Page 1 Produced under a license from Northrop Grumman Systems Corporation. F-14D Super Tomcat, F-5E Tiger II, A-10A Thunderbolt II, B-2A Spirit, and CVN-65 Enterprise are trademarks of Northrop Grumman Systems Corp. and are used under a license to Sega Corporation.
Page 2 BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: To maintain safety: To ensure the safe operation of this product, be sure to read the following before usage. The following instructions are intended for the users, operators and the personnel in charge of the operation of the product.
Page 3 SEGA. INSPECTIONS IMMEDIATELY AFTER TRANSPORTING THE PRODUCT TO THE LOCATION Normally, at the time of shipment, SEGA products are in a status allowing for usage immediately after transporting to the location. Nevertheless, an irregular situation may occur during transportation.
Page 4: Table Of Contents
TABLE OF CONTENTS BEFORE USING THE PRODUCT, BE SURE TO READ THE FOLLOWING: TABLE OF CONTENTS INTRODUCTION HANDLING PRECAUTIONS ................. 1 PRECAUTIONS REGARDING INSTALLATION LOCATION ........5 2-1 LIMITATIONS OF USAGE ....................5 2-2 OPERATION AREA ......................6 PRECAUTIONS REGARDING PRODUCT OPERATION ......8 3-1 BEFORE OPERATION .....................8 3-2 DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) ........11 PART DESCRIPTIONS ................
Page 5 CONTROL STICK ..................98 11-1 HOW TO REMOVE CONTROL STICK .................99 11-2 GREASING .........................103 11-3 VOLUME REPLACEMENT ..................104 11-4 MICROSWITCH REPLACEMENT ................108 11-5 GUIDE PLATE REPLACEMENT ................110 THROTTLE LEVER ................... 111 12-1 GREASING .........................112 12-2 VOLUME ADJUSTMENT OR REPLACEMENT ............114 ROLL VOLUME ..................
Page 6: Introduction
This manual is intended to provide detailed descriptions together with all the necessary information covering the general operation of electronic assemblies, electro-mechanicals, servicing control, spare parts, etc. for the product, “AFTER BURNER CLIMAX.” This manual is intended for the owners, personnel and managers in charge of operation of the product.
Page 7 Customers using this product who wish to obtain this source code should enter the following password on the website below to download it. URL: http: //amproduct-softlicense.sega.jp/ ID: amsoftwebdl Password: segaamhd1 GPL/LGPL Contract Site URL: http: //www.fsf.org/licenses/gpl.html...
Page 8 Definition of ‘Site Maintenance Personnel or Other Qualified Individuals’ Procedures not described in this manual or marked as 'to be carried out by site maintenance personnel or other qualified professionals' should not be carried out by personnel without the necessary skill or technology. Work carried out by unqualified persons may cause serious accidents, including electrocution.
Page 9: Handling Precautions
• Be sure to perform grounding appropriately. Inappropriate grounding can cause an electric shock. • Be sure to use fuses meeting the specified rating. Using fuses exceeding the specified rating can cause a fire or an electric shock. • Be sure that connections such as IC BD are made properly. Insufficient insertion can cause an electric shock. • Specification changes, removal of equipment, conversion and/or addition, not designated by SEGA are not permitted. - Failure to observe this may cause a fire or an electric shock. Non-compliance with this instruction can have a bad influence upon physical conditions of the players or the onlookers, or result in injury during play. - SEGA shall not be held responsible for damage, compensation for damage to a third party, caused by specification changes not designated by SEGA. • Be sure to perform periodic maintenance inspections herein stated.
Page 10 • For the IC board circuit inspections, only the logic tester is allowed. The use of a multiple-purpose tester is not permitted, so be careful in this regard. • When cleaning the CRT surfaces, use a soft and dry cloth. Do not apply chemicals such as thinner, benzine, etc. • Static electricity from your body may damage some electronics devices on the IC board. Before handling the IC board, touch a grounded metallic surface so that the static electricity can be discharged. • Some parts are not designed and manufactured specifically for this game machine. The manufacturers may discontinue, or change the specifications of such general-purpose parts. If this is the case, SEGA cannot repair or replace a failed game machine whether or not a warranty period has expired.
Page 11 CONCERNING THE STICKER DISPLAY This SEGA product has stickers attached describing the product manufacture No. (Serial No.) and Electrical Specifications. It also has a Sticker describing where to contact for repair and for purchasing parts. When inquiring about or asking for repairs, mention the Serial No. and Name of Machine indicated on the Sticker.
Page 12 FIG. 1b FIG. 1d FIG. 1c...
Page 13: Precautions Regarding Installation Location
PRECAUTIONS REGARDING INSTALLATION LOCATION This product is an indoor game machine. Do not install it outside. Even indoors, avoid installing in places mentioned below so as not to cause a fire, electric shock, injury and/or malfunction. - Places subject to rain or water leakage, or places subject to high humidity in the proximity of an indoor swimming pool and/or shower, etc. - Places subject to direct sunlight, or places subject to high temperatures in the proximity of heating units, etc. - Places filled with inflammable gas or vicinity of highly inflammable/volatile chemicals or hazardous matter.
Page 14: Operation Area
MAX. 6.30 A (AC 120 V, 60 Hz) - OPERATION AREA • For the operation of this machine, secure a minimum area of 2.1 m (W) x 2.18 m (D). The dimensions of the base periphery are established in consideration of ventilation, maintenance and customer passage. With this product there is the danger that someone could fall down while getting onto the base or the seat. And if they fall and hit their head, there could be a very serious injury. Be sure to always secure enough space as prescribed in this manual. • Be sure to provide sufficient space specified in this manual. Do not allow objects to block the ventilation ports. It can cause generation of heat and a fire. • SEGA shall not be held responsible for damage or compensation for damage to a third party, resulting from the failure to observe this instruction. • If the machine does not fit through the entryway to the installation location, do not disassemble it without first consulting the instructions. The machine should only be disassembled in accordance with the instructions listed in this manual; do not attempt to disassemble it in any other way. Specific tools and adjustment procedures are required to assemble and disassemble the mechanical parts. Attempting to assemble or disassemble the machine without consulting the instructions may result in accidents during assembly/disassembly and electric shock, short circuits, and/or personal injury during operation. If the machine still does not fit through the entryway after following the procedures in this manual, contact your retailer or the office listed in this manual.
Page 15 Under normal operation, the space on the left side as you face the monitor can be 0.25 m in width. However, when performing routine maintenance once every 6 months or year after installation, secure at least 0.7 m of space. Without adequate space, work cannot be performed properly. (mm) FIG. 2 Installation and operation area...
Page 16: Precautions Regarding Product Operation
PRECAUTIONS REGARDING PRODUCT OPERATION To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players. -1 BEFORE OPERATION In order to avoid accidents, check the following before starting the operation: • To ensure maximum safety for the players and the customers, ensure that where the product is operated has sufficient lighting to allow any warnings to be read. Operation under insufficient lighting can cause bodily contact with each other, hitting accident, and/or trouble between customers. • Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can have a bad influence upon the players' or the customers' physical conditions.
Page 17 • Do not climb on the product. Climbing on the product can cause falling down accidents. To check the top portion of the product, use a step ladder. • To avoid electric shock, check to see if door & cover parts are damaged or omitted. • To avoid electric shock, short circuit and/or parts damage, do not put the following items on or in the periphery of the product. Flower vases, flowerpots, cups, water tanks, cosmetics, and receptacles/ containers/vessels containing chemicals and water.
Page 18 • To avoid injury, be sure to provide sufficient space by considering the potentially crowded situation at the installation location. Insufficient installation space can cause making bodily contact with each other, hitting accidents, and/or trouble between customers. • Check the control devices to make sure that there are no scratches or cracks on parts touched by players, as such defects can cause injury to hands and fingers.
Page 19: During Operation (Paying Attention To Customers)
- DURING OPERATION (PAYING ATTENTION TO CUSTOMERS) To avoid injury and trouble, be sure to pay attention to the behavior of visitors and players. • For safety reasons, do not allow any of the following people to play the game. - Those who have high blood pressure or a heart problem. - Those who have experienced muscle convulsion or loss of consciousness when playing video games, etc. - Those who have neck or spinal cord problems.
Page 20 • Playing the game without first s e c u r i n g t h e s e a t b e l t m a y cause customers to fall out. Customers should be instructed always to secure themselves with the seatbelt before playing the game.
Page 21 • Customers should be warned not to place children on their laps while they play the game. Doing so may cause the child to become trapped between the player and the control panel and/or cause the machine to tip over. • Persons other than the player should not be allowed to approach the machine while the seat is in motion. Such actions m a y r e s u l t i n s i d e s w i p i n g a n d / o r collision accidents. The safety sensor is only able to detect foreign objects on top of the base. Young children are...
