Page 1 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936...
Page 2: Safety Information
Therefore, the following checks should be performed for the continued protection of the customer and servicetechnician. PDP-6010FD...
Page 3 PRODUCT SAFETY NOTICE With the AC plug removed from an AC power source, place a Many electrical and mechanical parts in PIONEER set have jumper across the two plug prongs. Turn the AC power switch on. special safety related characteristics. These are often not evident...
Page 4 To protect products from damages or failures during transit, the shipping mode should be set or the shipping screws should be installed before shipment. Please be sure to follow this method especially if it is specified in this manual. PDP-6010FD...
Page 5: Table Of Contents
5.5.2 FUNCTION OF DECREASING THE BRIGHTNESS LEVEL ................. 73 5.6 OUTLINE OF THE OPERATION ..........................74 5.6.1 PANEL DRIVE-POWER ON / OFF FUNCTION ..................... 74 5.6.2 SPECIFICATION OF THE FAN CONTROL......................75 5.6.3 PROCESSING IN ABNORMALITY ........................76 5.6.4 TRAP SWITCH............................... 79 PDP-6010FD...
Page 6 10.4 CHASSIS SECTION (1/3) ............................172 10.5 CHASSIS SECTION (2/3) ............................174 10.6 CHASSIS SECTION (3/3) ............................176 10.7 PANEL CHASSIS SECTION .............................178 10.8 MULTI BASE SECTION ............................180 10.9 PDP SERVICE ASSY 608F (AWU1274)........................182 10.10 SPEAKER SYSTEM (PACKING) ..........................185 10.11 CS ASSY ................................186 PDP-6010FD...
Page 7: Service Precautions
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting temperatures (hard to melt/easy to harden). The following lead-free solders are available as service parts: • Parts numbers of lead-free solder: GYP1006 1.0 in dia. GYP1007 0.6 in dia. GYP1008 0.3 in dia. PDP-6010FD...
Page 8: Charged Section And High Voltage Generating Point
: Part is Charged Section. : Part is the High Voltage Generating Points other than the Charged Section. 60F Y DRIVE Assy POWER SUPPLY Unit 60F X DRIVE Assy Conductive plate X AC inlet Power switch Fig. High Voltage Generating Point (Rear view) PDP-6010FD...
Page 9: Specifications
(AXD1550) (ADG1215) Terminal Position Sheet (AAX3504) (for use when mounting the plasma display on the wall) Alkaline dry cell battery (LR6, AA) Binder Assy (AEC1908) Speed clamp: ×3 Bead band: ×3 Cleaning cloth (AED1285) Warranty card Operating instructions (ARE1472) PDP-6010FD...
Page 10 (M5 × 10 mm: black) (SBA1269) Screw 2 : ×4 Screw 3 : ×4 (M6 × 20 mm: black) (for plastic bands) (M4 × 10 mm: black) Hexagonal wrench : ×1 (Opposite side 4 mm for M5 use) (SEX1028) PDP-6010FD...
Page 11: Specifications
2.2 SPECIFICATIONS Item 60” plasma display model: PDP-6010FD Number of pixel 1920 × 1080 pixels 17 W + 17 W (1 kHz, 10 %, 6 Ω) Audio Amplifier Speakers Woofer: 4.8 cm x 13 cm cone type Tweeter: 2.5 cm semidome type...
Page 12: Panel Facilities
14 INPUT 3 terminals (COMPONENT VIDEO: Y, P 5 Room Light Sensor 6 Remote control sensor 15 INPUT 3 terminal (VIDEO) 16 INPUT 3 terminals (AUDIO) 7 STANDBY/ON button The buttons with asterisks (*) can operate the TV Guide On Screen™ system. PDP-6010FD...
Page 13 11 RS-232C terminal (used for factory setup) 26 SPEAKERS (R) terminal (Speaker side) 12 ANT B IN terminal 27 SPEAKERS (L) terminal (Speaker side) 13 INPUT 1 terminal (S-VIDEO) 14 INPUT 1 terminal (VIDEO) 15 SUB WOOFER terminal 16 AUDIO OUT terminals (AUDIO) PDP-6010FD...
Page 14 All buttons on the remote control unit are luminous and gather and store light. This enables quick access to the desired function when performing operations in dark places. Mode switch (with “TV” selected) Note • When using the remote control unit, point it at the plasma display. PDP-6010FD...
Page 15: Basic Items For Service
Item to be checked regarding video Item to be checked regarding audio Block noise Distortion Horizontal noise Noise Dot noise Volume too low Disturbed image (video jumpiness) Volume too high Too dark Volume fluctuating Too bright Sound interrupted Mottled color PDP-6010FD...
Page 16: Quick Reference
[j] seven times.) 2 Press [l] to select "CLEAR". Hold [ENTER/SET] pressed for at least 5 seconds. 2. Press [ENTER/SET], then select a Mask indication, using [i] or [j]. After clearance is completed, "ETC" is automatically selected. PDP-6010FD...
Page 17 50. PTN MASK 49 11. COMBI MASK SETUP (+) 1. MASK OFF 2. CMB MASK 01 For use while Combination Mask is displayed. • • • • • Use [i] or [j] to select the type of mask. 18. CMB MASK 17 PDP-6010FD...
Page 18: Pcb Location
IC3101 - IC3104 SN755871PZT-P FHD POWER SW ASSY AWW1293 60F X DRIVE ASSY AWV2505 POD ASSY AWW1295 60F Y DRIVE ASSY AWV2506 > PANEL SENSOR ASSY AWW1309 POWER SUPPLY UNIT AXY1169 60F DIGITAL ASSY AWW1308 PDP SERVICE ASSY 608F AWU1274 PDP-6010FD...
Page 19: Jigs List
Name Jig No. Remarks Service Cotton Cloth Glove GYX1002 7.3 DISASSEMBLY AND REASSEMBLY PRECAUTIONS FOR SPEAKER SYSTEM 3.5 CLEANING Name Part No. Remarks Cleaning liquid GEM1004 Used to fan cleaning. Refer to “10.5 CHASSIS SECTION (2/3)”. Cleaning paper GED-008 PDP-6010FD...
Page 20: Block Diagram
4. BLOCK DIAGRAM 4.1 OVERALL WIRING DIAGRAM (1/2) PDP-6010FD...
Page 21 When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST". mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. PDP-6010FD...
Page 22: Overall Wiring Diagram (2/2)
4.2 OVERALL WIRING DIAGRAM (2/2) V+8V_AU V+3_3V_AU_A V+3_3V_AU_D PDP-6010FD...
Page 23 PDP-6010FD...
Page 24: Overall Block Diagram (1/2)
CLK / LE / HBLK / LBLK R/G/B R/G/B DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1681 IC1671 IC1661 IC1651 IC1871 IC1861 IC1851 60F ADDRESS L ASSY 60F ADDRESS S ASSY A B C PDP-6010FD...
