁlter, do the following: 1.
Page 343: Automatic Transaxle Fluid
Automatic Transaxle Fluid When to Check and Change Automatic Transaxle Fluid A good time to check your automatic transaxle ﬂuid level is when the engine oil is changed. Change both the ﬂuid and ﬁlter every 50,000 miles (83 000 km) if the vehicle is mainly driven under one or more of these conditions: •...
Page 344 Checking the Fluid Level To prepare your vehicle, do the following: 1. Park your vehicle on a level place and keep the engine running. 2. With the parking brake applied, place the shift lever in PARK (P). 3. With your foot on the brake pedal, move the shift lever through each gear range, pausing for about three seconds in each range.
Page 345: Engine Coolant
How to Add Automatic Transaxle Fluid Refer to the Maintenance Schedule to determine what kind of transaxle ﬂuid to use. See Recommended Fluids and Lubricants on page 6-12. If the ﬂuid level is low, add only enough of the proper ﬂuid to bring the level into the cross-hatched area on the dipstick.
Page 346: What Coolant To Use
What Coolant to Use Use a mixture of one-half clean, drinkable water and ® one-half DEX-COOL coolant which won’t damage aluminum parts. If you use this coolant mixture, you don’t need to add anything else. CAUTION: Adding only plain water to your cooling system can be dangerous.
Page 347: Radiator Pressure Cap
The vehicle must be on a level surface. When your engine is cold, the coolant level should be at the FULL COLD mark, or a little higher. When your engine is warm, the level should be above the FULL COLD mark or a little higher.
Page 348: Engine Overheating
Engine Overheating You will ﬁnd an engine coolant temperature gage on your vehicle’s instrument panel. See Engine Coolant Temperature Gage on page 3-46. You also have an engine coolant temperature warning message on your instrument panel. See Engine Coolant Temperature Warning Message on page 3-51.
Page 349: If Steam Is Coming From Your Engine
If Steam Is Coming From Your Engine CAUTION: Steam from an overheated engine can burn you badly, even if you just open the hood. Stay away from the engine if you see or hear steam coming from it. Just turn it off and get everyone away from the vehicle until it cools down.
Page 350: If No Steam Is Coming From Your Engine
If No Steam Is Coming From Your Engine If you get an engine overheat warning but see or hear no steam, the problem may not be too serious. Sometimes the engine can get a little too hot when you: • Climb a long hill on a hot day •...
Page 351: Cooling System
Cooling System When you decide it is safe to lift the hood, here’s what you will see: A. Radiator Pressure Cap B. Electric Engine Cooling Fans C. Coolant Recovery Tank CAUTION: An electric engine cooling fan under the hood can start up even when the engine is not running and can injure you.
Page 352 The coolant level should be at or above the full cold mark. If it is not, you may have a leak at the pressure cap or in the radiator hoses, heater hoses, radiator, water pump or somewhere else in the cooling system. CAUTION: Heater and radiator hoses, and other engine parts, can be very hot.
Page 353 How to Add Coolant to the Coolant Recovery Tank If you have not found a problem yet, but the coolant level is not at or above the full cold mark, add a 50/50 mixture of clean, drinkable water and DEX-COOL engine coolant at the coolant recovery tank.
Page 354 When the coolant in the coolant recovery tank is at or above the full cold mark, start your vehicle. If the overheat warning continues, there is one more thing you can try. You can add the proper coolant mixture directly to the radiator, but be sure the cooling system is cool before you do it.
Page 355: How To Add Coolant To The Radiator
How to Add Coolant to the Radiator Notice: Your engine has a speciﬁc radiator ﬁll procedure. Failure to follow this procedure could cause your engine to overheat and be severely damaged. 1. You can remove the radiator pressure cap when the cooling system, including the radiator pressure cap and upper radiator hose, is no longer hot.
Page 356 Housing 3. After the engine cools, open the coolant air bleed valves. There are two bleed valves. One is located on the thermostat housing. The other is located on the thermostat bypass tube. 5-34 Bypass Tube 4. Fill the radiator with the proper DEX-COOL coolant mixture, up to the base of the ﬁller neck.
Page 357 6. Start the engine and let it run until you can feel the upper radiator hose getting hot. Watch out for the engine cooling fans. 7. By this time, the coolant level inside the radiator ﬁller neck may be lower. If the level is lower, add more of the proper DEX-COOL through the ﬁller neck until the level reaches the base of the ﬁller neck.
Page 358: Power Steering Fluid
9. Then ﬁll the coolant recovery tank to the FULL COLD mark. 10. Put the cap back on the coolant recovery tank. 5-36 Power Steering Fluid The power steering ﬂuid reservoir is located to the right of the windshield washer ﬂuid reservoir, at the back of the engine compartment.
Page 359: What Power Steering Fluid To Use
When to Check Power Steering Fluid It is not necessary to regularly check power steering ﬂuid unless you suspect there is a leak in the system or you hear an unusual noise. A ﬂuid loss in this system could indicate a problem. Have the system inspected and repaired.
Page 360: Brakes
Adding Washer Fluid Open the cap with the washer symbol on it. Add washer ﬂuid until the tank is full. Notice: • When using concentrated washer ﬂuid, follow the manufacturer’s instructions for adding water. • Don’t mix water with ready-to-use washer ﬂuid. Water can cause the solution to freeze and damage your washer ﬂuid tank and other parts of the washer system.
