The Belkin Enclosure is an industrial-grade, high-performance enclosure for the IT and telecommunication industries. The Enclosure has full compliance with the 19" rack-mount hardware EIA 310-D industry standard. The Belkin Enclosure is designed for the optimal performance of applications with servers, voice, data, networking, internetworking, cable management, power distribution, and power protection equipment.
Product Inventory Features of the Enclosure Belkin Enclosure - User Manual v 1.0.0 1 Side Panels with Locks 2 Vertical Rails (Adjustable) 3 Reversible Front Doors 4 Fully Welded Frame 5 Leveling Feet (Adjustable) 6 Casters 7 Split Rear Doors...
Before unpacking, please make sure you have the following tools: Phillips Screwdriver 3/4" Open Ended Wrench Belkin Enclosure - User Manual v 1.0.0 Utility Knife 1/2", 3/8" and 7/16" Hex Sockets Page 3...
Enclosure, slowly roll the Enclosure to the back of the skid. Proceed until all four casters contact the floor. 5. Verify that you have received all hardware and components with your Belkin Enclosure. Contact Belkin support if you feel items are missing.
1. Using two or more persons, lay your Enclosure on it's side. 2. Unscrew the levelers 3. Using a 1/2" hex socket, remove the 5/6" nuts holding the casters 4. Return Enclosure to upright position. Belkin Enclosure - User Manual v 1.0.0 Page 5 P74789...
2. Slide both latches toward the center of the side panel, and carefully pull side panel toward you. 3. Lift side panel up and remove from Enclosure. 4. To re-install, reverse above steps. Belkin Enclosure - User Manual v 1.0.0 Page 6 P74789...
Part Number RK5003 RK5004 RK5005 RK5006 Tools required: Phillips Pan Head Screw Driver Belkin Enclosure - User Manual v 1.0.0 #10-32 Phillips Pan Head Screw Description Perforated top 3 muffin fan top, 225 CFM Single 10" fan top, 500 CFM Double 10"...
Ganging or Networking your Enclosures Use Belkin part number RK5008 (optional enclosure baying kit). No additional tools required. Belkin Enclosure - User Manual v 1.0.0 Enclosure A Enclosure B Networking hole (4 locations) Page 8 1. Remove plastic button plugs from enclosure corner posts (4).
8. Rehang door. NOTE: The best time to reverse the door is prior to installing the equipment. Standard factory door configuration is left-hand hinged. Figure A Remove handle and reverse Belkin Enclosure - User Manual v 1.0.0 Figure B Page 9 P74789...
The best time to move the rails is before installation of equipment. To adjust your rails, loosen the rail bolts (4) with a 7/16" hex socket. Vertical Mounting Rail Belkin Enclosure - User Manual v 1.0.0 Use a 7/16" Hex Socket to loosen...
The ten grounding studs on the Enclosure are located on the doors, side panels, and frame. Number of studs Please refer to part number RK5038 for the optional Belkin enclosure grounding kit. Belkin Enclosure - User Manual v 1.0.0 • Load your rack from the bottom up, placing the heaviest components at the lowest position.
Cable Access • Your Belkin Enclosure provides easy cable access. • The top has two rectangular and four grommeted access points. • The rear corner posts have two integrated cable knock-outs. • These knock-outs can be removed when ganging two or more Enclosures together.
Open Rear Door Area Measured per U Wiring Clearance between Vertical Rail & Front Door* 2.5 in (6.35 cm) Static Weight Rating Dynamic Weight Rating * Front rail adjustable for additional clearance Belkin Enclosure - User Manual v 1.0.0 RK1000 RK1001 Measurement 80.25 in (203.8 cm) 24 in (60.96 cm)
Casters, Set of 4, Non-locking RK5036 Set of Four 2U High Server Brackets RK5037 Enclosure Blower, 115 Volt, 250 CFM Rating Please contact your local Belkin representative for ordering information. Belkin Enclosure - User Manual v 1.0.0 Page 17 P74789...
Belkin Corporation warrants the Belkin Enclosure for as long as the original purchaser owns it. What will we do to correct problems? Enclosure Warranty. Belkin will repair or replace, at its option, any defective Enclosure free of charge (except for shipping charges for the Enclosure). What is not covered by this Warranty?
Page 22
ITED TO, LOST BUSINESS OR PROFITS ARISING OUT OF THE SALE OR USE OF ANY BELKIN ENCLOSURE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. This Warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state.