Page 22 • Immediately stop such violent acts as hitting and kicking the product. Such violent acts can cause parts damage or falling down, resulting in injury due to fragments and falling down. • When entering or exiting the machine, players may trip over the base. Be sure to warn players who do not appear to be exercising proper caution. • Persons other than the player should not be allowed to touch the controls during play. They may brush against or collide with the controls or the player, possibly resulting in accidents. • Players should be warned not to place personal effects or other objects on the base of the machine. If the safety sensor fails to detect these items, the motion of the machine may cause them to fly out and strike other customers. • This product has a player weight restriction of 150 kg. This restriction is in place, because, if weight exceeds 150 kg, there could be an accident as a result of faulty operations or parts damage.
Page 23: Part Descriptions
PART DESCRIPTIONS FIG. 4 Overall View Dimensions Required for Installing Each Unit (Width x Length x Height) (Weight) Cabinet 1,225 mm x 1,810 mm x 1,900 mm 429 kg Billboard 660 mm x 510 mm x 270 mm 11 kg Finished cabinet 1,225 mm x 1,810 mm x 1,980 mm 440 kg...
Page 24: Accessories
ACCESSORIES Confirm that the accessories listed in the table below are present when setting up the product. Accessories marked “Spare” in the note column are consumable items but included as spares. TABLE 5a OWNER’S MANUAL LINDBERGH SERVICE MANUAL MASTER KEY 420-6955-02 (1) 420-6921-01 (1) 220-5793-2-A001 (2)
Page 25 The parts listed in Table 5b are packaged separately, but they must always be attached when using the product. They are attached while assembling and installing the product. TABLE 5b POWER CABLE 600-7326 (1) For installation, see 6-4. The DVD software kit, DVD DRIVE and DVD wire are sold separately but they are required for installing the product’s software.
Page 26 TABLE 5d XKT-1515-01: DVD DRIVE KIT FOR LBG ENG SERVICE MANUAL 420-6923-01 (1) DVD DRIVE 610-0719-01-91 (1) For software installation, see chapter 6 3 . DVD WIRE 605-0094 (1) For software installation, see chapter 6 3 .
Page 27: Assembly And Installation
ASSEMBLY AND INSTALLATION • Perform assembly work by following the procedure herein stated. Failure to comply with the instructions can cause electric shock. • Perform assembling as per this manual. Since this is a complex machine, incorrect assembling can cause an electric shock, machine damage and/or improper functioning as per specified performance. • When assembling, more than one person is required. Depending on the assembly work, there are some cases in which working by one person alone can cause personal injury or parts damage.
Page 28 • The cabinet has ventilation ports. Be sure not to block them. If they are blocked, heat can build up, leading to fire. This can also accelerate wearing of parts and malfunctions. • Secure ample ventilation space around the cabinet. If heat builds up, there could be accidents associated with heat or smoke generation. • If two cabinets are installed in alignment, make sure that there is ample distance between them so that players or other customers will not come in contact or collide with each other. If the distance is too narrow, there could be contacts or collisions. If someone should fall down, head injury or other serious accident could occur. Trouble between customers could also arise.
Page 29 Installation and assembly of this product should take place in the following sequence. FIXATION TO INSTALLATION SITE ATTACHMENT OF BILLBOARD PREPARATION FOR INSTALLATION CONNECTION OF POWER AND GROUND ENGAGEMENT OF POWER SUPPLY AND SOFTWARE INSTALLATION ENGAGEMENT OF POWER SUPPLY AFTER INSTALLING SOFTWARE CONFIRMATION OF ASSEMBLY Essential tools - Philips screwdriver (for M4 screws)
Page 30 FIXATION TO INSTALLATION SITE Make sure that all the adjusters contact the floor. Otherwise the cabinet could move, causing an accident. The product comes with casters attached at 6 locations and adjusters at 4 locations (Fig. 6-1a). When the installation site has been determined, have the adjusters come in direct contact with the floor. Establish a gap of about 5 mm between the floor and the casters and adjust the unit so that it will remain level.
Page 31 FIG. 6-1c Three Surface Views FIG. 6-1d Ventilation Space Views are reduced to 1/100. Use When installing the product next to a wall or other them for reference in installation game unit, where customers will not be able to pass, site layout.
Page 32 ATTACHMENT OF BILLBOARD The billboard contains fluorescent lamps and wires. If it is not handled carefully, the lamps might crack and the wires could be damaged. FIG. 6-2a Billboard Remove billboard lid from billboard rear surface. Remove the 4 truss screws. After the billboard has been attached, attach the billboard lid and 4 truss screws to the billboard rear surface.
Page 33 Place the billboard on top of the monitor. Place it from the side of the CRT. Insert the bottom of the billboard into the bracket on the monitor top plate. Have the front and rear of the billboard each held by a separate worker while proceeding.
Page 34 Secure billboard in place with 4 hexagonal bolts. Use a flat washer with each hexagonal bolt with spring washer attached. FIG. 6-2g Connect the two billboard wire connectors to the connectors on the monitor top plate. FIG. 6-2h Attach billboard lid and secure it in place with 4 truss screws. FIG.
Page 35 PREPARATION FOR INSTALLATION • When connecting the DVD wire connector, check the orientation carefully and connect securely. The connector must be connected in the proper direction. If it is connected in the wrong direction or indiscriminately at an incline so that a load is applied, the connector or its terminal pins could break, causing a short circuit or fire. • Be careful not to damage the DVD wire by getting it caught between objects, etc. Doing so may cause a short circuit or fire. • Connect the DVD DRIVE to the LINDBERGH before connecting the power. Adhere strictly to the proper sequence in performing work. Failing to do so may cause electrical shock or short circuit. Have on hand the DVD software kit, DVD DRIVE and DVD wire, all of which are sold separately. In preparation for software installation, connect the LINDBERGH in the base to the DVD DRIVE with DVD wire. Remove the 2 truss screws holding the base rear door R.
Page 36 There is a wooden base mounted with the LINDBERGH inside the rear door R. Remove the cable lid attached to the base bottom plate inside the slot of the wooden base handle. Remove the 2 flange nuts. After the cable lid has been removed, you will find a hole for passing the DVD wire. FIG.
Page 37 Remove the key chip from the DVD kit case and insert it into the LINDBERGH. Make sure it is inserted in the proper direction. (In the photo, two connectors have been removed from the LINDBERGH so that the key chip can be seen. In practice, these connectors are not removed.) FIG.
Page 38 CONNECTION OF POWER AND GROUND • Use the power supply equipped with an earth leakage breaker. Use of power supply without such a breaker could result in fire if there is a current leakage. • Have available a securely grounded indoor ground terminal. Without proper grounding, customers could be electrocuted and product operations might not always be stable. • Do not expose the power cord. If these are exposed, customers could stumble over them, for instance, and easily damage them. Additionally, if these lines are damaged, there could be a risk of electrical shock or short circuit. Set these lines at locations where they will not interfere with customer traffic, or attach covers to them.
Page 39 There is an AC unit on the base side opposite the monitor (CRT). This AC unit contains the following. - Main switch - Inlet for power cable connection - Circuit protector The accessory power cord has a ground wire inside it. Connect the power cord to the AC unit then insert the power cord plug into a “power outlet with ground terminal.”...
Page 40 Fully insert the power cord connector on the side opposite the power plug into the AC unit inlet. Fully insert the power cord plug into the outlet. The power cord is laid out indoors. Protect the power cord by attaching wire cover to it. FIG.
Page 41 ENGAGEMENT OF POWER SUPPLY AND SOFTWARE INSTALLATION • When the software is installed, the seat moves left and right automatically. First make sure no one is near the product, then engage the power. If someone is near the product, they could come in contact with it or collide with it, get their hand or finger caught somewhere, or accidentally fall down. • Be careful not to damage the DVD wire by getting it caught between objects, etc. Doing so may cause a short circuit or fire. • The following explanation assumes that the product has been assembled properly as explained above. If there is an error or if the product operates in a manner other than as indicated below, cut off the power supply immediately. Failure to do so may result in a fire or electrical shock. • If you look directly at the laser beam in the DVD DRIVE, you could suffer vision impairment. Do not look inside the DVD DRIVE. • The software is not installed on the game board (LINDBERGH) when the power supply is engaged, so the “Error 22” message is not a malfunction. However, if there is another error display, or if there is no video output at all, there might have been an error in product assembly, wiring connections might be faulty, or the LINDBERGH might not be functioning properly.
Page 42 Have available a DVD kit, which is sold separately. (See Table 5c.) Before engaging the power supply, be sure that no one is on the base and that there are no tools, etc., on the seat. When the product is shipped from the factory, the software has not yet been installed. But when the software is installed and the power supply is engaged, the seat will move left and right.
Page 43 Press the DVD DRIVE switch. The tray goes back into the drive. Make sure no one is near the product, and then re-engage the power. Turn the main switch to OFF once, wait for at least one minute, then turn the switch back to ON. Software is installed automatically from the DVD to the LINDBERGH.
Page 44 ENGAGEMENT OF POWER SUPPLY AFTER INSTALLING SOFTWARE Only engage the power supply after checking the surroundings. Initialization takes place automatically when engaging the power supply after software installation. At this time the seat will move, and if anyone is near the product, they may collide with the product, fall down, or get their hand or finger caught somewhere. It takes about 2 minutes and 30 seconds for initialization to complete after the power has been engaged. Do not touch the product or press any buttons until after initialization is completed. If an anomaly is detected during initialization, there is an error display. Unless the cause of the error is removed and initialization is allowed to complete normally, the product will not operate properly.
Page 45 If the seat stops at an incline after re-executing initialization, there might be a defective volume setting or other problem. Use the test mode to check numerical settings. Even when the power source has been cut off, credit count and ranking data are kept stored in the product. However, fractional coin counts (inserted coins that do not amount to one credit) and bonus counts are not kept.