Page 361 Your brake master cylinder reservoir is ﬁlled with DOT-3 brake ﬂuid. See Engine Compartment Overview on page 5-12 for the location of the reservoir. There are only two reasons why the brake ﬂuid level in the reservoir might go down. The ﬁrst is that the brake ﬂuid goes down to an acceptable level during normal brake lining wear.
Page 362 What to Add When you do need brake ﬂuid, use only DOT-3 brake ﬂuid. Use new brake ﬂuid from a sealed container only. See Recommended Fluids and Lubricants on page 6-12. Always clean the brake ﬂuid reservoir cap and the area around the cap before removing it.
Page 363: Brake Wear
Brake Wear Your vehicle has four-wheel disc brakes. Disc brake pads have built-in wear indicators that make a high-pitched warning sound when the brake pads are worn and new pads are needed. The sound may come and go or be heard all the time your vehicle is moving (except when you are pushing on the brake pedal ﬁrmly).
Page 364: Battery
Replacing Brake System Parts The braking system on a vehicle is complex. Its many parts have to be of top quality and work well together if the vehicle is to have really good braking. Your vehicle was designed and tested with top-quality GM brake parts.
Page 365: Jump Starting
Jump Starting If your battery has run down, you may want to use another vehicle and some jumper cables to start your vehicle. Be sure to follow the steps below to do it safely. CAUTION: Batteries can hurt you. They can be dangerous because: •...
Page 366 4. Open the hoods and locate the batteries. Find the positive (+) and negative ( ) terminals on each vehicle. You will not need to access your battery for jump starting. Your vehicle has a remote positive (+) jump starting terminal for that purpose. The terminal is located under a tethered cap at the front of the underhood fuse and relay center.
Page 367 CAUTION: Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running. 5. Check that the jumper cables don’t have loose or missing insulation. If they do, you could get a shock.
Page 368 8. Now connect the black negative ( ) cable to the negative ( ) terminal of the good battery. Use a remote negative ( ) terminal if the vehicle has one. 5-46 Don’t let the other end touch anything until the next step.
Page 369 Notice: If the jumper cables are removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by your warranty. Remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.
Page 370: All-Wheel Drive
All-Wheel Drive If you have an all-wheel-drive vehicle, be sure to perform the lubricant checks described in this section. However, they have two additional systems that need lubrication. Transfer Case (Power Transfer Unit) When to Check Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant.
Page 371 Carrier Assembly-Differential (Rear Drive Module) When to Check and Change Lubricant Refer to the Maintenance Schedule to determine how often to check the lubricant and when to change it. See Scheduled Maintenance on page 6-4. How to Check Lubricant To get an accurate reading, the vehicle should be on a level surface.
Page 372: Bulb Replacement
Bulb Replacement For the type of bulbs, see Replacement Bulbs on page 5-54. For any bulb changing procedure not listed in this section, contact your dealer. Halogen Bulbs CAUTION: Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured.
Page 373 6. Turn the bulb socket 7. Pull the bulb assembly out from the lamp housing. one-quarter of a turn clockwise. 8. Unhook the electrical connector by lifting up the 9. Install the new bulb into the electrical connector. gray tabs and separate the connector from the bulb base.
Page 374: Front Turn Signal, Sidemarker And Parking
10. Put the bulb assembly back into the lamp housing and turn the bulb socket one-quarter of a turn counterclockwise. 11. Align the retaining clips on the back of the headlamp with the rectangular holes in the mounting panel. 12. Push ﬁrmly on both ends of the headlamp to snap it into position.
Page 375: Taillamps And Back-Up Lamps
7. Install the new bulb into the electrical connector. Push the bulb ﬁrmly enough so that the tabs hook over the tab on the bulb. 8. Put the bulb assembly back into the lamp housing and turn the bulb socket one-quarter of a turn clockwise.
Page 376: Replacement Bulbs
A. Outboard Taillamp B. Center Taillamp C. Inboard Back-Up Lamp 6. Turn the bulb socket one-quarter of a turn counterclockwise. 7. Pull the bulb assembly out from the lamp housing. 8. Pull the bulb out of the base. 9. Install the new bulb into the electrical connector. Push the bulb ﬁrmly enough so that the tabs hook over the tab on the bulb.
Page 377: Windshield Wiper Blade Replacement
Windshield Wiper Blade Replacement Windshield wiper blades should be inspected at least twice a year for wear or cracking. See “Wiper Blade Check” under Owner Checks and Services on page 6-8 for more information. Replacement blades come in different types and are removed in different ways.
Page 378 5. Push the new wiper blade securely on the wiper arm until you hear the release clip “click” into place. 6. Push the release clip, from Step 4, down to secure the wiper blade into place. To replace the backglass mounted wiper blade, do the following: 1.
Page 379: Tires
Tires Your new vehicle comes with high-quality tires made by a leading tire manufacturer. If you ever have questions about your tire warranty and where to obtain service, see your GM Warranty booklet for details. For additional information refer to the tire manufacturer’s booklet included with your vehicle’s Owner’s Manual.
Page 380: Tire Sidewall Labeling
