Woods CSS48 Operator's Manual
  1. Manuals
  2. Brands
  3. Woods Manuals
  4. Farm Equipment
  5. CSS48
  6. Operator's manual

Woods CSS48 Operator's Manual

Compact super seeder
Hide thumbs
Table of Contents

Advertisement

Quick Links

COMPACT SUPER
SEEDER
CSS48
CSS60

Advertisement

Table of Contents
loading

Related Manuals for Woods CSS48

Summary of Contents for Woods CSS48

  • Page 1 COMPACT SUPER SEEDER CSS48 CSS60...
  • Page 2 TO THE OWNER: Read this manual before operating your Woods equipment. The information presented will prepare you to do a better and safer job. Keep this manual handy for ready reference. Require all operators to read this manual carefully and become acquainted with all adjustment and operating procedures before attempting to operate.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS INTRODUCTION ..............2 SPECIFICATIONS .

  • Page 4: Introduction

    SPECIFICATIONS CSS48 CSS60 Working Width 48" 60" Overall Width (Maximum Configuration) 56.75" 68.62" Spike Roller Pins 3/8" x 1-1/4" 3/8" x 1-1/4" No. of Roller Pins (Front and Rear) Front roller Positions 0°, 6°, 14°, 21° 0°, 6°, 14°, 21°...

  • Page 5: Safety 5

     Use extreme care and reduce ground speed on  Make sure all safety decals are installed. slopes and rough terrain. Replace if damaged. (See Safety Decals section for location.) (Safety Rules continued on next page) Safety 5 CSS48-60 Safety Rules (4/05/2019)

  • Page 6: Transportation

    MAINTENANCE  Block equipment securely for storage.  Before dismounting power unit or performing  Keep children and bystanders away from stor- any service or maintenance, follow these steps: age area.  (Rev. 8/20/2019) 6 Safety CSS48-60 Safety Rules (4/05/2019)

  • Page 7: Safety & Instructional Decals

    Replacement safety decals can be ordered free from your Woods dealer. To locate your nearest dealer, check the Dealer Locator at www.WoodsEquipment.com, or in the United States and Canada call 1-800-319-6637.
  • Page 8 SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! (Safety Decals continued from previous page) 8 - PN 1034504 6 - PN 24611 1 - PN 55121 Slow Moving Vehicle 16 - PN 20106 Red 4.5 x 2”...

  • Page 9: Operation

    OPERATION The operator is responsible for the safe operation of with front wheel weights, ballast in tires, front trac- this seeder. The operator must be properly trained. tor weights or front loader. Weigh the tractor and Operators should be familiar with the equipment, the equipment.

  • Page 10: Hitching Compact Super Seeder

    Figure 2. Seeder Hitch Positions HITCHING COMPACT SUPER SEEDER 5. Attach the safety chain to the prime mover with the maximum distance between hitch WITH TOW KIT intermediate support/primary attaching point. See Figure 3. Route safety chain through hose holder ■...

  • Page 11: Compact Super Seeder Attitude Adjustment

    DP15 Figure 4. Jack Positions Attaching Electronic Harness age tool, a nose-down attitude will provide the most aggressive tillage. When used for tillage and seeding at 1. Attach wire harness from seeder to prime mover. the same time, a level attitude is preferable. If the Com- pact Super Seeder is being used to seed already-tilled 2.

  • Page 12: Compact Super Seeder Ground Tool Operation

    2. Pin the tractor top link into the fixed top link hole. The front rollers can be angled to promote a more aggressive tearing action of the turf. The greater the 3. Lengthen the tractor top link length until the front angle, the more tearing action is applied by the front tool as been lifted off the ground a sufficient roller pins.
  • Page 13 DP15 Figure 10. Disc in Angled Position (60" Seeder Figure 8 Shown) 5. Adjust RH and LH front gang assemblies Adjusting Front Disc Angle independently. Move tubes forward (see Figure 8) for spiked front rollers. Keep RH and LH 1. Position tractor and Overseeder on a level surface. adjustment angles the same for proper operation.

  • Page 14: Seeding Operation

    6. Reinstall bent pins to hold adjusted position. Operation 7. Lift Overseeder and pull forward to clear wooden The power for operating the seeder comes from con- blocks. Lower Overseeder to rest position on the tact between the seeder rear roller and the turf. ground/level surface, and install hair pin clips (see Figure 11).

