Door Lock, 3-Pin Connector; Adjusting The Sensor - Directed Electronics Viper 5902 Installation Manual

H3/5 GREEN
H3/6 RED
H3/7 PINK/WHITE
H3/8 PINK/BLACK
H3/9 RED/BLACK
H3/10 NC

Door Lock, 3-pin connector

1 BLUE
2 EMPTY
3 GREEN

Adjusting the Sensor

Important! Make sure the keypad is unlocked and the vehicle is disarmed with no open zones. The on board
shock sensor can be adjusted using the HD remote.
Adjusting the sensor:
1. the system, turn the ignition Off and close all the doors.
Disarm
2. To enter Sensor Adjust,
the display is blank. When the
Adjustments screen and then press in on the menu wheel to enter.
Adjustments menu, highlight Sensor Adjust and press the Menu Wheel. The remote requests the
3. In the
current setting from the system and displays it in the Sensor Adjustment screen.
4. Follow the on screen instructions to change the setting in the display.
5. the menu wheel up/down or press the
Toggle
6. When you have reached the desired level,
setting in the display to the system; a long beep confirms the new level is set. To reset the level to factory
default, press the
AUX
Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the
siren chirps, indicating the impact level required to fully trigger the alarm.
button to exit and return to the Adjustments menu. The setting retains the last saved.
7. Press the
AUX
To exit the shock sensor adjustment mode from the control module:
Open an entry point or turn on the ignition, the control module emits one long chirp exiting adjustment
mode.
During level setting and level testing if more than 30 seconds lapses without any action the system will exit
sensor adjust and return to the Adjustment menu.
Adjusting the sensor with the 1way remote:
1. Disarm the system, turn the ignition Off and close all the doors.
2. Press and hold the
Select beep after 3 seconds) or until the amber LED turns on.
3. Press and hold the
module emits one long chirp, confirming that it has entered adjustment mode.
4. Press the , or
Note: You can test the new setting by cautiously impacting the vehicle with increasing intensity until the
AUX
AUX
siren chirps, indicating the impact level required to fully trigger the alarm.
• button: Pressing this button increases the sensitivity one level. The siren chirps twice confirming the
sensitivity adjustment.
AUX
• button: Pressing this button decreases the sensitivity one level. The siren chirps once confirming the
sensitivity adjustment.
AUX
© 2009 Directed Electronics. All rights reserved.
Bitwriter Neutral Safety
Port Switch
(+) STARTER INPUT (KEY SIDE OF THE STARTER KILL)
IGNITION 1 +12V INPUT (30A FUSED)
(30) FLEX RELAY OUTPUT (car side of ign, acc or starter wire)
1
(87a) FLEX RELAY INPUT (key side of ign, acc or starter wire if needed)
1
ACCESSORY/STARTER RELAY +12V INPUT (30A FUSED)
No Connection
1 8
1 5
1 3
(-) 500mA UNLOCK OUTPUT
NOT USED
(-) 500mA LOCK OUTPUT
press in and hold the menu wheel (for 3 seconds) on the remote control while
Settings
press and hold the menu wheel, the remote sends the level
button.
AUX
button of the remote control for 8 seconds (If Car 2 mode is on, ignore the Car
button 1.5 seconds or until the amber led flashes then comes on solid.- The control
AUX
buttons to adjust the sensor level.
AUX
Remote Door Lock/ H2
Start In Unlock Output Port
10 9 8 7 6
12
5 4 3 2 1
10
1
screen appears, toggle the menu wheel up or down to the
/ buttons to change level.
AUX
AUX
Relay Out Valet Status
Port Port LED
12
R
4 3
ELECTRONICS
2 1
TACH LEARN THREASHOLD
JMP1 OFF ON
7