Page 46 CONFIRMATION OF ASSEMBLY Use test mode to confirm that assembly is proper, and that the LINDBERGH, connecting boards, and input/output devices are normal. Perform the following tests in test mode. For tests (1) to (4), refer to the LINDBERGH service manual. For tests (5) to (7), see [9-3 Game Test Mode]. The items displayed on the test screen for tests (5) and (6) vary depending on the setting for cabinet type in the game setting screen.
Page 47 (6) Output Test When “OUTPUT TEST” has been selected on the game test mode menu, the screen for testing lamps and other output devices appears. If each output device operates properly, the output device and its wiring connections are normal. FIG.
Page 48: Precautions When Moving The Machine
PRECAUTIONS WHEN MOVING THE MACHINE • Always disconnect the power cable before moving the product. If it is moved with the power cable connected, the cable could be damaged, causing fire or electric shock. • To move the unit over the floor, pull in the adjustors and have the casters contact the floor. While moving the unit, be careful that the casters do not roll over the power cord or the ground wire. If cord or wire is damaged, there could be electrical shocks and/or short circuits. • To lift up the cabinet, hold it at the bottom. If you hold it anywhere else, the weight of the cabinet could cause damage to parts or attachments, resulting in injury.
Page 49: Moving The Machine
-1 MOVING THE MACHINE FIG. 7-1a • Observe the following precautions when moving the machine. Failure to observe these precautions may result in damage to the casters and/or the flooring. - The machine should be moved along a level floor. - Ramps should be used to climb/descend steps 1 cm or greater in height. - The machine should not be moved any faster than walking speed (about 2 km/h). - The machine should not be tilted too far to one side or loaded excessively on one side only. • If the entrance is narrow or low and the product must be laid down sideways, or if the product must be disassembled in a manner not described in this manual, contact the office given in this manual or the point of purchase. If the product...
Page 50 FIG. 7-1b...
Page 51 Precautions in Moving Loads • This product weighs over 400 kg. It cannot be lifted by human strength alone. Trying to do so could cause accidents. Use a crane or other powered hauling unit to move the product. • When moving a load, insert buffer material between the base and the platform wall and attach the product securely to the platform with rope or other means. If exterior parts are damaged or deformed, there could be electrical shocks and/ or short circuits. • A minimum of 8 persons is needed to load this machine onto a forklift truck. The procedure cannot be carried out safely with fewer than this number. • The forklift should have a platform of at least 1,500 mm in length. The procedure cannot be carried out safely with a platform shorter than this. • When using a crane to move this machine, ensure that the person operating the crane is properly qualified. Do not attempt to carry out this procedure without properly qualified personnel. • Always remove the billboard before moving the product. If the billboard hinders loading operations or collides with the platform, etc., there could be accidents. • Do not push or support the monitor, control stick, throttle lever or plastic components while moving or loading the product. Otherwise these components could be damaged, resulting in injuries from fragments, cracks, etc.
Page 52 FIG. 7-1c Precautions when securing with rope FIG. 7-1d Precautions in securing platform...
Page 53: Transport When Entrance Is Narrow Or Low
- TRANSPORT WHEN ENTRANCE IS NARROW OR LOW If you remove door or air vent and leave the interior exposed while moving the unit, exercise ample caution. Be careful that no foreign objects get inside the machine, and do not press or hold interior parts or wires. If foreign objects get in, or if internal parts or wires are damaged, there could be electrical shocks and/or short circuits. Before removing guard pipe or handgrip, hold the pipe or grip firmly, then remove fastening bolts or screws. If pipe or grip falls over or drops after bolts or screws have been removed, there could be accidents.
Page 54 Remove the 8 hexagon bolts from guard pipes L and R at the right and left of the base. Hold up the guard pipe securely when removing bolts. The 2 bolts at the rear are different in length than the other 6 bolts. A flat washer and spring washer are used with hexagon bolts.
Page 55 Unlock with the master key and remove the rear doors. FIG. 7-2e There is an air vent only on the left side of the base. Remove the 4 truss screws that hold it down. FIG. 7-2f Remove the air vent. FIG.
Page 56 Remove the 3 hexagon socket screws that hold down the L and R handgrips at the top left and right of the monitor. Hold the handgrip securely when removing hexagon socket screws. Use a 5 mm Allen wrench or Allen screwdriver. FIG.
Page 57: Game Description
GAME DESCRIPTION The following explanations apply when the product is functioning satisfactorily. Should there be any actions different from the following contents, some sort of faults may have occurred. Immediately look into the cause of the fault and eliminate the cause thereof to ensure satisfactory operation. Normally, when the power is on, the fluorescent lamp in the billboard on the monitor and the two fluorescent lamps on the seat rear surface are lit up.
Page 58 FIG. 8b FIG. 8c...
Page 59 Game Outline - AFTER BURNER CLIMAX is a flight shooting game that features exhilarating gameplay. - The player takes on the role of the leader of the “Brave Fangs”, a special air-force unit whose mission is to prevent the outbreak of all-out nuclear war.
Page 60 Game Mode Select (Network Play only) Move the control stick left/right to select a game mode. Pull the trigger or press the START button to confirm selection. ONE-PLAYER Mode: Play for one player. FIG. 8e MODE SELECT Screen TWO-PLAYER Mode: Two players play at the same time.
Page 61 Stage Composition FIG. 8g Stage Composition There are a total of 21 stages. - There are 17 basic stages (shown in squares on the above diagram) - There are 2 secret stages (stages 06S and 10S on the above diagram) - There are 2 extra stages (stages 14 and 15 on the above diagram) Some stages simply have a number, like “01”, and some also have a letter included, like “04A”.
Page 62 Controls FIG. 8h Throttle Lever FIG. 8i Control Stick The player aircraft is controlled by the “Throttle Lever” and “Control Stick”. <Throttle Lever> Used to change the speed of the player aircraft. Pull the lever towards you to decrease speed. Push the lever away from you to increase speed. Push the lever all the way away from you to activate CLIMAX Mode.
Page 63 <Game Rules> Either clearing all the stages, or all the player aircraft being lost results in Game Over. All the player aircraft have been lost when there are no remaining player aircraft and the armor gauge falls to 0%. When an aircraft’s armor gauge falls to 0%, that aircraft is lost, and the remaining player aircraft are reduced by one. During game play, there are no increases in the number of aircraft and no restoration of the armor gauge.
Page 64 Using missiles is the most basic method of attack. A missile may still miss a locked on enemy if your timing is off. Align the lock-on cursor with an enemy to lock-on to them. Fire a missile while locked on and it will home in on the enemy. <After Burners>...
Page 65 Using CLIMAX Mode allows a larger number of enemies to be locked on to and taken out at once. During CLIMAX Mode the lock-on cursor expands, providing more opportunities to attack. You can now quickly lock onto multiple enemies. During CLIMAX Mode, the number of remaining missile shots is unlimited. In CLIMAX Mode, motion can begin by pushing the throttle lever all the way to CLIMAX position, the farthest point away from you.
Page 66 <Screen Explanation> - RIVAL: Position and direction of your rival. - RIVAL’S STATUS: An icon that displays your rival’s current status. Displayed on the right on the Player 01 screen and the left on the Player 02 screen. (Icons are: CLIMAX Mode, Down, Game Over) - DOWNED: Displayed when either player is shot down.
Page 67 CONTINUE Screen FIG. 8p CONTINUE Screen On the CONTINUE screen, select whether to continue the game or quit. The countdown appears in the middle of the screen. If the time runs out, NO will be automatically selected. To continue the game, perform the following before the countdown reaches 0. <Credit Remains>...
Page 68 Name Entry If stage 13A, 13B or stage 15 are cleared, and the score is in the top 20 then you can enter your name. FIG. 8q NAME ENTRY Screen A maximum of three characters can be entered. Name entry ends when END is selected or when time runs out. Move the control stick left/right to move the cursor.
Page 69 <Safety Sensor> If the sensor reacts during the game, the seat will stop moving immediately. The seat will not move so long as the sensor is reacting. State Message The sensor is reacting. Sensor is reacting. (On the PLAY Mode and PLAYER AIRCRAFT The seat will not move until the obstacles are SELECT screens) removed.
Page 70 Boeing. Produced under a license from Northrop Grumman Systems Corporation. F-14D Super Tomcat, F-5E Tiger II, A-10A Thunderbolt II, B-2A Spirit, and CVN-65 Enterprise are trademarks of Northrop Grumman Systems Corp. and are used under a license to Sega Corporation.
Page 71: Explanation Of Test And Data Display
EXPLANATION OF TEST AND DATA DISPLAY • Do not touch any parts that are not specified in these directions. Touching unspecified locations may lead to electric shock or cause short circuits. • In test mode, the seat moves in response to operations irrespective of the safety sensor or seatbelt. There are also cases in which the seat is released from its stationary central position (level condition). While operating in test mode, make sure that no one other than the operator is near the cabinet. Otherwise someone could contact or collide with the cabinet, or fall down.
Page 72 Perform tests and data checks periodically by manipulating the TEST Button and SERVICE Button in the cabinet. Follow the instructions in this chapter to conduct checks when the game machine is first installed, when money is being collected, or when the game machine does not operate properly. Shown below are the tests and screens to be used for different problems.
Page 73: Switch Unit And Coin Meter