Page 25 CLK / LE / HBLK / LBLK R/G/B R/G/B DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC DRIVER IC IC1681 IC1671 IC1661 IC1651 IC1681 IC1671 IC1661 IC1651 60F ADDRESS L ASSY 60F ADDRESS L ASSY PDP-6010FD...
Page 26: Overall Block Diagram (2/2)
SCL_AV I2S_BCLK_DTV I2S_LRCLK_DTV I2S_SDATA_DTV SPDIF_DTV I2S_BCLK_HDMI I2S_LRCLK_HDMI I2S_SDATA_HDMI SPDIF_HDMI TXD_SR+ RXD_SR+ SR_OUT IC8301 TXD/RXD AGC1037- RS232C 232C_DET (IF UCOM) IC9201 TAS5122DCA-TBB (D-AMP) IC7001 FHD IR ASSY TC90173FG KEY_AD1/AD2 IC6301 IC6401 SIDE KEY ASSY BCM3517 BCM7038 POD Card POD ASSY PDP-6010FD...
Page 27 IC4303 A0 to 19 PQ200WNA1ZPH PQ200WNA1ZPH DQ0 to 15 (FAN CONTROL) (FAN CONTROL) IC8402 AGC1039- Input 4 Input 5 Input 6 Input 7 (FLASH) HDMI HDMI HDMI HDMI TRAP SW FHD FAN TRAP SW CONNECT ASSY 42/60 LED ASSY PDP-6010FD...
Page 28: Power Supply Unit
4.5 POWER SUPPLY UNIT POWER SUPPLY UNIT PDP-6010FD...
Page 29: X Drive Assy
Drive Signal Gate Signal +16.5 PreDrive +16.5V SOFT-D Drive Signal PSUS RESONANCE LOGIC BLOCK BLOCK +16.5 Drive Signal OFFSET BLOCK VSUS PSUS VPOFS VPOFS VXKOFS1 VXKOFS2 OFFSET BLOCK Reg. DC/DC +16.5V CONV. VSUS BLOCK +60V +8V +3.3V +60V +8V +3.3V PDP-6010FD...
Page 30: Y Drive, 60F Scan A, B, C And D Assys
BLOCK IC5V/VF VH IC5V DC/DC DC/DC BLOCK IC5V CONV. Scan IC CONV. IC3103 +3.3V VADR VH IC5V Photo Coupler Scan Signal BLOCK Scan IC IC3102 IC5V Scan IC IC3101 60F SCAN D ASSY (LOW-SIDE_LOW) 60F SCAN C ASSY (LOW-SIDE_HIGH) PDP-6010FD...
Page 31: Power Supply Block Of 60F X, Y Drive And 60F Scan A, B, C And D Assys
Note: VYPRST, VSNOFS, VYKOFS12, VYKOFS3, VYKOFS4 YKOFS VYKOFS drive VXKOFS1 and VXKOFS2 voltages are electrical volume controls. Reg. YKOFS VYKOFS drive Reg. RST-D drive SOFT-G drive Scan Logic IC5V Scan IC 60F SCAN A, B, C, D ASSYS PDP-6010FD...
Page 32: Address L And S Assys
DRIVER IC DRIVER IC IC1851 IC1861 IC1871 CLK / LE / HBLK / LBLK R/G/B VADR1 VDDLS1 VADR2 VDDLS2 VADR3 VDDLS3 RESONANCE RESONANCE RESONANCE BLOCK BLOCK BLOCK IC1801 LVDS Receiver V+60V V+3.3V AN/P BN/P CN/P DN/P CLKN/P CN1801 CN1802 PDP-6010FD...
Page 33: Digital Assy
RST_SQ IC3601 PSIZE V+1_2V_D V+3_3V_D LVDS TRANSMITTER PEG384B IC3401 LVDS LVDS V+1_1V_D V+1_8V_D V+3_3V_D Flash Memory SUB-FILD CONV. XSUS IC3302 & RESETX XY DRV SEQUENCE UART PATTERN GEN. PEG383B-K IC3301 LVDS LVDS Reciever Reciever IC3201 IC3202 INP_MUTE V+3VACTV LVDS PDP-6010FD...
Page 34: Main Assy (Dtv Block Diagram)
BCM3517 KQLGB0-K SPDIF out I2S out [IC6301] HSX_0 I2C0 SDRAM [IC6602] 256Mbit [12bit] 1Chip System IC To ARIA SDRAM BCM7038KPB1G-B2-K [IC6603] [IC6401] 256 Mbit YUV(656) [8bit] From VDEC SDRAM [IC6604] 256Mbit SDRAM [IC6605] 256 Mbit UARTA VBI_Y From AV_SW PDP-6010FD...
Page 35 PDP-6010FD...
Page 36: Power Supply Block Of Main Assy
LTC 3407 IC4501 IC4401 DD com. 3.3V-REG for EMMA (V+2_5V_UCOM) (V+3_3V_A) V+2_5V_UCOM V+3_3V_A_ADC LTC3407-2 NJM2846DL3-33 V+2_5V_UCOM_DDR Q4416 FET Switch IC4501 (V+3_3V_A_VDEC) V+3_3V_A_VDEC DD com. RTQ040P02 for EMMA (V+1_5V_UCOM) V+1_5V_UCOM LTC3407-1 IC4404 DD com. for 7038, 3517 (V+1_2V_D) V+1_2V_D_7038 LTC3416 V+1_2V_D_3517 PDP-6010FD...
Page 37 FET Switch (V+2_5V_D) V+2_5V_D_7038 (V+1_8V_A_VDEC) V+1_8V_A_VDEC BD8602FV-3/ MCH3406 SP8M4 V+2_5V_D_7038_DDR V+2_5V_D_3517 Q4411 FET Switch (V+2_5V_D2) V+2_5V_D2_ARIA RSS100N03 V+2_5V_D2_ARIA_DDR Q4514 FET Switch (V+3_3V_D2) V+2_5V_UCOM_VBI RTQ040P02 IC4403 IC4106 3ch DD com. 1.5V-REG for ARIA V+1_2V_D2_ARIA (V+1_2V_D2) (V+1_5V_VDEC) V+1_5V_UCOM_VBI BD8602FV-3/ NJM2886DL3-15 RSS100N03 RSS090P03 PDP-6010FD...
Page 38: Tanshi Assy
INPUT1 INPUT(VIDEO) for MAIN ASSY INPUT2 INPUT3 INPUT4 INPUT5 PC AUDIO SCL_AV INPUT3(YPbPr) DETECT SDA_AV for SIDE IO ASSY BLOCK RST_MSP SPDIF_DTV I2S_DTV INPUT3(AUDIO,CVBS) SPDIF_HDMI for SIDE IO ASSY A_NG_B for MAIN ASSY R OUT L OUT SP TERMINAL PDP-6010FD...
Page 39: 42/60 Led And Fhd Ir Assys
4.14 42/60 LED and FHD IR ASSYS PDP-6010FD...
Page 40: Power Supply Block Of Fhd Rls And Side Key Assys
4.15 POWER SUPPLY BLOCK of FHD RLS and SIDE KEY ASSYS FHD RLS ASSY OP AMP V+3_3V_UCOM IC9781 MM3012XN IC9782 AMS114YD01 SIDE KEY ASSY V+3_3V_STB S9501 to S9507 PDP-6010FD...
Page 41: Diagnosis
500 mS 500 mS normally. Orange Blue Downloading of DTV Module software is abnormally finished. Orange 500 mS 500 mS 500 mS 500 mS 500 mS 500 mS 500 mS Blue Always lighting Always lighting Trap switch Orange Lightins out PDP-6010FD...
Page 42: Power On Sequence
2 : The IF microcomputer sends the operation data of the remote control unit (or KEY) to the main microcomputer. 3 : The main microcomputer issues a startup command (PON) to the MOD microcomputer. 4 : The relay is controlled with logical OR interpretation of control signals by the main microcomputer and module (MOD) microcomputer. PDP-6010FD...
Page 43: Details Of Power On Sequence
Scan DRIVE DCDC/REG DRIVE/SCAN Sensor The user operation with the remote control unit is invalid. (All LED: OFF) Standby power device and some Vcc power devices operate. RGB-SW/AD/D-AMP/MAP are electrified, but uses the power-saving mode function of the IC. PDP-6010FD...
Page 44 Module_ EEPROM V+6.5V ucom V+5.1V Vsus Vadr Digital DRF_B VSUS VADR X/Y Drive Address BAK_EEP ASIC ADDRESS Scan DRIVE DCDC/REG DRIVE/SCAN Sensor A state when it displays a picture on the PDP. (Blue LED: ON) All devices are electrified. PDP-6010FD...
Page 45: Diagnosis Flowchart Of Failure Analysis
Is there any local abnormality Is the abnormality associated Replace the panel chassis. with a single scan line? on the screen? with one ADDRESS or one TCP? Failure analysis for the Failure analysis for the drive system => DR3 drive system => DR4 PDP-6010FD...
Page 46 Is an external video signal MAIN Assy => MA3 displayed properly? Problems concerning the audio output No Failure analysis for the Is the audio signal output? audio system => AU1 Specific failure whose cause is difficult to identify in the initial stage PDP-6010FD...
Page 47: Power Supply Unit