Tire Sidewall Labeling Useful information about a tire is molded into it’s sidewall. The examples below show a typical passenger car tire and a compact spare tire sidewall. Passenger Car Tire Example 5-58...
Page 381 (A) Tire Size: The tire size code is a combination of letters and numbers used to deﬁne a particular tire’s width, height, aspect ratio, construction type and service description. See the “Tire Size” illustration later in this section for more detail. (B) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 382 (A) Temporary Use Only: The compact spare tire or temporary use tire has a tread life of approximately 3,000 miles (5 000 km) and should not be driven at speeds over 65 mph (105 km/h). The compact spare tire is for emergency use when a regular road tire has lost air and gone ﬂat.
Page 383: Tire Size
(F) Tire Size: A combination of letters and numbers deﬁne a tire’s width, height, aspect ratio, construction type and service description. The letter “T” as the ﬁrst character in the tire size means the tire is for temporary use only. (G) Tire Performance Criteria Speciﬁcation (TPC Spec): Original equipment tires designed to GM’s speciﬁc tire performance criteria have a TPC...
Page 384: Tire Terminology And Deﬁnitions
Tire Terminology and Deﬁnitions Air Pressure: The amount of air inside the tire pressing outward on each square inch of the tire. Air pressure is expressed in pounds per square inch (psi) or kilopascal (kPa). Accessory Weight: This means the combined weight of optional accessories.
Page 385 Load Index: An assigned number ranging from 1 to 279 that corresponds to the load carrying capacity of a tire. Maximum Inﬂation Pressure: The maximum air pressure to which a cold tire may be inﬂated. The maximum air pressure is molded onto the sidewall. Maximum Load Rating: The load rating for a tire at the maximum permissible inﬂation pressure for that tire.
Page 386: Inﬂation - Tire Pressure
UTQGS: Uniform Tire Quality Grading Standards, a tire information system that provides consumers with ratings for a tire’s traction, temperature and treadwear. Ratings are determined by tire manufacturers using government testing procedures. The ratings are molded into the sidewall of the tire. See Uniform Tire Quality Grading on page 5-71.
Page 387: Check Tire Pressure System
When to Check Check your tires once a month or more. Don’t forget your compact spare tire. It should be at 60 psi (420 kPa). How to Check Use a good quality pocket-type gage to check tire pressure. You can’t tell if your tires are properly inﬂated simply by looking at them.
Page 388 If the anti-lock brake system warning light comes on, the check tire pressure system may not be working properly. See your dealer for service. Also, see Anti-Lock Brake System Warning Light on page 3-45. The check tire pressure system detects differences in tire rotation speeds that are caused by changes in tire pressure.
Page 389: Tire Inspection And Rotation
You will hear three chimes, then the LOW TIRE PRESSURE message will go off and the DIC will return to TIRE PRESSURE NORMAL. If the LOW TIRE PRESSURE message comes back on, the check tire pressure system has not reset. Repeat the procedure. The system completes the calibration process during driving.
Page 390 When rotating your tires, always use the correct rotation pattern shown here. Don’t include the compact spare tire in your tire rotation. After the tires have been rotated, adjust the front and rear inﬂation pressures as shown on the Certiﬁcation/Tire label or the Tire and Loading Information label.
Page 391: When It Is Time For New Tires
When It Is Time for New Tires One way to tell when it’s time for new tires is to check the treadwear indicators, which will appear when your tires have only 1/16 inch (1.6 mm) or less of tread remaining. You need a new tire if any of the following statements are true: •...
Page 392: Buying New Tires
Buying New Tires To ﬁnd out what kind and size of tires you need, look at the tire and loading information label. For an example of this label and its location, see Loading Your Vehicle on page 4-36. The tires installed on your vehicle when it was new had a Tire Performance Criteria Speciﬁcation (TPC Spec) number on each tire’s sidewall.
Page 393: Uniform Tire Quality Grading
Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration, which grades tires by treadwear, traction and temperature performance.
Page 394: Wheel Alignment And Tire Balance
Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speciﬁed indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
Page 395: Used Replacement Wheels
CAUTION: Using the wrong replacement wheels, wheel bolts or wheel nuts on your vehicle can be dangerous. It could affect the braking and handling of your vehicle, make your tires lose air and make you lose control. You could have a collision in which you or others could be injured.
Page 396: Tire Chains
Tire Chains CAUTION: Don’t use tire chains. There’s not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension or other vehicle parts. The area damaged by the tire chains could cause you to lose control of your vehicle and you or others may be injured in a crash.
Page 397 CAUTION: Inﬂating something too much can make it explode, and you or others could be injured. Be sure to read the inﬂator instructions, and inﬂate any object only to its recommended pressure. To use your accessory inﬂator system, do the following: 1.
Page 398: If A Tire Goes Flat
If a Tire Goes Flat It’s unusual for a tire to “blowout” while you’re driving, especially if you maintain your tires properly. If air goes out of a tire, it’s much more likely to leak out slowly. But if you should ever have a “blowout,” here are a few tips about what to expect and what to do: If a front tire fails, the ﬂat tire will create a drag that pulls the vehicle toward that side.
