Euro-Pro EP6312H Owner's Manual page 9

FAMILIARISEZ-VOUS AVEZ VOTRE ASPIRATEUR
1. Poignée
2. Bouton de verrouillage
3. Bouton 1 de relâche de la
coupelle
4. Poignée de la coupelle
5. Coupelle de récupération de
poussière
6. Surveille-filtre Intelli-Sense MC
7. Couvercle du filtre d'échappement
8. Brosse à planchers
9. Bouton de relâche de la brosse
à planchers
10. Boîtier principal
Spécifications Techniques
Tension: 120 V, 60 Hz
Demande de courant: 12 A
* Le produit actuel peut être différent de celui montré dans les illustrations.
11. Enrouleur de cordon
12. Bouton de l'enrouleur de cordon
13. Commutateur marche/arrêt
14. Boyau souple
15. Tube télescopique
16. Brosse à épousseter
17. Bouton de relâche du tube
télescopique
18. Suceur plat
19. Bouton 2 de relâche de la
coupelle
20. Pince de boyau souple
21. Bandoulière (non illustrée)
22
OPERATING INSTRUCTIONS
Please Note: The white pleated filter
material in the HEPA Filter will discolor
over time -This is NORMAL and will
NOT affect the performance of the filter.
If the HEPA Filter
is properly
Fig. A
"TapCleaned"
Wash
after each use
once a
and suction
month or
when
does not return
suction
to 100%, then
appears
we suggest that
reduced
the HEPA filter
Warning:
Allow 24
be "TapCleaned"
hours for drying before
vigorously until
replacing in unit.
no more dust
can be removed, then rinsed under the
faucet and allowed to dry for 24 hours
before refitting into the vacuum. (Fig. A)
This should be done once a month or
when suction appears to be reduced .
Caution
: The suction hole must
be open, free of any obstructions
at all times. Otherwise, the motor will
overheat and could become damaged.
Warning:
Always empty the dust
cup container and clean the HEPA
filter, Non-Woven Pre-Filter and Debris
Screen before each use and during
prolonged usage.
Never over fill the dust cup container -
remove dirt and clean the HEPA filter,
non-woven pre-filter and debris screen
when dirt in dust cup is at or below the
"MAX" level during prolonged usage or
risk motor damage.
If you wash the Hepa filter or the
non-woven pre-filter, make sure that
they have completely air dried
before inserting back in the
vacuum.
Please Note:
The HEPA Filter is
washable. It should, however, be
replaced every three (3) to six (6)
months to ensure peak performance of
your vacuum.
The non-woven pre-filter, pre-motor and
post motor filters are washable. They
should however be replaced every
three (3) months to ensure peak
performance of your vacuum.
Important: Make sure that ALL filters
have completely air dried before re-
installing back in the vacuum.
Changing & Cleaning the Pre-
Motor Filter
The pre-motor filter is a washable filter
but should be replaced every three (3)
months.
• Remove the dust cup container, the
Non-Woven Pre- Filter and the HEPA
filter to remove the pre-motor filter.
(Fig 13)
• Rinse the pre-motor filter in lukewarm
water and air dry the filter completely
for 24 hours. Do not use a washing
machine to rinse the filter.
Do not use a hair dryer to dry it. Air dry
only. Never operate the vacuum
without the pre-motor filter in place.
• When the filter is dry, replace into the
unit and replace the HEPA filter and
dust cup container.
• A severely soiled or clogged filter
should be thoroughly washed with
fresh tepid water. A mild detergent can
be used if required.
Pre-Motor
Filter
P
Fig. 13
Changing & Cleaning the Post
Motor Filter
The post motor filter is a washable filter but
should be replaced every three (3) months.
• Remove the filter cover from the front
of the unit and remove the filter. (Fig. 14)
• Rinse the post motor filter in lukewarm
water and air dry the filter completely
for 24 hours. Do not use a washing
machine to rinse the filter. Do not use a
hair dryer to dry it. Air dry only. Never
operate the vacuum without the post
motor filter in place.
• When the filter
is dry, replace
into the filter cover
and replace the filter
cover to the unit.
• A severely
soiled or clogged
filter should be
Fig. 14
thoroughly
washed with fresh tepid water. A mild
detergent can be used if required.
7