Replace the POWER SUPPLY 205 and 215 V (VSU: 125/35°C). specified range? Unit. The ripple must be within 10 V. Replace the POWER SUPPLY Is there a fluctuation in the Unit. VSUS voltage? The POWER SUPPLY Unit is normal. PDP-6010FD...
Page 48: Drive Assy
Properly connect the panel FPC Replace the FFC cables. Is the input signal normal? connectors properly connected to and SCAN Assys connectors. the X/Y DRIVE Assys? Replace the panel chassis. Replace the X/Y DRIVE Assys. Replace the DIGITAL Assy. PDP-6010FD...
Page 49 Is the input signal normal? Replace the FFC cables. (See the oscilloscope photos.) Replace the DIGITAL Assy. Is the waveform of the control signal from the SCAN Assy normal? Replace the Y DRIVE Assy. (See the oscilloscope photos.) Replace the SCAN IC. PDP-6010FD...
Page 50 Are all the connectors properly Reconnect the connectors. connected? Is the TCP control signal normal? Is the input signal normal? (See the oscilloscope photos.) (See the oscilloscope photos.) Replace the panel chassis. Replace the FFC cables. Replace the DIGITAL Assy. PDP-6010FD...
Page 51 Is the waveform of the SCAN IC Replace the Y DRIVE Assy. control signal from the Y DRIVE Assy normal? Replace the SCAN IC. Replace the panel chassis. PDP-6010FD...
Page 52: Digital Assy
Replace the MAIN Assy. Replace the MAIN Assy. Is the indication position correct? It is most likely that the sync signal is abnormal. Is the tone correct? It is most likely that the video signal data are missing. Replace the MAIN Assy. PDP-6010FD...
Page 53: Main Assy
SIDE KEY and MAIN Assys. Can the unit be turned on, using Replace the MAIN Assy. Replace the MAIN Assy. RS-232C commands? Failure in the RS-232C driver and its peripheral circuits Failure in the Main microcomputer. Replace the MAIN Assy. PDP-6010FD...
Page 54: Video System
Is the sync signal input to IC8001? Replace the MAIN Assy. Replace the MAIN Assy. Replace the MAIN Assy. Is the selected input signal a => USB_E / USB_R USB signal? No problem with the MAIN Assy PDP-6010FD...
Page 55 IC4801 - pin 22 (S-video) IC4801 - pin 26 (S-video) V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div PDP-6010FD...
Page 56 IC4801 - pin 22 (S-video) IC4801 - pin 26 (S-video) V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div PDP-6010FD...
Page 57 IC5001 - pin 48 (PC) IC5001 - pin 54 (component) IC5001 - pin 54 (PC) V: 500 mV/div H: 10 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div PDP-6010FD...
Page 58 IC5001 - pin 54 (component) IC5001 - pin 54 (PC) V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 10 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div V: 500 mV/div H: 20 μsec/div PDP-6010FD...
Page 59 Is the signal from IC6401 to Check between IC6401 and IC8001? IC8001. If there is no problem then replace IC6401. Has the symptom been settled The panel is defective. when the MAIN Assy is replaced? Replace the MAIN Assy. PDP-6010FD...
Page 60: Audio System
(pins 2, 3, 5, 6) microcomputer and clock output of X9101. 49 50 If there was no ploblem replace the MAP5601M. Are signals output from IC9151? Check the IC9151 and peripheral circuit. (pins 1, 7) Repair the failure points. PDP-6010FD...
Page 61 V: 2 V/div H: 1 mS/div V: 2 V/div H: 1 mS/div V: 2 V/div H: 1 mS/div IC9101 - pins 38, 39 IC8871 - pins 1, 7 V: 1 V/div H: 1 mS/div V: 1 V/div H: 1 mS/div PDP-6010FD...
Page 62 IC5201 - pin 78 IC9101 - pin 106 IC9101 - pin 107 IC9101 - pin 108 V: 1 V/div H: 1 μS/div V: 1 V/div H: 10 μS/div V: 1 V/div H: 10 μS/div V: 1 V/div H: 10 μS/div PDP-6010FD...
Page 63: Diagnosis Of Pd (Power-Down)
5.3 DIAGNOSIS OF PD (POWER-DOWN) 5.3.1 BLOCK DIAGRAM OF THE POWER-DOWN SIGNAL Block Diagram of the Power-Down Signal PDP-6010FD...
Page 64: Pd (Power-Down) Diagnosis Of Failure Analysis
EXT_PD line: Open CN3801 disconnection detection UNKNOW DIGITAL Assy It becomes "UNKNOW" except ModuleUcom can not Each PD line of ModuleUcom above-mentioned PD detection detection condition. UVP: Under Voltage Protection , OVP: Over Voltage Protection , OCP: Over Current Protection PDP-6010FD...
Page 65 Y DRIVE Assy SCAN A, B, C, D 4 (SCN-5V) CN2801, CN2902 Assy SCAN A, B, C, D Assy CN3002, CN3101 CN1602, CN1802 DIGITAL Assy 8 (ADRS) ADDRESS Assy CN1601, CN1801 X DRIVE Assy, 8 (ADRS) Y DRIVE Assy PDP-6010FD...
Page 66 IC5V SCN5V_PD voltage detection DCDC converter drive stop SCAN Hi Unconnect SCAN Low Unconnect YDRV_PD disconnection detection Decrease voltage 15VDD detection VNOFS VKOFS1_2 Decrease voltage YDD_PD detection VKOFS3 VKOFS4 Decrease voltage VPRST detection Increase or decrease SCAN_PD voltage detection PDP-6010FD...
Page 67: Diagnosis Of Sd (Shutdown)
5.4 DIAGNOSIS OF SD (SHUTDOWN) 5.4.1 BLOCK DIAGRAM OF THE SHUTDOWN SIGNAL Block Diagram of the Shutdown Signal PDP-6010FD...
Page 68: Sd (Shutdown) Diagnosis
5.4.2 SD (SHUTDOWN) DIAGNOSIS PDP-6010FD...
Page 69 PDP-6010FD...
Page 70: Non-Failure Information
In a case of color difference 4:2:2, Y, Cb, and Cr use 12 bits each, but Cb and Cr are transmitted at a half sampling rate of Y. This unit is capable of processing the upper 10 bits out of 12 bits of video data. Recent high-end DVD players, such as Pioneer DV-79AVi, are capable of outputting 10-bit color-difference signals.
Page 71 " Confirmation of the manufacturer of the connected equipment Check if the connected equipment was manufactured by Pioneer and if it supports the HDMI Control function. If its manufacturer is not Pioneer, proper operations are not guaranteed.
Page 72 • "Power On Test" or "Power Off Test" cannot be selected (the items are grayed) • The connected device cannot be turned on/off. In some cases, an operation check using another HDMI input connector may be required in order to narrow down the cause. PDP-6010FD...
Page 73: Function Of Decreasing The Brightness Level
Detection example: Protection against panel cracking 80 °C. High-temperature protection function 2 The count of plasma discharge with regard to the APL will be decreased if the panel temperature becomes 55 °C or higher. APL (average picture level) PDP-6010FD...
