Table of Contents
Advertisement
04/2013
Brief overview of all commands
Command
Parameter
PIN
1 0
X X X X
Dialing register
1 1
X X
Dialing register
Tel. call number
1 2
X X
Y...Y
Dialing register
1 3
X X
Dialing register
1 4
X X
Communication time in s
1 5
X X
Number of call signals
1 6
X
Activation time in s
1 7
X X
Block number
1 8
X X
Control
1 9
X
0=PSTN 1=PBX 2=Hotline
2 0
X
Exchange code
2 1
X
X X
oder
Digit of the quick dial button
2 2
4
5
6
or
or
0=OFF
1=ON
2 3
0
1
or
0=Call
1=TOE
2=Day/Night
2 4
0
1
2
or
or
0=Button 7
1=speak immed.
2 5
0
1
or
Dial delay in s
2 6
0
1
9
...
or
or
Dialing register Dial st. successor
2 7
X X
Y Y
Dialing register dial st. (NIGHT)
2 8
X X
Y Y
Dialing register activation time
2 9
X X
Y Y
Dialing register call time
3 0
X X
YY
0=low priority. / 1=medium priority
/
2=high priority
3 1 X
0=OFF 1=ON
3 2
X
TCS TürControlSysteme AG, TCS Hotline Germany: +49 (0) 41 94/ 9 88 11 88
FAX: +49 (0) 41 94/ 9 88 129 Mail: hotline@tcsag.de
13
Programming the FBO1100
End of
com-
Function
mand
*
Enter a PIN
*
Determine dialing register number for the sensor
*
Enter or delete
(no YYYY)
*
Checks the content of the dialing register XX
*
Assignment of a TK-Interface dialing register to a bell button
*
Setting the minimum duration of a conversation,
88 s = unlimited
(entry 11: 1 min, entry 12: 2 min, ... entry 19: 9 min)
*
Determine the number of calls until the TK-Interface accepts the
call
*
Setting the activation time of the output port at
Button (10=10s / 11=1s / ...19=9s / 20s ... 90s)
*
Setting the block number for the TK-Interface
*
Service function Eavesdropping
0 = can be activated with the button Reload factory setting
1 = activate always automatically
*
Setting the exchange type
*
Enter the exchange code,
(special case 01=FLASH / 02=MFV* / 03=MFV# / 04=FLASH + MFV* / 05=FLASH
+ MFV* + MFV* / 06=MFV* + MFV*)
*
Train an internal client on the buttons 4 / 5 / 6
Delete the buttons 4 / 5 / 6
*
Control remote maintenance
*
Define the function of the sensor
*
Define the type of the connection start
ATTENTION, not in case of a call diversion!
*
Setting the delay of the dial start
(special case 0 = controlled by tone)
*
Enter the successor (YY) to the dialing register XX in case of a
call diversion
*
add the night dialing register ID to the storage space XX in case
of day / night mode
*
Activation of the actuator when calling via
dialing register XX, 0 = OFF
88 = door release automatic, TCS:BUS command
*
Duration of the call for this dialing register
*
Controlling the establishment of the connection
*
Controlling the switch-off tone while calling a front-door station
a call number in the dialing register XX
Subject to technical changes.
PI_FBO1100_uk 1A
Factory setting
of the parame-
ter
0 0 0 0
10...
deleted
none
none
(13)
3 min
2
10
72
10/
/24/10
0
0
0
none
0
0
1
3
deleted
deleted
0
3 0
2
1
Advertisement
Table of Contents
