Protección Del Medio Ambiente; Environmental Protection - Skil 3610 Operating And Safety Instructions Manual

Protección del medio ambiente
Turn switch "OFF" and always remove plug from the
Las herramientas y accessorios inservibles,
WARNING
power source before trouble shooting.
deberán ser sometidas a un reciclaje
ecológico.
TROUBLE: SAW WILL NOT START
En los casos que quieras descartar su herramien-
PROBLEM 1. Power cord is not plugged in.
tas y accessorios, no tirar en la basura. Pedimos
2. Fuse or circuit breaker tripped.
que entregue a un servicio técnico autorizado Skil
3. Cord damaged.
de herramientas eléctricas que dará el destino
4. Burned out switch.
correcto, según las reglas de preservación del medio ambiente,
REMEDY 1. Plug saw in.
haciendo la reciclaje correcta de las partes, cumpliendo así con las
2. Replace fuse or reset tripped circuit breaker.
leyes locales.
3. Have cord replaced by an Authorized Skil Service Center
or Service Station.
4. Have switch replaced by an Authorized Skil Service
Center or Service Station.
TROUBLE: BLADE DOES NOT COME UP TO SPEED
PROBLEM 1. Extension cord too light or too long.
2. Low house voltage.
REMEDY 1. Replace with adequate cord.
Reservado el derecho de modificaciones
2. Contact your electric company.
TROUBLE: EXCESSIVE VIBRATION
PROBLEM 1. Failure to tighten blade angle lock.
2. Blade out of balance.
3. Saw not mounted securely to stand or workbench.
4. Arbor Nut not tight.
REMEDY 1. See "Getting To Know Your Table Saw" section, (Page
36).
2. Discard Blade and use different blade.
3. Tighten all mounting hardware,"Assembly" section.
(Page 38).
4. See "Adjustments" section, "Removal and Installation
of the Blade". (Page 37).
TROUBLE: CANNOT MAKE SQUARE CUT WHEN CROSSCUTTING
PROBLEM 1. Miter Gauge not adjusted properly.
REMEDY 1. See "Adjustments" section, "Miter Gauge Adjustment".
(Page 38).
TROUBLE: CUT BINDS, BURNS, STALLS MOTOR WHEN RIPPING
PROBLEM 1. Dull blade with improper tooth set.
2. Warped board.
3. Rip fence not parallel to blade.
2. Discard Blade and use different blade.
3. Tighten all mounting hardware,"Assembly" section.
(Page 38).
4. See "Adjustments" section, "Removal and Installation
2
of the Blade". (Page 37).
TROUBLE: CANNOT MAKE SQUARE CUT WHEN CROSSCUTTING
PROBLEM 1. Miter Gauge not adjusted properly.
REMEDY 1. See "Adjustments" section, "Miter Gauge Adjustment".
(Page 38).
TROUBLE: CUT BINDS, BURNS, STALLS MOTOR WHEN RIPPING
PROBLEM 1. Dull blade with improper tooth set.
2. Warped board.
3. Rip fence not parallel to blade.
4. Spreader out of alignment..
REMEDY 1. Sharpen or replace blade.
2. Make sure concave or hollow side is facing "DOWN"
feed slowly.
3. See "Adjustments" section "Aligning Rip Fence"
(Page 38).
TROUBLE: CUT NOT TRUE AT 90° OR 45° POSITIONS
PROBLEM 1. Alignment screws not adjusted properly.
REMEDY 1. See "Adjustments" section "Adjusting 90 & 45 Degree
Positive Stops" (Page 37).
TROUBLE: TILT LOCK HANDLE ELEVATION WHEEL HARD TO MOVE
PROBLEM 1. Blade angle lock not loosened when making tilt
adjustment.
2. Saw dust on depth screw threads.
REMEDY 1. See "Getting To Know Your Table Saw" section, "Blade
angle Lock" (Page 36).
2. See "Basic Table Saw Operation" section, "Lubrification"
(Page 40).

Environmental protection

politics of preservation of the environment, recycling parts according
the local laws.
40.
The machine, accessories and packaging
should be sorted for environmental-friendly
recycling.
If you discard your machine, accessories, do not
put off in the trash, please give it to a technical
service Skil.
It will provide a better destination according the
Subject to change without notice.