Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Westinghouse IK009
Summary of Contents for Westinghouse IK009
- Page 1 INSTALLATION MANUAL REFRIGERATION IK009 INTEGRATION KIT WTB4600, WTB4604, WTB5400, WTB5404, WBE4500, WBE4502, WBE4504, WBE5300, WBE5304, WFB4204, WRB5004 Also suitable on selected Electrolux and Kelvinator 400L - 500L Tom Mount, Bottom Mount and Single Door Fridges and Freezers...
-
Page 2: Table Of Contents
After unpacking the integration kit, please check it is Securing refrigerator in cupboard ......13 not damaged. If in doubt, do not use the integration kit but contact your local Westinghouse Customer Care Attaching slide-bar to cupboard door ....13 Centre. -
Page 3: Refrigerator Integration Kit Items
DESCRIPTION REFRIGERATOR INTEGRATION KIT ITEMS Because this kit is common to a variety of models, you need to select the items required to suit your model. Please be sure to identify the correct slide-housing part (see below), depending on whether your fridge has a curved door or a flat door. -
Page 4: Cupboard Dimensions
DIMENSIONS CUPBOARD DIMENSIONS IMPORTANT! Pages 4, 5, 6, and 7 should be given to the person responsible for cupboard design and construction. The cupboard dimensions required for each model are shown on page 5, 6 & 7. 1. All sizes are internal and measured in millimetres. - Page 5 NOTE: All sizes are internal and measured in millimetres. For ‘lettered’ dimensions refer to the table on page 4. Dim B Dim C + 2x Board thickness Panel A Panel B (sides) (back) 100mm Dim H Dim E Panel D bottom Panel C (top)
- Page 6 DIMENSIONS (CONTINUED) When positioned in a corner the clearance of Dim G on Clearances the hinge side of the cabinet will allow the doors to be When installed the opened enough to enable the removal of the crisper bins.
-
Page 7: Installation Of 120˚ Hinge
INSTALLATION INSTALLATION OF 120˚ HINGE screws attached to mounting plate to attach the hinge to the cabinet. Please follow the instructions below to install the cabinet cupboard door 120º hinge. 37mm mounting plate 120º hinge This dimension is typically 37mm (from centre line of mounting plate Attach mounting plate with 120º... -
Page 8: Attaching The Rear Rollers
INSTALLATION (CONTINUED) ATTACHING THE REAR ROLLERS Once fitted turn the adjusting nut on each roller assembly anti-clockwise three full turns, this will raise the cabinet at the rear by approximately 12mm (ensure that the nut is A set of adjustable back feet/rollers is provided in the kit. -
Page 9: Attaching Top Hinge Bracket
ATTACHING THE TOP HINGE ATTACHING SLIDE-HOUSING TO BRACKET REFRIGERATOR DOORS Remove top hinge cover (Figure 3), cover Ensure slide-housing is positioned squarely clips o . as shown. Remove the three (3) top hinge screws. Ensure that the slide-housing is positioned Elevate hinge. - Page 10 INSTALLATION (CONTINUED) 360mm 100mm 235mm 235mm 235mm 100mm 235mm 100mm 2 door bottom freezer 2 door top freezer single door ...and secure with tape. Two door Single door...
-
Page 11: Placing Refrigerator In Cupboard
NOTE: For single door models, the door handle must be completely removed to provide clearance to the cupboard door and the resulting handle mounting holes hidden with a cover. Installer must use a tape or plastic cover that suits the installation appearance (not supplied). While the slide-housing is taped in position, punch a small hole in the refrigerator door skin corresponding to the four (4) holes in the housing (Figure 5). -
Page 12: Refrigerator Alignment
INSTALLATION (CONTINUED) REFRIGERATOR ALIGNMENT Figure 9a - Hinge side Position the refrigerator in the cupboard so that: Top hinge bracket is against cupboard wall (Figure 8). Front of refrigerator cabinet (with doors open) is parallel to and approximately 100mm from the front of the cupboard (Figure 9). -
Page 13: Securing Refrigerator In Cupboard
SECURING THE REFRIGERATOR IN ATTACHING SLIDE-BAR TO THE THE CUPBOARD CUPBOARD DOOR NOTE: When attaching all screws to cupboard, first drill Fully open cupboard door (120°). a 2mm pilot hole in the correct position. This will allow Open refrigerator door until it rests against the easy hand insertion of self tapping screw. - Page 14 INSTALLATION (CONTINUED) Rotate slide-bar to lower alignment, mark a line Secure slide-bar by driving a cupboard screw on cupboard door (Figure 16). Figure 16 into the centre of the inner slot Fig 19. Gently test closing the door. Figure 16...
-
Page 15: Notes
Open and close the door a number of times. If the action is not smooth, loosen the screws and re-adjust the slide bar. Once the desired smooth action is achieved attach the central locking screw Fig 21. Figure 21 Repeat this procedure for the second slide bar if necessary. - Page 16 NEW ZEALAND Electrolux (NZ) Limited Phone: 0800 436 234 Email: customercare@electrolux.co.nz Website: westinghouse.co.nz and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license. All Rights Reserved. P/No. A04633102 © 2017 Electrolux Home Products Pty Ltd. ABN 51 004 762 341...