  • Page 15: Sample Seed Rate Charts

    The Legume seed box has a small seed cup and IMPORTANT adjustable fluted roller. The lever and shaft are similarly ■ Do not operate seeder in reverse. Operating adjustable to the Cool Season seed box. See Figure seeder in reverse may result in damage to seed 20.
  • Page 16 Cool Season Seed Rate Chart - Slow Drive Legume Seed Rate Chart - Fast Chain Drive 16 Operation MAN1280 (4/05/2019)
  • Page 17 Legume Seed Rate Chart - Slow Chain Drive NOTICE: These charts should only be used as guides. For more accurate rates, refer to the calibration section on pages 22 and 23. Figure 15. Transition Trays Operation 17 MAN1280 (4/05/2019)
  • Page 18 Filling the Seed Box desired. To adjust, loosen the plastic knob, move to desired position and re-tighten the knob. 1. Calibrate seeder and set seed cup rate adjustment and concaves to the correct position. Start with the seed cup at a fully closed position and open the seed cup to the desired fluted roller opening.
  • Page 19 Cool Season Seed Cup Concave Lever Adjustment Legume Seed Cup The Legume seed box is equipped with PVC tubes to The Cool Season seed cup comes equipped with an adjustable concave to handle a wide variety of seed place the legume seed in the transition tray for the Pri- mary seed box, ahead of the middle roller.
  • Page 20 Front Tool with Chain Drive Accessory Figure 23. Fast Chain Drive Figure 24. Slow Chain Drive (Rev. 8/20/2019) 20 Operation MAN1280 (4/05/2019)
  • Page 21 Figure 25. Slow Chain Drive Figure 26. Fast Chain Drive Operation 21 MAN1280 (4/05/2019)
  • Page 22 Cultipacker For Legume seed box place PVC tubes inside small canister for seed collection. The optional cultipacker can be used to firm the seed 7. Open seed cups to desired position (refer to chart bed for small seeds and increase seed-to-soil contact. for estimate) and lock into place.

  • Page 23: Transportation

    Calibration Formula Stationary Calibration Chart No. of Turns to simulate traveling 100 feet with 2 seed meters Cool Season Seed Legume Seed Reduction Reduction Shaft Turns Shaft Turns (Sprocket Teeth) (Sprocket Teeth) Fast Seed Drive 15-23 15-50 11.3 11.3 Slow Seed Drive 12-52 15-50 Multiply calibration weight by 354.4.

  • Page 24: Pre-Operation Checklist

    PRE-OPERATION CHECK LIST (OWNER’S RESPONSIBILITY) ___ Check that shields and guards are properly installed and in good condition. Replace if dam- ___ Review and follow all safety rules and safety aged. decal instructions on page 5 through page 8. ___ Check that equipment is properly and securely ___ Check all lubrication points and grease as attached to tractor.

  • Page 25: Owner Service 25

    OWNER SERVICE The information in this section is written for operators REMOVING CULTIPACKER SHAFT FROM who possess basic mechanical skills. If you need help, FRAME your dealer has trained service technicians available. 1. Place cultipacker on level, dry surface, with the For your protection, read and follow the safety informa- cultipacker wheels on the ground.

  • Page 26: Cleaning

    ● readable. Sand down scratches and the edges of areas of ● missing paint and coat with Woods spray paint of Periodically or Before Extended Storage matching color (purchase from your Woods dealer). Clean large debris such as clumps of dirt, grass, ●...

  • Page 27: Dealer Service 27

    Assembly of this equipment is the responsibility of the 7. Carefully position disc under frame and attach to 2 Woods dealer. It should be delivered to the owner com- x 3 tube using 3/4” U-bolts and nuts. Allow mounts pletely assembled, lubricated, and adjusted for normal to locate naturally to 2 x 3 tube when tightening operating conditions.
  • Page 28 Electric Tow Kit (for illustration, see page 47 & 10. Align actuator mount with slots on z-plate at the page 49) rear of seeder. Mount using 3/8” x 1-1/4” bolts and lock nuts. This mount connects the seeder frame 1. Place seeder on level surface. and frame stiffener (previously installed).
  • Page 29 ARNING NOTICE: There are two locations for the jack stand. Mount to tongue tube for storage and on “Y” section during operations. ■ Loosen jam nuts on cultipacker spring rods 5. Install tongue adjustment channel between mast until springs are unloaded before removing spring plates with 5/8”...

  • Page 30: 30 Dealer Check Lists

    DEALER CHECK LISTS PRE-DELIVERY CHECK LIST ___ Make customer aware of optional equipment available so that customer can make proper (DEALER’S RESPONSIBILITY) choices as required. Inspect the equipment thoroughly after assembly to ensure it is set up properly before delivering it to the ___ Instruct customer how to lubricate and explain customer.

