Dell 4200 Installation Manual
Dell poweredge 4200 servers: installation guide
Hide thumbs
Also See for 4200:
- Installation and troubleshooting manual (154 pages) ,
- User manual (132 pages) ,
- Solution manual (114 pages)
Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Dell 4200
Summary of Contents for Dell 4200
- Page 1 Dell™ PowerEdge™ 4x00 and 6300 Systems Tower Installation Guide Systèmes Dell™ PowerEdge™ 4x00 et 6300 Guide d’installation en tour Dell™ PowerEdge™ 4x00 und 6300 Systeme Tower-Installationshandbuch Sistemas Dell™ PowerEdge™ 4x00 y 6300 Guía de instalación en torre ™ www.dell.com...
- Page 3 ™ Dell™ PowerEdge™ 4x00 and 6300 Systems TOWER INSTALLATION GUIDE www.dell.com...
- Page 4 Information in this document is subject to change without notice. © 1999 Dell Computer Corporation. All rights reserved. Trademarks used in this text: Dell, the DELL logo, and PowerEdge are trademarks of Dell Computer Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products.
-
Page 5: Table Of Contents
Contents Before You Begin ..........1-2 Important Safety Information . - Page 6 Figure 1-6. Figure 1-7. Figure 1-8. Figure 1-9. Figure 1-10. Removing a Cage Nut ........1-12 Figure 1-11.
-
Page 7: Installation Guide
6300 Systems Tower Installation Guide This installation guide provides instructions for trained service technicians converting one or more Dell PowerEdge 4x00 or 6300 rack-mounted computer systems into a tower configuration. WARNING: The power supplies in this computer system produce high voltages and energy hazards, which can cause bodily harm. -
Page 8: Before You Begin
This tower kit is intended to be installed by trained service technicians. Rack Stabilizer Feet WARNING: Removing PowerEdge systems from a Dell rack without the front and side stabilizer feet installed could cause the rack to tip over, potentially resulting in bodily injury under certain circumstances. -
Page 9: Recommended Tools
The stabilizer feet help prevent the possibility of the rack tipping over when a system or other components are pulled out of the rack far enough so that the slide assemblies are fully extended. Refer to the Dell PowerEdge Rack-Mountable Solutions Installation Guide provided with the rack for instructions on installing the stabilizer feet. -
Page 10: Removing The Doors From A 24-U Or 42-U Rack
If you have a 42-unit (U [1.75 inches]) rack, perform the following steps (see Figure 1-3): Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide One person should grasp the top of the door to stabilize it. The other person should grasp the bottom of the door. -
Page 11: Figure 1-3. Removing The 42-U Rack Doors
Store the doors in an area where they will not fall over while you install the kit. support.dell.com With the door open, lift out and fully retract all hinge pins. Lift the door out carefully. Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide hinge release lever... -
Page 12: Removing The Cable Management Arm
(see Figure 1-5). Fold the cable management arm and place the arm, together with all attaching hardware, in a container for future use. Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide hinge insert hinge pin... -
Page 13: Removing The Cable Tray
Phillips-head screws that secure the tray to the system chassis (see Figure 1-6). support.dell.com 10-32 x 0.5-inch screw vertical rail cable-management arm back of computer cable tray 10-32 x 0.25-inch screws (3) Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide right-angle bracket... -
Page 14: Removing The System From The Rack
Press the green button near the end of each interior slide to release the slide locks (see Figure 1-7), and then slide the system completely out of the rack. Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide back of computer cable tray 6-32 x 0.25-inch screws (5) -
Page 15: Removing The Rails And Rack Adapters
Remove the three rails on each side of the system (see Figure 1-8). Remove each rail by removing the four 10-32 x 0.25-inch Phillips-head screws that secure the rail to the system chassis. support.dell.com interior slide thumbscrews (4) Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide green push button... -
Page 16: Removing The Slide Assemblies From The Rack
Remove the two 10-32 x 0.5-inch Phillips-head screws that secure the slide’s mounting bracket to the front of the rack. 1-10 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide install plastic filler plugs on this side only rack adapters (2) 10-32 x 0.25-inch screws (3) -
Page 17: Figure 1-9. Removing The Slide Assemblies
Repeat this step to remove the remaining cage nuts. Package all the rack installation hardware you removed and label it for future use. support.dell.com front of rack Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide slide-assembly mounting-bracket flange alignment... -
Page 18: Replacing The Rack Doors
(see Figure 1-2). Repeat steps 1 through 4 to install the back door. 1-12 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide cage-nut installation tool cage nut... -
Page 19: Installing The Rubber Feet
(screws and rubber feet at provided with the kit), as shown in Figure 1-11. Figure 1-11. Installing the Rubber Feet support.dell.com Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide 8-32 x 0.5-inch screw rubber feet (4) 1-13... -
Page 20: Removing The Front Bezel
Rotate the bezel to the left to disengage and remove it. 1-14 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide Turn the keylock on the back edge of the cover to the unlocked position. Slide the cover about a centimeter (half an inch) toward the back of the system. -
Page 21: Reorienting Drives
Pull the frame out of the bezel. Rotate the frame 90 degrees to match the new orientation of the drives. Replace the frame in the front bezel and carefully press it into place. Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide system badge... -
Page 22: Reorienting The System Badge
Reinstall the system cover. 1-16 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide Disconnect the DC power cable and the interface cable from the back of the drive. Be sure to record the power connector number and the location of the interface connector. -
Page 23: Attaching Cables And Turning The System On
Plug the other end of the power cable into an AC receptacle of the proper current rating. Turn on the system and all attached peripherals. Ensure that the power-on self-test (POST) successfully completes and that the operating system boots. support.dell.com Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide 1-17... - Page 24 1-18 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide...
-
Page 25: Index
1-14 replacing, 1-16 cable management arm removing, 1-6 cable tray removing, 1-7 cables connecting, 1-17 disconnecting, 1-6 cage nuts removing, 1-11 support.dell.com doors opening latch, 1-4 removing, 1-4 replacing, 1-12 drives reorienting, 1-15 feet installing, 1-13 kit contents illustrated, 1-2... - Page 26 1-10 stabilizer feet, 1-2 system removing rails, 1-9 weight, 1-9 system badge reorienting, 1-16 Dell PowerEdge 4x00 and 6300 Systems Tower Installation Guide tools recommended, 1-3 tower kit contents illustrated, 1-2 list of, 1-1 tower kit installation rack adapters, removing, 1-9...
- Page 28 Printed in the U.S.A. Imprimé aux U.S.A. Gedruckt in den U.S.A. Impreso en los EE.UU. ™ *26JVW* P/N 26JVW Rev. A00 www.dell.com...