Page 2
Business Machines Corporation. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Computer Corporation disclaims any proprietary interest in trademarks and trade names other than its own.
Page 7
Figure A-12. Spreader and Keel Plate Removal .....A-27 Figure B-1. Dell Control Center Icon ......B-1 Figure B-2.
Page 8
A prerequisite for using this manual to service Dell portable computers is a basic knowledge of IBM compatible PC troubleshooting techniques. In addition to information provided in this manual, Dell provides the Reference and Troubleshooting Guide for troubleshooting procedures and instructions on using the Dell diagnostics to test portable computers, and the online System User’s Guide...
This chapter provides an overview of the features and technical specifications of this computer. ystem Features In addition to the standard features found in a Dell portable computer, the Dell Latitude XPi CD models include the following new features: •...
Figure 1-1. Front View of the Notebook Computer Dell Latitude XPi CD Service Manual hysical Description display assembly LCD panel keyboard trackball assembly diskette drive display assembly latch indicator panel tilt-support foot (2) main battery assembly speaker bottom case assembly...
The charging indicator is an amber LED. The indicator turns on when the main battery begins charging and blinks to show the battery is fully charged. Dell Latitude XPi CD Service Manual The first low-battery warning occurs when the main battery’s charge has been depleted to 8 percent of its fully charged condition.
Keyboard Indicators The keyboard controls the operation of the numeric lock (Num Lock) indicator, the capitals lock (Caps Lock) indicator, and the Scroll Lock indicator, all of which are visible through apertures at the top of the keyboard. These indicators are associated with the <NUM LOCK>...
IRQ13 IRQ14 IRQ15 Dell Latitude XPi CD Service Manual If the computer is in suspend mode (the power/suspend indicator flashes every 8 seconds), if the display is closed, and if no external monitor is attached, sliding the power button has no effect on the power state. The computer remains in suspend mode.
Page 16
Audio controller ....Stereo conversion ... . . FM music synthesizer..Dell Latitude XPi CD Service Manual Table 1-2. Technical Specifications Memory tRAC .
Page 17
8-ohm speakers 1 W into 8 ohms stereo 150 mW into 32 ohms stereo volume can be controlled through key combinations, software application menus, or the Speaker window in the Dell Control Center Video hardware-accelerated, 128-bit PCI NeoMagic 2090 1.1 MB...
Page 18
Life span (approximate) Temperature range: 1-10 Dell Latitude XPi CD Service Manual Table 1-2. Technical Specifications Height ....Depth ....
Page 19
Table 1-2. Technical Specifications Battery NiCad reserve battery: Voltage ....Operating time (approximate) ... . . Input voltage .
Page 20
Temperature: Relative humidity (maximum): Maximum vibration: 1-12 Dell Latitude XPi CD Service Manual Table 1-2. Technical Specifications CD-ROM Drive Random ....Full-stroke ....
These procedures can often reveal the source of a problem or indicate the correct starting point for troubleshooting the computer. Dell recom- mends that you perform these procedures in the order they are presented in this manual.
Page 24
3. Verify that the exterior of the computer is free of any obvious physical 4. If the computer is operating from an AC adapter, verify the following: Dell Latitude XPi CD Service Manual Look at the indicators to determine which of the following conditions apply, and then turn off the computer, taking the actions listed for that condition: •...
Page 25
5. If the computer is operating from battery power, remove the main bat- tery assembly, verify that it is free of any obvious physical damage, and then reinsert the battery assembly into its compartment. 6. Turn off the computer. Remove the hard-disk drive, verify that it is free of any obvious physical damage, and then reinsert the drive into its compartment.
NOTE: To prevent possible damage to the original diagnostics diskette, always use a backup copy of the diagnostics diskette when servicing a user’s computer. Dell recommends that users make copies of the Dell diagnostics diskette. For instructions, see “Before You Start Testing” in Chapter 4 of the Reference and Troubleshooting Guide.
If none of the procedures in this chapter reveal the source of the problem or lead to the proper troubleshooting steps for determining the source of the problem, call Dell for technical assistance. For instructions, see Chapter 5, “Getting Help,” in the Reference and Troubleshooting Guide.