Page 399: Changing A Flat Tire
Changing a Flat Tire If a tire goes ﬂat, avoid further tire and wheel damage by driving slowly to a level place. Turn on your hazard warning ﬂashers. CAUTION: Changing a tire can cause an injury. The vehicle can slip off the jack and roll over you or other people.
Page 400: Removing The Spare Tire And Tools
Removing the Spare Tire and Tools The equipment you will need is located in the storage compartment on the passenger’s side, at the rear of the vehicle. 1. Open the jack storage compartment by lifting up the tab and pulling the cover off. A.
Page 401 Removing the Spare Tire (Vehicles without the Rear Convenience Center) The compact spare tire is located under the vehicle, behind the rear bumper. Use the spare tire hoist to raise, lower and store the compact spare tire. See Compact Spare Tire on page 5-98 for more information about the compact spare.
Page 402 5. After removing the spare tire, turn the wrench clockwise to raise the cable back up. Do not store a full-size or a ﬂat road tire under the vehicle. See “Storing a Flat or Spare Tire and Tools” later in this section. To continue changing the ﬂat tire see “Removing the Flat Tire and Installing the Spare Tire”...
Page 403 Removing the Spare Tire (Vehicles with the Rear Convenience Center) The compact spare tire is located under the vehicle, ahead of the rear bumper. See Compact Spare Tire on page 5-98 for more information about the compact spare. A. Rear Convenience Center B.
Page 404 3. Attach the folding wrench into the hoist shaft. 4. Turn the folding wrench counterclockwise to lower the spare tire to the ground. Continue turning the wrench until the spare tire can be pulled out from under the vehicle. 5. To remove the spare tire from the cable, tilt the retainer and slip it through the wheel opening.
Page 405 If the spare tire will not lower, the secondary latch may be engaged causing the tire not to lower. Do the following to check the cable: 1. Check under the vehicle to see if the cable is visible. 2. If it is not visible, see “Secondary Latch System” following.
Page 406: Secondary Latch System
Secondary Latch System Your vehicle has an underbody mounted tire hoist assembly equipped with a secondary latch system. It is designed to stop the compact spare tire from suddenly falling off your vehicle if the cable holding the spare tire is damaged. For the secondary latch to work, the tire must be stowed with the valve stem pointing down.
Page 407 1. If the cable is not visible, start this procedure at Step 3. 2. Turn the wrench counterclockwise until approximately 6 inches (15 cm) of cable is exposed. 3. Attach the folding wrench to the jack and raise the jack at least 10 turns. 4.
Page 408 7. Lower the jack by turning the folding wrench counterclockwise. Keep lowering the jack until the spare tire is resting on the folding wrench. 5-86 8. Grasp the spare tire with both hands and pull it out from under the vehicle. 9.
Page 409: Removing The Flat Tire And Installing The Spare Tire
Removing the Flat Tire and Installing the Spare Tire 1. If there is a wheel cover, loosen the plastic nut caps with the wheel wrench. They will not come off. Then, using the ﬂat end of the wheel wrench, pry along the edge of the cover until it comes off. Be careful;...
Page 410 3. Near each wheel, there is a notch in the vehicle’s body. Position the jack and raise the jack head until it ﬁts ﬁrmly into the notch in the vehicle’s frame nearest the ﬂat tire. Notice: If you use a jack to raise the vehicle without positioning it correctly, you could damage your vehicle.
Page 411 4. Attach the folding wrench to the jack, and turn the wrench clockwise to raise the jack head 3 inches (7.6 cm). 5. Raise the vehicle by turning the folding wrench clockwise in the jack. Raise the vehicle far enough off the ground so that there is enough room for the spare tire to ﬁt under the wheel well.
Page 412 8. Install the spare tire and put the wheel nuts back on with the rounded end of the nuts toward the wheel. Tighten each nut by hand until the wheel is held against the hub. 9. Lower the vehicle by attaching the folding wrench to the jack and turning the wrench counterclockwise.
Page 413: Storing A Flat Or Spare Tire And Tools
Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the proper torque speciﬁcation. 11. Do not try to put a wheel cover on the compact spare tire.
Page 414: Storing The Spare Tire And Tools
Storing the Spare Tire and Tools 1. Lay the compact spare tire on the ground at the rear of the vehicle. Position the compact spare tire so that the valve stem is pointed down facing the rear of the vehicle. 2.
Page 415 A. Push and Pull B. Turn Tire 9. Make sure the tire is stored securely. Push, pull, and then try to turn the tire. If the tire moves, use the folding wrench to tighten the cable. Put back all tools as they were stored in the jack storage compartment and put the compartment cover back on.
Page 416: Convenience Center
Storing the Flat Tire (Vehicles without the Stowable Seat and without the Rear Convenience Center) A. D-Ring B. Wing Nut C. J-Hook D. Valve Stem E. Full-Size Tire 5-94 1. Flip up the D-ring located in the rear cargo area. 2.
Page 417 Storing the Flat Tire (Vehicles with the Rear Convenience Center) A. D-Ring B. Rear Convenience Center C. Wing Nut D. J-Hook E. Full-Size Tire F. Cap on Bottom of Storage Compartment 1. Open the center storage compartment door of the rear convenience center.