Page 74: Outline Of The Operation
(The panel drive-power OFF state remains in effect even if the main power switch is set to OFF after that command is sent.) When the panel drive-power is ON When the panel drive-power is OFF POWER SUPPLY Unit POWER SUPPLY Unit DRF-SW-B DRF-SW-B (TEST PIN) (TEST PIN) Alligator clip Multi base Multi base PDP-6010FD...
Page 75: Specification Of The Fan Control
• When the temperature rises, the sensor voltage of TEMP2 decreases. • When the voltage of the DAC output for external FAN decreases, rotation speed of FAN rises. PDP-6010FD...
Page 76: Processing In Abnormality
When the panel is off: A warning indication is not displayed immediately but is displayed when the panel is turned on. Note: A warning indication is displayed each time the panel is turned on if the conditions for a shutdown persist. Conditions for resetting the circuits The circuits will be reset upon Standby ON/OFF. PDP-6010FD...
Page 77 A specific LED flash pattern (blue LED, 13 times) starts. The next PON operation is valid, and the flag is cleared upon the next power-on. If RST4 is H, a restoration process starts according to the latest power-on/-off status. PDP-6010FD...
Page 78 UART. Upon receiving the data, the main microcomputer orders a specific LED flash pattern (blue LED, 4 times). The next PON operation is valid, and the flag is cleared upon the next power-on. PDP-6010FD...
Page 79: Trap Switch
(1) Deactivating with the remote control unit • Enter Factory mode. • Proceed to the INITIALIZE layer of Factory mode. Hold the DISPLAY key pressed for more than 5 seconds. (2) Deactivating with the RS-232C command • Send the CTM (cancel) command. PDP-6010FD...
Page 80: Service Factory Mode
How to exit Service Factory Mode By using a PDP service remote control) • PDP service remote control : press [FACTORY] key. • Supplied remote control unit : press [HOME MENU] key. By issuing RS-232C commands) • Issue [FAN]. PDP-6010FD...
Page 81: Functions When Entering The Service Factory Mode
(HDMI settings, etc.). • Data on screen (i.e., screen position; meaning clock dividers, and not including data on screen size). Are reset to the default values (data stored in memory will be retained). Screen size will be retained. PDP-6010FD...
Page 82: Remote Control Code In Service Factory Mode
(Note 1) When ten seconds have passed since the [DRIVE OFF] key was pressed at the standby, it becomes invalid. Please press [POWER] key from the [DRIVE OFF] key pressing within ten seconds when you do power supply ON while driven OFF. PDP service PRO-1150HD PDP-6010FD remote control PRO-950HD PDP-6010FD...
Page 83: Pdp Service Remote Control
Press this key to turn on the unit. This key cannot turn the unit off. POWER OFF Press this key to turn off the unit. This key cannot turn the unit on. POINT ZOOM Not used with this model. ZOOM +/- Not used with this model. PDP-6010FD...
Page 84: Factory Hierarchical Table
ADDRESS U3 <=> PH0 to PH9 Equivalent to AP3S*- (Setting value: PH2) ADDRESS U4 <=> PH0 to PH9 Equivalent to AP3S-* (Setting value: PH0) STK MODE <=> OFF <=> MODE1 to MODE8 <=> SKM S00 to S07 *: Setting value PDP-6010FD...
Page 85 6.2.4.1 SIDE MASK LEVEL (+) SIDE MASK LEVEL <=> 6.2.4.2 FINAL SETUP DATA RESET <=> NO <=> YES 6.2.4.3 HMG/HG SERVICE MODE MODE SHIFT <=> NO <=> YES Exclusively used for 6.2.4.4 Wide XGA AUTO <=> technical analysis DISABLE <=> ENABLE (details omitted) PDP-6010FD...
Page 86: Indications In Service Factory Mode
2 SIG mode and Screen size Note: See SIG-Mode Tables. (See next page.) 3 Color system and Signal type Color System and Signal Type NTSC Composite input S-connector input Y/CB/CR Y/PB/PR Digital Video signal Option (Destination, Panel Generation, etc.) Options Regular model ELITE model PDP-6010FD...
Page 87 Current selection of the screen size 5th Character GUI Notation VIDEO Remarks k (∗) − DOT BY DOT FULL − ZOOM − CINEMA − WIDE k: supported, −: unsupported Note (∗): It is effective only with models having the Full HD panel. PDP-6010FD...
Page 88: Details Of Factory Menu
In the 19-24 rows, the version of the execution program is displayed. • PANEL INFO: It displays the generation of the panel, inchage and the type of the panel. For details on display values and settings, see "10: Panel Information" in "9.3.1. QS1 (PANEL STATUS)." PDP-6010FD...
Page 89 0 6 0 – D I G – R S I 0 1 2 3 4 5 6 7 O R D 1 2 3 4 Display Example Meaning Item Name HMG/HG module Version HMG/HG 01234567 User Password PASSWORD 1234 PDP-6010FD...
Page 90 Abnormally in RST2 of MAIN Assy. (power decrease of DC-DC converter) RELAY Abnormally in RST4 of MAIN Assy. (power decrease of Relay power) Failure at Home Media Gallery Home Media Gallery startup error MA-EEP IIC communication line between EEPROM and MAIN. PDP-6010FD...
Page 91 Even if [k] key or [l] key is pressed, {CLEAR <=> :YES} ⇔ {CLEAR <=> :NO} is repeated. If the [ENTER/SET] key is kept on pressing for 5 second when the status of this menu is <YES>, clear process will begin. PDP-6010FD...
Page 92 B-SENSOR : The value that indicated the degree of brightness input into an Room light sensor is displayed. AD value when the output of the Room light sensor was input into 89 pin (AN5) of IF uCOM is displayed. PDP-6010FD...
Page 93 Even if [k] key or [l] key is pressed, {CLEAR <=> :YES} ⇔ {CLEAR <=> :NO} is repeated. If the [ENTER/SET] key is kept on pressing for 5 second when the status of this menu is <YES>, clear process will begin. MTB HOUR METER is cleared only. PANEL HOUR METER is not cleared. PDP-6010FD...
Page 94 HDMI mode status ---- BIST NVAL N value CTSVAL CTS value AKSV Shadow AKSV value BKSV Shadow BKSV value IT CNT IT content (AVI info) EXTCOL Extension calorimetry (AVI info) RGV QR RGB range (AVI info) PIXDEP Number of pixel/bit PDP-6010FD...