If a faulty computer does not emit beep codes or display system error messages to indicate a failure, use the Dell diagnostics to help isolate the source of the problem. See “Running the Dell Diagnostics” found later in this chapter.
Page 30
4-2-1 4-2-2 4-2-3 4-2-4 4-3-1 4-3-3 4-3-4 4-4-1 4-4-2 4-4-3 Dell Latitude XPi CD Service Manual Table 3-1. POST Beep Codes Error Probable Causes Slave DMA register System board faulty failure Master DMA register failure Master interrupt mask System board faulty...
Table 3-1. POST Beep Codes Beep Code Error 5-1-1 System power- management interrupt initialization failure 5-1-2 BIOS shadowing failure 5-1-3 Video BIOS shadowing failure 5-2-1 Keyboard controller download failure 5-2-2 CPU stepping failure 5-2-3 System board failure 5-2-4 Setup decompression and shadowing failure ystem Error Messages The following table lists (in alphabetical order) system error messages that may...
Page 32
Diskette write- protected Drive not ready Error reading PCMCIA card Dell Latitude XPi CD Service Manual Table 3-2. System Error Messages Definition Informational message indicating memory is fail- ing (usually preceded by memory error message). Hard-disk drive failed to initialize.
Page 33
Table 3-2. System Error Messages Message Definition Amount of memory Extended memory recorded in NVRAM not size has changed matching memory installed in computer. Gate A20 failure Computer cannot enable protective mode. Message indicates sys- General failure tem failure. Computer cannot identify Hard-disk drive hard-disk drive type.
Page 34
Memory address line failure at address , read value expecting value Memory alloca- tion error Dell Latitude XPi CD Service Manual Table 3-2. System Error Messages Definition Keyboard key(s) jammed. Memory control logic not operating properly. The software in use...
Page 35
Table 3-2. System Error Messages Message Definition Memory not operating Memory data line properly. failure at address , read value expecting value Memory double word logic fail- ure at a ddress , read value expecting value Memory odd/even logic failure at address , read value expecting value...
The diagnostics contains tests that aid in troubleshooting the computer. If needed, see Chapter 4, “Running the Dell Diagnostics,” in the Reference and Troubleshooting Guide. The diagnostics diskette contains the following test groups: • •...
Page 37
To start the diagnostics, turn off the computer, insert a diagnostics diskette into the diskette drive, and then turn on the computer. Starting the diagnostics causes the Dell logo screen to appear, followed by a message indicating that the diagnostics is loading. Before the diagnostics loads, a program tests the portion of main memory (RAM) required for loading the diagnostics.
Page 38
3-10 Dell Latitude XPi CD Service Manual...
Chapter 4 Removing and Replacing Parts his chapter provides instructions for removing and replacing field- replaceable components, assemblies, and subassemblies. For removal and replacement procedures for factory-replaceable parts, see Appendix A, “Factory Repair Parts.” Unless otherwise noted, each procedure in this chapter assumes the following: •...
1. Turn off the computer and any attached peripherals. 2. Disconnect the computer and any attached peripherals from AC power 3. Remove the main battery assembly from the battery compartment. Dell Latitude XPi CD Service Manual ecommended Tools Small flat-blade screwdriver Jeweler’s screwdriver set...
battery door Figure 4-2. Main Battery Assembly Removal Part or Assembly Name Main battery assembly 4. To avoid possible damage to the computer from ESD, ground yourself by attaching a wrist grounding strap to yourself and an unpainted metal surface on the I/O panel. If a wrist grounding strap is not available, you can discharge static electric- ity from your body by periodically touching the unpainted metal surface of the I/O panel.
Also, a graphic for that length screw is included in the illustration. Match the actual screw to the graphic in the illustra- tion to check for correct length. Dell Latitude XPi CD Service Manual crew Identification and Tightening A6 (35 mm)
IF Connectors Figure 4-4. Disconnecting an Interface Cable Some of the computer’s interface connectors are zero insertion force (ZIF) con- nectors. These connectors are not removable, but they must be released to disconnect a cable from them. CAUTION: The ZIF connectors are fragile. To avoid damage, do not apply too much pressure to the movable part of the connector.
