Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for PURE SUPA-BOUNCE
Summary of Contents for PURE SUPA-BOUNCE
- Page 1 SUPA-BOUNCE 14FT TRAMPOLINE SET MODEL# 9414TS - TRAMPOLINE PRODUCT MANUAL - VERSION 4.21.01 FOR AGES: WEIGHT LIMIT: TOOLS NEEDED: ADULT(S) NEEDED: 145 Kgs CUSTOMER SERVICE GQBrands.com • CustomerService@GQBrands.com • 1-866-498-5269 • 4401 Samuell Blvd, Ste 150, Mesquite, TX 75149...
-
Page 2: Customer Service Information
CUSTOMER SERVICE INFORMATION Thank you for purchasing: SUPA-BOUNCE 14FT Please Note: In the interest of better quality and value, we are constantly improving and updating our product information. Most up to date TRAMPOLINE SET manuals, warnings and product information can be found at: https://www.globalqualitybrands.com/warnings... - Page 3 WARNINGS Assembly, Installation, Care, Maintenance and Use Instructions WARNING Read these materials prior to assembling and using this trampoline Please read all of the warnings and directions below prior to assembly. This trampoline comes equipped with warnings and instructions for the assembly, care, maintenance and use of the trampoline.
-
Page 4: Warning Labels
WARNING LABELS WARNING ADVERTENCIA DO NOT attempt or allow somersaults. Landing on the head or neck NO intente ni permita saltos mortales. Aterrizar sobre la cabeza o el can cause serious injury, paralysis, or death, even when landing in the cuello puede causar lesiones graves, parálisis o la muerte, incluso al middle of the bed. - Page 5 WARNING & SAFETY INFORMATION Please read these warnings and the information in this manual in its entirety. Failure to comply with the following instructions may increase the risk of serious injury and/or death: • The owner and supervisors of this trampoline •...
-
Page 6: Product Safety Information
You can purchase an • As your trampoline mat is raised off the ground, ANCHOR KIT for your trampoline from Pure Fun, by there is the risk of falling when entering or exiting the visiting us on the web at: www.PureFun.Net trampoline. -
Page 7: Basic Trampoline Skills
BASIC TRAMPOLINE SKILLS The following exercises are examples of instructions for use of this exercise trampoline. It is highly recommended to stretch and warm up for at least 10 minutes before starting any exercise. Jumpers should practice these basic techniques and perfect them. Fundamental Bounce Knee Drop Start from a standing position with your head erect... - Page 8 BASIC TRAMPOLINE SKILLS Seat Drop Front Drop Land in a sitting position with your legs parallel to the Start from a low bounce and land on the bed in a bed. prone position. Place your hands on the bed beside your hips. Keep your head up and your arms extended forward Push with your hands to return to an erect position.
- Page 9 BUILDING YOUR TRAMPOLINE This is a 2 person build. Time for build is approximately 2 hours. Choose a good location: On the surface that is soft (wood chippings, sands or grass). Ensure adequate overhead clearance. A minimum of 24ft. (7.3m) from ground level, away from wires, trees and othe possible hazards.
-
Page 10: Trampoline Parts List
TRAMPOLINE PARTS LIST Part # Description Part# Description Leg Extension Jump Mat Curved Top Rail U Shaped Leg T-Section with Bolt Spring Frame Pad M6x45mm Bolt Wrench Spring Tool (4a) M6 x 45mm GQBrands.com CustomerService@GQBrands.com 1-866-498-5269... - Page 11 TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 1: Gather all 12 Curved Top Rails (Part 2) and 12 T-Sections (Part 3).Flip the Curved Top Rails (Part 2) over so the spring holes are facing up. Make sure to place them all on a flat and secure surface before you begin.
- Page 12 TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 5: Gather all Leg Extensions (Part 5) and U- Shaped Legs (Part 6). You will be attaching 2 leg extensions (5) to each U- Shaped Leg. NOTE: The Leg Extension will have 3 openings. The 2 openings closest to each other, will go on the top and connect to the T- Section at the top of the trampoline.
- Page 13 TRAMPOLINE ASSEMBLY INSTRUCTIONS Figure C Repeat step 8 until you have attached 6 of the leg extensions to the T-Sections which will look like figure shown. Model# 9414TS...
- Page 14 TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 9: Place the Jumping Mat (Part 1) in the middle of the frame and unfold it completely. NOTE: Make sure the stitching of the Jumping mat is facing the floor In order to avoid ripping and to distribute tension when attaching springs to the frame, follow the numbered order shown.
- Page 15 TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 10: Unfold the Frame Pad (Part 8) and place it on top of the Top Rail and springs. The skirt of the Frame Pad must cover the Top Rails completely to avoid injury. NOTE: Make sure the connecting straps are facing down towards the Top Rails in order to secure the Frame Pad to them in Step 10.
- Page 16 TRAMPOLINE ASSEMBLY INSTRUCTIONS STEP 11: Find all the bottom connecting straps of the trampoline frame pad and secure them by tying them in a knot around to the top rail to avoid moving or shuffling when jumping on the trampoline as shown below.
-
Page 17: Enclosure Parts List
ENCLOSURE PARTS LIST Part # Description Part# Description Straight Enclosure Pole Washer Curved Enclosure Pole Enclosure Pole Cap Black String Enclosure Net M6x75mm Bolt Lime Pole Cover Spacer M6x75mm Bolt Model# 9414TS... - Page 18 ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 1: Gather all Curved Enclosure Poles (Part 2) and Enclosure Pole Caps (Part 3). IMPORTANT: Do not attach the Enclosure Pole Caps to the Straight Enclosure Poles. If an Enclosure Pole Cap has been accidentally installed on a straight pole it cannot be removed.
- Page 19 ENCLOSURE ASSEMBLY INSTRUCTIONS Step 3: A. Put the Upper (1) and Lower (2) sections of the Enclosure Poles together as shown on the left. B. If necessary, Attached the Pole Caps (3) to the tops of each Enclosure Pole C. Slide the Pole Covers (10) over the connected Enclosure Poles.
- Page 20 ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 4: A. With the help of another adult, hold the completed enclosure pole by aligning both square holes to begin installation. NOTE: Curved Enclosure Pole must face towards the center of the trampoline. B. Once aligned, attach the completed enclosure pole to the trampoline leg.
- Page 21 ENCLOSURE ASSEMBLY INSTRUCTIONS M6x75mm Bolt Spacer Washer Model# 9414TS...
- Page 22 ENCLOSURE ASSEMBLY INSTRUCTIONS STEP 5: Place the Enclosure Net (Part 9) on top of the trampoline. Align the straps to the corresponding Enclosure Poles so they are as near to each other as possible when lifted. NOTE: Make sure that zipper and buckle snap are facing the outside of the trampoline.
-
Page 23: Frequently Asked Questions
FREQUENTLY ASKED QUESTIONS • Question: “The foam padding or mat is • Question: “I had a part missing from my damaged, what should I do?” Answer: box” or “something was damaged in If you are still within your warranty shipping, can you send it to me?” period (90 Days from initial purchase) Answer: If it has been 30 days or less you should contact customer service.