Download
Share
Print this page
American Dynamics AD1645 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. American Dynamics Manuals
  4. Receiver
  5. AD1645
  6. Installation and operating instructions manual
American Dynamics AD1645 Installation And Operating Instructions Manual

American Dynamics AD1645 Installation And Operating Instructions Manual

American dynamics ad1645: install guide
Hide thumbs

Advertisement

Quick Links

Download this manual
Model 1645
Receiver

Installation and Operating Instructions

This manual describes the installation and operating procedures for the American Dynamics model 1645 Receiver. Receivers are
designed as the remote control device for operation of a motorized pan/tilt unit and a motorized lens unit. Since camera sites are
often a great distance from the operator's viewing location, these Receivers provide the operator with positive control of the
camera site. Receivers also provide the operator with control of auxiliary devices such as lights, doors etc. at the camera site.
Receivers are individually coded for each camera site, so only the camera under observation will be controlled by the operator.

Advertisement

loading

Related Manuals for American Dynamics AD1645

Summary of Contents for American Dynamics AD1645

  • Page 1: Installation And Operating Instructions

    Installation and Operating Instructions This manual describes the installation and operating procedures for the American Dynamics model 1645 Receiver. Receivers are designed as the remote control device for operation of a motorized pan/tilt unit and a motorized lens unit. Since camera sites are often a great distance from the operator’s viewing location, these Receivers provide the operator with positive control of the...
  • Page 2 NOTE: Information furnished by AMERICAN DYNAMICS is believed to be accurate and reliable. However, no responsibility is assumed by AMERICAN DYNAMICS for its use; nor for any infringements of other rights of third parties which may result from its use. No license is granted by implications or otherwise under any patent or patent rights of AMERICAN DYNAMICS.
  • Page 3 I I I I N N N N S S S S T T T T A A A A L L L L L L L L A A A A T T T T I I I I O O O O N N N N A A A A N N N N D D D D S S S S E E E E R R R R V V V V I I I I C C C C E E E E If you require information during installation of this product or if service seems necessary, contact the American Dynamics Repair and Service Department at (800) 442-2225. You must obtain a Return Authorization Number and shipping instructions before returning any product for service.

  • Page 4: Table Of Contents

    Table of Contents Description... 1 Features... 1 Installation ... 2 Setup ... 3 Camera Number Assignment ... 3 Lens Voltage Adjust ... 3 Receiver Configuration Setup ... 3 Local Test Mode ... 4 RS-232 Receiver Setup... 5 Connections ... 6 Control Code ...

  • Page 5: Description

    The 1645 Receiver is a single channel receiver for control of motorized pan/tilt and lens units used with Matrix Switching Systems. The 1645 is used with the American Dynamics 1237VS or Videor Technical VPT-21 Pan/Tilt unit to control the pan, tilt, zoom, focus, and iris of a single camera, and to control auxiliary functions at a camera site.

  • Page 6: Installation

    INSTALLATION INSTALLATION This installation should be made by a qualified service person and should conform to all local codes. Safeguards must be taken to avoid unintentional operation by employees and personnel working about the premises, by falling objects, by customers, by building vibration, and by similar causes. Preparation Several user configuration switches must be set (see SETUP instructions, pages 3 to 5) prior to the connection and operation...

  • Page 7: Setup

    SETUP Camera Number Assignment For individual control of camera Pan/Tilt actions by the Matrix Switching System, a camera number must be associated with each Receiver. A 10-position DIP switch labeled “CAMERA ID” is used to associate a particular camera number with the Receiver.

  • Page 8: Local Test Mode

    SETUP Local Test Mode Local Test Mode provides the ability to control a 1645 Receiver without a code line connected. This capability can be used with either Control Code or RS-232 Receivers. The Local Test Mode feature is operated as follows, using internal switches S1, S2, and S5.

  • Page 9: Rs-232 Receiver Setup

    RS-232 Receiver (1645S) Setup In order to receive RS-232 code, the S1 and S2 DIP switches on the RS-232 Receiver Module must be set to the following positions. See Figure 5 below for location of these DIP switches on the 1645S Receiver Module PCB. DIP Sw.

  • Page 10: Connections

    CONNECTIONS CONNECTIONS Code Line Connections for Control Code (model 1645M) The Code Terminal Connector, J1, is a 3-position terminal connector located on the side of the unit (see Figure 4, page 4). The terminal is marked W (white code), S (shield), and B (black code).
  • Page 11 For proper RS-232 communications, both the pin definitions and the EIA Standard DTE (Data Terminal Equipment) designation of each piece of equipment must be observed. All American Dynamics equipment, including the 1645 Receiver, are DTE equipment. For DTE/DTE communications between an RS-232 device and the 1645S Receiver: 1.

  • Page 12: Pan/Tilt And Lens Cable

    CONNECTIONS Table 7 - Pan/Tilt and Lens 12-pin Connector Pinout (J6) PIN NO. FUNCTION FOCUS ZOOM IRIS COMMON +20 VDC TILT -20 VDC SHIELD ALARM 1 ALARM 2 GROUND Pan/Tilt and Lens Cable The connection to a Pan/Tilt and a motorized Lens is with a 12-pin connector.