(which contains the keyboard and the trackball), the display assembly (which contains the LCD), and the bottom case assembly (which contains many of the removable parts). Dell Latitude XPi CD Service Manual ield-Replaceable Parts and Assemblies display assembly trackball assembly...
Some of the instructions are preceded by a table list- ing the Dell order name for the part or assembly being replaced. A more detailed breakdown of parts and assemblies can be found in Appendix A, “Fac- tory Repair Parts.”...
1. Turn the computer upside down on the work surface. 2. To release the memory compartment cover, press down on the identa- Dell Latitude XPi CD Service Manual tion in the edge of the cover, and then slide the cover towards the edge of the computer.
Memory Modules Figure 4-8. Memory Module Removal Part or Assembly Name Memory module, 4-MB Memory module, 8-MB Memory module, 16-MB To remove a memory module, follow these steps: 1. Remove the memory compartment cover. 2. To release a memory module from its socket, gently push outward on each of the memory module’s two metal retaining clips.
1. Remove any installed PC Card(s). 2. Disconnect any cables attached to the audio ports. 3. Remove the hard-disk drive assembly. 4-10 Dell Latitude XPi CD Service Manual almrest Assembly display assembly keyboard CAUTION: Make sure the work surface is clean to prevent scratch- ing the computer cover.
4. Close the display assembly, and turn the computer upside down on a flat work surface. 5. Remove the three palmrest-assembly retaining screws A1, A2, and A3 (see Figure 4-10). A3 (35 mm) 35 mm Figure 4-10. Palmrest-Assembly Retaining Screws 6.
Page 50
A1, A2, and A3 (see Figure 4-10). CAUTION: Be careful not to bend the CD-ROM EMI clip. Set the palm- rest assembly top side down, when the palmrest assembly is free from the bottom case assembly. 4-12 Dell Latitude XPi CD Service Manual...
Trackball Assembly trackball assembly trackball cable Figure 4-11. Trackball Assembly Removal Part or Assembly Name Optical trackball assembly To remove the trackball assembly, follow these steps: 1. Remove the palmrest assembly. 2. Turn the palmrest assembly upside down on a flat work surface. 3.
Keyboard assembly, Japan Keyboard assembly, Korean Keyboard assembly, Latin American KYBD,86,LTN,ALPS,LXPi+ Keyboard assembly, Norwegian Keyboard assembly, Russian Keyboard assembly, Spanish Keyboard assembly, Swedish 4-14 Dell Latitude XPi CD Service Manual press palmrest assembly trackball assembly press keyboard Order Name KYBD,86,BEL,ALPS,LXPi+...
Page 53
Part or Assembly Name Keyboard assembly, Swiss Keyboard assembly, Thailand Keyboard assembly, United Kingdom To remove the keyboard assembly, follow these steps: 1. Remove the palmrest assembly. 2. Press along the sides of the keyboard to release the keyboard from the palmrest assembly.
Tilt-Support Foot Figure 4-13. Tilt-Support Foot Removal Part or Assembly Name Tilt-support foot, left Tilt-support foot, right 4-16 Dell Latitude XPi CD Service Manual isplay Assembly Tilt-support foot Display assembly bezel Display assembly latch and latch spring LCD panel LCD inverter board...
Page 55
To remove a tilt-support foot, follow these steps: 1. Close the display assembly. 2. With the foot set to its fully retracted position, insert a small device (such as a scribe) into the bottom notch on the foot-retaining screw cover and gently lift out the cover partway. Lift on the sides of the cover, working around to the top, and then lift out the cover.
To remove the display assembly, follow these steps: 1. Remove the palmrest assembly. 2. Remove the computer’s tilt-support feet. 3. Remove interface-cable grounding screws C1 and C2 from the 4-18 Dell Latitude XPi CD Service Manual C1 (6 mm) C2 (6 mm) left tilt-support foot connector JLCD 6 mm display assembly.
Page 57
4. Disconnect the display-assembly interface cable from connector JLCD on the system board. To disconnect the cable, grasp the pull tab and pull it straight up from the system board. 5. Disconnect the microphone cable from ZIF connector JMIC. 6. Lift the display assembly from the bottom case assembly. A plastic detent post located approximately at the center of the display assembly may hang on the bottom case assembly.
