Advertisement
Set
Not available
in all countries
ZK 100
Motor
ZK 7
part
Food chopper
ZK 200
Motor
ZK 3
ZK 7
part
Blender
Food chopper
ZK 300
Motor
ZK 3
ZK 7
MXK 4
part
Blender
Food chopper
Spice /
coffe mill
ZK 400
Motor
ZK 3
ZK 4
ZK 7
part
Blender
Slicer/
Food chopper
shredder
ZK 500
Motor
ZK 3
ZK 4
ZK 7
part
Blender
Slicer/
Food chopper
shredder
MX 40
Motor
KX 4
part
Glass blender
MX 44
Motor
KX 4
ZK 7
MXK 4
part
Glass blender
Food chopper
Spice/
coffee mill
MX 45
Motor
KX 4
ZK 7
KGZ 4
part
Glass blender
Food chopper
Meat
mincer
4
Additional attachments available
ZK 3
KX4
ZK 4
ZK 7
Blender
Glass
Slicer/
Food
blende
shredder
chopper
MXK 4
Spice/
coffee mill
MXK 4
Spice/
coffee mill
Caution!
Read all insructions carefully before using this
product.
KGZ 4
MXK 4
Meat
Spice/
Unwind the cord in the bottom of the basic unit
mincer
coffee mill
(motor part) entirely to avoid obstructing the
ventilation. Your voltage must correspond to the
voltage printed on the bottom of the basic unit
(motor part). Connect to alternating current (~) only.
When connecting to an outlet, the motor must
always be turned off (switch
appliance is constructed for normal household use
only. Please ensure that it is kept out of the reach of
children. Braun electric appliances meet applicable
safety standards. Repairs on electrical appliances
must only be done by authorized service personnel.
Faulty, unqualified repair work may cause accidents
or injury to the user.
Basic Unit (motor part)
Specifications
Voltage/wattage: see typeplate
on the bottom of the appliance.
Operating time and max. capacity: see processing
instructions.
Safety fuse
If the unit should stop – without an interruption in the
electrical power supply being the cause – check
!
whether the red lamp
The red lamp indicates that the electronic safety
fuse has been activated. In this case, turn the unit
off (switch set at «0») and wait for at least 15
minutes before turning the unit on again. If the
motor still will not start, is has not yet cooled off
sufficiently.
Turn the unit off again (switch set at «0») and wait
long enough for the motor to thoroughly cool off.
The unit will then start to run when switched on
again. Store the appliance after use only after
having turned it off, and pull the plug out of the
socket.
Description
!
Safety fuse lamp
"
Switch
$
Basic unit (motor part)
#
Safety lock
#
Safety lock
O = unlocked
For safety reasons, the motor can only be switched
on if the attachment has been locked properly.
"
Switch
0 = off
I = low speed
II = hight speed
IL = pulsator setting (low speed)
The switch does not catch at this setting;
it springs back to «0» (= off) as soon as it is
released.
"
at «0»). This
For safety reasons, the attachments can only be
unlocked if the switch is set at «0» (= off).
Cleaning
Always turn the motor off and pull the plug out of the
socket first. Clean the housing with a damp cloth
only. Never immerse into water.
Subject to change without notice.
This product conforms to the EMC-
Requirements as laid down by the Council
Directive 89/336/EEC.
Food Chopper
Attachment ZK 7
Caution!
When removing and replacing the blade insert
only take hold of it by the plastic shaft. The blades
is lit.
are very sharp! Do not reach into or underneath the
blades. The safety lock
part) must not be opened before the blade insert
has come to a rest. Do not operate the food chopper
attachment longer than 1 minute without
interruption. Allow the appliance to cool off for some
time after that.
Notice: When processing food with high power
consumption – e. g. 150 g prunes (approximately
750 W) – do not exceed an operating time of 15
seconds.
Description
1
Container
2
Blade insert
3
Lid
Assembling
• Set the switch
«0» (= off).
= locked
• Firmly place the container
• First put the blade insert
over the drive shaft as far as it will go, and then:
• put in the food you want to process.
Important: Do not put the blade insert in top of the
food.
2,
#
on the basic unit (motor
"
on the basic unit (motor part) to
1
on the basic unit.
2
into the container and
5
Advertisement