-1 SWITCH UNIT AND COIN METER Switch Unit In test mode, the switch unit in the coin chute door is operated. Unlock and open the coin chute door. Inside is a switch unit. There is a monitor adjustment panel at the bottom. (See Chapter 10.) FIG.
Page 74 Coin Meter After using a special-purpose key to unlock the cashbox door, the coin meter can be found at the bottom of the cashbox. FIG. 9-1b Coin Meter...
Page 75: System Test Mode
- SYSTEM TEST MODE • The details of changes to test mode settings are saved when you exit from test mode by selecting EXIT from the system test mode menu. Be careful because if the power is turned off before that point, changes to the settings will be lost. • Use with the specified settings. If settings other than those specified are used, inappropriate operations or malfunction may occur. In the system test mode, the main activities include checking LINDBERGH information and actions and the setting of coin/credit. Also, a screen appears for checking screen adjustments. For details, see the LINDBERGH service manual, which is provided separately.
Page 76: Game Test Mode
- GAME TEST MODE To change settings in the game test mode, simply making changes on the setting screen will not be effective. Complete the test mode in normal fashion. Highlight GAME TEST Mode on the system test mode menu, and press the TEST Button to enter the game test mode. Once you enter the game test mode, the game test menu will be displayed. The items displayed on each test screen vary depending on the setting of CABINET TYPE on the game setting screen in game test mode.
Page 77 Press the SERVICE Button to highlight the desired menu item with the cursor. Press the TEST Button to perform the selected item. To learn how to proceed after executing the selected item, read the item’s explanation. You can also use the control stick and gun trigger to make selections in game test mode.
Page 78: Input Test
a. INPUT TEST • During the input test the seat will be unlocked and sensor checks will not be performed. Make sure that no one is standing too close, and take due care when performing the test. Because the seat inclines when it is pushed, there could be an accident. Someone could fall down, for instance, or get a finger or hand caught between something.
Page 79 The condition of each input device can be checked. Periodically check the condition of each input device on this screen. The number of items displayed varies depending on the setting of CABINET TYPE. <Operation> Manipulate the control stick or throttle lever and confirm that the input value on the right side of the item changes smoothly in response to manipulation.
Page 80 FIG. 9-3a03...
Page 81: Output Test
b. OUTPUT TEST • When output test is selected and confirmed from the game test mode menu screen, seat initialization takes place one time automatically. Be careful, as the seat moves left/right. Accidents could arise from contacting or colliding with the seat. Once initialization has completed, it will not take place again unless game test mode is first exited. • During output test, the seat becomes unlocked and checks by sensors do not take place. Make sure no one is nearby and execute the test while exercising due caution. During output test the seat inclines in response to manipulation even if the seatbelt is left unfastened and even if a safety sensor has been blocked. There could be accidents. Someone might fall down, for instance, or get a finger or hand caught in something.
Page 82 The condition of each output device can be checked. Periodically check the condition of each output device on this screen. Conditions are normal if each device operates and yields output as indicated below. The number of items displayed varies depending on the setting of CABINET TYPE. For safety, in performing tests in which the seat moves, manipulate the control stick and gun trigger without standing on the base.
Page 83 FIG. 9-3b03...
Page 84: Game Assignments
c. GAME ASSIGNMENTS When the store is crowded inside and motions might be dangerous to customers passing near the product, set the cabinet so it will not move, then operate the product. • Setting changes do not become effective until EXIT is selected on the setting screen. After a setting has been changed, be sure to always exit the setting screen.
Page 85 The various game settings are established. The number of menu items differs depending on the CABINET TYPE setting in game assignments. <Operation> Press the SERVICE Button, move the cursor to the item whose setting is to be changed and select the item. When the TEST Button is pressed, the preset value of the selected item changes.
Page 86: Network Setting
d. NETWORK SETTING • Network play cannot be implemented without proper setting for network play. Instead, an error message may be displayed. • Setting changes do not become effective until EXIT is selected on the setting screen. After a setting has been changed, be sure to always exit the setting screen. FIG. 9-3d01 NETWORK SETTING Screen (LINK NUM: 1) FIG.
Page 87 To setup network play with this product, connect two game machines with a network cable. Change to the settings for network play by proceeding as follows. The number of menu items differs depending on the LINK NUM setting. <Operation> Press the SERVICE button, move the cursor to LINK NUM and select it. When the TEST button is pressed, the value set for LINK NUM changes.
Page 88: Calibration
e. CALIBRATION • Change will not be effective simply by making a change on the calibration screen. When a setting has been changed, be sure to always exit the test mode. • Calibration is relevant to operability. Manipulate and adjust the input device with appropriate force. Do not make adjustments with excessive force. FIG. 9-3e01 CALIBRATION Screen Adjust the volume input value of the input device. When the volume has been replaced, check and adjust it on this screen.
Page 89 <Menu Explanation> CHECK: Proceed to the calibration check screen. SETTING: Proceed to the calibration screen. EXIT: Return to the game test menu screen. Calibration Check Screen FIG. 9-3e02 CALIBRATION Check Screen <Operation> Operate the input device whose input value is to be checked. When the TEST Button is pressed, the calibration screen reappears.
Page 90 Calibration Select Screen Shown below is the recommended range in the value for the center position of each volume. Attach volume so that its value is within this range. [Throttle lever: 80H ± 4H, Seat: 80H ± 4H] FIG. 9-3e03 CARIBRATION SELECT Screen <Operation> Press the SERVICE Button and move the cursor to the item you want to select. When the TEST Button is pressed, the calibration screen for the selected item appears.
Page 91 Control Stick Calibration Screen STEP 1 aligns the center position for the control stick. Press the TEST Bbutton after releasing your hand from the control stick. After determining the center position, proceed to STEP 2. FIG. 9-3e04 CONTROL STICK (STEP1) Screen STEP 2 aligns the MIN/MAX positions for the control stick.
Page 92 FIG. 9-3e06 CONTROL STICK (STEP2-2) Screen “ PRESS TEST BUTTON TO EXIT” is displayed. Press the TEST Button to set these MIN/MAX settings (left/right/forward/back) and return to the calibration select screen. Throttle Lever Calibration Screen STEP 1 aligns the center position for the throttle lever. Press the TEST Button after releasing your hand from the throttle lever.
Page 93 STEP 2 aligns the MIN/MAX positions for the throttle lever. Push the throttle lever as far as possible in both directions (forward/back). Make sure that you do not push the lever into CLIMAX Mode when inputting the MAX value. If you do so the game cannot be played properly.
Page 94 Seat Center Position Calibration Screen On this screen sensor checks will not be performed, and the seat will also be unlocked. Make sure that no one is standing too close and take due care when performing the test. Because the seat inclines when it is pushed, there could be an accident. Someone could fall down, for instance, or get a finger or hand caught between something. FIG. 9-3e10 SEAT CENTER POSITION Screen This screen allows you to adjust the seat’s center position. <Operation>...
Page 95: Bookkeeping
f. BOOKKEEPING Displays bookkeeping information across 4 screens. When the TEST Button is pressed, proceed to the next screen. When the TEST Button is pressed while the (4/4) screen is displayed, the game test mode menu screen reappears. FIG. 9-3f01 BOOKKEEPING Screen (1/4) <Menu Explanation>...
Page 96 FIG. 9-3f02 BOOKKEEPING Screen (2/4) <Menu Explanation> NUMBER OF GAMES: Total number of games played. TOTAL TIME: Total time that power has been supplied to the cabinet. (Time power is supplied, except during test mode.) PLAY TIME: Total play time. AVERAGE PLAY TIME: Average play time.
Page 97 FIG. 9-3f04 BOOKKEEPING Screen (4/4) <Menu Explanation> NUMBER OF GAMES: Total number of games. NUMBER OF GAME START: Total number of games started. NUMBER OF CONTINUE: Total number of continues. NUMBER OF GAMECLEAR: Total times the game has been cleared. NUMBER OF GAMEOVER: Total number of Game Overs.
Page 98: Backup Data Clear
g. BACKUP DATA CLEAR FIG. 9-3g01 BACKUP DATA CLEAR Screen <Menu Explanation> CLEAR ALL BACKUP DATA: Clear all data (both ranking and bookkeeping). CLEAR RANKING DATA(RANK01~20) ONLY: Clear only ranking data. CLEAR RANKING DATA(RANK11~20) ONLY: Clear only ranking data from (rank 11 to 20 only). CLEAR BOOKKEEP DATA ONLY: Clear only bookkeeping data.
Page 99 If you wish to clear data, press the SERVICE Button to highlight YES and then press the TEST Button. “COMPLETED” will be displayed once the data has been erased. When the TEST Button is pressed, the game test mode menu screen reappears. If you don’t wish to clear data, press the SERVICE Button to highlight NO and then press the TEST Button.
Page 100: Monitor
• When performing such work as installing and removing the monitor, inserting and disconnecting the external connectors to and from the monitor interior and the monitor itself, be sure to disconnect the power connector (plug) beforehand. Proceeding without doing so can cause electric shock or malfunctioning. • Use of the monitor by converting it without permission is not allowed. SEGA shall not be liable for any malfunctioning and accidents caused by such a conversion. • Primary side and Secondary side The monitor's circuit, which is divided into the Primary side and Secondary side, is electrically isolated. Do not touch the Primary side, or touch both the Primary...
Page 101 • High Voltage Some of the parts inside the monitor are subject to high voltage in excess of 20,000 volts and pose a serious threat. Therefore, do not touch the monitor interior. Should soldering & paper wastes, etc. be mixed in the monitor interior, turn the power off so as not to cause malfunctioning or a fire hazard. • Connecting the CRT and PCB When combining the CRT and PCB, use the specified part No. to maintain the factory settings. The anode of the CRT itself will charge as time elapses, generating high voltage that is very dangerous. The monitor should be used with the Chassis, CRT, and PCB assembled. When repair, etc. is required at the time...
