DeWalt DW755 Original Instructions Manual page 26

EngLIsh
5. Place a new belt over the pulleys
arrow on the inside of the belt points in the same direction
as the arrow 21 on the backing plate.
6. Release the lever.
7. Holding the threaded pin
22
backing plate.
8. Replace the knob and tighten it.

WARNING: When mounting a leather honing belt, make
sure that the leather surface is on the outside.
Adjusting the Grinding or Honing Belt
(Fig. E)
Centering the Belt
1. If the belt 5 is not properly centered, adjust by turning the
centering knob 8 .
2. Slacken the hexagonal head bolts
plate 24 to minimise the clearance with the belt. Tighten
the bolts
Adjusting the Belt to the Workpiece
The belt can be adjusted to suit workpieces with concave,
convex or straight cutting edges.
1. Slacken the knob 10 .
2. Set the backing plate 18 to the appropriate position (up,
flush or down).
3. Tighten the knob .
10
Preparing the Honing Belt For Use
Leather honing belts must be dressed before first use and when
the honing effect decreases.
With the machine switched off, spread a thin and even coating
of honing paste over the entire outside surface of the belt.
Mounting the Spark Guard (Fig. F, G)
The spark guard offers additional protection from sparks and
must be used whenever possible.
1. Fit the transparent screen 25
inserting a mushroom head bolt
guard and placing a washer
(Fig. F). Tighten the nut.
2. Hold the spark guard against the edge on top of the wheel
case as shown (Fig. G).
29
3. Insert a mushroom head bolt
wheel case.
4. Place a washer 31 and nut
the nut hand-tight.
5. Position the guard at a distance of approx.
2 mm from the wheel by sliding it towards the wheel.
6. Securely tighten the nut (torque: 6 Nm).
Adjusting the Workpiece Support (Fig. H)
The workpiece support can be set according to the workpiece
and the desired grinding angle.
1. Slacken the nut holding the support
24
, making sure that the
20
in its place, replace the
and adjust the
23
to the spark guard 6 by
26 into the screen and the
and nut onto the bolt
27 28
30 into the guard and the
32 onto the bolt and tighten
3 .
2. Set the support to the desired position and angle, making
sure that the support is as close to the wheel as possible.
3. Tighten the nut (torque: 6 Nm).
Mounting and Adjusting the Clamping and
Grinding Attachment (Fig. A, I)
The clamping and grinding attachment is used to hold the
workpiece to the grinding wheel at a fixed angle.
1. Remove the fasteners holding the workpiece support
the bracket 4 and remove the workpiece support (Fig. A).
2. Mount the grinding attachment bracket
bracket on the machine as shown using the hexagonal
4
head bolt 34 and corresponding nut
that the grinding attachment bracket is at a distance of
approx. 2 mm from the grinding wheel.
3. Insert the rod 36 of the grinding attachment into the forks
on the grinding attachment bracket as shown.
Mounting the Water Supply System
(Fig. D, J–M)
1. Remove the backing plate
2. Insert a screw into each of the bracket pairs
37
place a nut 39 a few turns on each screw (Fig. J).
3. Hook the bracket pairs 38
as shown (Fig. K).
4. Hold the water reservoir
41
shown and push it in its place with the brackets engaging in
the recesses 42 .
5. Tighten the nuts (Fig. J).
39
6. Replace the backing plate
7. Mount the flow regulator unit
case 40 using the screws
8. Place the hose between the water reservoir
45
flow regulator unit 43 (Fig. M).
9. In order to use the water supply system, it must be filled
with a sufficient amount of water.
a. Make sure the flow regulator
b. Unscrew the cap 47 .
c. Fill the container with cold water.
d. Screw the cap back on.
47
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect tool from power
source before making any adjustments or removing/
installing attachments or accessories. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
3
to the
33
35 (Fig. I). Make sure
18 (Fig. D).
and
38
to the back of the belt case 40
against the bracket pairs as
18 (Fig. D).
43 to the front of the belt
44 (Fig. L).
and the
41
46 is closed.
to