Page 95 2200 562 or 563 1920 1920x1080i @ 60 720p (750p) @ 60 1650 1280 1280x720p @ 60 1080p (1125p) @ 60 2200 1125 1920 1080 1920x1080p @ 60 1080p (1125p) @ 24 2750 1125 1920 1080 1920x1080p @ 24 PDP-6010FD...
Page 96 Displays signal status that is input to VDEC. Sub Address Sub Address Device Meaning (Main screen) (Sub screen) 205h 605h CC detection 1 208h 608h CC detection 2 VDEC 20Bh 60Bh CC-CRI detection 20Ch 60Ch XDS content advisor 0 20Dh 60Dh XDS content advisor 1 PDP-6010FD...
Page 97 E R R O R E R R O R 6.2.1.14 DTV TV-GUIDE BER Exclusively used for production line. TV-Guide error bit ratio information is displayed. 6.2.1.15 DEBUG INFO Exclusively used for technical analysis. Debug information for development use is displayed. PDP-6010FD...
Page 98: Panel Factory (+)
RASTER MASK SETUP (+) The mask indication (RASTER) can be set and indicated. 6.2.2.10 PATTERN MASK SETUP (+) The mask indication (PATTERN) can be set and indicated. 6.2.2.11 COMBI MASK SETUP (+) The mask indication (COMBI) can be set and indicated. PDP-6010FD...
Page 99 • P-COUNT: The accumulated power-on count is indicated. • TEMP1: The current panel temperature and the historical maximum temperature recorded in memory are indicated. The range of temperature indication is from -50.0 to +99.9. (The temperature unit is " °C (Centigrade) ".) PDP-6010FD...
Page 100 MAIN EEPROM Communication Error MDU-IIC MD-IIC BACKUP BACKUP EEPROM Communication Error DAC1 DAC1 Communication Error DAC2 DAC2 Communication Error − − Abnormally in RST2 power supply RST2 High temperature of the panel TEMP-H Panel temperature TMP-NG Low temperature of the panel TEMP-L PDP-6010FD...
Page 101 <VOL+> : Adding by 10 to the adjustment/ setting value <VOL-> : Subtracting by 10 from the adjustment/setting value F S E < = > <SET> : Determining the adjustment/setting value and shifting to the upper layer PDP-6010FD...
Page 102 The number of the adjustment table and the drive sequence currently selected are displayed on the right side of the third line as the On-Screen display. Drive sequence and adjustment table Sequence Name Video50 Video60 Video72 Video75 PC60 Adjustment Value TBL2 TBL1 TBL1 TBL3 TBL4 Table PDP-6010FD...
Page 103 : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer – < = > PDP-6010FD...
Page 104 : Shifting to the previous item <RIGHT> : Adding by one to the adjustment/ setting value <LEFT> : Subtracting by one from the adjustment/setting value <SET> : Determining the adjustment/setting value and shifting to the upper layer < = > O P R T PDP-6010FD...
Page 105 M A S K • The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-6010FD...
Page 106 M A S K • The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-6010FD...
Page 107 M A S K • The MASK indication sequence can be changed among 48V, 50V, 60V, 72V, 75V and 60P using the Right or Left key. The selected sequence and the ABL/WB table are retained until the mask is turned off. PDP-6010FD...
Page 108 Exclusively used for production line. 6.2.3.2 ANTENNA MODE <=> Exclusively used for production line. 6.2.3.3 AFT <=> Exclusively used for production line. 6.2.3.4 SYNC DET (+) Exclusively used for technical analysis (details omitted). 6.2.3.5 CC (+) Exclusively used for technical analysis (details omitted). PDP-6010FD...
Page 109: Initialize
• When the configuration is set to <YES> and the [ENTER/SET] key is pressed for 5 seconds, the reset action executes. Be sure to disconnect and connect the AC cable after FINAL SETUP. When replacing the MAIN Assy, the FINAL SETUP is required. PDP-6010FD...
Page 110 Be sure to do above procedure at input fuction except HMG. For details, refer to the service manual for the ELITE model. HG (Home Gallery) SERVICE MODE (Regular model) 1. Home Gallery Screen (1) When the USB device is connected (2) When the USB device is not connected PDP-6010FD...
Page 111 6 S (String descriptor info - 2) Product String 7 S (String descriptor info - 3) String SerialNumber 2. End method It is the same as the case that Home Gallery displays. 6.2.4.4 Wide XGA AUTO <=> Exclusively used for technical analsyis (details omitted). PDP-6010FD...
Page 112: Disassembly
Y DRIVE Front case Assy (608U) 42/60LED FHD RLS FHD IR POWER SW Under cover (60U) Multi base Terminal panel A Front chassis Section VL Assy 60 PANEL TANSHI DIGITAL SENSOR SCAN A SCAN B SCAN C SCAN D PDP-6010FD...
Page 113: Disassembly
Remove the speaker system. Remove the three brackets by removing the six screws. Speaker cable ×2 ×2 Bracket ×2 Bracket Speaker system Bracket ×2 (When using the hung on wall unit.) ×2 (When using the Pioneer table top stand.) PDP-6010FD...
Page 114 Remove the side input cover. Handle Remove the four screws. Remove the two handles. Sub frame cover L, R Remove the six screws. Remove the sub frame cover L and R. Handle Sub frame cover L Sub frame cover R Handle PDP-6010FD...
Page 115 Tighten the one screw. Rear case (608) Tighten the one screw. Tighten the six screws. Secure the remaining screws, center ones first then the peripheral screws, to avoid an upward shift of the central part of the rear case. PDP-6010FD...
Page 116 TANSHI Assy MAIN Assy pry the connector upward to remove it. TANSHI Assy MAIN Assy PDP-6010FD...
Page 117 Remove the Front case Assy (608U), by pulling it upward. Removal of only the Front Case Assy If only the front case Assy must be removed, follow the procedure below: Remove the 22 screws. Rear case (608) Under cover (60U) 1 1 1 PDP-6010FD...
Page 118 Lift the Multi base section to the direction of the arrow. Fix the multi base section to the product with two reuse wire saddles. Multi base section Reuse wire saddle 60F DIGITAL Assy PANEL SENSOR Assy Multi base section PDP-6010FD...
Page 119 60F SCAN D Assy Assy Assy Assy Notes for Three pieces connector 40P* Three pieces connector 40P is a precision part. Pay attention to the handling. Connecting Method Disconnecting Method In addition, please do not touch the electrode plane. PDP-6010FD...
