Removing And Replacing The Cushions; Replacing The Helmet Attachment Plate; Spare Parts And Accessories; Communicate Face To Face (Push-To-Listen) - 3M PELTOR WS LiteCom Pro III Manual

EN
radio and the phone call.
Operating your Bluetooth ® device via the headset
NOTE: The latest paired Bluetooth
operate via the headset.
®
Bluetooth Scenario Action
(Bluetooth
on the left cup)
®
If Bluetooth device Long press
is connected but no
activity
®
If Bluetooth device Short press
is connected and
receiving an incoming
Long press
call
If Bluetooth ® device Short press
is connected, and has
an ongoing call
SMART TIP: You can also stream music from your Bluetooth
device.
If Bluetooth ® Short press
device is
Double short
connected, and
press
streaming is
ongoing Triple short press
Long press
Communicate via connected external radio
Connect your external communication radio via the auxiliary
port (cable not included). To transmit, use the PTT button on
the radio or external PTT adapter.

Communicate face to face (Push-To-Listen)

The surround microphones can be activated from off or low
state with a double press on the On/Off/Mode button.
The Push-To-Listen feature enables you to instantly listen to
your environment by muting the FM radio and Bluetooth
volume and activating the level-dependent microphones.
Press any other button to deactivate Push-To-Listen.

CLEANING AND MAINTENANCE

Use a cloth wetted with soap and warm water to clean the
cups, headband and cushions.
NOTE: Do NOT immerse the hearing protector in water.
If the hearing protector gets wet from rain or sweat, turn the
earmuffs outwards, remove the cushions and foam liners, and
allow to dry before reassembly. See Spare Parts Section
below. Keep the earmuffs clean and dry and store in
recommended storage temperature in a clean uncontaminated
area before and after use.
®
device is the one you
Feature
® button
Voice dial
Answer call
Reject call
Hang up
®
Play/Pause
Next track
Previous track
Voice dial
® audio
7

Removing and replacing the cushions

H:1 H:2
H:2 To replace, insert the foam liners.
H:3 Fit one side of the cushion into the groove of the cup and
then press on the opposite side until the cushion snaps in
place.

Replacing the helmet attachment plate

I:2
I:1
helmet attachment plate may need to be replaced. Find the
recommended attachment in Table B. The headset comes
assembled with a P3E helmet attachment, while other plates
can be obtained from your dealer. A screwdriver is needed to
replace the helmet attachment plate.
I:1 Loosen the screw holding the plate and remove the plate.
I:2 Attach the appropriate plate while ensuring the left (L) and
right (R) designated plates are on the appropriate earmuff, if
applicable, and then tighten the screw.

SPARE PARTS AND ACCESSORIES

3M™ PELTOR™ ACK081 Battery
3M™ PELTOR™ AL2AI Battery charging cable for ACK081
3M™ PELTOR™ FR08 Power supply
3M™ PELTOR™ FL5602 External PTT for WS™ LiteCom
Pro III Headset
Push-To-Talk button with connection cable for external control
of transmission with the radio in the 3M™ PELTOR™ WS™
LiteCom Pro III Headset.
3M™ PELTOR™ FL6CS Connecting cable
With 2.5 mm stereo connector for use with DECT and mobile
telephones.
3M™ PELTOR™ FL6BT Connecting cable
With 3.5 mm mono connector for use with a communication
radio.
3M™ PELTOR™ FL6BR Connecting cable
With PELTOR™ J11 connector (type Nexus TP-120) for use
with a PELTOR™ adapter and an external communication
radio. Contact your Authorised 3M™ PELTOR™ LiteCom Pro
H:3