Hunter XC HYBRID Programming Manual

XC HYBRID
PROGRAMMING GUIDE
Setting the Date and Time
① Turn the dial to the CURRENT TIME/DAY
position.
② Use the
or buttons to change the year.
Press the button to proceed to setting
the month.
③ Use the or buttons to change the month.
Press the button to proceed to setting
the day.
➍ Use the or buttons to change the day.
Press the button to proceed to setting
the time.
➎ Use the and
or 24 hour. Press the
hours. Use the and
hour shown on the display. Press the
to move to minute. Use the
to change the minutes shown on the display.
The date, day, and time have now been set.
Setting the Program Start Time(s)
① Turn the dial to the START TIMES position.
② The factory preset is set on program A. You
can select program B or C by pressing the
button.
③ Use the or button to change the start
time. (The start times advance in 15-minute
increments).
➍ Press the button to add an additional start
time, or button for the next program.
NOTE: One start time will activate all stations
sequentially in that program. This eliminates
the need to enter each station's start time.
Setting Station Run Times
① Turn the dial to the Run Times position.
② The display will show the last program selected
(A, B, or C), the station number selected. You
can switch to another program by pressing the
button.
③ Use the
or button to change the station
run time on the display from 0 to 4 hours.
➍ Press the
button to advance to the next
station.
Setting Days To Water
① Turn the dial to the WATER DAYS position.
② The display will show the last program selected
(A, B, or C) switch to another program by
pressing the button.
③ The controller will display the seven days of the
week. Each day will have a
above the day. The
"On" water day, while a
an "Off" watering day.
Selecting Specific Days of the Week to Water
① With the
cursor on a specific day press the
button to activate a particular day of the
week to water. Press the
watering for that day.
buttons to select AM, PM,
button to move to
buttons to change the
button
and buttons
icon or a
icon would represent an
icon would represent
button to cancel
② Repeat step 1 until all desired days have been
selected. The selected days will show a
indicate their status is ON.
Selecting Odd or Even Days to Water
This feature uses numbered day(s) of the month
for watering instead of specific days of the week
(odd days: 1st, 3rd, 5th, etc.; even days: 2nd, 4th,
6th, etc.).
① With the
once. The
② If odd day watering is desired, turn the dial
back to the run position.
③ If even day watering is desired, press the
button once. The
displayed. You can move back and forth from
ODD to EVEN by pressing the
Selecting Interval Watering
With this option you can select interval watering
from 1 to 31 days.
① With the cursor on EVEN, press the
once and the
flashing in the display.
② Press the
of days between watering days (from 1-31 days).
The controller will water at the next start time
and will then water at the interval programmed.
Setting Event Day(s) Off
The XCH allows you to program a Non-Water
Day(s). This feature is useful to inhibit watering
on specific day(s). For example, if you always
mow the lawn on Saturdays, you would designate
Saturday as a Non-Water Day so that you are not
mowing wet grass.
① Turn the dial to the WATER DAYS position.
② Enter an interval watering schedule as
described above.
③ Press the
Days at the bottom of the display. MO will be
flashing.
➍ Use the
of the week you wish to set as a Non-Water Day.
➎ Press the
Water Day. The
➏ Repeat steps 4 and 5 until all desired event
day(s) are off.
Automatic Watering
After programming the XCH, set the dial to the
RUN position to enable automatic execution of
icon
all watering programs and start times.
System Off
Valves currently watering will be shut off after
the dial is turned to the SYSTEM OFF position for
two seconds. All active programs are discontinued
and watering is stopped. To return the controller
to normal automatic operation, simply return the
dial to the RUN position.
cursor on SU press the
icon and odd will be displayed.
icon and EVEN will be
icon will appear and a 1
or button to select the number
button to scroll to the Non-Water
button until the cursor is at the day
button to set this day as a Non-
will illuminate over this day.
to
button
and buttons.
button