Page 418 Storing the Flat Tire (Vehicles with the Stowable Seat) A. Rear Convenience Center B. Full-Size Tire C. D-Ring D. Stowable Seat Strap E. Cargo Net Hook F. J-Hook G. Wing Nut 5-96 1. If the seatback is not in an upright position, move it to an upright position.
Page 419 Storing the Flat Tire with the Stowable Seatback Folded Flat A. Stowable Seat B. Full-Size Tire C. Wing Nut D. J-Hook E. D-Ring 1. Fold the seatback down and ﬂip the D-ring up. 2. Lay the tire on the seatback with the valve stem pointing up with the center hole of the tire over the D-ring.
Page 420: Compact Spare Tire
Compact Spare Tire Although the compact spare tire was fully inﬂated when your vehicle was new, it can lose air after a time. Check the inﬂation pressure regularly. It should be 60 psi (420 kPa). After installing the compact spare on your vehicle, you should stop as soon as possible and make sure your spare tire is correctly inﬂated.
Page 421: Appearance Care
Appearance Care Remember, cleaning products can be hazardous. Some are toxic. Others can burst into ﬂames if you strike a match or get them on a hot part of the vehicle. Some are dangerous if you breathe their fumes in a closed space.
Page 422: Cleaning Fabric/Carpet
Cleaning Fabric/Carpet Your dealer has cleaners for the cleaning of fabric and carpet. They will clean normal spots and stains very well. You can get GM-approved cleaning products from your dealer. See Vehicle Care/Appearance Materials on page 5-106. Here are some cleaning tips: •...
Page 423: Special Fabric Cleaning Problems
Special Fabric Cleaning Problems Stains caused by such things as catsup, coffee (black), egg, fruit, fruit juice, milk, soft drinks, vomit, urine and blood can be removed as follows: 1. Carefully scrape off excess stain, then sponge the soiled area with cool water. 2.
Page 424: Cleaning The Top Of The Instrument Panel
Cleaning the Top of the Instrument Panel Use only mild soap and water to clean the top surfaces of the instrument panel. Sprays containing silicones or waxes may cause annoying reﬂections in the windshield and even make it difficult to see through the windshield under certain conditions.
Page 425: Cleaning The Outside Of Your Vehicle
Cleaning the Outside of Your Vehicle The paint ﬁnish on your vehicle provides beauty, depth of color, gloss retention and durability. Washing Your Vehicle The best way to preserve your vehicle’s ﬁnish is to keep it clean by washing it often with lukewarm or cold water. Don’t wash your vehicle in the direct rays of the sun.
Page 426: Cleaning Aluminum Or Chrome-Plated Wheels
Foreign materials such as calcium chloride and other salts, ice melting agents, road oil and tar, tree sap, bird droppings, chemicals from industrial chimneys, etc., can damage your vehicle’s ﬁnish if they remain on painted surfaces. Wash the vehicle as soon as possible.
Page 427: Sheet Metal Damage
Use chrome polish only on chrome-plated wheels, but avoid any painted surface of the wheel, and buff off immediately after application. Don’t take your vehicle through an automatic car wash that has silicone carbide tire cleaning brushes. These brushes can also damage the surface of these wheels. Cleaning Tires To clean your tires, use a stiff brush with tire cleaner.
Page 428: Chemical Paint Spotting
Chemical Paint Spotting Some weather and atmospheric conditions can create a chemical fallout. Airborne pollutants can fall upon and attack painted surfaces on your vehicle. This damage can take two forms: blotchy, ring-shaped discolorations, and small, irregular dark spots etched into the paint surface.
Page 429: Vehicle Identiﬁcation
Description Cleans, shines and Foaming Tire Shine Low protects in one easy step, Gloss no wiping necessary. Medium foaming shampoo. Cleans and Wash Wax Concentrate lightly waxes. Biodegradable and phosphate free. Quickly and easily removes spots and stains Spot Lifter from carpets, vinyl and cloth upholstery.
Page 430: Service Parts Identiﬁcation Label
Service Parts Identiﬁcation Label You will ﬁnd this label on the inside of the access panel located on the driver’s side of the rear of the vehicle. It is very helpful if you ever need to order parts. On this label, you will ﬁnd the following: •...
Page 431: Windshield Wiper Fuses
Windshield Wiper Fuses The windshield wiper motor is protected by an internal circuit breaker and a fuse. If the motor overheats due to heavy snow, etc., the wiper will stop until the motor cools. If the overload is caused by some electrical problem, be sure to get it ﬁxed.
Page 432: Floor Console Fuse Block
Floor Console Fuse Block The ﬂoor console fuse block is located to the left of the glove box near the ﬂoor. Pull the door open to access the fuse block. 5-110 Fuse Usage Empty Steering Wheel Radio Controls Power Door Locks Empty Empty Empty...
Page 433 Fuse Usage Power Seats Electronic Level Control (ELC) Compressor Liftgate and Endgate Rear Auxiliary Power Outlet Electronic Level Control (ELC) Compressor Relay and Height Sensor Heated Mirrors Power Mirrors Ignition 1 Module Turn Signal Switch Rear Defogger Air Bag Module TCC Switch HVAC Blower Motor HVAC Mode and Temperature...
Page 434: Underhood Fuse Block
Underhood Fuse Block This fuse block is located in the engine compartment, on the passenger’s side of the vehicle. See Engine Compartment Overview on page 5-12 for more information on location. The back-up lamp relay (A) is located to the left of the underhood fuse block.
Page 435 Fuse Usage Fuel Pump Air Conditioning Compressor Clutch Horn Engine Controls-Emissions and Sensors Power Control Module (PCM)-Battery Power Anti-Lock Brakes (ABS) Control Module Transaxle Solenoids Anti-lock Brake System (ABS) Solenoid Valves Oxygen Sensors-Emissions Control Injectors Engine Controls Daytime Running Lamps (DRL) Passenger’s Low-Beam Headlamp Driver’s Low-Beam Headlamp Driver’s High-Beam Headlamp...