Page 102: Cleaning The Crt Surfaces
Antistatic sheet is used in the product’s CRT to prevent electrification. To protect this sheet, observe the following precautions. If the sheet is damaged, the customer could be electrocuted. There are cases in which sheet edges peel off and turn white, but this poses no problems in usage. • Do not contact the antistatic sheet on the CRT surface, or rub it, with a hard implement (pointed bar or pen, etc.). • Do not affix stickers or anything e l s e t h a t m i g h t d a m a g e t h e antistatic sheet on the CRT surface, or cause the sheet to peel off.
Page 103: Adjustment Procedure
10- ADJUSTMENT PROCEDURE • Monitor adjustments have been made at the time of shipment. Therefore, do not make further adjustment without a justifiable reason. Adjusting the monitor which contains high tension parts is dangerous work. Also, an erroneous adjustment can cause deviated synchronization and image fault, resulting in malfunctioning. • Be sure to perform appropriate adjustment of the monitor (projector). For operation of this machine, do not leave monitor's flickering or deviation as is. Failure to observe this can cause to worsen the players' or the customers' physical conditions.
Page 104 This product’s monitor is 200-5955-04. For adjustment method, carefully read and carry out the following. With this product, the hue of each color cannot be adjusted. A: FUNC (SA04) B: UP (SA03) C: DOWN (SA01) D: DEGAUSS (SA05) There are four buttons to operate the adjustment. Pressing FUNC button displays the following menu screen.
Page 105 - Select the item (red display) and press the UP or the DOWN button once, the following display will appear. Contrast Adjusting Screen CONT Th e "n n n " i s a pre se n t v al ue o f th e adjustment value.
Page 106: Control Stick
CONTROL STICK • When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of fire. • Do not touch any parts that are not specified in these directions. Touching unspecified locations may lead to electric shock or cause short circuits. • This work should be performed by site maintenance personnel or other skilled professionals. Work performed by non-technical personnel can cause a severe accident such as an electric shock. • To prevent accidents while working or while operating the product after it has been installed, be sure not to conduct any procedures other than those given in this manual. There are cases in which procedures not covered in this manual require special tools and skills. If a procedure not given in this manual is...
Page 107: How To Remove Control Stick
• After the volume has been replaced, be sure to set the volume value on the test mode calibration screen and the input test screen and check variations in the volume value. • After adjusting or replacing a microswitch, always check ON/OFF of the switch on the input test screen of the test mode. • Handle parts inside the control stick very carefully. Be especially careful to avoid damage, deformation or loss of these parts. If any one of these parts is lost or defective, it can result in damages and/or faulty operations. If the operability of the control stick is unsatisfactory, or if settings on the test mode calibration screen are ineffective, the problem could be a defective mechanism, displacement of the position where volume or microswitch has been fastened, or malfunctioning of volume or microswitch.
Page 108 Open the controller lid at the bottom of the control stick. FIG. 11-1b Remove the 2 wire connectors on the control stick. FIG. 11-1c On the inside of the controller lid there is a cord clamp that holds wire to the surface on the right as you face the monitor.
Page 109 At the bottom of the control stick there is a board on the right side as you face the monitor. Of the connectors connected to this board, remove the connector on the monitor side. Be careful not to remove any connectors other than the one specified. Otherwise there could be damages, malfunctions, faulty connections, etc.
Page 110 Pull the control stick downward to remove it. Be careful not to damage wiring. FIG. 11-1i...
Page 111: Greasing
11- GREASING • Be sure to use the designated grease. Using undesignated grease can cause parts damage. • Do not apply grease to locations other than as specified. Doing so may create a risk of operational problems and deterioration of parts. • The designated periods for greasing serve only as a guide. Whenever there are squeaks or other anomalies, apply grease at designated locations. Once every 3 months, apply grease to the spring and sliding part of the mechanical component that turns the volume shaft. Use Greasemate (PART NO. 090-0066). FIG. 11-2...
Page 112: Volume Replacement
11- VOLUME REPLACEMENT If control stick operability is unsatisfactory and settings on the test mode calibration screen are ineffective, the problem could be a malfunction of the control stick volume. Remove the control stick and replace the volume. Please note, however, that the control stick has two volumes. Make sure you are replacing the correct volume. Have available a volume for replacement and three thermal contraction tubes (PART NO.
Page 113 Remove the volume together with volume bracket from the control stick. FIG. 11-3b Take off the hexagon nut that fastens the volume to the volume bracket, then remove the volume from the bracket. FIG. 11-3c Wire connected to the volume can be used as is. Use nippers or cutters to remove old thermal contraction tube from wire connection sites.
Page 114 If the length of wire exposed at the wire tip does not reach 5 mm, use wire stripper or cutter to remove wire cover. FIG. 11-3e Pass one wire through each thermal contraction tube. FIG. 11-3f Solder wire to the pin of the new volume. Refer to wiring diagram and make sure that you are using soldering wire.
Page 115 Heat with industrial dryer and affix thermal contraction tube so that it covers soldered area. FIG. 11-3h Attach the volume to the volume bracket, then attach this assembly to the control stick. Align the D-cut surface of the volume shaft with the D-cut surface of the hole on the side of the control stick, then insert the shaft.
Page 116: Microswitch Replacement
11- MICROSWITCH REPLACEMENT If operability of the gun trigger is unsatisfactory, the problem could be a malfunction of the microswitch inside the control stick grip. Remove the control stick and replace the microswitch. Use the following tools, solder and screw lock agent (PART NO. 090-0012). - 2.5 mm Allen wrench or screwdriver - 8 mm spanner, Allen screwdriver or socket wrench - Philips screwdriver (for M4 screw)
Page 117 The grip L microswitch is inserted. Pull out the microswitch slowly so as not to damage wire. FIG. 11-4d Use a soldering iron to remove wire to be connected by solder to microswitch pin. Solder wire to the pin of the new microswitch. Insert microswitch into grip L, then attach grip L.
Page 118: Guide Plate Replacement
11- GUIDE PLATE REPLACEMENT Among the potential causes of abnormal control stick operability, apart from volume malfunctions, are wear and/or damage to guide plates. Use the following tools to replace a guide plate. - 2.5 mm Allen wrench or screwdriver - 4 mm Allen wrench or screwdriver Cut off the power and open the controller lid at the bottom of the control stick.
Page 119: Throttle Lever
THROTTLE LEVER • When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of fire. • Do not touch any parts that are not specified in these directions. Touching unspecified locations may lead to electric shock or cause short circuits. • This work should be performed by site maintenance personnel or other skilled professionals. Work performed by non-technical personnel can cause a severe accident such as an electric shock. • Exercise due caution in performing soldering procedures. If soldering iron is handled carelessly, there could be fires or burns.
Page 120: Greasing
1-1 GREASING • Be sure to use the designated grease. Using undesignated grease can cause parts damage. • Do not apply grease to locations other than as specified. Doing so may create a risk of operational problems and deterioration of parts. • The designated periods for greasing serve only as a guide. Whenever there are squeaks or other anomalies, apply grease at designated locations. Once every 3 months apply grease to the spring and gear mesh that turn the volume shaft. Use Greasemate (PART NO. 090-0066). Cut off the power supply. Remove the 4 truss screws that hold the throttle cover lower. Flat washers are used with the truss screws. FIG.
Page 121 Apply grease only at designated locations. FIG. 12-1d When attaching throttle cover lower, make sure that wires do not get caught anywhere.
Page 122: Volume Adjustment Or Replacement
1- VOLUME ADJUSTMENT OR REPLACEMENT When the volume that detects throttle lever operation is unsatisfactory, either adjust the gear mesh or replace the volume by proceeding as follows. With this product, when the lever has been operated fully to front or rear, if the volume rotary shaft turns within its movable range, there is no danger that the volume will be damaged.
Page 123 Adjust the gear mesh so that the volume shaft turns smoothly when the lever is manipulated and so that the incline of the volume shaft (D cut surface direction) when hand is removed from the lever is as shown in the illustration.
Page 124 Replacement Method Make available the volume for replacement and 3 thermal contraction tubes (PART NO. 310-5029-D20). Cut off the power supply. Take out the 4 truss screws and remove the throttle cover lower. (See 12-1.) Unfasten the 2 cord clamps that hold down wire connected to the volume. FIG.
Page 125 Remove the 2 screws that fasten the VR bracket. Flat and spring washers are used with these screws. FIG. 12-2e Remove the volume together with VR bracket. Be careful not to damage the wire connected to the volume. FIG. 12-2f Loosen the 2 hexagon socket screws that fasten the gear.
Page 126 Remove the nuts that fasten the VR bracket, then remove volume from VR bracket and replace. The wire connected to the volume is used as is. Take away the thermal contraction tube with nippers or cutter, melt the soldered areas with a soldering iron and remove wire from the volume. Cover the soldered areas with thermal contraction tube.
Page 127: Roll Volume
