JVC TM-H1750CG Operating Instructions Manual page 7

HOW TO USE THE MENU
FUNCTIONS
(cont'd)
DISPLAY AND SELECTIONS IN THE <SET-UP
MENU> MODE (SETTING)
You can set the following set-up menu items.
• PICTURE SUB ADJ. • WHITE BALANCE
• H. POSITION • CONTROL LOCK
• V. POSITION • STATUS DISPLAY
Notes:
● Parameters for H. POSITION and V. POSITION can be set separately depending on
the signal (Input A (VIDEO), Input B (VIDEO), Input C or Input D) selected with the
input select buttons on the front panel.
Select the required video input with the input select buttons on the front panel in
advance.
● WHITE BALANCE can be set independently at 6500 or 9300 for the color temperature
value.
Set COLOR TEMP. to 6500 or 9300 on the <MENU> screen beforehand.
● INPUT REMOTE is shown when REMOTE SYSTEM is set to MAKE.
1. While pressing the MENU button, press the
CHROMA/PHASE button.
CHROMA MENU
The <SET-UP MENU> screen is displayed.
* The on-screen display goes off automatically after about five
minutes with operation performed.
PHASE
2. Press the CHROMA/PHASE or CONTRAST/BRIGHT
button to select the desired menu item.
A selection mark (4) is put next to the selected item.
CHROMA CONTRAST
Front panel Function
button displayed
PHASE BRIGHT
CHROMA/
PICTURE SUB ADJ.
PHASE
H. POSITION
CONTRAST/
V. POSITION
BRIGHT
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
3. Press the VOLUME/SELECT buttons to set.
VOLUME/SELECT
Front panel Function
button displayed
+
VOLUME/
4
SELECT (+)
CUTO
–
VOLUME/
1
SELECT (–)
DRV
Notes:
● For WHITE BALANCE items, select the CUT OFF or DRIVE
setting screen, then select the function display for adjustment.
● Press the EXIT (MENU) button to return to the <SET-UP
MENU> screen.
12
All manuals and user guides at all-guides.com
<SET-UP MENU> screen
1
• REMOTE SYSTEM
<SET-UP MENU>
• INPUT REMOTE
‰ PICTURE SUB ADJ.
H. POSITION
V. POSITION
WHITE BALANCE
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
2
EXIT
CHROMA CONTRAST VOLUME/SELECT
PHASE BRIGHT
<Front panel buttons>
1
Selection mark (4): Indicates the
menu item you select.
2
Menu item: Menu items you can
select.
3
Setting display: Indicates the
current settings (value).
4
Function display: The functions of
the front panel buttons (5 buttons
on the left) correspond to the
function displayed.
Function
Contents
displayed
Contents
Forward the menu item.
Reverse the menu item.
4
Forward selection mark ( )
– Lower the adjustment
value. (to the minimum)
4
Reverse selection mark ( )
+ Raise the adjustment
value. (to the maximum)
4
Forward the setting value.
1
Reverse the setting value.
Exit the <MENU>
EXIT
screen.
DRV Selects DRIVE adjustment.
Selects CUT OFF
CUTO
adjustment.
Contents
Adjusts red and blue
RB
signal level.
Increase (to max. value)
Adjusts red, green and
Forward the setting value
RGB
blue signal level.
Selects CUT OFF setting screen
Turns the ON-SCREEN
Decrease (to min. value)
display on or off. (This
Reverse the setting value
DISP function is effective only
Selects DRIVE setting screen
in the DRIVE or CUT OFF
adjustment mode.)
Set-up menu items
PICTURE SUB ADJ.
CONTRAST
BRIGHT
CHROMA
: 00
PHASE
: 00
H. POSITION
: OFF
: ON
: MAKE
: A – D
3
V. POSITION
4
WHITE BALANCE
DRIVE R. DRIVE
MENU
B. DRIVE
CUT OFF R. CUT OFF
G. CUT OFF
B. CUT OFF
CONTROL LOCK
STATUS DISPLAY
REMOTE SYSTEM
INPUT REMOTE
*1 May not be shown depending on the type of signals input.