Page 120: Disassembly And Reassembly Precautions For Speaker System
Otherwise, it may be damaged. OK: Good example NG: Bad example Baffle Assy (Caution) Grille Assy When reassembling the cabinet and the baffle plate, secure the screws in the order shown in the figure below: Baffle Grille Assy Front Baffle PDP-6010FD...
Page 121: Each Setting And Adjustment
3. Select “Channel Setup”. ( then ENTER) 4. Select “POD ID”. ( • The Host ID and Cable Card ID appear. 5. Press HOME MENU to exit the menu. (*) : When replacing the MAIN Assy, be sure to perform the FINAL SETUP. PDP-6010FD...
Page 122 “8.5 ADJUSTMENTS WHEN THE DRIVE ASSYS ARE REPLACED. No adjustment required ADDRESS Assy No adjustment is required after replacement of parts PANEL SENSOR Assy other than those mentioned above. No adjustment required TANSHI Assy PDP-6010FD...
Page 123: Backup Of The Eeprom (Digital Assy)
1 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 2 Issue the BCP command to transfer the data stored in the EEPROM for backup. 3 Turn the power off. PDP-6010FD...
Page 124 1 Turn on the unit, using the remote control unit or by issuing the PON command. Then issue the FAY command. 2 Issue the UAJ command to delete data stored in the EEPROM on the DIGITAL Assy. 3 Issue the BCP command to transfer the data stored in the EEPROM for backup. 4 Turn the power off. PDP-6010FD...
Page 125 When a DIGITAL Assy with an EEPROM in which adjustment data are stored is mounted, this step is not required after manual adjustment. ("DIGITAL EEPROM: REPAIR" is not indicated.) (2) Method using the RS-232C commands Issue the FAJ command. PDP-6010FD...
Page 126: How To Clear History Data
P COUNT INFO. < = > : NO OPRT Right P COUNT INFO. < = > : CLEAR SET (5 sec) MAX TEMP. < = > : NO OPRT Right MAX TEMP. < = > : CLEAR SET (5 sec) 3 Turn the power off. PDP-6010FD...
Page 127: Adjustment When The Service Panel Assy Is Replaced
[DIZ S03] : Dither ON, L dither ON, noise OFF. [$1800000001] : LUT mode ON [$1000003F00] : Reset active control OFF. ∗: If the unit is shut down during the above adjustment flow, resend the above commands from the beginning. PDP-6010FD...
Page 128 (RST MASK 23: Magenta 3SF) Checking VOL YNOFS3/4/1 (min) (RST MASK 16: Green 1023+) Replacement with the parts for service Checking VOL YNOFS3/4/1 (min) • Re-replacement of the panel (RST MASK 15: Red 1023+) • Replacement of the DRIVE Assy PDP-6010FD...
Page 129 : To set the gamma G value to that for Factory mode [PGB S00] : To set the gamma B value to that for Factory mode [DIZ S03] : Dither ON, L dither ON, noise OFF. [$1800000001] : LUT mode ON [$1000003F00] : Reset active control OFF. PDP-6010FD...
Page 130 (Check on the PANEL 1-ADJ menu.) Return VOL OFFSET to the tentative setting value. / [VOF ∗∗∗] Determine the tentative setting value for VOL OFFSET as the final value. From the Recovery flowchart (1-2) and (1-4) [To the Main flowchart (2)] PDP-6010FD...
Page 131 Determine the tentative setting value for VOL YNOFS4 as the final value. *1: The tentative setting value becomes the final value. Determine the tentative setting value for VOL YNOFS1 as the final value. From the Recovery flowchart (2-1) and (2-3) [Adjustment completed] PDP-6010FD...
Page 132 Display RST MASK 02 (Red). / [MKS S52] Set VOL OFFSET to the current setting value plus 85. / [VOF ***] Replacement of abnormal circuits or Is there erroneous discharge (abnormal dead cell)? re-replacement of the panel required (Check on the PANEL 1-ADJ menu.) PDP-6010FD...
Page 133 (dead cell). The VOL OFFSET value must be 107 or greater. Replacement of abnormal circuits or Current VOL OFFSET < 107? re-replacement of the panel required Display RST MASK 03 (Green). / [MKS S53] [To the Recovery flowchart (1-4)] PDP-6010FD...
Page 134 (Check on the PANEL 1-ADJ menu.) Set VOL OFFSET to the current setting value plus 37. / [VOF ***] Determine the current VOL OFFSET setting value as the final value. [To the Main flowchart (2)] PDP-6010FD...
Page 135 Set VOL YNOFS3 to the current setting value plus 43. / [VY3 ***] Set VOL YNOFS4 to the current setting value plus 43. / [VY4 ***] Replacement of abnormal circuits or Is there erroneous discharge (abnormal lit cell)? re-replacement of the panel required (Check on the PANEL 1-ADJ menu.) PDP-6010FD...
Page 136 Set VOL YNOFS4 to the current setting value plus 4. / [VY4 ***] Replacement of abnormal circuits or Current VOL YNOFS3 setting value > 095? re-replacement of the panel required Is there erroneous discharge (abnormal dead cell)? [To the Recovery flowchart (2-1)] PDP-6010FD...
Page 137 Note: Make a note of this VOL YNOFS3 value. Set VOL YNOFS1 to the final setting valueof YNOFS3 minus 18. / [VY1 ***] Determine the current VOL YNOFS1 setting value as the final value. [To the Main flowchart (2)] PDP-6010FD...
Page 138 Setting Voltages Vysnofs (V) Vyprst (V) Vyknofs1,2 (V) Vyknofs3 (V) Vyknofs4 (V) PDP-6010FD...
Page 139 Setting Voltages Vyprst (V) Vyknofs1,2 (V) Vyknofs3 (V) Vyknofs4 (V) Vyprst (V) PDP-6010FD...
Page 140: Adjustment When The Drive Assys Are Replaced
Adjust so that "Δ Tsus - gub = Δ Tsus - iub + α ± 5 nsec," using the variable controls shown in the table below: Value of α Assy X DRIVE Assy VR1002 70 nsec Y DRIVE Assy VR2002 60 nsec PDP-6010FD...
Page 141 (input to the gate terminal of Q2111) SUS-D pulse width: Tsus - Dg Adjust so that "Tsus - Dg = Tsus - D ± 5 nsec," using the variable control shown in the table below: Assy Y DRIVE Assy VR2001 PDP-6010FD...
Page 142 2 Adjust the pulse width (Tsus - Dg) of the SUS-D Y DRIVE Assy input signal so that it becomes "Tsus-D ± 5 nsec." 1 Measure the SUS-D pulse width (Tsus - D). TP2114 from VR2001 IC2104 DIGITAL Assy Q2111 IC2005_A7 Q2105 IGBT YSUS-D Q2113 IGBT TP2116 PDP-6010FD...
Page 143: Precaution On Replacement Of The Power Supply Unit