ROLL VOLUME • When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of fire. • Do not touch any parts that are not specified in these directions. Touching unspecified locations may lead to electric shock or cause short circuits. • This work should be performed by site maintenance personnel or other skilled professionals. Work performed by non-technical personnel can cause a severe accident such as an electric shock. • To prevent accidents while working or while operating the product after it has been installed, be sure not to conduct any procedures other than those given in this manual. There are cases in which procedures not covered in this manual require special tools and skills. If a procedure not given in this manual is...
Page 128: Greasing
After the volume has been replaced, be sure to set the volume value on the test mode calibration screen and the input test screen and check variations in the volume value. The volume that detects seat inclination is the roll volume. It is inside the front pillar cover. 1-1 GREASING • Be sure to use the designated grease. Using undesignated grease can cause parts damage. • Do not apply grease to locations other than as specified. Doing so may create a risk of operational problems and deterioration of parts. • The designated periods for greasing serve only as a guide. Whenever there are squeaks or other anomalies, apply grease at designated locations.
Page 129 Remove the 2 hexagon socket screws from the front surface. A spring washer and special washer are used with the hexagon socket screws. FIG. 13-1b Remove the front pillar cover. FIG. 13-1c Apply grease only to the gear mesh component. FIG.
Page 130: Roll Volume Adjustment Or Replacement
1- ROLL VOLUME ADJUSTMENT OR REPLACEMENT When seat movement is unsatisfactory and settings on the test mode calibration screen are ineffective, the problem could be faulty volume gear mesh, volume malfunction or an anomaly in a moving mechanical component. With this product, when the seat has been tilted fully to the right or left, if the volume rotary shaft turns within its movable range, there is no danger that the volume will be damaged.
Page 131 Rotate the gear so that the D cut surface of the volume shaft is level, facing directly upward. Align so that the gear does not rotate, then tighten the 2 screws that hold down the roll volume bracket. FIG. 13-2b Turn on the power.
Page 132 Replacement Method Make available the volume for replacement and 3 thermal contraction tubes (PART NO. 310-5029-F20). Cut off the power supply. Remove the front pillar cover. Remove 1 truss screw and 2 hexagon socket screws. (See 13-1.) Unfasten the cord clamp that holds down volume wire. FIG.
Page 133 Remove the 2 screws that hold down the roll volume bracket. Flat and spring washers are attached with these screws. FIG. 13-2e Remove the roll volume bracket together with volume. Be careful not to damage wire connected to the volume. FIG.
Page 134 Remove the nut that holds down the roll volume bracket, then remove volume from roll volume bracket and replace it. The wire connected to the volume is used as is. Cut away the thermal contraction tube with nippers or cutter, melt the soldered areas with a soldering iron and remove wire from the volume.
Page 135: Coin Selector
COIN SELECTOR Handling the Coin Jam If the coin is not rejected when the REJECT button is pressed, open the coin chute door and open the selector gate. After removing the jammed coin, put a normal coin in and check to see that the selector correctly functions. Cleaning the Coin Selector • Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry.
Page 136 Remove and clean smears by using a soft cloth dipped in water or diluted chemical detergent and then squeezed dry. Remove the CRADLE. When removing the retaining ring (E ring), be very careful so as not to bend the rotary shaft. FIG.
Page 137: Replacing The Fluorescent Lamps
REPLACING THE FLUORESCENT LAMPS • When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit. • You may get burned by a hot fluorescent lamp or other lamps. Pay full attention to the lamps when performing the work. • There is the danger of short circuits or smoke generation due to deterioration of insulation in lighting fixtures resulting from age deterioration. Check for anomalies such as the following: Does it smell like something is burning? Is there socket discoloration? Are any lamps being replaced frequently? Do lamps not go on properly? • Before turning on the power after a fluorescent lamp has been replaced, inspect carefully to see if anyone is near the product or if tools or other items have been left on the product. When the power is turned on, initialization takes place automatically. If anyone is near the product, they could collide with the...
Page 138 This product has 1 fluorescent lamp in the billboard and 1 fluorescent lamp each at the top and bottom of the seat backrest rear surface. Billboard Cut off the power supply. Remove 4 truss screws from atop the billboard. FIG. 15a Remove the billboard lid and replace the fluorescent lamp.
Page 139 Underside of Seat Backrest Rear Surface Cut off the power supply. Remove 7 hexagon socket screws. Use a 2.5 mm Allen wrench or screwdriver. Spring washers and special washers are used with the hexagon socket screws. FIG. 15c FIG. 15d Remove the rear pillar plate.
Page 140 To remove the rear pillar cover, remove the 2 screws on the bottom and the 8 hexagon socket screws. FIG. 15f FIG. 15g Remove the 8 screws (2 on top, 6 on bottom) and the FL 25W COVER, then replace the fluorescent lamp. FIG.
Page 141 Upper Side of Seat Backrest Rear Surface Cut off the power supply. To remove the headrest cover, remove the truss screws to the left and right and the 4 hexagon socket screws. FIG. 15j Remove the 4 screws and the FL 6W COVER, then replace the fluorescent lamp. FIG.
Page 142: Periodic Inspection
PERIODIC INSPECTION • Once a year, check to see if power cords are damaged, the plug is securely inserted, dust is accumulated between the socket outlet and the power plug, etc. Using the product with accumulated dust in the interior may cause fire or electric shock. • Never use a water jet, etc. to clean the inside and outside of the cabinet. If wetness occurs for any reason, do not use the product until it has completely dried. • Once a year, request the office shown on this manual or the dealer from whom the product was originally purchased to perform the internal cleaning. Using the product with accumulated dust in the interior may cause fire or other accidents. Note that you are liable for the cost of cleaning the interior parts. • Once a year, request the office shown in this manual or the dealer from whom the product was originally purchased to perform routine maintenance on moving mechanisms. Failure to perform maintenance can lead to accidents.
Page 143 TABLE 16 PERIODIC INSPECTION TABLE ITEMS DESCRIPTION PERIOD REFERENCE CABINET Confirm that adjusters contact Daily floor MONITOR Screen cleaning Weekly 10-2 Check screen adjustment Monthly or 6 7 , 10-3 when moving CONTROL STICK Inspection of volume, switch 1 month 9-3a Greasing 3 months...
Page 144: Troubleshooting
TROUBLESHOOTING • If an error message is displayed, have the problem looked at by a store maintenance person or a technician. Unless the problem is addressed by someone with specialized knowledge or skills, there could be electrical shock, short circuits or fire. If there are no store maintenance people or technicians, or moving mechanisms are involved, cut off the power immediately and contact the office shown in this manual or the dealer from whom the product was originally purchased.
Page 145: Error Messages
1-1 ERROR MESSAGES • Apart from the error messages given below, there are errors for the LINDBERGH. Consult the LINDBERGH service manual. • If there is an error message other than the ones below or those in the LINDBERGH service manual, stop using the product and have the LINDBERGH sent for servicing. Because the seat moves, and for other reasons, this product has a unique set of error messages. These error messages appear in the middle of the screen as shown below.
Page 146 [DISPLAY] Error ABX01 MOTOR DRIVE COMMUNICATION ERROR [CAUSE] A motor drive communication error. [COUNTERMEASURES] Failure to communicate with the control board for seat movement. Check the cable connecting them. [DISPLAY] Error ABX02 MOTOR DRIVE OVERHEATING/OVERLOAD ERROR [CAUSE] A motor drive overheating/overload error. [COUNTERMEASURES] The seat movement motor thermal element has been activated.
Page 147: Troubleshooting Table
1- TROUBLESHOOTING TABLE If a problem has occurred, first inspect the connection of the wiring connector. TABLE 17-2 PROBLEMS CAUSE COUNTERMEASURES When the main SW is The power is not ON. Firmly insert the plug into the outlet. turned ON, the machine is not activated.
Page 148 PROBLEMS CAUSE COUNTERMEASURES Irregular/uneven colors Magnetization of the CRT. Press the DEGAUSS button on the adjustment on the monitor screen. board. (See 10-3.) Colors on the monitor Faulty connection for the Check the visual signal connector connection screen are strange. visual signal connector.
Page 149 PROBLEMS CAUSE COUNTERMEASURES Seat does not move. Initialization procedures are Confirm that initialization completes normally. inadequate. (See chapter 6 6 .) Settings are incorrect. Check settings of CABINET TYPE and CABINET MOVEMENT on game setting screen. (See 9-3c.) Faulty connection of Check connections of connectors between game connectors.
Page 150: Replacing Fuses
1- REPLACING FUSES • Never replace a fuse with anything other than designated fuse. Otherwise there could be accidents. In case fuse replacements other than those stated in this manual are necessary, contact where you purchased the product from for inquiries regarding this matter. • In order to prevent an electric shock, be sure to turn power off and unplug from the socket outlet before performing work by touching the internal parts of the product. • Be careful so as not to damage wiring. Damaged wiring can cause electric shock and short circuit accidents. • Be sure to use fuses meeting specified rating. Using fuses exceeding the specified rating can cause fire and electric shock accidents.
Page 151 Remove the front door. FIG. 17-3b Replace fuse inside base. FIG. 17-3c...
Page 152: Game Board
GAME BOARD • When working with the product, be sure to turn the power off. Working with the power on may cause an electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a fire risk. • Do not expose the game board, etc. without a good reason. Failure to observe this can cause electric shock hazard or malfunctioning. • Do not use this product with connectors other than those that were connected and used with the game board at the time of shipping. Do not carelessly connect wires to connectors that were not used at the time of shipping, as this may cause overheating, smoke or fire damage. • When returning the game board after making repairs or replacements, make sure that there are no errors in the connection of connectors. Erroneous connections can lead to electrical shock, short circuits or fires.
