DeWalt DW682 Instruction Manual page 3

FIG 12
FIG 15
FIG 18
3/16" (5 MM) MINIMUM
MINIMUM DE 5 MM (3/16 PO)
4,7 MM (3/16") MINIMO
3/16" MINIMUM
MINIMUM DE 5 MM (3/16 PO)
4,7 MM (3/16") MINIMO
FIG 21
5. EDGE MITER JOINTS (See Figure 24)
Edge miters are most commonly used in box structures or for making multisided
pedestals where you would like to hide the end grain. Once again, biscuit joinery is an out-
standing method to use both for added strength as well as ease of assembly. Follow the
steps below to assemble a 90° joint.
A. Position the workpieces as they are to be assembled and layout biscuit locations on
the outside of the joint.
B. Set up tool by first setting fence angle to 90°. Make the fence adjustment such that the
biscuit is located toward the inside of the joint where the material is thicker, then select
the biscuit size so that the blade does not protrude through the outside wall when the
cut is made (see Figure 25).
C. Clamp the workpiece and align the tool as shown in column in Figure 26.
D. Turn on the tool and make the plunge cut.
E. Glue, assemble and clamp the joint.
F. For joints other than 90° see outside registration column Figure 27 for proper fence
angle setting.
The above method will produce a joint where the outside surfaces of the joint are aligned. If
you wish to produce a joint where the inside surfaces are aligned, use the following proce-
dures for a 90° joint.
A. Position workpieces as they are to be assembled.
B. Layout biscuit locations on the inside of the angle.
C. Set up tool by setting fence angle to 45°. Set vertical fence adjustment so that the bis-
cuit is located toward the inside of the joint where material is thicker. Select biscuit size
so that the blade does not protrude through the outside face of the material.
D. Clamp the workpiece and align the tool as shown in Figure 28.
E. Make the plunge cut and repeat for all biscuit locations.
F. Glue, assemble and clamp the joint.
G. For joints other than 90° see inside registration column in Figure 27 for proper fence
angle setting.
6. T-JOINTS (Figure 29)
Biscuit joining is a viable alternative to dadoing when making a T-joint. T-joints are most
commonly used when attaching shelves to the sides of a case. The method described
below will work if your shelf material is at least 5/8" thick.
A. Place the workpieces on a work surface exactly as you will be assembling them in the
form of an upside down "T." Mark lightly along the joint where the top of the shelf is to
end up (see Figure 30). Mark biscuit locations at the joint interface on the shelf piece
only.
B. Lay the shelf down on the mating workpiece. Clamp the two workpieces together and
to the work surface in this position (see Figure 31).
C. Set up the tool by selecting the proper biscuit size and setting the adjustable fence
angle at 0°.
D. Using the bottom registration surface, align the tool with the biscuit location marks and
make a vertical and a horizontal plunge cut for each biscuit location as shown in
Figure 32.
E. Glue, assemble and clamp the joint.
Accessories
Recommended accessories for use with your tool are available at extra cost from your local
dealer or authorized service center. If you need assistance in locating any accessory for your
tool, please contact your local dealer or authorized service center.
CAUTION: The use of any other accessory not recommended for use with this tool could
be hazardous.
Motor Brushes
D WALT uses an advanced brush system which automaticallystops the drill when the brush-
E
es wear out. This prevents serious damage to the motor.
Repairs
To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (includ-
ing brush inspection and replacement) should be performed by authorized service centers or
other qualified service organizations, always using identical replacement parts.
Three Year Limited Warranty
D WALT will repair, without charge, any defects due to faulty materials or workmanship for
E
three years from the date of purchase. This warranty does not cover part failure due to nor-
mal wear or tool abuse. For further detail of warranty coverage and warranty repair informa-
tion, visit www.dewalt.com or call 1-800-4-D
apply to accessories or damage caused where repairs have been made or attempted by oth-
ers. This warranty gives you specific legal rights and you may have other rights which vary in
certain states or provinces.
In addition to the warranty, D WALT tools are covered by our:
E
1 YEAR FREE SERVICE
D WALT will maintain the tool and replace worn parts caused by normal use, for free, any
E
time during the first year after purchase.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your D
or Nailer for any reason, you can return it within 90 days from the date of purchase with a
receipt for a full refund – no questions asked.
RECONDITIONED PRODUCT: Reconditioned product is covered under the 1 Year Free
Service Warranty. The 90 Day Money Back Guarantee and the Three Year Limited Warranty
do not apply to reconditioned product.
FREE WARNING LABEL REPLACEMENT: If your warning labels (Fig. 33) become illegible
or are missing, call 1-800-4-DEWALT for a free replacement.
FIG 13
FIG 16
2"-3"
FIG 19
3/16" (5 MM) MINIMUM
MINIMUM DE 5 MM (3/16 PO)
4,7 MM (3/16") MINIMO
FIG 22
WALT (1-800-433-9258). This warranty does not
E
WALT Power Tool, Laser,
E
PROTRUDING BISCUIT END
(TRIM OFF WITH SAW
AND SAND SMOOTH)
EXTRÉMITÉ DE BISCUIT SAILLANTE
(DÉCOUPER À L'AIDE D'UNE
SCIE ET PONCER.)
EXTREMO SOBRESALIENTE
DE LA LENGÜETA (RECORTE
CON SIERRA Y LIJE)
6"-10"
FIG 23
FIG 24
FIG 26
REVERSE 45° BEVEL: ALLOWS OUTSIDE
REGISTRATION ON MITER JOINTS.
(NOTE: THE TOOL IS REGISTERED
AGAINST THE OUTSIDE SURFACE.)
BISEAU INVERSÉ DE 45° : SURFACE DE CONTACT
EXTÉRIEURE SUR LES JOINTS EN BISEAU.
(NOTE : L'OUTIL REPOSE SUR LA SURFACE
BISEL INVERTIDO A 45 : PERMITE REGISTRO
EXTERIOR EN ENSAMBLES ANGULARES.
(NOTA: LA HERRAMIENTA SE REGISTRA CONTRA
LA SUPERFICIE EXTERNA.)
FIG 27
FIG 28
FIG 30
FIG 32
FIG 14
1" OR GREATER STOCK THICKNESS
PIÈCES DE PLUS DE 25 MM (1 PO) D'ÉPAISSEUR
MADERA DE 25MM (1") DE ESPESOR O MAYOR
FIG 17
FIG 20
FIG 25
TO INSIDE EDGE TO INCREASE DIMEN-
AUGMENTER LA DIMENSION «A».
COLOQUE LA LENGÜETA CERCA AL
BORDE INTERIOR PARA AUMENTAR LA
EXTÉRIEURE.)
FIG 29
FIG 31
FIG 33
POSITION BISCUIT CLOSER
SION "A"
PLACER LE BISCUIT VERS
L'INTÉRIEUR DE FAÇON À
DIMENSION "A"
INSIDE EDGE
INTÉRIEUR
INTERIOR
A
"T" JOINT
ASSEMBLAGE EN T
ENSAMBLE EN "T"
LAYOUT LINE
LIGNE DE DISPOSITION
LINEA DE TRAZO