Related Manuals for Woods Alitec CP40S
Summary of Contents for Woods Alitec CP40S
- Page 1 SKID STEER COLD PLANER CP40S/C Single Circuit Valve Effective Serial Number: 6600010303...
-
Page 2: Introduction
Use only genuine Woods service parts. Substitute parts will void the warranty and may not meet standards required for safe and satisfactory operation. Record the model number and serial number of your equipment in the spaces... -
Page 3: Table Of Contents
TABLE OF CONTENTS INTRODUCTION ..........2 GENERAL INFORMATION . -
Page 4: General Information
GENERAL INFORMATION The purpose of this manual is to assist you in operating The illustrations and data used in this manual were cur- and maintaining your planer. Read it carefully. It fur- rent at the time of printing but, due to possible inline nishes information and instructions that will help you production changes, your machine may vary slightly in achieve years of dependable performance. -
Page 5: Safety Rules
SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! must be surgically removed as soon as possible by Safety is a primary concern in the design and a doctor familiar with this form of injury or gan- manufacture of our products. Unfortunately, our grene, serious injury, or death will result. - Page 6 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Do not operate or transport equipment while under the influence of alcohol or drugs. Be sure attachment is properly secured, adjusted, and in good operating condition. Coupler Operate only in daylight or good artificial light. lockpins must be fully extended and properly ...
- Page 7 SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! or between moveable parts even when the engine Never perform service or maintenance with has been turned off. Hydraulic system leak-down, engine running. hydraulic system failures, mechanical failures, or movement of control levers can cause equipment ...
-
Page 8: Safety Decals
Replace Immediately If Damaged! SERIAL NUMBER PLATE D0193 WARNING MODEL NO. SERIAL NO. ROTATING CUTTER Keep clear during operation. Woods Equipment Company Oregon, Illinois, U.S.A. See Operator's Manual for maintenance precautions. D0193 D0404 TO AVOID SERIOUS INJURY OR DEATH: WARNING Read attachment and power unit manuals before you use, service, or repair machine. - Page 9 Skid steer must have ROPS and seat belt/operator restraint. Replacement safety decals can be ordered Keep seat belt/operator restraint securely fastened. free from your Woods dealer. To locate your Allow no riders. nearest dealer, check the Dealer Locator at RAISED EQUIPMENT CAN DROP AND CRUSH.
-
Page 10: Set-Up Instructions
SET-UP INSTRUCTIONS DRUM ASSEMBLY WARNING For proper operation, all picks or teeth must be installed in holders. Inspect picks every 4 hours of operation. If any picks show excessive wear (carbide ■ Read the entire manual as well as the decals on tip missing / damaged or pick body worn), replace all the attachment (see Safety Section), before worn picks. -
Page 11: Operation 11
OPERATION 4. Always lower the loader arms fully before leaving the skid steer seat. WARNING Safety instructions are important! Read all WARNING attachment and power unit manuals; follow all safety rules and safety decal information. (Replace- Never crawl under raised loader arms. ■... - Page 12 NOTICE With the rear gauge wheel(s) set for acceptable planing depth, the bucket function should be used for lifting or Casedrain must be attached and hose pressure ■ lowering during operation. must not exceed 15 psi. Motor seal failure will occur if the casedrain is not attached, if the hose is NOTICE crimped, or if hose pressure is excessive.
-
Page 13: Maintenance 13
MAINTENANCE NOTICE Proper maintenance of the attachment will result in longer life and the most productive and cost effective To prevent the picks from seizing in the hold- ■ operation. There are two basic categories of mainte- ers, the picks should be sprayed with diesel fuel at nance required, pick/holder replacement and compo- the end of each day. -
Page 14: Service
SERVICE 6. Sideshift the planer head slightly to the left (from the operator’s viewpoint) to remove the planetary WARNING pilot from the planer head. 7. Raise the attachment with the host vehicle; the ■ Before servicing this unit, the mandatory safety drum should remain on the floor. -
Page 15: Troubleshooting
Sand down scratches and the edges of areas of ● missing paint and coat with Woods spray paint of Periodically or Before Extended Storage matching color (purchase from your Woods ● Clean large debris such as clumps of dirt, grass, dealer). -
Page 16: Assemblies & Parts Lists
MAIN ASSEMBLY 16 Parts MCP40S/C (Rev. 4/20/2007) - Page 17 MAIN ASSEMBLY PART DESCRIPTION PART DESCRIPTION B1020 Washer, 5/8" flat USS PLT HRD 106298 Attach frame M0003 Retaining ring 1" EXT HD 102435 Back plate F1387 Fitting, 6 SLF x 6 SLM 90° 102407 Chassis T1035-1 Pin, 1" x 5.17" SR 4.5 102428 Wheel bracket M0165...
- Page 18 3-STAGE VALVE PART DESCRIPTION PART DESCRIPTION H1673 Hose #12 x 120" 12 SLF x 12 SLF HC548 Valve assembly, 3-stage single 90° circuit S0100952 Cartridge, hydac check RV16 S0100955 Coil, hydac 12V for HC548 S0100925 Cartridge, Sun Frda-Xan S0100956 Nut, coil hydac F1188 Fitting, 4 OM plug socket S0100953...
- Page 19 HYDRAULIC / ELECTRICAL SCHEMATIC Parts 19 MCP40S/C (Rev. 4/20/2007)
-
Page 20: Fitting Torque Chart
FITTING TORQUE CHART Always tighten fittings to these values unless a different torque value is listed for a specific service procedure. Make sure fastener threads are clean and threads are engaged properly. All torque values are adopted from SAE J514 and SAE J1453. SAE (JIC) O-Ring Style 37°... -
Page 21: Quick Coupler Chart
QUICK COUPLER KITS High-Flow with Auxiliary High-Flow with No Auxiliary Low-Flow Make QC Kit Description QC Kit Description QC Kit Description Bobcat HC356 Flush Face HC355 Flush Face HC357 Flush Face HC243 Poppet HC211 Ag Ball Valve Case 1013825 Flush Face HC212 Flush Face HC279... - Page 22 QUICK COUPLER KIT COMPONENTS QC KIT Includes Style Male/Female Body Hose End Size HC308 HC416 Flush Face Female SAE #12 O-ring HC417 Flush Face Male SAE #12 O-ring HC418 Flush Face Male SAE #8 O-ring HC310 HC414 Flush Face Male SAE #12 O-ring HC415 Flush Face...
- Page 23 QUICK COUPLER KIT COMPONENTS QC KIT Includes Style Male/Female Body Hose End Size 1013834 HC414 Flush Face Male SAE #12 O-ring HC415 Flush Face Female SAE #12 O-ring HC521 Flush Face Female 16 mm SAE #12 O-ring HC522 Flush Face Male 16 mm SAE #12 O-ring...
-
Page 24: Bolt Torque Chart
BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly. - Page 25 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa............Mega Pascal ASABE....
-
Page 26: Product Warranty
2. Attachments are used extensively in ground-engaging operations and, as a result, the teeth, tooth holders, cutting edges, bucket edges, ripper shanks, and other portions of the attachment are subject to abrasion and resulting wear. Woods will not accept warranty claims for wear of components or wear of areas of the attachment subject to ground-engaging wear. - Page 27 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.
- Page 28 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec- tive companies or mark holders. Specifications subject to change without notice.