Page 436 Fuse Main Battery Fuse for Retained Accessory Power Relay and Accessory Relay Main Battery Fuse for Heated Seats, Main Battery Fuse for Power Outlets, Level Control, Power Seats and Mirrors and Body Computer Main Battery Fuse for Climate Control Blower and Ignition 3 Relay Main Battery Fuse for Ignition Switch, Radio, Heads-Up Display, Remote Keyless Entry (RKE),...
Page 437: Capacities And Speciﬁcations
Capacities and Speciﬁcations The following approximate capacities are given in English and metric conversions. Refer to Recommended Fluids and Lubricants on page 6-12 for more information. Application Air Conditioning Refrigerant (R134a) Automatic Transaxle Pan Removal and Replacement Complete Overhaul AWD Automatic Transaxle Pan Removal and Replacement Complete Overhaul Cooling System with A/C...
Page 438: Engine Speciﬁcations
Engine Speciﬁcations Engine VIN Code Transaxle Spark Plug Gap Automatic 0.060 inches (1.52 mm) 5-116...
Page 439 Section 6 Maintenance Schedule ...6-2 Introduction ...6-2 Maintenance Requirements ...6-2 Your Vehicle and the Environment ...6-2 Using Your Maintenance Schedule ...6-2 Scheduled Maintenance ...6-4 Additional Required Services ...6-6 Maintenance Footnotes ...6-7 Maintenance Schedule Owner Checks and Services ...6-8 At Each Fuel Fill ...6-8 At Least Once a Month ...6-9 At Least Once a Year ...6-9 Recommended Fluids and Lubricants ...6-12...
Page 440: Maintenance Schedule
Maintenance Schedule Introduction Important: Keep engine oil at the proper level and change as recommended. Have you purchased the GM Protection Plan? The Plan supplements your new vehicle warranties. See your Warranty and Owner Assistance booklet or your dealer for details. Maintenance Requirements Notice: Maintenance intervals, checks, inspections, replacement parts and recommended ﬂuids and...
Page 441 This schedule is for vehicles that: • carry passengers and cargo within recommended limits. You will ﬁnd these limits on the tire and loading information label. See Loading Your Vehicle on page 4-36. • are driven on reasonable road surfaces within legal driving limits.
Page 442: Scheduled Maintenance
Scheduled Maintenance When the CHANGE ENGINE OIL message comes on, it means that service is required for your vehicle. Have your vehicle serviced as soon as possible within the next 600 miles (1 000 km). It is possible that, if you are driving under the best conditions, the engine oil life system may not indicate that vehicle service is necessary for over a year.
Page 443 Service Maintenance I Maintenance II Change engine oil and ﬁlter. Reset oil life system. See Engine Oil on page 5-14. An Emission Control Service. Visually check for any leaks or damage. See footnote (j). Inspect engine air cleaner ﬁlter. If necessary, replace ﬁlter. See Engine Air Cleaner/Filter on page 5-19.
Page 444: Additional Required Services
Additional Required Services The following services should be performed at the ﬁrst maintenance service (I or II) after the indicated miles (kilometers) shown for each item. Service Inspect fuel system for damage or leaks. Inspect exhaust system for loose or damaged components.
Page 445: Maintenance Footnotes
Maintenance Footnotes † The U.S. Environmental Protection Agency or the California Air Resources Board has determined that the failure to perform this maintenance item will not nullify the emission warranty or limit recall liability prior to the completion of the vehicle’s useful life. We, however, urge that all recommended maintenance services be performed at the indicated intervals and the maintenance be recorded.
Page 446: Owner Checks And Services
(h) Change automatic transaxle ﬂuid and ﬁlter if the vehicle is mainly driven under one or more of these conditions: − In heavy city traffic where the outside temperature regularly reaches 90°F (32°C) or higher. − In hilly or mountainous terrain. −...
Page 447: At Least Once A Month
At Least Once a Month Tire Inﬂation Check Visually inspect your tires and make sure tires are inﬂated to the correct pressures. Don’t forget to check your spare tire. See Tires on page 5-57 for further details. Check to make sure the spare tire is stored securely.
Page 448: Ignition Transaxle Lock Check
Automatic Transaxle Shift Lock Control System Check CAUTION: When you are doing this inspection, the vehicle could move suddenly. If the vehicle moves, you or others could be injured. 1. Before you start, be sure you have enough room around the vehicle. It should be parked on a level surface.
Page 449: Underbody Flushing Service
Parking Brake and Automatic Transaxle Park (P) Mechanism Check CAUTION: When you are doing this check, your vehicle could begin to move. You or others could be injured and property could be damaged. Make sure there is room in front of your vehicle in case it begins to roll.
Page 450: Recommended Fluids And Lubricants
Recommended Fluids and Lubricants Fluids and lubricants identiﬁed below by name, part number or speciﬁcation may be obtained from your dealer. Usage Fluid/Lubricant Engine oil which meets GM Standard GM6094M and displays the American Petroleum Institute Certiﬁed for Gasoline Engines Engine Oil starburst symbol.
Page 451: Normal Maintenance Replacement Parts
Normal Maintenance Replacement Parts Part Engine Air Cleaner/Filter Engine Oil Filter Spark Plugs Windshield Wiper Blades Driver’s Side Length Passenger’s Side Length Type Engine Drive Belt Routing ® Part Number ACDelco 25099149 A1208C 25010792 12568387 41–101 24.0 inches (60.0 cm) 22.0 inches (55.0 cm) Shepherd’s Hook ®...