  • Page 13: Auxiliary And Preposition Cable

    Table 8 - Preposition Pan/Tilt and Auxiliary 14-pin Connector Pinout (J7) PIN NO. FUNCTION + REF PAN 1 POT PAN 2 POT TILT POT FOCUS POT ZOOM POT - REF SHIELD AUX 1 - NORMALLY CLOSED ____________________ AUX 1 - NORMALLY OPEN AUX 1 - COMMON AUX 2 - NORMALLY CLOSED ____________________ AUX 2 - NORMALLY OPEN...

  • Page 14: Operation

    OPERATION OPERATION Powering Up The 1645 Receiver is supplied for the following power sources: 1645M,1645S 120VAC, 50/60Hz 1645MX,1645SX 230VAC, 50/60Hz The 1645 Receivers are shipped with a pendant cord and wall plug for use with an electrical outlet. Plug the cord to the required voltage source according to the model.
  • Page 15 Appendix...
  • Page 17 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0...
  • Page 18 Appendix 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0 0 0 1 0 0...
  • Page 19 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0 0 0 0 1 0 0 1 0 0 0 0...
  • Page 20 Appendix 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0 0 0 1 1 0...
  • Page 21 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 0 0 1 1 0 0 0 0 0 0 0 0 1 0 1 0 0 0 0...
  • Page 22 Appendix 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 1 1 0 0 0 0...
  • Page 23 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 0 1 1 0 1 0 0 0 0...
  • Page 24 Appendix 1645M models, set switch positions 7-10 Off; 1645S models, set the switches in the shaded section of the table Camera Switch Position Number 1 2 3 4 5 6 7 8 9 10 0 0 0 0 0 0 1 0 0 0 0 0 0 1 0 0 0 0 1 1 0 0 0 0...

  • Page 25: Typical System Connections

    TYPICAL SYSTEM CONNECTIONS 1237VS PAN/TILT ALARM 2 ALARM 1 SHIELD - 20 VDC TILT + 20 VDC COMMON IRIS ZOOM FOCUS 1645 RECEIVER 1645 to 1237VS Pan/Tilt 7-Pin 1237VS Connector...
  • Page 26 TYPICAL SYSTEM CONNECTIONS 1645 to 1237VSP Pan/Tilt with Pre-position ALARM 2 ALARM 1 SHIELD - 20 VDC TILT + 20 VDC COMMON IRIS ZOOM FOCUS 1645 RECEIVER 1237VSP PAN/TILT 11-Pin 1237VSP + REF PAN1 POT PAN2 POT TILT POT FOCUS POT ZOOM POT - REF SHIELD...
  • Page 27 1996 Controller to 2091 Code Generator, to 1645M (Control Code) DATA LINE SELECT CODE ABCDEF B W S B W S B W S B W S ABCDEF B W S B W S B W S B W S ABCDEF B W S B W S B W S B W S ABCDEF...
  • Page 28 TYPICAL SYSTEM CONNECTIONS 2150 Controller to 1645M (Control Code) ALARMS RELAY CODE BWS BWS BWS BWS MONITORS 120V 60Hz KEYBOARDS CAMERAS RS232 PORTS 2150 B W S MAXIMUM DISTANCE between 1645 and 2150 is 5000 Ft, using shielded, 18 AWG cable W S B 1645M...
  • Page 29 1676 Keyboard to 1645S (RS-232 Connection) JJ0007 Cable HP0047 TERMINAL BOX BROWN (GRD) GREEN (XMIT) MAXIMUM DISTANCE between 1645 and 1676 is 1000 Ft, using shielded, 18 AWG cable TYPICAL SYSTEM CONNECTIONS 1676 TP8059 Wall Transformer (RCD) 1645S...
  • Page 30 LINE PHONE HP0047 TERMINAL BOX BROWN (GRD) (XMIT) GREEN (RCD) TYPICAL SYSTEM CONNECTIONS 1983 Code Converter to 1645S (RS-232 Connection) CODE RS232 JJ0007 Cable 120V 60Hz 1983 1645S...
  • Page 31 1996 Controller to 2091, to 1645S (RS-232 Connection) DATA LINE SELECT CODE ABCDEF B W S B W S B W S B W S ABCDEF B W S B W S B W S B W S ABCDEF B W S B W S B W S B W S ABCDEF B W S B W S B W S B W S JJ0007 Cable...
  • Page 32 Weight: 4.5 lbs (2 Kg) 8000-2894-01 May 1994 120VAC, 50/60 Hz 230VAC, 50/60 Hz An American Dynamics Product Designed and built by Sensormatic CCTV Systems Division One Blue Hill Plaza Pearl River, New York, 10965 (914) 624-7600 Technical Support Center: 1-800-442-2225...

This manual is also suitable for:

1645