Ordering Spare Parts; Maintenance And Repairs - Stihl MS 261 C-M Instruction Manual

35 Ordering Spare Parts

Groove width:
Sprocket nose:
34.6.2 Rollomatic Guide Bars
Bar lengths (pitch .325"): 40, 45, 50 cm
Groove width:
Sprocket nose:
34.6.3 Rollomatic Light 04 guide bars
Bar lengths (pitch .325"): 35, 40, 45, 50 cm
Groove width:
Sprocket nose:
34.6.4 Rollomatic Guide Bars
Bar lengths (pitch .325"): 32, 37, 40, 45 cm
Groove width:
Sprocket nose:
34.6.5 Duromatic guide bars
Bar lengths (pitch .325"): 37, 40, 45 cm
Groove width:
34.6.6 Saw chains .325"
Rapid Micro (23 RM) Type 3684
Rapid Micro 3 (23 RM3) Type 3687
Rapid Super (23 RS) Type 3637
Rapid Duro 3 (23 RD3) Type 3665
Rapid Micro Pro (23 RM Pro) 3693
Rapid Micro 3 Pro (23 RM3 Pro) 3695
Rapid Super Pro (23 RS Pro) 3690
Rapid Duro 3 Pro (23 RD3 Pro) 3696
Pitch:
Drive link gauge:
Rapid Micro (26 RM) Type 3686
Rapid Micro 3 (26 RM3) Type 3689
Rapid Super (26 RS) Type 3639
Pitch:
Drive link gauge:
34.6.7 Chain sprocket
7-tooth for .325"
Max. chain speed according to
ISO 11681:
Chain speed at maximum power:
34.7 Noise and Vibration Data
For further details on compliance with Vibration
Directive 2002/44/EC visit www.stihl.com/vib.
34.7.1 Sound pressure level L
105 dB(A)
34.7.2 Sound power level L
116 dB(A)
34.7.3 Vibration measurement a
22867
Left handle:
Right handle:
0458-153-0121-C
1.3 mm
10 tooth
1.3 mm
11 tooth
1.6 mm
10 tooth
1.6 mm
11 tooth
1.6 mm
.325" (8.25 mm)
1.3 mm
.325" (8.25 mm)
1.6 mm
25.6 m/s
19.3 m/s
to ISO 22868
p
to ISO 22868
w
to ISO
hv,eq
2
3.5 m/s
2
3.5 m/s
The K‑factor in accordance with Directive
2006/42/EC is 2.0 dB(A) for the sound pressure
level and sound power level; the K‑factor in
accordance with Directive 2006/42/EC is
2
2.0 m/s for the vibration level.
34.8 REACH
REACH is an EC regulation and stands for the
Registration, Evaluation, Authorisation and
Restriction of Chemical substances.
For information on compliance with the REACH
regulation (EC) No. 1907/2006 see
www.stihl.com/reach.
34.9 Exhaust Emissions
The CO value measured in the EU type approval
2
procedure is specified at www.stihl.com/co2.
The measured CO value was determined on a
2
representative engine in accordance with a
standardized test procedure under laboratory
conditions and does not represent either an
explicit or implied guarantee of the performance
of a specific engine.
The applicable exhaust emission requirements
are fulfilled by the intended usage and mainte‐
nance described in this instruction manual. The
type approval expires if the engine is modified in
any way.
35 Ordering Spare Parts
Please enter your saw model, serial number as
well as the part numbers of the guide bar and
saw chain in the spaces provided. This will make
re-ordering simpler.
The guide bar and saw chain are subject to nor‐
mal wear and tear. When purchasing these
parts, always quote the saw model, the part
numbers and names of the parts.
Model
Serial number
Guide bar part number
Chain part number

36 Maintenance and Repairs

Users of this machine may only carry out the
maintenance and service work described in this
English
41