Specifications - RIDGID PCS-500 Manual

Specifications

Model .............................Small Clamp
(PC-106)
Nominal Pipe Cutting
Capacity.........................1" to 6" (25mm to 150mm)
Actual Pipe
Outside Diameter ............1.26" to 6.625" (32mm to 168mm)
Blade Type.......................Cermet-Tipped
Pipe Material
(With Proper Blade).........Steel, Stainless Steel
and most Metal***
Maximum Wall
Thickness ........................½" (12mm)
Maximum Pipe Out of
Roundness** ...................Less Than 1.5% of Nominal Pipe Outside Diameter
Minimum Cut-off
Length .............................1" (25mm) (PipeSaw Not For Facing Pipe End)
Cut Quality (Max. Offset)...0.050" (1.27mm)
Saw Blade Type...............8" Outside Diameter with
Motor:
Power .........................1800 W
Voltage .......................110V - 120V a.c.
Current .......................15 Amp
No Load Operating
Speed ............................3900 RPM
Controls..........................ON/OFF (I/O) Switch
Weight............................49 lbs. (22.2 kg) w/Small Clamp
Dimension (w/saw
plunged down) ...............21.25" x 16" x 14.5" (540 x 406 x 368 mm)
Dimension (w/saw up)....21.5" x 22" x 14.5" (540 x 559 x 368 mm)
Operating temperature .....14°F to 120°F (-10°C to 49°C)
Storage Temperature ........-10°F to 120°F (-23°C to 49°C)
Sound Pressure (L )*.......88.12 dB(A), K=3
P A
Sound Power (L )*...........98.12 dB(A), K=3
WA
* Sound measurements are measured in accordance with a standardized test per Standard 62841-1.
- Sound emissions may vary due to your location and specific use of these tools.
- Daily exposure levels for sound need to be evaluated for each application and appropriate safety measures taken when needed. Evaluation of exposure levels should consider
the time a tool is switched off and not in use. This may significantly reduce the exposure level over the total working period.
** Pipe Out of Roundness = Maximum outside pipe diameter minus minimum outside pipe diameter (pipe diameter measured with calipers).
*** Cermet-Tipped Blade is optimized for standard mild carbon steel. Reduced blade life can be expected on other materials.
Ability to cut depends on a variety of factors, including material type, chemistry, hardness, amount of material being removed and other factors. In some cases, cuts may not
be able to be made or may result in blade damage. If there are any questions about specific material to be cut, contact Ridge Tool Technical Service Department.
Selection of appropriate materials and instal-
NOTICE
lation, joining and forming methods is the responsibility of
the system designer and/or installer. Selection of improp-
er materials and methods could cause system failure.
Stainless steel and other corrosion resistant materials
can be contaminated during installation, joining and form-
999-995-226.10_REV. A
Large Clamp
(PC-612)
6" to 12" (150mm to 300mm)
6.5" to 12.75" (165mm to 324mm)
Carbide-Tipped
Plastic
0.70" (18mm)
For Plastic Only
5 / " Round Arbor
8
52 lbs. (23.6 kg) w/Large Clamp
24.5" x 20.5" x 14.5" (622 x 521 x 368 mm)
24.5" x 26.25" x 14.5" (622 x 667 x 368 mm)
ing. This contamination could cause corrosion and pre-
mature failure. Careful evaluation of materials and methods
for the specific service conditions, including chemical
and temperature, should be completed before any instal-
lation is attempted. (See NOTICE in Workpiece Preparation
section.)
PCS-500 PipeSaw
Diamond Abrasive
Cast Iron
½" (12mm)
7