  • Page 31: Parts Index

    COMPACT SUPER SEEDER CSS48, CSS60 FRAME & MIDDLE ROLLER ASSEMBLY ......32 - 33 COOL SEASON SEED BOX ASSEMBLY ......34 - 35 LEGUME SEED BOX OPTION .
  • Page 32 CSS48, CSS60 FRAME & DRIVE ROLLER ASSEMBLY 32 Parts MAN1280 (4/05/2019)
  • Page 33 CSS48, CSS60 FRAME & DRIVE ROLLER ASSEMBLY PARTS LIST PART DESCRIPTION CSS48 CSS60 20A920 1" bearing w/ housing 1042106 Pin bent .62 x 3.0 w/ washer 61163748 WA, roller 46.5" 61163760 WA, roller 58.5" 23141 HHCS 5/8 NC x 3-1/2 HT...
  • Page 34 CSS48, CSS60 COOL SEASON SEED BOX ASSEMBLY (Rev. 8/20/2019) 34 Parts MAN1280 (4/05/2019)
  • Page 35 CSS48, CSS60 COOL SEASON SEED BOX PARTS LIST PART DESCRIPTION CSS48 CSS60 61159648 WA, Primary seed box CSS48 61159660 WA, Primary seed box CSS60 611697 Mount, bearing, Primary CSS 1034694 Bearing, 1-1/8 flangette 1034717 Sprocket, RC40 15th 3/4 bore 1034693...
  • Page 36 CSS48, CSS60 LEGUME SEED BOX OPTION 36 Parts MAN1280 (4/05/2019)
  • Page 37 CSS48, CSS60 LEGUME SEED BOX PARTS LIST PART DESCRIPTION CSS48 CSS60 61160548 WA, Legume seed box CSS48 61160560 WA, Legume seed box CSS60 611649 Mount, SMV sign CSS 1001975 Flex draw latch 64812 Bolt crg 1/4 NC x 1/2 61160148...
  • Page 38 CSS48, CSS60 FRONT SPIKE ROLLER OPTION PART DESCRIPTION CSS48 CSS60 61170660 WA, roller front CSS60 61170648 WA, roller front CSS48 609308 WA, mount spiked roller CSS 61163960 Tube, hang CSS60 61163948 Tube, hang CSS48 spiked roller 20A920 1" bearing w/ housing 1035675 Slv, 1.03 x 1.25 x 0.88...
  • Page 39 CSS48, CSS60 FRONT DISC OPTION PART DESCRIPTION 1040602 Axle shaft 1.00 sq x 19.0 1038696 Disc blade 16 in. notched 1011323 Spool spacer, 3 - 5/8" 1022500 Bearing assembly, flange, 1 sq CSS48 1011324 Spool spacer, 2 - 3/8" 1022501...
  • Page 40 CSS48, CSS60 NYLON CULTIPACKER OPTION PART DESCRIPTION CSS48 CSS60 1034676 Clamp, cultipacker 1-3/4 61172348 WA, cultipacker shaft CSS48 61172360 WA, cultipacker shaft CSS60 1038781P Wheel 11 - 1/2 in. cultipacker 20A920 1" bearing w/ housing 20A111 Stud, spring 13" 20A125 Spring, comp 1.13 x .16 x 9.0 42.64...
  • Page 41 FAST CHAIN DRIVE PARTS (P/N 611740*) PART DESCRIPTION 611728 WA, sprocket RC40 15-23 611714 Chain. A2040 28 link 1034717 Sprocket, RC40 15th SU910 Bearing, needle .75 x 1.00" x .75 Standard on CSS w/ factory front spiked roller SLOW CHAIN DRIVE PARTS (P/N 611741*) PART DESCRIPTION 611727...
  • Page 42 LIGHT KIT OPTION (P/N 611743) PART DESCRIPTION 599771 Main harness, 4 ft 1040277 AG enhancer module 611744 Rear harness, 31 in. (2 pcs). 1040275 LED AG combo lamp LH 1040276 LED AG combo lamp RH 602513RP Angle, plug holder, 7 pin 14350 Nut lock 3/8 NC flange 6697...
  • Page 43 Scraper, disc blade CSS RH 51248 Bolt, crg 5/16 x 3/4 GR ZP 14139 Nut lock 5/16 NC flng HD ZP 615197 Scraper, disc blade CSS LH CSS48 - (P/N 61525048) PART DESCRIPTION 611680 Bar, scraper disc CSS48 615244 Mount, scraper disc CSS...
  • Page 44 Mount, scraper front roller CSS RH 615241 Mount, scraper front roller CSS LH 51248 Bolt crg 5/16 x 3/4 GR5 ZP 14139 Nut lock 5/16 NC flng HD ZP 61524960 Scraper, front spiked roller CSS60 61524948 Scraper, front spiked roller CSS48 44 Parts MAN1280 (4/05/2019)
  • Page 45 SPIKE DRIVE ROLLER MUD SCRAPERS OPTION (P/N 61564548 FOR CSS48) (P/N 61564560 FOR CSS60) PART DESCRIPTION 615191 Mount, scraper, rear roller CSS LH 615192 Mount, scraper, rear roller CSS RH 51248 Bolt crg 5/16 x 3/4 GR5 ZP 1046048 Nut, 5/16 round push...
  • Page 46 NYLON CULTIPACKER MUD SCRAPERS OPTION (P/N 61524648 FOR CSS48) (P/N 61524660 FOR CSS60) PART DESCRIPTION 615193 Mount, scraper cultipacker CSS LH 615194 Mount, scraper cultipacker CSS RH 51248 Bolt crg 5/16 x 3/4 GR5 ZP 14139 Nut lock 5/16 NC flng HD ZP...
  • Page 47 Nut lock 1/2 NC ZP 60969560 WA, pivot arm electric CSS60 5621 HHCS 1/2 NC x 2-3/4 GR5 60969548 WA, pivot arm electric CSS48 12169 HHCS 3/8 NC x 1-1/4 GR5 ZP 609700 WA, wheel arm right 14350 14 Nut lock 3/8 NC flng...
  • Page 48 613726 Hydraulic cylinder mount W300457 * 3 HHCS 5/8 NC x 3-3/4 GR5 ZP 61372248 Pivot arm CSS48 HYD (CSS48 only) 10380 * 4 HHCS 1/2 NC x 4 GR5 ZP 61372260 Pivot arm CSS60 HYD (CSS60 only) 765 * 4...
  • Page 49 TOW KIT WIRE HARNESS PART DESCRIPTION 616060 Harness, CSS electric tow kit (includes A & B) 616062 Module, CSS electric tow kit 616063 Wire, CSS electric tow kit 75547 12V actuator 1500 harness cnsl 35249 Clamp .50 dia steel cushion 24409 Bolt carriage 5/16 NC x 1 ZP 14562...
  • Page 50 TOW KIT HOSE ROUTING PART DESCRIPTION 1038881 Cylinder, 2 x 10, 1.06 rod 604341 Double relief valve 600 PSI 1014239 Hose 1/4 54 9/16 JICF 9/16 JICF 38673 Hose 1/4 x 94 9/16 JICF 66511 Coupler male ISO 1/2 NPT 54315 Adapter 1/2 NPTM 9/16 JICM Adapter 9/16 JICM 3/4 ORBM...

