Technical Data; Dust Extraction; Read And Follow All Safety Instructions - Milwaukee HEAVY DUTY AS-30 MAC Original Instructions Manual

TECHNICAL DATA

Volts
Mains frequency
Overload
Safety class
Type of protection
Total connected load
Power
IEC
Vacuum
Sound pressure level L IEC 60335-2-69
p
Uncertainty K=
Vibration emission value ahv IEC
60335-2-69
Tank volume
Suction hose diameter
Weight according EPTA-Procedure 01/2014
Power supply cord
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Instructions for use
The appliance must:
• only be used by persons, who have been instructed in its correct
usage and explicitly commissioned with the task of operating it
under supervision.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge.
• Children shall be supervised to make sure that they do not play
with the appliance.
• Do not use any unsafe work techniques.
•
•
following situations:
- Prior to cleaning and servicing
- Prior to replacing components
- Prior to changing over the appliance
- If foam develops or liquid emerges
Besides the operating instructions and the binding accident prevention
regulations valid in the country of use, observe recognised regulations
for safety and proper use.
trained within:
• use of the machine
• risks associated with the material to be picked up
• safe disposal of the picked up material

READ AND FOLLOW ALL SAFETY INSTRUCTIONS.

22

DUST EXTRACTION

230-240V
50 Hz
5 A
I
IP X4
2400 W
1200W
270 m 3 /h
250 hPa
67 dB(A)
2 dB(A)
< 2.5 m/s
2
30 l
1200 W
ø 36 mm
14,5 kg
H05RR-F3G1,5
Any other use is considered as improper use. The manufacturer
accepts no liability for any damage resulting from such use. The risk
for such use is borne solely by the user. Proper use also includes
manufacturer.
The safety label on the machine warns:
This appliance contains dust hazardous to health. Emptying and
maintenance operations, including removal of the dust collecting
means, must only be carried out by authorised personnel wearing
For dust extractors, ensure adquate air change rate H, when the
exhaust air is returned to the room. Observe national regulations
before use.
H = Q/V (1/h)
Where
V = room air volume
For Dust Class M machines (with type designation -2M) following
applies:
> 0.1 mg/m³
Dust Class M (IEC 60335-2-69). The dusts which belong to this class
are: dusts with OEL values > 0.1 mg/m³ as well as saw dust.
1)
The machine is tested in its entirety by vacuums for this dust class.
The maximum degree of permeability is 0.1% and the disposal must
be low dust.
Electrical connection
• It is recommended that the machine should be connected via a
residual current circuit breaker.
• Arrange the electrical parts (sockets, plugs and couplings) and lay
down the extension lead so that the protection class is maintained.
• Connectors and couplings of power supply cords and extension
leads must be watertight.
Important warnings
WARNING!
follow all safety instructions and caution markings before use. This
machine is designed to be safe when used for cleaning functions
parts, the machine and / or accessory should be repaired by a
competent service center or the manufacturer before use in order
user.
Do not leave the machine when it is plugged in. Unplug from the
socket when not in use and before maintenance.
Do not use with damaged cord or plug. To unplug grasp the plug,
not the cord. Do not handle plug or machine with wet hands. Turn
Do not pull or carry by cord, use cord as a handle, close a door on
cord, or pull cord around sharp edges or corners. Do not run
machine over cord. Keep cord away from heated surfaces.
= 20 m/s in the suction hose.
min
/h)
3
values
1)