Troubleshooting; Technical Data; Service / Warranty - Flymo SimpliTrim Li Operator's Manual

v Do not clean with chemicals including petrol or solvents.
Some can destroy critical plastic parts.
The airflow slots must always be clean.
(8)
1. Clean the airflow slots with a soft brush (do not use a screwdriver).
2. Clean all movable parts after each operation. Especially remove any
grass and dirt from the protective cover
To clean the charging power supply:
Make sure that the contacts of the charging socket and the charging
power supply always are clean and dry before you connect the charging
power supply.
Do not use running water.
v Clean the contacts and the plastic parts with a soft and dry cloth.
5. STORAGE
To put into storage:
The product must be stored away from children.
1. Charge the battery.
2. Clean the trimmer and the charging power supply
(see 4. MAINTENANCE).
3. Store the trimmer and the charging power supply in a dry, enclosed
and frost­free place.
Disposal:
(in accordance with RL2012/19/EC)
The product must not be disposed of to normal household waste.
It must be disposed of in line with local environmental regulations.
The FLYMO battery contains lithium­ion cells that should
not be disposed of with normal household waste at the
end of its life.
IMPORTANT!
v Dispose of the product through or via your municipal recycling
collection centre.

6. TROUBLESHOOTING

DANGER! Risk of injury!
Cut injury when the product starts accidentally.
v Wait for the plastic blade to stop before you troubleshoot
the product.
To replace the plastic blade [ Fig. T1 / T2 ]:
DANGER! Risk of cutting injuries!
v Do not use metal cutting elements or spare parts and
acces sories not intended for use by FLYMO.
The plastic blades may only become worn to half the original
length at most. Only use original FLYMO Spare Blades FLY083.
Spare plastic blades are available from your FLYMO dealer or
direct from FLYMO Service.
• FLYMO Spare Blades for SimpliTrim Li FLY083 – PNC 598523101
To remove the plastic blade:
1. Turn the trimmer over.
2. Push the end of the plastic blade down slightly (A), slide the plastic
(3)
blade inside through the blade carrier
To insert the plastic blade:
v Slide the new plastic blade (3)
(9)
the blade carrier until it audibly engages (click).
When the new plastic blade is correctly inserted, it can be moved more
easily.
Problem Possible Cause
Trimmer is not cutting Plastic blade is worn or too
cleanly or not cutting at all short.
Plastic blade is broken off.
Trimmer vibrates severely Plastic blade is excessively
worn and creates an unbalance.
Blade carrier is worn.
6
(4)
.
Li-ion
(9)
(B) and pull out.
from inside through the slot in metal of
Remedy
v Replace the plastic blade.
v Replace the plastic blade.
v Replace the plastic blade.
v Replace the blade carrier.
Problem Possible Cause
Trimmer does not start. Under voltage.
Charging control lamp ;
flashes green
Trimmer does not start.
Battery overload.
;
Charging control lamp
flashes red
Engine is blocked.
Battery temperature is out of
range.
(Lc)
Power LED on the
Charging power supply is not
charging power supply plugged in correctly.
does not illuminate
NOTE: For any other malfunctions please contact the FLYMO service depart-
ment. Repairs must only be done by FLYMO service departments or specialist
dealers approved by FLYMO.

7. TECHNICAL DATA

Battery Trimmer Unit
Cutting width cm
Rpm of blade carrier R/min.
Weight kg
Sound pressure level L
1)
dB(A)
pA
Uncertainty k
pA
Sound power level L :
2)
WA
measured/guaranteed
dB(A)
Uncertainty k
WA
Hand/arm vibration a
1)
m/s
2
vhw
Uncertainty k
a
Measuring process complying with: EN 50636-2-91
1)
NOTE: The stated vibration emission value has been measured according to
a standardized test procedure and can be used for comparison of one electric
power tool with another. It can also be used for preliminary evaluation of
exposure. The vibration emission value can vary during actual use of the electric power
tool.
Battery Unit
Battery voltage V (DC)
Battery capacity Ah
Battery charging time
min.
80 % / 100 % (approx.)
Charging Power Supply Unit
Mains voltage V (AC)
Mains frequency Hz
Rated Power W
Output voltage V (DC)
Max. output current mA
8. ACCESSORIES
FLYMO Charging Power Charger to charge the internal batteries.
Supply
FLYMO Spare Blades for As replacement for consumed plastic blades.
SimpliTrim Li

9. SERVICE / WARRANTY

Service:
Please contact the address on the back page.
Warranty statement:
In the event of a warranty claim, no charge is levied to you for the services
provided.
Husqvarna UK Ltd. grants a warranty for all original FLYMO new products
for two years from the date of original purchase from the retailer, provided
Remedy
v Charge the battery.
v Release the start lever.
Start again.
v Remove the obstacle.
Start again.
v Use the battery in surround-
ings where temperatures are
between 0 °C and 40 °C.
v Plug the charging power
supply into a wall outlet.
Value (PNC 967986101)
23
9500
1.7
70
2.5
84 / 88
4
< 2.5
1.5
RL 2000/14/EC
2)
Value
14.4
2.0
160 / 200
Value (PNC 598446701)
100 – 240
50 – 60
15
18.5
600
PNC 598446701
Art. FLY083
PNC: 598523101