Disconnect the housing wire (J126) from the P11 terminal Connect the housing wire (J126) to the P11 terminal on the old POWER SUPPLY Unit. on the new POWER SUPPLY Unit. Housing wire (J126) Housing wire (J126) POWER SUPPLY unit (old) POWER SUPPLY unit (new) PDP-6010FD...
Page 144: Rs-232C
9.1.2 USING RS-232C COMMANDS Individual ports are provided for RS-232C and SR+ connectors with this model. Therefore, unlike the case of previous models, which required switching of exclusive operation between these connectors on the Integrator menu, switching is no longer required. PDP-6010FD...
Page 145: List Of Rs-232C Commands
Dither/L dither ON & noise ON Dither/L dither OFF & noise ON Dither/L dither ON & noise OFF Panel drive-power OFF Panel drive-power ON To subtract ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, designated by a function command) PDP-6010FD...
Page 146 Green vertical line scroll Green horizontal line scroll Vertical ramp vertical scroll (white) Vertical ramp vertical scroll (green) Horizontal ramp horizontal scroll (white) Horizontal ramp horizontal scroll (green) Cross hatch + window MASK OFF H ramp (slant 1) H ramp (slant 4) PDP-6010FD...
Page 147 For panel light check 1 For panel light check 2 5 for perfect linear 6 for perfect linear 7 for perfect linear 8 for perfect linear Mask for ABL adjustment Raster - White Raster - Red Raster - Green PDP-6010FD...
Page 148 Panel drive mode (STANDARD) Panel drive mode (DYNAMIC) Panel drive mode (MOVIE) Panel drive mode (GAME) Panel drive mode (SPORTS) Panel drive mode (PURE) Panel drive mode (USER) Panel drive mode (ISF-DAY) Panel drive mode (ISF-NIGHT) Panel drive mode (OPTIMUM PDP-6010FD...
Page 149 Green-independent gamma setting: Fixed on 2.2 (default) Green-independent gamma setting: Fixed on 2.3 Green-independent gamma setting: Fixed on 2.4 S10-31 Green-independent gamma setting: Customize ∗∗∗ Panel white balance adjustment - Green highlight ∗∗∗ Panel white balance adjustment - Green low light PDP-6010FD...
Page 150 Each information output for panel Acquiring unit data, such as the software version common to all models, regardless of destination Acquiring data on shutdown Acquiring data related with signals Acquiring the software sub-version of the microcomputer at panel side PDP-6010FD...
Page 151 Measures against AM radio noise - SUS FREQUENCY MODE 5 Measures against AM radio noise - SUS FREQUENCY MODE 6 Measures against AM radio noise - SUS FREQUENCY MODE 7 Measures against AM radio noise - SUS FREQUENCY MODE 8 PDP-6010FD...
Page 152 Theater port interlock operation OFF Theater port interlock operation ON Determining the flag for the DIGITAL Assy adjustment in "not adjusted" To add ∗∗∗ to the adjustment value (∗∗∗ = 000 to 999, designated by a UP∗ function command) PDP-6010FD...
Page 153 3SF and later-YSUS Tail (resonance down width) UP*/DN* is not effective ∗∗∗ 2SF-repeat YSUS (resonance up width) UP*/DN* is not effective Initializing the video EEPROM data Initializing the setting data to which no adjustment command is provided PANEL EEPROM REFLESH PDP-6010FD...
Page 154: Details Of Each Commands
2: Panel Generation 8th byte 2nd PLANT (XGA 50 inch only) System model 1st PLANT (XGA 50 inch only) All-in-one design TV PLANT information and SQ_LSI version ∗ Monitor mismatching (version mismatching at SD) Standard module ‘ Others Simple module PDP-6010FD...
Page 155: Qs2 (Panel Operation Data)
X-DRV Adjustment not MASK-OFF completed X-DCDC MASK-ON X-SUS DIG-DCDC 14 to 17: Detection of Each Protection function 3: Adjustment-data Not used Normal operation backup flag Not used At detection of protection operation With backup data UNKNOWN No backup data PDP-6010FD...
Page 156: Qs3 (Other Data On The Panel)
PON COUNTER 8 byte 00000000 Note TEMP1 acquisition (Temperature value) 5 byte +25.0 (*1) (*1) : Centigrade scale TEMP0 acquisition (Temperature value) 5 byte +25.0 (*1) MaxTEMP acquisition (Temperature value) 5 byte +75.0 (*1) ∗∗∗∗ Reserved 4 byte 2 byte PDP-6010FD...
Page 157: Qaj (Panel Adjustment Data)
ADDRESS 1, 2 setting value 2 byte ADDRESS 3, 4 setting value 2 byte ADDRESS 5, 6 setting value 2 byte ADDRESS 7, 8 setting value 2 byte Streaking correction 1 byte AM radio countermeasure 1 byte ∗∗ Reserved 2 byte 2 byte PDP-6010FD...
Page 158: Qpw (Video Adjustment Data Of The Panel)
QPM (fixed) Pulse meter B 1 8 byte 00000000 Pulse meter B 2 8 byte 00000000 Pulse meter B 3 8 byte 00000000 Pulse meter B 4 8 byte 00000000 Pulse meter B 5 8 byte 00000000 2 byte PDP-6010FD...
Page 159: Qpd (Pd Logs)
Data from the hour meter for the seventh latest PD 8 byte 00000213 Eighth latest "1st PD" data 1 byte Eighth latest "2nd PD" data 1 byte Data from the hour meter for the eighth latest PD 8 byte 00000123 2 byte PDP-6010FD...
Page 160: Qsd (Sd Logs)
Data from the hour meter for the seventh latest SD 8 byte 00000000 TEMP1 (high temperature) Eighth latest SD data 1 byte TEMP1 (low temperature) Eighth latest SD subcategory data 1 byte Data from the hour meter for the eighth latest SD 8 byte 00000000 2 Byte PDP-6010FD...
Page 161: Qse (Destination Peculiar Information)
3 byte A/D value of MTB-side Temperature 3 byte MTB-side FAN rotating speed (0: STOP, 1: LOW, 2: HIGH) 1 byte A/D value of room light sensor 3 byte Level of room light sensor (Value: 1 to 5) 1 byte PDP-6010FD...
Page 162: Qng (Shutdown Information Of Mtb)
Failure of Power Supply at MTB side Go to No. 13 Subcategory Information 14(E) Startup failure of Home Media Gallery 15(F) Failure of Main EEPROM Immediately Shutdown ∗: Indicates the frequency of Blue LED flashing when the shutdown is occurred. PDP-6010FD...
Page 163 Shutdown Home Gallery AD/PLL Shutdown Middleware HDMI Shutdown Application Tuner 2 Shutdown US-MSP Shutdown < No. 13 Subcategory Information on "Failure in Power supply at MTB side" > Value Shutdown Factor Remarks (Operation) RST 2 Shutdown RST 4 Shutdown PDP-6010FD...
Page 164: Qsi (Input Signal Data)