Page 452: Maintenance Record
Maintenance Record After the scheduled services are performed, record the date, odometer reading, who performed the service and the type of services performed in the boxes provided. See Maintenance Requirements on page 6-2 in this section. Any additional information from Owner Checks and Services on page 6-8 can be added on the following record pages. Also, you should retain all maintenance receipts.
Page 453 Maintenance Record (cont’d) Odometer Maintenance I or Services Performed Date Serviced By Reading Maintenance II 6-15...
Page 454 Maintenance Record (cont’d) Odometer Maintenance I or Services Performed Date Serviced By Reading Maintenance II 6-16...
Page 455 Section 7 Customer Assistance Information ...7-2 Customer Satisfaction Procedure ...7-2 Online Owner Center ...7-4 Customer Assistance for Text Telephone (TTY) Users ...7-4 Customer Assistance Offices ...7-5 GM Mobility Program for Persons with Disabilities ...7-6 Roadside Assistance Program ...7-6 Courtesy Transportation ...7-8 Vehicle Data Collection and Event Data Records ...7-10 Customer Assistance Information...
Page 456: Customer Assistance Information
Information Customer Satisfaction Procedure Your satisfaction and goodwill are important to your dealer and to Buick. Normally, any concerns with the sales transaction or the operation of your vehicle will be resolved by your dealer’s sales or service departments. Sometimes, however, despite the best intentions of all concerned, misunderstandings can occur.
Page 457 STEP THREE: Both General Motors and your dealer are committed to making sure you are completely satisﬁed with your new vehicle. However, if you continue to remain unsatisﬁed after following the procedure outlined in Steps One and Two, you should ﬁle with the BBB Auto Line Program to enforce any additional rights you may have.
Page 458: Online Owner Center
To assist customers who are deaf, hard of hearing, or speech-impaired and who use Text Telephones (TTYs), Buick has TTY equipment available at its Customer Assistance Center. Any TTY user can communicate with Buick by dialing: 1-800-83-BUICK. (TTY users in Canada...
Page 459: Customer Assistance Offices
Customer Assistance Offices Buick encourages customers to call the toll-free number for assistance. If a U.S. customer wishes to write to Buick, the letter should be addressed to Buick’s Customer Assistance Center. United States – Customer Assistance Buick Customer Assistance Center P.O.
Page 460: Gm Mobility Program For Persons With Disabilities
1-800-GM-DRIVE (463-7483) for details. All TTY users call 1-800-263-3830. Roadside Assistance Program Buick Motor Division is proud to offer Buick Premium Roadside Assistance to customers for vehicles covered under the 3 year/36,000 mile (60 000 km) new car warranty (whichever occurs ﬁrst).
Page 461: Canadian Roadside Assistance
• Vehicle license plate number Buick reserves the right to limit services or reimbursement to an owner or driver when, in Buick’s judgement, the claims become excessive in frequency or type of occurrence. While we hope you never have the occasion to use our service, it is added security while traveling for you and your family.
Page 462: Courtesy Transportation
Transportation Options Warranty service can generally be completed while you wait. However, if you are unable to wait Buick helps minimize your inconvenience by providing several transportation options. Depending on the circumstances,...
Page 463: Additional Program Information
Courtesy Rental Vehicle Your dealer may arrange to provide you with a courtesy rental vehicle or reimburse you for a rental vehicle you obtained if your vehicle is kept for a warranty repair. Reimbursement will be limited to a maximum of $30 a day and must be supported by receipts.
Page 464: Vehicle Data Collection And Event Data Records
Vehicle Data Collection and Event Data Records Your vehicle, like other modern motor vehicles, has a number of sophisticated computer systems that monitor and control several aspects of the vehicle’s performance. Your vehicle uses on-board vehicle computers to monitor emission control components to optimize fuel economy, to monitor conditions for airbag deployment and, if so equipped, to provide anti-lock braking and to help the driver control the...
Page 465: Reporting Safety Defects
In addition to notifying NHTSA (or Transport Canada) in a situation like this, we certainly hope you’ll notify us. Please call us at 1-800-521-7300, or write: Buick Customer Assistance Center P.O. Box 33136 Detroit, MI 48232-5136 In Canada, please call us at 1-800-263-3777 (English) or 1-800-263-7854 (French).
Page 466: Service Publications Ordering Information
Service Publications Ordering Information Service Manuals Service Manuals have the diagnosis and repair information on engines, transmission, axle, suspension, brakes, electrical, steering, body, etc. RETAIL SELL PRICE: $120.00 Transmission, Transaxle, Transfer Case Unit Repair Manual This manual provides information on unit repair service procedures, adjustments, and speciﬁcations for GM transmissions, transaxles, and transfer cases.
Page 467: Current And Past Model Order Forms
Current and Past Model Order Forms Service Publications are available for current and past model GM vehicles. To request an order form, please specify year and model name of the vehicle. ORDER TOLL FREE: 1-800-551-4123 Monday-Friday 8:00 AM - 6:00 PM Eastern Time For Credit Card Orders Only (VISA-MasterCard-Discover), visit Helm, Inc.
Page 468 NOTES 7-14...