When replacing the bezel, orient the bezel in its original position on the display assembly and press firmly near each tab until it snaps into position. Be careful to have the display latch and spring properly assembled. 4-20 Dell Latitude XPi CD Service Manual display assembly bezel H2 (10 mm) H1 (10 mm)
Display Assembly Latch and Latch Spring latch spring Figure 4-16. Display Assembly Latch and Latch Spring Removal Part or Assembly Name Display assembly latch Display assembly latch spring To remove the display assembly latch and latch spring, follow these steps: 1.
Figure 4-17. LCD Panel Removal Part or Assembly Name LCD panel LCD assembly, LCD inverter board, active-matrix color, TFT SVGA display 4-22 Dell Latitude XPi CD Service Manual interface cable interface connector LCD inverter board LCD panel LCD power cable connector CN2...
Page 61
To remove the LCD panel, follow these steps: 1. Remove the display assembly bezel. 2. Lift the lower edge of the LCD panel about 1 inch. 3. Disconnect the LCD-assembly power cable from connector CN2 on the LCD inverter board. 4.
5. Lift the LCD inverter board about 6. Disconnect the LCD power cable from connector CN2 on the LCD 7. Lift the LCD inverter board out of the display assembly case. 4-24 Dell Latitude XPi CD Service Manual I1 (5 mm) I2 (5 mm) retaining bracket bracket, and then remove the bracket.
Hinge Covers display assembly base hinge cover hinge Figure 4-19. Hinge Covers Removal Each of the hinge covers is held in place by three tabs that fit into slots on the display assembly base. The microphone is inside the right hinge cover. To remove the hinge covers, follow these steps: 1.
4. Remove the left hinge cover. 5. Remove screws I1 and I2 securing the display-interface cable retaining 6. Disconnect the display-assembly interface cable from ZIF connector 4-26 Dell Latitude XPi CD Service Manual I1 (5 mm) I2 (5 mm) alignment marks...
Page 65
7. Lift the display-assembly interface cable and bobbin out of the display assembly. NOTE: Some computers have a display-assembly interface cable that detaches from the bobbin. If you have a cable with a permanently attached bobbin, stop here; otherwise, proceed to Step 8. 8.
2. Remove the right hinge cover. (Before doing so, note the correct routing 3. Remove the microphone cover from the right hinge cover. 4. Open the microphone cover, and remove the microphone/switch 4-28 Dell Latitude XPi CD Service Manual right hinge cover microphone cover magnet switch of the microphone cable around the display assembly base.)
ottom Case Assembly The bottom case assembly consists of the following: • Diskette/CD-ROM assembly • Deck-buoy • Superpart assembly • System board • 3.1-V power supply board • I/O-panel dust cover • Dust cover for the Advanced Port Replicator • Audio board Removing and Replacing Parts 4-29...
Figure 4-22. Bottom Case Assembly Removal Part or Assembly Name Bottom case assembly 4-30 Dell Latitude XPi CD Service Manual superpart docking EMI clip audio board system board assembly keel plate diskette/CD-ROM assembly I/O bracket clip superpart...
Diskette/CD-ROM Drive Assembly CD-ROM flex cable plastic flip lock connector JCDROM connector JFLOP Figure 4-23. Diskette/CD-ROM Drive Assembly Removal Part or Assembly Name Diskette drive assembly CD-ROM drive assembly To remove the diskette/CD-ROM drive assembly, follow these steps: 1. Remove the palmrest assembly. 2.
Page 70
CD-ROM to the diskette drive. 4-32 Dell Latitude XPi CD Service Manual The front edge of the drive assembly engages tabs on the bottom case assembly. Make sure the diskette drive assembly is clear of the tab before attempting to lift it out of the bottom case assembly.
Deck Buoy B1 (10 mm) Figure 4-24. Deck Buoy Removal Part or Assembly Name Deck buoy To remove the deck buoy, follow these steps: 1. Remove the palmrest assembly. 2. Remove the display assembly. 3. Remove the diskette/CD-ROM assembly. 4. Remove screws B1, B2, and B3. Lift the deck buoy out of the bottom case assembly.