  • Page 51: Appendix 51

    BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual parts list. Always use the proper tool for tightening hardware: SAE for SAE hardware and Metric for metric hardware. Make sure fastener threads are clean and you start thread engagement properly.
  • Page 52 BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. SAE Bolt Thread Sizes 5/16 Metric Bolt Thread Sizes 10MM 12MM 14MM 16MM 18MM ABBREVIATIONS AG .............. Agriculture MPa ............Mega Pascal ASABE ....American Society of Agricultural &...

  • Page 53: Index 53

    INDEX DEALER SERVICE Transportation 23 Cultipacker 22 Dealer Set-Up Instructions 27 Filling the Seed Box 18 Optional Accessories 27 Legume Seed Cup 19 Cultipacker 27 Cool Season Seed Cup Concave Lever Adjust- Electric Tow Kit 28 ment 19 Front Disc 27 Sample Seed Rate Chart 15 Front Spike Roller 27 Seed Rate 18...
  • Page 54 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respective companies or mark holders. Specifications subject to change without notice.
  • Page 55 The limited warranty covers any defects in the material and/or workmanship. Following the proper, recommended installation by an authorized Woods Dealer and normal use of a Woods mounting and backhoe or loader, if a tractor incurs damage resulting from the attachment, Woods will cover the existing tractor warranty in the event the manufacturer voids its tractor warranty because of the attachment.
  • Page 56 Woods logo are trademarks of Woods Equipment Company. All other trademarks, trade names, or service marks not owned by Woods Equipment Company that appear in this manual are the property of their respec- tive companies or mark holders. Specifications subject to change without notice.

This manual is also suitable for:

Css60

Table of Contents