Page 469 About Driving Your Vehicle ... 4-2 Accessory Inﬂator ... 5-74 Accessory Power Outlets ... 3-27 Adding Washer Fluid ... 5-38 Additional Program Information ... 7-9 Additives, Fuel ... 5-6 Add-On Electrical Equipment ... 5-108 Adjusting the Captain’s Chairs (Second Row) ... 1-14 Adjusting the Speakers (Balance/Fade) ...
Page 470 Audio System(s) (cont.) Radio with Six-Disc CD ... 3-98 Rear Seat Audio (RSA) ... 3-126 Setting the Time ... 3-73 Theft-Deterrent Feature ... 3-128 Understanding Radio Reception ... 3-130 XM™ Satellite Radio Antenna System ... 3-132 Auto Door Lock/Unlock ... 3-67 Automatic Headlamp System ...
Page 471 Care of (cont.) Your CDs and DVDs ... 3-131 Cargo Cover ... 2-44 Cargo Lamp ... 3-20 Carrier Assembly-Differential (Rear Drive Module) ... 5-49 Cassette Tape Messages ... 3-94 CD Adapter Kits ... 3-95 CD Messages ... 3-84, 3-97, 3-111 Cell Phone Storage Area ...
Page 472 Cleaning Tires ... 5-105 Cleaning Vinyl ... 5-101 Climate Control System ... 3-28 Dual ... 3-32 Dual Automatic ... 3-35 Outlet Adjustment ... 3-38 Compact Spare Tire ... 5-98 Compass Variance ... 3-60 Content Theft-Deferrent ... 2-15 Control of a Vehicle ... 4-7 Convenience Center, Rear ...
Page 473 Door (cont.) Programmable Automatic Door Locks ... 2-10 Rear Door Security Locks ... 2-10 Driver Four-Way Manual Seat ... 1-3 Position, Safety Belt ... 1-28 Driver Behavior ... 4-2 Driver Information Center (DIC) ... 3-60 DIC Controls and Displays ... 3-62 DIC Vehicle Personalization ...
Page 474 Engine (cont.) Drive Belt Routing ... 6-13 Engine Compartment Overview ... 5-12 Exhaust ... 2-30 Oil ... 5-14 Overheating ... 5-26 Starting ... 2-21 Engine Oil Additives ... 5-17 Engine Speciﬁcations ... 5-116 Entering Programming Mode ... 3-64 Entertainment System Cleaning Your DVD Player ...
Page 475 Following Distance ... 4-48 Four-Way Manual Driver Seat ... 1-3 Front Armrest Storage Area ... 2-40 Front Console Storage Area ... 2-40 Front Reading Lamps ... 3-20 Fuel ... 5-4 Additives ... 5-6 California Fuel ... 5-5 Filling a Portable Fuel Container ... 5-9 Filling Your Tank ...
Page 476 Hitches ... 4-46 ® HomeLink Transmitter ... 2-35 ® HomeLink Transmitter, Programming ... 2-35 Hood Checking Things Under ... 5-10 Release ... 5-11 Horn ... 3-7 How the System Works ... 3-26 How to Add Automatic Transaxle Fluid ... 5-23 How to Add Coolant to the Coolant Recovery Tank ...
Page 477 Lamps Exterior ... 3-14 Interior ... 3-16 Lamps on Reminder ... 3-14 Lap-Shoulder Belt ... 1-28, 1-39, 1-42 LATCH System Child Restraints ... 1-62 Securing a Child Restraint Designed for the LATCH System ... 1-64 Leaving Your Vehicle ... 2-11 Leaving Your Vehicle With the Engine Running ...
Page 478 Maintenance Schedule (cont.) Maintenance Footnotes ... 6-7 Maintenance Record ... 6-14 Maintenance Requirements ... 6-2 Normal Maintenance Replacement Parts ... 6-13 Owner Checks and Services ... 6-8 Recommended Fluids and Lubricants ... 6-12 Scheduled Maintenance ... 6-4 Using Your ... 6-2 Your Vehicle and the Environment ...
Page 479 Navigation/Radio System ... 3-112 New Vehicle Break-In ... 2-19 Normal Maintenance Replacement Parts ... 6-13 Odometer ... 3-41 Off-Road Recovery ... 4-15 Engine ... 5-14 Pressure Message ... 3-52 Older Children, Restraints ... 1-47 Online Owner Center ... 7-4 ® OnStar Personal Calling ...
Page 480 Perimeter Lighting ... 3-19 Plan Ahead When Possible ... 7-8 Playing a Cassette Tape ... 3-93 Playing a CD ... 3-83, 3-95, 3-107 Playing a Speciﬁc Loaded CD ... 3-108 Playing the Radio ... 3-75, 3-86, 3-99 Power Accessory Outlets ... 3-27 Door Locks ...
Page 481 Rear Seat Operation ... 1-9 Rear Seat Outside Passenger Positions ... 1-38 Rear Seat Passengers, Safety Belts ... 1-38 Rear Storage Area ... 2-40 Rear Window Defogger ... 3-31, 3-34, 3-38 Rearview Mirrors ... 2-32 Reclining Seatbacks ... 1-6 Recommended Fluids and Lubricants ... 6-12 Recreational Vehicle Towing ...
Page 482 Safety Belt Pretensioners ... 1-46 Reminder Light ... 3-43 Safety Belts Care of ... 5-102 Center Rear Passenger Position ... 1-42 Driver Position ... 1-28 How to Wear Safety Belts Properly ... 1-27 Questions and Answers About Safety Belts ... 1-26 Rear Safety Belt Comfort Guides for Children and Small Adults ...
Page 483 Service Manuals ... 7-12 Setting Preset PTYs (RDS Only) ... 3-102 Setting Preset Stations ... 3-76, 3-87, 3-100 Setting the Time ... 3-73 Setting the Tone (Bass/Treble) ... 3-76, 3-88, 3-100 Sheet Metal Damage ... 5-105 Shifting Into Park (P) ... 2-27 Shifting Out of Park (P) ...
Page 484 Tilt Wheel ... 3-7 Tips and Trouble ... 3-123 Tire Low Message ... 3-54 Tire Sidewall Labeling ... 5-58 Tire Size ... 5-61 Tire Terminology and Deﬁnitions ... 5-62 Tires ... 5-57 Buying New Tires ... 5-70 Chains ... 5-74 Changing a Flat Tire ...
Page 485 Ultrasonic Rear Parking Assist (URPA) ... 3-24 Underhood Fuse Block ... 5-112 Understanding Radio Reception ... 3-130 Uniform Tire Quality Grading ... 5-71 United States – Customer Assistance ... 7-5 Unlock Feedback ... 3-69 Used Replacement Wheels ... 5-73 Using Cleaner on Fabric ... 5-100 ®...
Page 486 What Washer Fluid to Use ... 5-37 Wheels Alignment and Tire Balance ... 5-72 Replacement ... 5-72 When to Add Engine Oil ... 5-15 When to Change Engine Oil (GM Oil Life System) ... 5-18 When to Check ... 5-65 When to Check and Change Automatic Transaxle Fluid ...

This manual is also suitable for:

Rendez 2004

Buick 2004 Rendezvous Owner's Manual

Table of Contents

Seats and Restraint Systems

Features and Controls

Instrument Panel

Section 3 Instrument Panel

Maintenance Schedule

Driver Information Center (DIC)

Section 4 Driving Your Vehicle

Your Driving, the Road, and Your Vehicle

Towing

Quick Links

Chapters

Related Manuals for Buick 2004 Rendezvous

Summary of Contents for Buick 2004 Rendezvous