Once the DRIVE OFF command is accepted, DRIVE OFF cannot be canceled by pressing the DRIVE OFF key again or by turning the unit off then back on with the STANDBY OFF/ON key. To cancel DRIVE OFF, restart the unit by unplugging then again plugging in the power cord. PDP-6010FD...
Page 165: Fay / Fan (Adj. Commands Permission / Prohibition)
To make the flag setting that indicating that adjustment of the main [UAJ] unit has not been completed During FAY To make the flag setting that indicating that backup data have not The backup ROM is [CBU] been copied initialized. To copy Digital backup data to EEPROM [BCP] PDP-6010FD...
Page 166: Exploded Views And Parts List
(In the case of no amount instructions, apply as you think it appropriate.) 10.1 PACKING SECTION Screw ×6 Plastic band ×4 (M5 × 10 mm: silver) Speed clamp ×3 Screw ×4 Screw ×4 (M6 × 20 mm: black) (M4 × 10 mm: black) Bead band ×3 PDP-6010FD...
Page 167 Stand Pipe L Assy AXY1186 Stand Pipe R Assy AXY1187 Base Cover Assy AXY1198 Reinforce Carton LR AHC1097 Pad (608 B-L) AHA2692 Pad (608 B-R) AHA2693 Pad (608 B-C) AHA2694 Under Carton (607) AHD3548 Speaket System SMW1986 DCF Cleaning Caution ARM1377 PDP-6010FD...
Page 168: Rear Section
10.2 REAR SECTION MAIN CN4109 MAIN CN4110 (USB) CN8801 CN8802 TANSHI Refer to "10.3 FRONT SECTION". PDP-6010FD...
Page 169 Sub Frame Cover L AMR3586 Sub Frame Cover R AMR3587 Label B50 (U) AAX3540 Under Cover (60U) ANC2434 Screw AMZ30P060FTB Screw APZ30P100FTB Screw APZ40P100FTB Screw ABA1341 Screw AMZ30P080FTC Screw PMB30P100FTB Screw PMB40P140FTB Screw BPZ30P080FTB Screw BBZ30P060FTB Screw BPZ30P100FTB Gasket (J-type) ANK1956 PDP-6010FD...
Page 170: Front Section
10.3 FRONT SECTION Refer to "10.4 CHASSIS SECTION (1/3)". MAIN CN4107 MAIN CN4109 Rear view PDP-6010FD...
Page 171 AWW1276 FHD RLS Assy AWW1292 FHD IR Assy AWW1289 Blind Cushion AEB1449 PCB Spacer AEC1947 1..Front Case Assy (608U) AMB3035 2..Coil Spring ABH1126 NSP 8 2..Panel Cushion H AED1318 • • • • • 2..Power Button AAD4157 Screw BPZ30P080FTB PDP-6010FD...
Page 172: Chassis Section (1/3)
10.4 CHASSIS SECTION (1/3) Refer to "10.8 MULTI BASE SECTION". Refer to "10.5 CHASSIS SECTION (2/3)". PDP-6010FD...
Page 173 ANG2937 Protector Sheet AMR3713 Reuse Wire Saddle AEC2118 Wire Clip AEC1948 Wire Saddle AEC1745 PCB Spacer AEC1947 PCB Spacer (44.8) AEC2121 Gasket MTB ANK1879 Screw AMZ30P060FTB Screw TBZ40P080FTB Screw ABA1313 Screw ABA1364 Reuse HL 28 AEC2119 Reuse Clamp AEC2129 PDP-6010FD...
Page 174: Chassis Section (2/3)
10.5 CHASSIS SECTION (2/3) Cleaning liquid : GEM1004 Cleaning paper : GED-008 FHD FAN CONNECT CN9555 FHD FAN CONNECT CN9554 FHD FAN CONNECT CN9553 Refer to "10.6 CHASSIS SECTION (3/3)". MAIN CN4103 POWER SUPPLY PDP-6010FD...
Page 175 ABA1313 Screw AMZ30P080FTC Screw APZ30P100FTB Screw AMZ30P060FTB Screw BPZ30P080FTB Reuse Wire Saddle AEC1945 Fan Cover Sheet AMR3739 Digital Cover Sheet AMR3736 Flat Clamp 60 AEC2104 PCB Spacer (Reuse) AEC2087 Flat Clamp AEC1879 Reuse HL 28 AEC2119 Reuse Clamp AEC2129 PDP-6010FD...
Page 176: Chassis Section (3/3)
10.6 CHASSIS SECTION (3/3) MAIN CN4101 MAIN CN4105 TANSHI CN8806 MAIN CN4106 POWER SW CN9571 AC Inlet Fan×3 MAIN CN4113 Refer to "10.7 PANEL CHASSIS SECTION". PDP-6010FD...
Page 177 Ferrite Core (F1 - F8) ATX1048 Ferrite Clamp AEC1986 PCB Spacer (4.5) AEC2115 Reuse Wire Saddle AEC2118 Reuse HL 28 AEC2119 • • • • • • • • • • Drive Silicone AEH1139 • • • • • PDP-6010FD...
Page 178: Panel Chassis Section
10.7 PANEL CHASSIS SECTION PDP-6010FD...
Page 179 ANK1947 PCB Spacer (Reuse) AEC2122 3 Piece Connector 40P (CN101) AKM1384 3 Piece Connector 40P (CN102) AKM1384 Scan Silicone AEH1135 PCB Spacer AEC1947 Conductive Plate Holder AMR3446 Screw ABA1351 Screw (M3x6) ABA1366 Conductive Plate Y ANG3058 Spacer (4.5) AEC2116 PDP-6010FD...
Page 180: Multi Base Section
10.8 MULTI BASE SECTION 42/60LED CN9601 SIDE KEY CN9501 FHD IR CN9731 60F DIGITAL CN3201 FHD RLS CN9781 POWER (side) FHD FAN CONNECT CN9551 POWER POWER SIDE IO CN9352 SIDE IO CN9351 PDP-6010FD...
Page 181 Terminal Panel A (U) ANC2440 POD Stay A ANG2933 • • • • • Gasket UD ANK1883 Hex. Head Screw BBA1051 Washer Faced Nut BBN1005 Screw BMZ30P060FTB Screw PMB30P080FNI 6P Housing Wire (J115) ADX3582 4P Housing Wire (J122) ADX3584 PDP-6010FD...
Page 182: Pdp Service Assy 608F (Awu1274)
10.9 PDP SERVICE ASSY 608F (AWU1274) Exterior Section PDP-6010FD...
Page 183 Packing Section Refer to the “• Exterior Section” for the mounting position. ×13 ×6 ×8 ×4 ×1 PDP-6010FD...
Page 184 Front Case Assy (608 service) AMB3057 Rear Case (608) ANE1664 Screw ABA1351 Screw ABA1364 Screw (M3 x 6) ABA1366 Screw ABZ30P080FTC Screw AMZ30P060FTB Screw APZ30P100FTB Screw BPZ30P080FTB Screw TBZ40P080FTB • • • • • • • • • • • • • • • PDP-6010FD...
Page 185: Speaker System (Packing)
1..Bracket Assy (C) SXG1131 Protection Sheet (R) SHC1861 2..Gasket SED1160 Packing Case SHG2781 2..Gasket SED1161 2..Gasket SED1162 Packing Bag S2 SHL1450 2..Gasket SED1163 NSP 40 CS Assy SMW1988 2..Gasket SED1164 NSP 41 Serial Label SRW1112 NSP 21 2..Bracket C SNA1480 PDP-6010FD...
Page 186: Cs Assy
10.11 CS ASSY Tweeter Input Terminal PDP-6010FD...
Page 187 NSP 36 Acoustic Absorbent SMT1357 NSP 37 Acoustic Absorbent SMT1358 NSP 38 Acoustic Absorbent SMT1359 NSP 39 Acoustic Absorbent SMT1360 NSP 40 Acoustic Absorbent SMT1361 NSP 41 Model Label SAN3956 NSP 42 Caution Label SRR1024 NSP 43 Serial Label SRW1111 PDP-6010FD...
Page 188 PDP-6010FD...
Page 189 Changed contents Mark Date Rev. No. SM Correction No. Revision Page Correct numbers of the following parts. 20-Jan-09 SCH08025 EXPLODED VIEWS/PACKING SECTION/3 Battery Cover PDP-6010FD...

Pioneer PDP-6010FD Service Manual

1 Service Precautions

2 Specifications

3 Basic Items for Service

4 Block Diagram

5 Diagnosis

6 Service Factory Mode

7 Disassembly

8 Each Setting and Adjustment

9 Rs-232C

10 Exploded Views and Parts List

Quick Links

Related Manuals for Pioneer PDP-6010FD

Summary of Contents for Pioneer PDP-6010FD

Table of Contents