Application Advice; Maintenance & Service; Noise / Vibration - Skil 2550 Instructions Manual

Dust bag
- mount dust bag AD
• Operating the tool w
- mount battery
- always hold handle S firmly with one hand and handle T
firmly with the other hand
- place tool with front end of foot flat on workpiece
! ensure that the saw teeth are not engaged into the
workpiece
- switch on tool by first pressing knob W (= safety switch
which cannot be locked) and then pulling trigger Y
! the tool should run at full speed before the blade
enters into the workpiece
- lower guard F opens automatically when saw blade
enters the workpiece (open lower guard manually by
using lever G only for special cuts such as plunge cuts)
! do not force the tool (apply light and continuous
pressure in order to avoid overheating the blade
tips)
! while working, always hold the tool at the grey-
coloured grip area(s)
- after completing the cut switch off tool by releasing
trigger Y
! ensure that the blade has come to a complete
standstill, before you lift the tool from the
workpiece

APPLICATION ADVICE

• Always face the good side of the workpiece down to
ensure minimum splintering
Only use sharp saw blades of the correct type r
•
- quality of cut improves by the number of teeth
- carbide tipped blades stay sharp up to 30 times longer
than ordinary blades
• Parallel guide Z t
- for making exact cuts along a workpiece edge
- can be inserted in either side of foot
Adjusting parallel guide
- loosen knob AA
- adjust to desired cutting width by using parallel guide
scale (use line-of-cut indicator Q as 0-reference)
- tighten knob AA
• Plunge cutting y
- set desired cutting depth
- tilt tool forward with line-of-cut indicator Q lined up with
desired line of cut marked on the workpiece
- open lower guard F with lever G
- just before blade enters workpiece, switch on tool and
gradually lower back end of tool using front end of foot
as hinge-point
- gradually move tool downward as well as forward
- as soon as blade enters the material, release lever G
! never pull tool backwards
• Cutting large panels u
- support panel close to the cut either on floor, table or
workbench
! set cutting depth so that you cut through panel
and not through support
- in case parallel guide does not allow desired width of
cut, clamp or nail straight piece of wood to workpiece
as a guide, and use the right side of the foot against
this guide i
• For more information see www.skil.com
MAINTENANCE / SERVICE
• This tool is not intended for professional use
• Always keep tool clean (especially ventilation slots AB )
! remove battery from tool before cleaning
• Always keep the area around lower guard F 2 clean
(remove dust and chips by blowing out with compressed
air or with a brush)
• Clean saw blade immediately after use (especially from
resin and glue)
If the tool should fail despite the care taken in
•
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
• Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
• Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
- in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol 6 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit

NOISE / VIBRATION

• Measured in accordance with EN 62841 the sound
pressure level of this tool is 92.5 dB(A) and the sound
power level 103.5 dB(A) (uncertainty K = 3 dB), and the
vibration ✱ (triax vector sum; uncertainty K = 1.5 m/s²)
cutting wood 2.9 m/s²
✱
• The vibration emission level has been measured in
accordance with a standardised test given in EN 62841;
it may be used to compare one tool with another and as
a preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for different applications, or with different
or poorly maintained accessories, may significantly
increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may significantly
reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
14