1. Remove the palmrest assembly. 2. Remove the display assembly. 3. Remove the diskette-drive/CD-ROM assembly. 4. Remove the deck-buoy. 4-34 Dell Latitude XPi CD Service Manual B4 (25 mm) thermal tape 25 mm superpart assembly...
Page 73
5. Remove screw B4. Lift the superpart assembly out of the bottom case assembly. CAUTION: To prevent tearing the thermal tape, slowly pull the super- part assembly away from the system board. Removing and Replacing Parts 4-35...
NVRAM. If possible, make a copy of this information before you remove the reserve battery. 4-36 Dell Latitude XPi CD Service Manual superpart docking EMI clip F1 (3 mm) F2 (3 mm)
Page 75
To remove the reserve battery, follow these steps: 1. Remove the palmrest assembly. 2. Remove the superpart assembly. 3. Remove the superpart docking EMI clip and the superpart serial EMI clip. 4. Unplug the battery from connector JRBAT. 5. Place the superpart assembly upside down on a flat work surface. 6.
Part or Assembly Name System board assembly CAUTION: Dell uses the system’s service tag number to maintain a his- tory of the computer and its maintenance services. Do not neglect to transfer the service tag number to the replacement system board assem- bly (see step 3 of “Replacing the System Board Assembly”...
Removing the System Board Assembly To remove the system board assembly, follow these steps: 1. Remove the palmrest assembly. 2. Remove the display assembly. 3. Remove the diskette/CD-ROM assembly. 4. Verify that the PC Card ejectors are fully depressed. 5. Remove the deck buoy plate. (Reinstall this part on the new system board.) CAUTION: To ensure maximum cooling for the microprocessor, do not touch the heat transfer area on the system board above the micro-...
3. Enter the system’s service tag number into the BIOS of the replacement 4-40 Dell Latitude XPi CD Service Manual bracket clip and the side I/O bracket clip are in place. If the side I/O bracket clip has been dislodged, reinstall it as shown in Figure 4-27.
3.1-V Power Supply Board connector JPS1 system board Figure 4-29. 3.1-V Power Supply Board Removal Part or Assembly Name 3.1-V power supply board To remove the 3.1-V power supply board, follow these steps: 1. Remove the palmrest assembly 2. Remove the superpart assembly. 3.
Make sure the dust cover opens and closes freely before you reinstall the display assembly. 4-42 Dell Latitude XPi CD Service Manual pivot pin (2) Push outward on one end of the dust cover to release the pivot pin from its associated pivot hole.
Advanced Port Replicator Connector Dust Cover Figure 4-31. Advanced Port Replicator Connector Dust Cover Part or Assembly Name Advanced Port Replicator connector dust cover To remove the dust cover for the Advanced Port Replicator connector, follow these steps: 1. Remove the palmrest assembly. 2.
3. Remove the superpart assembly. 4. Remove the system board. 5. Remove the hard-disk drive bracket. 6. Lift the audio board straight up from the system board. 4-44 Dell Latitude XPi CD Service Manual audio board audio connectors connector JTB HD1 (6 mm) Turn the system board over and place it on a flat work surface.
Factory Repair Parts his appendix provides procedures for removing and replacing factory com- ponents and subassemblies at a service facility. (Dell does not recommend removal and replacement of factory components and subassemblies in the field. For removal and replacement procedures for field-replaceable parts, see Chap- ter 4, “Removing and Replacing Parts.”)
Power cable, Europe Power cable, Australia Power cable, U.K. Audio board service kit Microphone service kit Reserve battery Dell Latitude XPi CD Service Manual Table A-1. Factory Repair Parts and Assemblies Order Name AC Adapter and Power Cords ADPT,AC,EXT,18V,65W,LXP CORD,PWR,110V,6F,AC...
Page 85
Table A-1. Factory Repair Parts and Assemblies Part or Assembly Name Order Name Batteries Main battery assembly Main battery Technical booklet CD-ROM Drive Assembly CD-ROM drive assembly CD-ROM bezel CD-ROM bezel assembly CD-ROM bezel spring CD-ROM drive CD-ROM drive cable Eject button Screws, diskette/ CD-ROM drive...
Page 86
Keyboard assembly, Danish Keyboard assembly, French * Substitute your drive capacity for xxxxx, your drive height for yy, and the Dell Latitude XPi CD Service Manual Table A-1. Factory Repair Parts and Assemblies Order Name Diskette Drive Assembly SUBASSY,FD/CD,LXPiCD...