Page 153: How To Remove Game Board
• When a game board is to be replaced, put the old game board with anomaly into a special box for replacing the game board and send it. If a special box is not available or if it has been damaged, arrange to obtain a box with the following part number/name. 601-11691 / CARTON BOX LBG • For replacement or repair, pack the game board and send it without disassembling it. Order for servicing might not be accepted if any part of the game board has been removed. If any part is removed, a service fee will be charged even if the warranty period has not yet expired. • Do not remove the key chip from the game board before sending the board for servicing.
Page 154 Unlock and remove rear door R. FIG. 18-1b Remove 2 connectors at right and left of the wooden base on which the LINDBERGH is mounted. FIG. 18-1c Remove the connector of the LAN, JVS, D-SUB cable connected to the LINDBERGH. When sending the LINDBERGH for replacement or repair, all the connectors connected to the LINDBERGH here can be removed.
Page 155 Remove 2 butterfly screws that hold down the wooden base. Flat washer and spring washer are used with the butterfly screws. FIG. 18-1e Remove the wooden base together with the LINDBERGH. Be careful not to pull on wires or cables, or let them get caught so that they become damaged.
Page 156 Remove 4 screws that hold down the LINDBERGH. Flat washers and spring washers are used with these screws. FIG. 18-1h...
Page 157: Composition Of The Game Board
1- COMPOSITION OF THE GAME BOARD • With the key chip inserted into it, this board serves as a special-purpose game board for the product. • Use with the dip switches (DIP SW) on the board at the prescribed settings. If settings do not match the product, an error message will be displayed. In some cases, the game cannot be started. ASSY CASE LBG L 1GB ABX USA (844-0007D-01) FIG. 18-2a DIP SW SETTING Use this product with the DIP SW settings shown in the figure below. FIG.
Page 158: Design Related Parts
DESIGN RELATED PARTS For the warning display stickers, refer to Section 1.
Page 159: Network Play
NETWORK PLAY Network play can be enjoyed with this product by having two units connected by LAN cable. 0-1 PRECAUTIONS REGARDING NETWORK PLAY SETUP • Before starting to work, ensure that the power switch is OFF. Failure to observe this can cause electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause electric shock or short circuit or present a fire risk. • Do not touch undesignated places. Touching places not designated can cause electric shock or short circuit. • This work should be performed by the site maintenance individual or other skilled professional. Performing work with non-technical personnel can cause electric shock.
Page 160 Game Unit Installation Because of the game screen composition, it is recommended that installed game machines used for network play be aligned left and right. (mm) FIG. 20-1 Installation for network play...
Page 161: Network Cable Connections
0- NETWORK CABLE CONNECTIONS To setup network play, connect the two game machines for network play with a network (LAN) cable. Do not connect a network cable to any game machine not being used for network play. Have available the accessory network cable, Philips screwdriver for M4 screws, and a 24 mm spanner. Cut off the power and pull the power plug from the outlet.
Page 162 Connect the connector at one end of the network cable to the port. Connect the connector at the opposite end to the port of the other game unit. FIG. 20-2c Move the two game machines joined by network cable and install them aligned. For ventilation, establish an interval of at least 150 mm between one machine and any other machine or the wall.
Page 163: Network Play Setting
0- NETWORK PLAY SETTING When the power has been engaged or the test mode has been terminated, initialization takes place automatically. If anyone is near the product, they could come in contact or collide with it. Check carefully to be sure that no one is near the product and that no tools or items have been left on the product, then engage the power or terminate test mode. Upon completion of initialization, call up the network check screen and check connections and settings for network play. If the network check screen appears continuously on one machine, an error message is displayed. The power must be re-engaged and the test mode must be established and terminated once. Set the two game machines for network play. If the setting is incorrect, network play cannot be implemented. Power up the two game machines for network play.
Page 164 On the network play setting screen, set LINK NUM. Press the SERVICE Button, move the cursor onto LINK NUM and select it. When the TEST Button is pressed, the LINK NUM preset value changes. Set “2” in each of the two game machines.
Page 165: Precautions In Network Play
0- PRECAUTIONS IN NETWORK PLAY • If communication is interrupted during network play for any reason, network play is disabled and game play continues on each machine individually. If communication is interrupted in the Attract Mode, the network check screen appears.
Page 166: Optional Items
Performing the work without turning the power off can cause an electric shock or short circuit. • Be careful not to damage the wires. Damaged wires may cause an electric shock, short circuit or present a risk of fire. The following optional items are available for AFTER BURNER CLIMAX. - Dollar Bill Validator: 1 set - Security Bar Lower: 1 set...
Page 167 Undo the cord clamp. FIG. 21-1b Remove the 4 carriage bolts and 4 nuts, then remove the Blind Plate. The carriage bolts and nuts will be used later. FIG. 21-1c FIG. 21-1d Undo the cord clamp for the cable connecting to the Coin Selector. FIG.
Page 168 Temporarily remove the Coin Selector. FIG. 21-1f Attach the Dollar Bill Validator using the 4 carriage bolts and 4 nuts removed in step 4. FIG. 21-1g FIG. 21-1h Return the Coin Selector to its original position. FIG. 21-1i...
Page 169 Connect the connector for the Dollar Bill Validator. FIG. 21-1j Affix the supplied cord clamp as shown in the figure, and fasten the connector cable. Be careful that the cable does not get caught when opening and closing the coin chute door.
Page 170: Security Bar Lower
1- SECURITY BAR LOWER Security Bar Lower Installation Cut off the power supply. Attach the Security Bar Lower Sponge to Security Bar Lower R as shown in the illustration. FIG. 21-2a FIG. 21-2b...
Page 171 Use the cash box door key to unlock and open the cash box door. FIG. 21-2c Remove the nuts to the left and right (2 on each side) that hold down the Stud Plate, then remove the Stud Plate. The nuts will be used later. FIG.
Page 172 From the Security Bar Lower interior, firmly tighten the nuts removed in step 4. Attach the other side in the same manner. FIG. 21-2g FIG. 21-2h Lock the cash box door and the Security Bar Lower. FIG. 21-2i FIG. 21-2j...
Page 173: Security Bar Upper
1- SECURITY BAR UPPER Security Bar Upper Installation Cut off the power supply. Attach the Security Bar Stopper to the Security Bar Upper L/R using 2 screws each (total of 4). SECURITY BAR STOPPER SCREW (4), black M4×8, w/spring washer SECURITY BAR UPPER SPONGE SECURITY BAR UPPER R SECURITY BAR STOPPER...
Page 174 Use the coin chute door key to unlock and open the coin chute door. FIG21-3d Remove the nuts to the left and right (2 on each side) that hold down the Stud Plate, then remove the Stud Plate. The nuts will be used later.
Page 175 From the Security Bar Upper interior, firmly tighten the nuts removed in step 5. Attach the other side in the same manner. FIG21-3g Lock the coin chute door and the Security Bar Upper. FIG21-3h...
Page 176: Parts List
PARTS LIST...
Page 177 1 TOP ASSY ABX UL (D-1/)
Page 178 1 TOP ASSY ABX UL (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1000 ASSY ROLLING BASE ABX-1100 ASSY MONITOR BOX ABX-1200 ASSY COINCHUTE TOWER ABX-1300 ASSY MONITOR MASK ABX-1400 ASSY CONTROLLER BASE ABX-1500 ASSY BILLBOARD ABX-1600 ASSY SEAT BASE ABX-1650 THROTTLE UNIT ABX-1700 ASSY SEAT UPPER...
Page 179 1 TOP ASSY ABX UL (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-0044 NON SLIP MAT R 421-8479-01 STICKER INSTR SUNLIGHT ENG 421-11416 STICKER CAUTION FORK 421-7501-05 STICKER FL 6W 421-7501-51 STICKER FL25W 440-WS0141-EG STICKER W HIGH TEMP S ENG 440-WS0142-EG STICKER W POWER OFF S ENG 440-WS0166-EG...
Page 180 1 TOP ASSY ABX UL (D-/) ITEM NO. PART NO. DESCRIPTION NOTE 600-7269-0300 ASSY LAN CABLE 0300CM 420-6921-01 SERVICE MANUAL LBG ENG 220-5753 VOL CONT B-5K OHM (TOCOS) 509-5975 SW MICRO TYPE SS-5GL (OMRON) 220-5737 VOL CONT B-5K(RA25Y20F COSMOS) ABX-0048 FL 6W COVER BRKT ABX-0049 FL 6W COVER...
Page 181 ASSY ROLLING BASE (ABX-1000) (D-1/)
Page 182 REAR SENSOR HOLDER R ABX-3553X REAR PIPE LID R ABX-1034 BASE RUBBER BRKT R 100-5240-01 BEARING 30 NTN UCPE206 W/HOLE 280-6676 CORD CLAMP TL-25A TKK 280-5275-SR10 CORD CLAMP SR10 310-5027-1303 INSL SLIT TUBE ID13 370-5298-01 BEAM SENSOR L-9382-12(SEGA) 370-5298-02 BEAM SENSOR R-9382D-12(SEGA)
Page 183 ASSY ROLLING BASE (ABX-1000) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE 000-T00408-0B M SCR TH BLK M4x8 020-000616-0Z HEX SKT H CAP SCR BLK 0Z M6x16 060-S00600-0B SPR WSHR BLK M6 060-F00600-0B FLT WSHR BLK M6 030-000820-S HEX BLT W/S M8x20 060-F00800-0B FLT WSHR BLK M8 000-P00408-W...
Page 184 ASSY PILLAR BASE (ABX-000) (D-1/)
Page 185 ASSY PILLAR BASE (ABX-000) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3001X ASSY BASE ABX-3003X FRONT PILLAR ABX-3004 FRONT PILLAR RUBBER A ABX-3005X REAR PILLAR ABX-3006 REAR PILLAR RUBBER A ABX-3007 BASE SASH ABX-3008 EDY CABLE LID TX-2017 COMP SPRING ABX-3009X SPRING SUPPORT 610-0757...
Page 186 ASSY BASE (ABX-001X) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3002X BASE 601-11312 CASTER 50(TAKIGEN K-300HJ-50) 601-5882 LEG ADJUSTER (TAKIGEN C-280-2) 030-00620-S HEX BLT W/S M6x20 068-652016 FLT WSHR 6.5-20 x1.6 050-H01600-0B HEX NUT BLK M16...
Page 187 FAN UNIT (10-0) Connector Position ITEM NO. PART NO. DESCRIPTION NOTE 105-5561 FAN BRKT 260-0011-03 AXIAL FLOW FAN AC100V 50-60HZ 601-8543 FAN GUARD 000-P00312-W M SCR PH W/FS M3x12...
Page 188 ASSY WIRE PILLAR BASE UL (ABX-001-01) This is comprised of the following wire harnesses. ASSY drawing is not available. ITEM NO. PART NO. DESCRIPTION NOTE 601-0460 PLASTIC TIE BELT 100 MM ABX-60023 WH BASE01 ABX-60025 WH BASE02 ABX-60026 WH BASE03 ABX-60027 WH BASE04 ABX-60028...
Page 189 AC UNIT (ABX-100) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3101X AC BRKT ABX-3102X LAN JOINT HOLDER ABX-3103 LAN LID 421-8202 STICKER EARTH MARK 421-7468-01 STICKER C.P W/PIC 214-0202 AC INLET PANEL TYPE 270-5081 NOISE FILTER 20A 509-6102-V-B SW ROCKER J8 V-B AJ8202BF 512-5046-15000 C.P 15000MA CE UL 450-5135...
