Bpt LINEAKIT Series Quick Start Manual page 5

SW2
SW1
XC/310 receiver, or by means of PCS/300 by selec-
ting the corresponding receiver.
Programming melodies and number of rings
To enter programming mode, lift the receiver and
press the button underneath A (fig. 6) 5 times,
within 5 s.
A short audible signal sounds to confirm you have
entered programming mode (you automatically enter
the entry panel call melody programming procedure).
To repeat the procedure to enter programming
mode, hang up and wait at least 5 s.
Press the door lock release button to run through
the different modes in sequence.
A number of short audible signals sound to indica-
te that you have entered the corresponding mode:
no. 1 audible signal: programming of melody asso-
ciated with the call from the entry panel.
no. 2 audible signals: programming of melody asso-
ciated with doorbell.
no. 3 audible signals: programming of number of
rings announcing a call.
1 - Programming of melody associated with the call
from the entry panel
The first entry panel call melody is played repea-
tedly, alternated with a short audible signal.
To listen to the next melody, press the auxiliary but-
ton 2 ( ) during the pause between the audible
signal and melody.
Repeat the operation until you hear the melody you
want.
P1
To save the new setting without programming
anything else, hang up; otherwise, press the door
lock release button to call up the next programming
procedure.
2 - Programming of melody associated with doorbell
The first doorbell melody is played repeatedly, alter-
nated with two short audible signals.
To listen to the next melody, press the auxiliary but-
ton 2 ( ) during the pause between the audible
signal and melody.
Repeat the operation until you hear the melody you
want.
16
To save the new setting without programming
anything else, hang up; otherwise, press the door
lock release button to call up the next programming
procedure.
3 - Programming of number of rings announcing a call
Three short audible signals sound.
Decide how many rings you want and press the
auxiliary button 2 (
times (in the range 1 to 6).
In system 300 installations, you can increase the
number of rings to a maximum of 51 by customizing
control unit XA/300LR.
3 s after the button was last pressed, you will hear
the call selected for the chosen number of rings.
If you want to save settings without programming
anything else, hang up; otherwise, press the door
lock release button to enter the entry panel call
melody programming procedure again.
NOTE. When you exit programming mode, the last
settings selected for each programming procedure
are saved.
17
For a setting to be taken as selected, you must have
heard it at least once.
Function of each terminal (fig. 10)
Terminal block M1
power supply local
from 12÷16 V AC or 14÷18 V DC
B X1 line
+
doorbell input
–
Terminal block M2
connection for
YAL loudspeake
Function of connectors
CN1 (position A) for YP3 accessory: pushbuttons
are used to make intercom calls from 1 to 3 (or for
auxiliary functions from 3 to 5).
CN2 (position B) for YP3 accessory: pushbuttons
are used to make intercom calls from 4 to 6 (or for
auxiliary functions from 6 to 8).
CN3 for YPL accessory.
18
CN4 for YV or YVC monitor.
Technical features
• Supply voltage: local 12 to 16 V AC or 14 to 18 V
DC, centralized 14 to 18 V DC.
• Power supply from bus: 15÷20 V DC.
• Current demand without monitor module: 100 mA
max. (<1 mA quiescent).
• Number of receivers activated at the same time
by X1 BUS: 1.
• Maximum number of receivers that can be con-
nected to control unit XA/300LR: 100 without YPL.
• Maximum number of receivers that can be con-
nected to an X1 entry panel: 64 without YPL (100
with XAS/301).
• X1 connection line: non polarized twisted pair
Z=100 Ω.
• Working temperature range: 0 °C to +35 °C.
WARNING. In installations with XA/300LR we
recommend you gather up the receiver's ID (SN)
codes, applied on the outside of the housing, and
enter them in the tables that come with the
XA/300LR, MPP/300LR and IPC/300LR.
) the corresponding number of
YV MONITOR MODULE
It is equipped with the following controls:
Brightness
Contrast
Technical features
• CCIR (EIA) standard.
• Picture screen: 4" (10 cm).
• Current demand: 350 mA max.
• Bandwidth response at -3 dB: 5 MHz.
• Horizontal frequency: 15,625 Hz (15,750 Hz EIA).
• Vertical frequency: 50 Hz (60 Hz EIA).
• Working temperature range: from 0 °C to +35 °C.
YVC MONITOR MODULE
It is equipped with the following controls:
Brightness
Saturation colour
Technical features
• PAL standard.
• Display: 3,5" LCD colour, active matrix.
• Current demand: 360 mA max.
• Working temperature range: from 0 °C to +35 °C.
VIDEO ENTRY PANEL HEV/301
Single-button video entry panel for managing the
whole installation.
Teamed with button plates HEP/306-HEP/312D,
installations with up to 64 users can be set up.
For connections to user extensions the entry panel
uses BPT X1 TECHNOLOGY bus connection, ena-
bling all signals involved in installation to be sent
along a telephone-type single twisted pair line.
An additional three video-entry or audio-only entry
panels can be added to the first in series without
the need for other equipment (selectors, distribu-
tors).
The entry panel comes ready to house the KHSO
luminous system busy warning kit and 1 KHPS (or 1
KHPD) call kit.
The entry panel comes complete with:
- CCD camera with ±11° manual angle adjustment
both horizontally and vertically (fig. 14), with fixed-
focus lens (see fig. 15 for dimensions of the target
area);
- phonic unit;
- infrared LED for lighting the target area;
- three potentiometers for the following functions
(fig. 14-16):
volume control at entry panel;
volume control at receiver;
P1 timed (in the range 1 to 15 s) solenoid door-lock
release.
The entry panel comes with system busy and door-
lock release buzzer.
The wires supplied make it simple to connect the
entry panel's various component units.
Function of each terminal
14-18V DC
power supply
solenoid lock output
door-lock release button
– earth for solenoid lock
auxiliary command 1 output
auxiliary command 2 output
entry panel enabling output
bus input from
B IN
other entry panels
bus output towards receivers or other entry
B OUT
panels
Connector functions
5-pin CN1 connector: used for connection to entry
panel HEP/306 or HEP/312D.
3-pin CN3 connector: used for connection to but-
tons KHPS or KHPD.
1-red: to button n° 2.
2-orange: to button n° 3.
3-yellow: to button n° 4.
WARNING. In installations with a number of entry
panels, call buttons must be arranged in the same
order on each.
Connector CN4: comes ready connected.
1-black: to button no. 1.
2-brown: to button no. 1.
5