Page 87
Table A-1. Factory Repair Parts and Assemblies Part or Assembly Name Order Name Keyboards Keyboard assembly, French/Canadian Keyboard assembly, German Keyboard assembly, Japan Keyboard assembly, Korean Keyboard assembly, Latin Keyboard assembly, Norwegian Keyboard assembly, Russian Keyboard assembly, Spanish Keyboard assembly, Swedish Keyboard assembly, Swiss Keyboard assembly,...
Page 88
Display assembly case, 12.1-inch Display assembly latch ser- vice kit, 12.1-inch Display assembly latch, 12.1-inch Display-assembly latch spring, 12.1-inch Dell Latitude XPi CD Service Manual Table A-1. Factory Repair Parts and Assemblies Order Name LCD Assemblies SVC,CBLS,LCD,TFT,SAM- SUNG,LXPi+CD Display-assembly CBL,FPC,LED/INVRTR,TFT, interface cable 12.1”...
Page 89
Table A-1. Factory Repair Parts and Assemblies Part or Assembly Name Order Name LCD Parts Hinge cover, right Hinge cover, left Display assembly base Left hinge Right hinge Display-assembly-bezel re- taining screw covers, lower Display-assembly-bezel re- taining screw covers, upper Display-assembly EMI shield 12.1-inch Memory...
Page 90
Tilt-support foot, right I/O panel dust cover Main battery insulator I/O bracket, hinge Superpart assembly Spreader plate Spreader plate spacer Dell Latitude XPi CD Service Manual Table A-1. Factory Repair Parts and Assemblies Order Name Miscellaneous Parts CLP,EMI,CD,LXPiCD CLP,EMI,KYBD,LXPiCD CLP,EMI,SER,SUPERPRT,...
Page 91
Table A-1. Factory Repair Parts and Assemblies Part or Assembly Name Order Name Miscellaneous Parts Keel plate Deck buoy Microphone insulator bracket Bottom case assembly Power button Power-button mounting bracket Memory compartment cover Palmrest Assembly Palmrest service kit Palmrest assembly Technical booklet Screws Screws service kit...
Page 92
10 mm, gold 10 mm, black 10 mm, black 25 mm, black System board assembly, LXPi CD, 150-MHz, service kit A-10 Dell Latitude XPi CD Service Manual Table A-1. Factory Repair Parts and Assemblies Order Name Screws (Continued) SCR,2mmX6mm,PHH,MS, BLO,LXP B6 SCR,2.6mmX8mm,PHH,MS, SCR,2.5mmX10mm,PHH,MS,...
Page 93
Table A-1. Factory Repair Parts and Assemblies Part or Assembly Name Order Name System Board Assemblies System board, 150-MHz I/O interface cable Bracket, I/O Serial EMI clip, I/O Docking EMI clip, I/O Diskette, field service Technical booklet, service Trackball Optical trackball assembly Trackball interface cable Trackball...
ard-Disk Drive The hard-disk drive resides in a carrier that mounts inside the computer’s hard-disk drive bay. Four screws secure the drive inside the carrier. A mylar insulator provides electrical insulation between the hard-disk drive and the bot- tom of its carrier. To remove the hard-disk drive and hard-disk drive insulator, follow these steps: 1.
Palmrest Brace Remove screws A-7 through A-9 (see Figure A-2). Gently pull the brace toward the front, and lift the brace away from the palmrest. A-16 Dell Latitude XPi CD Service Manual D-ROM Drive iskette Drive almrest Assembly Components...
isplay Assembly Components The display assembly consists of the LCD assembly and its related components. It also contains the LED board, which provides visual indications of many of the computer’s basic functions. The microphone assembly is mounted inside the right hinge cover of the display. Some parts of the display assembly can be removed and replaced without removing the assembly from the computer.
7. Lift the display assembly base away from the left hinge. 8. Disengage the display-assembly interface cable from the slot in the A-18 Dell Latitude XPi CD Service Manual See “LCD-Inverter-Board Interface Cable” in Chapter 4. See “Display Assembly Base” later in this chapter.
