Advertisement
Quick Links
Model 1689B
General Purpose
8-Channel Receiver
Installation Instructions
This manual describes the installation and operating procedures for the 1689B Eight-Channel Receiver. Receivers are designed
as the remote control device for operation of a motorized pan & tilt unit and a motorized lens unit. Since camera sites are often a
great distance from the operator's viewing location, these receivers provide the operator with positive control of the camera site.
Receivers also provide the operator with control of auxiliary devices such as lights, doors, etc. at the camera site. Receivers are
individually coded for each camera site so only the camera under observation will be controlled by the operator.
Advertisement
Related Manuals for American Dynamics AD1689B
Summary of Contents for American Dynamics AD1689B
-
Page 1: Installation Instructions
Model 1689B General Purpose 8-Channel Receiver Installation Instructions This manual describes the installation and operating procedures for the 1689B Eight-Channel Receiver. Receivers are designed as the remote control device for operation of a motorized pan & tilt unit and a motorized lens unit. Since camera sites are often a great distance from the operator’s viewing location, these receivers provide the operator with positive control of the camera site. - Page 2 This software/firmware is confidential to and is copyrighted by SENSORMATIC ELECTRONICS CORPORATION. It is not to be copied or disclosed in any manner without the express written consent of SENSORMATIC. The software is furnished to the purchaser under a license for use on a single system. NOTE: Information furnished by SENSORMATIC is believed to be accurate and reliable.
- Page 3 The installation of this product should be made by qualified service personnel and should conform to all local codes. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVERS (OR BACK) . NO USER-SERVICEABLE PARTS INSIDE.
-
Page 5: Table Of Contents
Table of Contents Product Description...1 Features ...1 Setup...2 Installation...3 Cable Connections ...4... -
Page 7: Product Description
PRODUCT DESCRIPTION The 1689B Receiver is used with matrix switching systems to control pan, tilt, zoom, focus, iris and auxiliary functions at a camera site. This receiver is classified as an eight-channel type since eight independent control channels are supplied. The 1689B will control, depending on factory configuration, eight (8) cameras with no auxiliaries, four (4) cameras with four (4) auxiliaries, or eight (8) auxiliaries. -
Page 8: Setup
SETUP SETUP There are eight pairs of rotary BCD switches which associate the camera identifiers with their respective channel. The locations of S1 through S16 on the PCB are shown in Figure 1 below. Rotary switches S1 and S2 are for the camera assigned to channel 1, switches S3 and S4 are for the camera assigned to channel 2, etc. -
Page 9: Installation
INSTALLATION This installation should be made by qualified service personnel and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and maintenance personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes. -
Page 10: Cable Connections
CONNECTIONS CABLE CONNECTIONS CAUTION - Due to the presence of non-insulated components with hazardous voltages, the following internal adjustments should be performed by qualified service personnel only. Code Line Connections The Control Code line connection to the receiver is made with user-supplied, shielded 2-wire twisted pair, Belden 8760 or equivalent (for Plenum, use Belden 88760 or equivalent). - Page 11 Pan/Tilt and Lens Cable The connections to a Pan/Tilt and a motorized lens are with 12-pin connectors. These connectors are located on the PCB, in the front of the unit with the power switch in the upper left corner. They are labeled J101 to J801 and OUT 1 to OUT 8, respectively (see Figure 1 or OP0064, OP0065 or OP0066).
- Page 12 CONNECTIONS Auxiliary Cable If the unit is configured with auxiliaries, they are connected by 12-pin connectors. For four auxiliaries these connectors, labeled J201, J401, J601 and J801 (OUT 2, OUT 4, OUT 6 and OUT 8) respectively, are located in the front of the PCB (see OP0065 or OP0066 for four and eight auxiliaries, respectively).
- Page 13 Wiring 120 VAC (U.S. - N.E.C. Standard) Model AD1689B-8 operates on an input of 120 volts AC. Use only 14 gauge copper wire for 120 volt AC power input. 1. Pass the wire through the bushing to the AC power connector.
- Page 15 Appendix...
- Page 28 17.5” H x 14.8” W x 6.7” D, NEMA 4 enclosure Weight: 18 lbs. (8 kg) 8000-0871-01 Rev E February, 1998 An American Dynamics Product Designed and built by Sensormatic Video Systems Division One Blue Hill Plaza Pearl River, New York, 10965...