Interlogix ATS1170 Programming Manual
  1. Manuals
  2. Brands
  3. Interlogix Manuals
  4. Remote Control
  5. ATS1170
  6. Programming manual
Interlogix ATS1170 Programming Manual

Interlogix ATS1170 Programming Manual

One door ras
Hide thumbs

Advertisement

Table of Contents

ATS1170 One Door RAS
Programming Guide
Content

Product warnings and disclaimers

THESE PRODUCTS ARE INTENDED FOR SALE TO AND
INSTALLATION BY QUALIFIED PROFESSIONALS. UTC FIRE &
SECURITY CANNOT PROVIDE ANY ASSURANCE THAT ANY
PERSON OR ENTITY BUYING ITS PRODUCTS, INCLUDING
ANY "AUTHORIZED DEALER" OR "AUTHORIZED RESELLER",
IS PROPERLY TRAINED OR EXPERIENCED TO CORRECTLY
INSTALL FIRE AND SECURITY RELATED PRODUCTS.
For more information on warranty disclaimers and product safety information,
please check
https://firesecurityproducts.com/policy/product-warning/
QR code.

Contact information

For contact information, see www.edwardsutcfs.com.
Copyright © 2018 UTC Fire & Security Americas Corporation, Inc.
All rights reserved.
P/N 14244999-1-EN • REV B • ISS 27JUN18
or scan the
1

Advertisement

Table of Contents
loading

Related Manuals for Interlogix ATS1170

Summary of Contents for Interlogix ATS1170

  • Page 1: Table Of Contents

    ATS1170 One Door RAS Programming Guide Content Product warnings and disclaimers 1 Contact information 1 Introduction 2 ATS1170 menus 2 Basic setup and programming for online access control 2 Configuring ATS1170 remotely 3 Programming cards 6 Additional Information 7 Default settings 8...

  • Page 2: Introduction

    ATS1170 can be programmed to operate with one Wiegand or one magnetic stripe card reader together with a simple Request to Exit push. ATS1170 can hold up to 15 user card numbers. For offline programming DIP switch A must be on —...

  • Page 3: Configuring Ats1170 Remotely

    The RAS display will then show: Smart Door Controller 0-Exit Menu: Key in the required ATS1170 menu number and press Enter to commence programming. You can scroll up and down the menus by using the Enter and the Menu* keys.
  • Page 4 LED 1 Armed: LED 1 is on when the area is armed, and LED 2 flashes when access is granted. • LED 1 Armed + Door Unlocked: LED 1 is on when the area is armed, and flashes when access is granted. ATS1170 One Door RAS Programming Guide...
  • Page 5 Menu* key to clear the database, it will ask you for confirmation. For default values, see “Default settings” on page 8. Display version number Go to ATS1170 menu 9–Version number. The display will show the following: Tecom Systems ver. ATS1170.Vxx Where “Vxx”...

  • Page 6: Programming Cards

    Three long beeps will sound Removing a card from the onboard user database To remove a card from the ATS1170’s database, the card format and type must match the card. Ensure Learn Mode is on – see menu 10 of ATS1170.

  • Page 7: Additional Information

    ATS1170 loses communication with the control panel, or when in permanent offline mode. DIP switch A on ATS1170 will have no effect in the online mode, however leave it in the Off position. This switch is only ever used in the offline mode to program cards. See “Basic setup and programming for offline access control”...

  • Page 8: Default Settings

    #-Exit ATS 1170 menu 11–Number of Cards in database Select menu 11–Number of Cards and press Enter to view the number of cards already held in ATS1170 database. The display will show information similar to: Number of Cards 15 #-Exit 15 being the number of cards already programmed into the database.
  • Page 9 Ten seconds after power-up, the Tx LED will flash once per second indicating ATS1170 is operating. The once per second flash rate is indicating that ATS1170 has gone into offline mode with no connection to the control panel databus.
  • Page 10 Removing a card from the onboard user database: To remove a card from the ATS1170 database, the card format and type must match the card and DIP switch A is set to On. To remove a card, badge it six times. One long beep is sounded when the card is removed from the onboard user database.

Table of Contents