Display Assembly Hinges To remove a hinge (see Figure 4-14), follow these steps: 1. Remove the display assembly from the computer. See “Display Assembly” in Chapter 4. 2. Remove the display assembly bezel. See “Display Assembly Bezel” in Chapter 4. 3.
Figure A-5. System Board Assembly in the Bottom Case Assembly To remove a part of the system board assembly, Dell recommends that you first remove the assembly as described in “System Board Assembly” in Chapter 4. Then follow the instructions described in the following subsections to remove parts of the system board assembly.
Keyboard/Keypad/Mouse Connector Shield connector shield D4 (3 mm) Figure A-6. Keyboard/Keypad/Mouse Connector Shield Removal Two tabs on the keyboard/keypad/mouse connector shield engage two associ- ated slots on the I/O panel near the keyboard/keypad/mouse connector. Retaining screw D4 attaches the bottom of the shield to the bottom of the I/O panel.
To remove the cable, follow these steps: 1. Disconnect one end of the I/O interface cable from connector JSTDIO 2. Disconnect the other end of the I/O interface cable from connector A-22 Dell Latitude XPi CD Service Manual system board connector JSTDIO on the system board.
I/O Board I/O board I/O bracket clip I/O bracket Figure A-8. I/O Board Removal To remove and replace the I/O board, follow these steps: 1. Remove the I/O interface cable from connector JSTDIO. See the previous subsection in this appendix. 2.
2. Remove the standoff nuts ST1 through ST8 3. Remove screw D5. 4. Remove the I/O bracket from the system board. A-24 Dell Latitude XPi CD Service Manual ST8 (4 mm) 4 mm 3 mm See the previous subsection in this appendix.
ottom-Case Assembly Components power button Figure A-10. Bottom-Case Assembly Components To remove parts of the bottom case assembly, you must first remove the system board assembly as described in “System Board Assembly” in Chapter 4. The subsections that follow describe the removal and replacement of bottom-case assembly components.
Lift the mounting bracket out of the bottom case assembly; then press the power button out of the hole in the side of the bottom case assembly. A-26 Dell Latitude XPi CD Service Manual power button power button mounting bracket...
Spreader and Keel Plates spreader plate keel plate bottom case assembly Figure A-12. Spreader and Keel Plate Removal Remove the spreader plate by lifting it from the bottom case assembly. The spreader plate fits easily over plastic projections and screw holes. The keel plate is in the center of the bottom case, below the spreader plate.
Page 110
A-28 Dell Latitude XPi CD Service Manual...
Dell Accessories program group in Windows. Each button in the Dell Control Center window corresponds to a particular group of system setup options. The Dell Control Center has a detailed help file that explains each setup option. Figure B-2. Dell Control Center Window...
System Setup program and then activates suspend mode. To enter the System Setup program, hold down the <CTRL> and <ALT> keys and press the <ENTER> key, or press the <FN> and <F1> keys. Dell Latitude XPi CD Service Manual...
UPPER PC CARD SOCKET LOWER PC CARD SOCKET MONITOR TOGGLE Dell Latitude XPi CD Service Manual Table B-1. System Setup Program Categories Function Displays the version number and release date of the BIOS in the computer. Resets time on computer’s internal clock.
Page 115
Displays amount of video memory. EXTERNAL CACHE Displays amount of external cache memory. EXPANSION DEVICE Shows the type of Dell Latitude Advanced Port Replicator that is attached to the com- puter. There are no user-selectable settings for this option. SERVICE TAG Displays computer’s five-character service...
Page 116
RING/EVENT RESUME ALARM RESUME DISPLAY CLOSE SYSTEM SWITCH BATTERY STATUS Dell Latitude XPi CD Service Manual Table B-1. System Setup Program Categories Function Determines how long computer operates with- out detecting I/O activity before display is switched off to conserve battery power. This option should be disabled if software compati- bility problems occur.
Page 117
Table B-1. System Setup Program Categories Category Function INTELLISPIN Compensates for unbalanced CDs that cause the computer to vibrate when the CD-ROM drive is in use. Allows use of discs that might otherwise be unreadable. Available for CD-ROM drives with speeds of 6X or higher. MANCE run at the highest speed.