*2 Refer to HOW TO USE EXTERNAL CONTROL on page 17 for more details.
4. To set the other set-up menu items, repeat the
procedures 2 and 3.
5. Press the MENU button to quit.
MENU
Note:
Setting Description
MAKE Make contact system: Controls the function with H and L (short-
circuits or opens 15th terminal (GND)).
TRG. Trigger system: Controls the function by short-circuiting (short-
circuits or opens 15th terminal (GND)) with pulse (about 1 sec.)
A-D Switches the input by short-circuiting a specified signal line in
INPUT A, B, C, or D.
A/B Switches between INPUT A and INPUT B with D-sub pin 2.
(Also, refer to HOW TO USE EXTERNAL CONTROL on page 17.)
Purpose
Image sub adjustment Selects CONTRAST/BRIGHT/CHROMA/PHASE. The
selected setting screen is shown. Select the function display for
adjustment.
Adjusts contrast. –10 –9 –01
• •
Adjusts brightness. –10 –9 –01
• •
–10 –9 –01
Adjusts color density. *1 • •
–10 –9 • • –01
Adjusts hue. *1
Adjusts the horizontal position of the
screen (+: Horizontal position shifts
–5 • • • –01
to the right/-: Horizontal position shifts to
the left)
Adjusts the vertical position of the screen
–5 • • • –01
(+: Vertical position moves up/-: Vertical
position moves down)
Adjusts the white balance. Selects the drive (DRV) or cut off (CUTO) adjustment. The selected
setting screen is shown. Select the function display for adjustment.
–20 –19
Adjusts red level. • •
–20 –19
Adjusts blue level. • •
–20 –19
Adjusts red cut off. • •
–20 –19
Adjusts green cut off. • •
–20 –19
Adjusts blue cut off. • •
Sets the operation buttons on the front
OFF ON
panel to control lock mode.
Sets the status display of the color system. OFF ON
MAKE TRG.
Sets the external control function method.
Sets external control of input selection.
(Shown only when REMOTE SYSTEM is A–D A/B
set to MAKE.)
Front panel Function
Contents
button displayed
Quit (or Release) the <MENU>
MENU EXIT
screen
Settings
+ 01 + 09 + 10
00 • •
+ 01 + 09 + 10
00 • •
+ 01 + 09 + 10
00 • •
00 + 01 • • + 09 + 10
00 + 1 • • • + 5
00 + 1 • • • + 5
–01 00 + 01 • • + 19 + 20
–01 00 + 01 • • + 19 + 20
–01 00 + 01 + 19 + 20
• •
–01 00 + 01 • • + 19 + 20
–01 00 + 01 • • + 19 + 20
*2
*2
Notes:
● When the CONTROL LOCK function is
set to ON, pressing operation buttons
on the front panel will display the
message "CONTROL LOCK ON!" on
the screen for about 3 seconds.
● The CONTROL LOCK function is
maintained even when the power is
turned off.
● To turn off the CONTROL LOCK
function, while holding the MENU button
press the CHROMA/PHASE button.
Then set the CONTROL LOCK function
to OFF.
● Even when the CONTROL LOCK
function is set to ON, the following
operations are available:
– Power Switch operation
– Volume control with the VOLUME/
SELECT buttons
– Display or disappear of the <SET-UP
MENU> screen.
● The STATUS DISPLAY function can be
set to display (ON) or not display (OFF)
the present color system when the
power is turned on or the input signal is
changed. Refer to page 9 for more
information.
● When REMOTE SYSTEM is set to
MAKE and any one of the INPUT A to D
buttons, the UNDER SCAN button,
COLOR OFF button or the ASPECT
button is pressed, "REMOTE ON!"
appears on screen for about 3 seconds.
(Not shown with CONTROL LOCK set
to ON.)
● When REMOTE SYSTEM is set to
TRG, the front panel controls can be
operated.
● INPUT REMOTE and REMOTE
SYSTEM are enabled when REMOTE
ENABLE is set to ON.
13