Page 190 MOTOR UNIT (ABX-00) (D-1/)
Page 191 MOTOR UNIT (ABX-00) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3201X MOTOR UNIT BASE 253-5592 MOTOR INSULATOR A 253-5593 MOTOR INSULATOR B ABX-3202X MOTOR BRKT ABX-3208 REDUCTION BRKT B ABX-3204X WHEEL BRKT ABX-3205X SPRING BRKT ABX-3206 WATER COVER ABX-3207 DRIVE WHEEL ABX SPG-2453 KEY 4x4x40...
Page 192 ASSY STOPPER (ABX-00) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3401 STOPPER BASE ABX-3402 STOPPER RUBBER ABX-3403 STOPPER URETHANE ABX-3404 RUBBER BRKT 000-P00408-W M SCR PH W/FS M4x8...
Page 193 10 BEAM SENSOR UNIT XMTR (ABX-00) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3601X BEAM SENSOR BRKT 370-5298-01 BEAM SENSOR L-9382-12(SEGA) 000-P00316-W M SCR PH W/FS M3x16 050-H00300 HEX NUT M3...
Page 194 11 BEAM SENSOR UNIT RCVR (ABX-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3601X BEAM SENSOR BRKT 370-5298-02 BEAM SENSOR R-9382D-12(SEGA) 000-P00316-W M SCR PH W/FS M3x16 050-H00300 HEX NUT M3...
Page 195 1 ASSY XFMR (ABX-000) ITEM NO. PART NO. DESCRIPTION NOTE ABX-4001-01 WOODEN BASE XFMR UL 421-12200-6300 STICKER FUSE SG5013 T 6.3A 560-5557-V XFMR 100-120V 100V120V 24V WB 838-14551-02 DISTRIBUTION BD W/FUSEX2 280-6676 CORD CLAMP TL-25A TKK 280-0419 HARNESS LUG 514-5138-6300 FUSE SG5013 5x20 6300MA 250V 000-P00516-W M SCR PH W/FS M5x16...
Page 196 1 ASSY ELEC (ABX-100) NOTE: Make sure that there is no parts, wiring, etc. in the slash mark portions. ITEM NO. PART NO. DESCRIPTION NOTE ABX-4101 WOODEN BASE ELEC 839-1148R 4A DC SSR BD NH4P 400-5421-15024 SW REGU LCA150S-24 280-5277 CORD CLAMP 18 280-0419 HARNESS LUG 280-6681 L-LOCK LT-320PCG 838-14592 SERVO MOTOR DRIVE BD SER 838-14515-A0191 SOUND AMP ANALOG IN 011-P00325...
Page 197 1 ASSY MAIN BD (ABX-00) NOTE: Make sure that there is no parts, wiring, etc. in the slash mark portions. ITEM NO. PART NO. DESCRIPTION NOTE ABX-4201 WOODEN BASE MAIN BD 844-0001D-91-11 ASSY CASE LBG L 1GB 7800 USA HDF-4202 BRKT PWR SPLY 839-1256R RS232 TO 422 & 485 BD 400-5457-91 SW REGU ATX/JVS 400-5421-03012 SW REGU LCA30S-12 280-6676...
Page 198 STICKER FLOOR L UL ABX-3805-01 STICKER FLOOR R UL ABX-3806 FLOOR SENSOR BRKT ABX-3807 FLOOR SENSOR COVER 370-5298-01 BEAM SENSOR L-9382-12 (SEGA) 370-5298-02 BEAM SENSOR R-9382D-12 (SEGA) 280-5275-SR10 CORD CLAMP SR10 050-F00500 FLG NUT M5 068-552016 FLT WSHR 5.5-20 x1.6...
Page 199 1 ASSY FRONT DOOR (ABX-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3821 FRONT DOOR ABX-3822 WOODEN BASE FRONT DOOR ABX-3823X STICKER FRONT DOOR SIDE ABX-3824 STICKER FRONT DOOR UPPER 050-F00500 FLG NUT M5 068-552016 FLT WSHR 5.5-20 x1.6...
Page 200 1 ASSY REAR DOOR L (ABX-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3841X REAR DOOR DP-1167 TNG LKG ABX-3842X STICKER REAR DOOR L 220-5793-1-A001 CLY LOCK MASTER W/O KEY A001...
Page 201 1 ASSY REAR DOOR R (ABX-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3841X REAR DOOR DP-1167 TNG LKG ABX-3861X STICKER REAR DOOR R 220-5793-1-A001 CLY LOCK MASTER W/O KEY A001...
Page 202 1 ASSY WHEEL COVER L (ABX-100) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1007-02 WHEEL COVER L UL ABX-1016-01 STICKER BASE FRONT UL ABX-3650 BEAM SENSOR UNIT RCVR ABX-1006 SENSOR COVER 280-5275-SR10 CORD CLAMP SR10 000-P00408-W M SCR PH W/FS M4x8 000-T00408-0B M SCR TH BLK M4x8...
Page 203 0 ASSY WHEEL COVER R (ABX-100) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1008-01 WHEEL COVER R UL ABX-1016-01 STICKER BASE FRONT UL ABX-3600 BEAM SENSOR UNIT RCVR ABX-1006 SENSOR COVER 280-5275-SR10 CORD CLAMP SR10 000-P00408-W M SCR PH W/FS M4x8 000-T00408-0B M SCR TH BLK M4x8...
Page 204 1 ASSY WIRE ROLLING BASE UL (ABX-00-01) This is comprised of the following wire harnesses. ASSY drawing is not available. ITEM NO. PART NO. DESCRIPTION NOTE 601-0460 PLASTIC TIE BELT 100 MM ABX-60081 WH CRADLE01 UL ABX-60040 WH CRADLE02 ABX-60041 WH CRADLE03 ABX-60042X WH CRADLE04...
Page 205 ASSY MONITOR BOX (ABX-1100) (D-1/)
Page 206 ASSY MONITOR BOX (ABX-1100) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1160 ASSY SPEAKER L ABX-1180 ASSY SPEAKER R ABX-1101X MONITOR BASE 280-6696 SPCL WSHR 5.5-20x6.3 AL YEL 280-5112 BUSH FOR TV 280-5113 COLLAR FOR TV 280-5114 SPACER 6.4-25x2 ABX-1103 HAND GRIP L ABX-1104...
Page 207 ASSY SPEAKER L (ABX-110) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1161X SPEAKER BRKT 130-5156-02 SPEAKER BOX 8OHM 20W VA1 YL 000-P00512-WB M SCR PH W/FS BLK M5x12...
Page 208 ASSY SPEAKER R (ABX-110) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1161X SPEAKER BRKT 130-5156-02 SPEAKER BOX 8OHM 20W VA1 YL 000-P00512-WB M SCR PH W/FS BLK M5x12...
Page 209 ASSY COINCHUTE TOWER (ABX-100) (D-1/)
Page 210 ASSY COINCHUTE TOWER (ABX-100) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1201-01 COINCHUTE TOWER UL ABX-1260 ASSY CASH BOX DOOR ABX-1280 SW UNIT ABX-1204-01 CHUTE PLATE UL 421-9168-01 STICKER COIN METER 421-7501-02 STICKER 6.3V 0.15A 220-5818 CC 1DR W/O DBA HAPP 40-0870-00 220-5798-01 MAG CNTR 4P MZ674-DC5V-D41 JC 310-5029-F20...
Page 211 ASSY CASH BOX DOOR (ABX-10) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1261 CASH BOX DOOR HOT-1203X CENTER TNG ABX-1262 SIDE TNG 220-5794 CLY LOCK W/KEYS 060-F00400-0B FLT WSHR BLK M4 065-E00300 E RING 3MM...
Page 212 SW UNIT (ABX-10) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1281 SW BRKT 421-11669 STICKER SW UNIT FZR STD 509-5028 SW PB 1M (MIYAMA DS-412R) 220-5810 VOL CONT C5KOHM(RV24YN15SC502) 601-0042 KNOB 22 MM 310-5029-D20 SUMITUBE F D 20MM 601-0460 PLASTIC TIE BELT 100 MM ABX-60060 WH SW UNIT01 ABX-60061...
Page 213 ASSY MONITOR MASK (ABX-100) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1301 MONITOR MASK ABX-1302-01 STICKER INSTR UPPER ENG ABX-1303-01 STICKER INSTR LOWER L ENG ABX-1304-01 STICKER INSTR LOWER R ENG ABX-1305 BEZEL SPONGE LONG ABX-1306 BEZEL SPONGE SHORT...
Page 214 ASSY CONTROLLER BASE (ABX-100) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1450 ASSY SW PLATE ABX-1401X CONTROLLER BASE 839-1187R AMP BD FOR ANALOG JOYSTICK ABX-1402 CONTROLLER LID 280-6695 SPCL WSHR 4.5-16x5 AL BLK ABX-1403 CONTROLLER PLATE 610-0756 ASSY ANALOG JOY ABX 280-5008 CORD CLAMP 15 008-T00410-0C...
Page 215 0 ASSY SW PLATE (ABX-10) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1451-01 SW PLATE EXP 509-6084-YY SW PB OBSA-30UM-Y-1F LED-Y-12V 509-6084-RLN SW PB OBSA-30UM-R-1F LN...
Page 217 ASSY BILLBOARD (ABX-100) (D-1/)
Page 218 ASSY BILLBOARD (ABX-100) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1501X LED BOX ABX-1502 LED HOLDER 839-1308 RGB LED 6 BAR ABX BD ABX-1503 LED PLATE ABX-1504 LED PLATE HOLDER L ABX-1505X BILLBOARD BOX ABX-1514 CUSHION SPONGE SASH ABX-1507 BILLBOARD ACRYL PLATE CTF-1002 WASHER CTF...
Page 219 ASSY SEAT BASE (ABX-100) (D-1/)
Page 220 ASSY SEAT BASE (ABX-100) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1601X SEAT BASE ABX-1602 LOWER SEAT ABX-1603 SEAT BELT CATCH ABX-1604 SEAT BELT CATCH COVER ABX-1605X SEAT BELT BASE ABX-1606 SEAT CLEARANCE BRKT L ABX-1607 SEAT CLEARANCE BRKT R 601-11715 SEAT BELT 601-11162-01...
Page 221 THROTTLE UNIT (ABX-10) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1651 THROTTLE BRKT ABX-1654X THROTTLE COVER LOWER 610-0754 THROTTLE UNIT ABX 050-H00800 HEX NUT M8 060-S00800-0C SPR WSHR CRM M8 060-F00800-0B FLT WSHR BLK M8 000-T00412-0B M SCR TH BLK M4x12 068-441616-0B FLT WSHR BLK 4.4-16x1.6 ABX-60073...
Page 222 THROTTLE UNIT ABX (10-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1652X THROTTLE COVER BRKT ABX-1653X THROTTLE COVER UPPER 280-6695 SPCL WSHR 4.5-16x5 AL BLK ABX-1655 THROTTLE GRIP A ABX-1656 THROTTLE GRIP B 610-0758 THROTTLE UNIT ABX W/O GRIP 000-P00412-W M SCR PH W/FS M4x12 FAS-290042 HEX SKT LH CAP SCR STN M4x12...
Page 223 THROTTLE UNIT ABX W/O GRIP (10-0) (D-1/)
Page 224 THROTTLE UNIT ABX W/O GRIP (10-0) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1658 FRAME L ABX-1659 FRAME R ABX-1660 VR BRKT ABX-1661 SENSOR PLATE ABX-1662 SPRING SHAFT ABX-1663 GEAR BASE ABX-1664 SPRING COLLAR ABX-1665 SPRING STOPPER ABX-1666 MAIN SHAFT ABX-1667 STOP DAMPER ABX-1668...
Page 225 ASSY SEAT UPPER (ABX-100) (D-1/)
Page 226 ASSY SEAT UPPER (ABX-100) (D-/) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1701 WOODEN BASE UPPER SEAT ABX-1702 SEAT JOINT SHORT GSF-1608 SEAT JOINT ABX-1703 SEAT CUSHION CENTER ABX-1704 SEAT BACK BRKT SIDE ABX-1705 SPEAKER NET L ABX-1706 SPEAKER NET R 130-5241 SPEAKER 8OHM 15W 50x90 280-0419...
Page 227 ASSY FOOTREST C (ABX-10) ITEM NO. PART NO. DESCRIPTION NOTE ABX-1851X FOOTREST PLATE C ABX-1852 WOODEN BASE FOOTREST C ABX-1853 NON SLIP MAT C 068-441616-0B FLT WSHR BLK 4.4-16x1.6 050-F00400 FLG NUT M4...
Page 228 ROLL VOLUME UNIT (ABX-00) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3701X VOLUME BASE ABX-3702X ROLL VOLUME BRKT 601-7944 GEAR 15 440-CS0245-EG STICKER C GEAR S ENG 370-5297 PHOTO INTERRUPTER GP1A75EJ000F 220-5753 VOL CONT B-5K OHM (TOCOS) 310-5029-F20 SUMITUBE F F 20MM 280-5008 CORD CLAMP 15 280-5275-SR10...
Page 229 0 ASSY GUARD PIPE L (ABX-00) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3901 GUARD PIPE L ABX-3902 GUARD PLATE ABX-3903 CUSHION WASHER 280-6695 SPCL WSHR 4.5-16x5 AL BLK FAS-290045 HEX SKT LH CAP SCR STN M4x6 060-S00400-0C SPR WSHR CRM M4...
Page 230 1 ASSY GUARD PIPE R (ABX-0) ITEM NO. PART NO. DESCRIPTION NOTE ABX-3951 GUARD PIPE R ABX-3902 GUARD PLATE ABX-3903 CUSHION WASHER 280-6695 SPCL WSHR 4.5-16x5 AL BLK FAS-290045 HEX SKT LH CAP SCR STN M4x6 060-S00400-0C SPR WSHR CRM M4...
Page 231 ASSY I/O BD (ABX-00) ITEM NO. PART NO. DESCRIPTION NOTE ABX-4301 WOODEN BASE I/O BD 837-14505 I/O CONTROL BD FOR JVS 280-5277 CORD CLAMP 18 011-P00325 TAP SCR PH 3x25 011-F00312 TAP SCR #1 FH 3x12 ABX-60045 WH I/O BD01 ABX-60046 WH I/O BD02...
Page 232: Wire Color Code Table
WIRE COLOR CODE TABLE The DC power wire color for this product is different from previous SEGA titles. Working from the previous wire colors will create a high risk of fire. The color codes for the wires used in the diagrams in the following chapter are as follows. PINK SKY BLUE BROWN...
Page 233: Wiring Diagram
WIRING DIAGRAM (D-1/2)
Page 234 (D-2/2)

Sega AFTER BURNER CLIMAX Owner's Manual

Introduction

1 Handling Precautions

2 Precautions Regarding Installation Location

3 Precautions Regarding Product Operation

4 Part Descriptions

5 Accessories

6 Assembly and Installation

7 Precautions When Moving the Machine

8 Game Description

9 Explanation of Test and Data Display

10 Monitor

11 Control Stick

12 Throttle Lever

13 Roll Volume

14 Coin Selector

15 Replacing the Fluorescent Lamps

16 Periodic Inspection

17 Troubleshooting

18 Game Board

19 Design Related Parts

20 Network Play

21 Optional Items

22 Parts List

23 Wire Color Code Table

24 Wiring Diagram

Quick Links

Troubleshooting

Related Manuals for Sega AFTER BURNER CLIMAX

Summary of Contents for Sega AFTER BURNER CLIMAX

Table of Contents